It fixes a problem for the last chunk where 'chunk_size' is smaller than
MLXSW_I2C_BLK_MAX and data is copied to the wrong offset, overriding
previous data.
Fixes: 6882b0aee1 ("mlxsw: Introduce support for I2C bus")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASIC has the ability to generate events whenever a sensor indicates
the temperature goes above or below its high or low thresholds,
respectively.
In new firmware versions the firmware enforces a minimum of 5
degrees Celsius difference between both thresholds. Make the driver
conform to this requirement.
Note that this is required even when the events are disabled, as in
certain systems interrupts are generated via GPIO based on these
thresholds.
Fixes: 85926f8770 ("mlxsw: reg: Add definition of temperature management registers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function of_parse_phandle() returns a NULL pointer if it cannot
resolve a phandle property to a device_node pointer. In function
hns_nic_dev_probe(), its return value is passed to PTR_ERR to extract
the error code. However, in this case, the extracted error code will
always be zero, which is unexpected.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function netdev_priv() returns the private data of the device. The
memory to store the private data is allocated in alloc_netdev() and is
released in netdev_free(). Calling kfree() on the return value of
netdev_priv() after netdev_free() results in a double free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fix 5987feb38a ("net: phy: marvell: logical vs bitwise OR typo")
uncovered another bug in the Marvell PHY driver, which broke the
Marvell OpenRD platform. It relies on the bootloader configuring the
RGMII delays and does not specify a phy-mode in its device tree. The
PHY driver should only configure RGMII delays if the phy mode
indicates it is using RGMII. Without anything in device tree, the
mv643xx Ethernet driver defaults to GMII.
Fixes: 5987feb38a ("net: phy: marvell: logical vs bitwise OR typo")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The most important here is the security vulnerabitility fix for
ath10k.
ath10k
* fix security vulnerability with missing PN check on certain hardware
* revert ath10k napi fix as it caused regressions on QCA6174
wcn36xx
* remove unnecessary rcu_read_unlock() from error path
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ+JEXAAoJEG4XJFUm622bxlYH/RVFveiBV/5v3Edj7bfQaonm
DrSO9fWNi+B3d2S0jpP/E9aPAZFfI6lrJ2zYbmyHEtIgLmWUsCgpkPbsTiE7Qa/7
VesLt5cDQyE25F9C3N2cNgaSI2VrHVml13GZ1f9329us/pUyPhzT7SKVO5c3SIjf
PcnyobgRtT42tJWYGDJ83tP9EaGQnIcxVcjrH5Bfp7SiOLlWh05owDBQKyxni+8Q
NAF/CAqaeXOTygL8f/A4mmp/qAolPzSp3XpyFWNOP3UdfI+sgLNbc8BDo1COzHMw
of9SF0RZi8Vy65x9xZKwxnzkmUmp0F7GX/MpkO2vI9Zhca8XlXCVb30t6pDqSLc=
=iqP1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
The most important here is the security vulnerabitility fix for
ath10k.
ath10k
* fix security vulnerability with missing PN check on certain hardware
* revert ath10k napi fix as it caused regressions on QCA6174
wcn36xx
* remove unnecessary rcu_read_unlock() from error path
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git fixes for 4.14. Major changes:
ath10k
* fix security vulnerability with missing PN check on certain hardware
* revert ath10k napi fix as it caused regressions on QCA6174
wcn36xx
* remove unnecessary rcu_read_unlock() from error path
Thorsten reported on <fa6e3ee2-91b5-a54b-afe3-87f30aac7a48@leemhuis.info> that
commit c9353bf483 made ath10k unstable with QCA6174 on his Dell XPS13 (9360)
with an error message:
ath10k_pci 0000:3a:00.0: failed to extract amsdu: -11
It only seemed to happen with certain APs, not all, but when it happened the
only way to get ath10k working was to switch the wifi off and on with a hotkey.
As this commit made things even worse (a warning vs breaking the whole
connection) let's revert the commit for now and while the issue is being fixed.
Link: http://lists.infradead.org/pipermail/ath10k/2017-October/010227.html
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx data frames notified through HTT_T2H_MSG_TYPE_RX_IND and
HTT_T2H_MSG_TYPE_RX_FRAG_IND expect PN/TSC check to be done
on host (mac80211) rather than firmware. Rebuild cipher header
in every received data frames (that are notified through those
HTT interfaces) from the rx_hdr_status tlv available in the
rx descriptor of the first msdu. Skip setting RX_FLAG_IV_STRIPPED
flag for the packets which requires mac80211 PN/TSC check support
and set appropriate RX_FLAG for stripped crypto tail. Hw QCA988X,
QCA9887, QCA99X0, QCA9984, QCA9888 and QCA4019 currently need the
rebuilding of cipher header to perform PN/TSC check for replay
attack.
Please note that removing crypto tail for CCMP-256, GCMP and GCMP-256 ciphers
in raw mode needs to be fixed. Since Rx with these ciphers in raw
mode does not work in the current form even without this patch and
removing crypto tail for these chipers needs clean up, raw mode related
issues in CCMP-256, GCMP and GCMP-256 can be addressed in follow up
patches.
Tested-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The commit 9a393b5d59 ("tap: tap as an independent module") created a
separate tap module that implements tap functionality and exports
interfaces that will be used by macvtap and ipvtap modules to create
create respective tap devices.
However, that patch introduced a regression wherein the modules macvtap
and ipvtap can be removed (through modprobe -r) while there are
applications using the respective /dev/tapX devices. These applications
cause kernel to hold reference to /dev/tapX through 'struct cdev
macvtap_cdev' and 'struct cdev ipvtap_dev' defined in macvtap and ipvtap
modules respectively. So, when the application is later closed the
kernel panics because we are referencing KVA that is present in the
unloaded modules.
----------8<------- Example ----------8<----------
$ sudo ip li add name mv0 link enp7s0 type macvtap
$ sudo ip li show mv0 |grep mv0| awk -e '{print $1 $2}'
14:mv0@enp7s0:
$ cat /dev/tap14 &
$ lsmod |egrep -i 'tap|vlan'
macvtap 16384 0
macvlan 24576 1 macvtap
tap 24576 3 macvtap
$ sudo modprobe -r macvtap
$ fg
cat /dev/tap14
^C
<...system panics...>
BUG: unable to handle kernel paging request at ffffffffa038c500
IP: cdev_put+0xf/0x30
----------8<-----------------8<----------
The fix is to set cdev.owner to the module that creates the tap device
(either macvtap or ipvtap). With this set, the operations (in
fs/char_dev.c) on char device holds and releases the module through
cdev_get() and cdev_put() and will not allow the module to unload
prematurely.
Fixes: 9a393b5d59 (tap: tap as an independent module)
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An unaligned alloc_frag->offset caused by previous allocation will
result an unaligned skb->head. This will lead unaligned
skb_shared_info and then unaligned dataref which requires to be
aligned for accessing on some architecture. Fix this by aligning
alloc_frag->offset before the frag refilling.
Fixes: 0bbd7dad34 ("tun: make tun_build_skb() thread safe")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Wei Wei <dotweiba@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reported-by: Wei Wei <dotweiba@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-10-26
This series contains fixes to e1000, igb, ixgbe and i40e.
Vincenzo Maffione fixes a potential race condition which would result in
the interface being up but transmits are disabled in the hardware.
Colin Ian King fixes a possible NULL pointer dereference in e1000, which
was found by Coverity.
Jean-Philippe Brucker fixes a possible kernel panic when a driver cannot
map a transmit buffer, which is caused by an erroneous test.
Alex provides a fix for ixgbe, which is a partial revert of the commit
ffed21bcee ("ixgbe: Don't bother clearing buffer memory for descriptor rings")
because the previous commit messed up the exception handling path by
adding the count back in when we did not need to. Also fixed a typo,
where the transmit ITR setting was being used to determine if we were
using adaptive receive interrupt moderation or not. Lastly, fixed a
memory leak by including programming descriptors in the cleaned count.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
According to DWMAC databook the first queue operating mode
must always be in DCB.
As MTL_QUEUE_DCB = 1, we need to always set the first queue
operating mode to DCB otherwise driver will think that queue
is in AVB mode (because MTL_QUEUE_AVB = 0).
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to DT bindings documentation we are expecting a
property called "snps,read-requests" but we are parsing
instead a property called "read,read-requests".
This is clearly a typo. Fix it.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No rcu_read_lock is called, but rcu_read_unlock is still called.
Thus rcu_read_unlock should be removed.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-10-26
The series includes some misc fixes for mlx5 core and etherent driver.
Please pull and let me know if there's any problem.
For -Stable:
net/mlx5e: Properly deal with encap flows add/del under neigh update (kernels >= 4.12)
net/mlx5: Fix health work queue spin lock to IRQ safe (kernels >= 4.13)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the i40e driver to include programming descriptors in
the cleaned_count. Without this change it becomes possible for us to leak
memory as we don't trigger a large enough allocation when the time comes to
allocate new buffers and we end up overwriting a number of rx_buffers equal
to the number of programming descriptors we encountered.
Fixes: 0e626ff7cc ("i40e: Fix support for flow director programming status")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It looks like there was either a copy/paste error or just a typo that
resulted in the Tx ITR setting being used to determine if we were using
adaptive Rx interrupt moderation or not.
This patch fixes the typo.
Fixes: 65e87c0398 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a partial revert of "ixgbe: Don't bother clearing buffer
memory for descriptor rings". Specifically I messed up the exception
handling path a bit and this resulted in us incorrectly adding the count
back in when we didn't need to.
In order to make this simpler I am reverting most of the exception handling
path change and instead just replacing the bit that was handled by the
unmap_and_free call.
Fixes: ffed21bcee ("ixgbe: Don't bother clearing buffer memory for descriptor rings")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver cannot map a TX buffer, instead of rolling back
gracefully and retrying later, we currently get a panic:
[ 159.885994] igb 0000:00:00.0: TX DMA map failed
[ 159.886588] Unable to handle kernel paging request at virtual address ffff00000a08c7a8
...
[ 159.897031] PC is at igb_xmit_frame_ring+0x9c8/0xcb8
Fix the erroneous test that leads to this situation.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the stat type is invalid then data[i] is being set
either by dereferencing a null pointer p, or it is reading from
an incorrect previous location if we had a valid stat type
previously. Fix this by skipping over the read of p on an invalid
stat type.
Detected by CoverityScan, CID#113385 ("Explicit null dereferenced")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a race condition that can result into the interface being
up and carrier on, but with transmits disabled in the hardware.
The bug may show up by repeatedly IFF_DOWN+IFF_UP the interface, which
allows e1000_watchdog() interleave with e1000_down().
CPU x CPU y
--------------------------------------------------------------------
e1000_down():
netif_carrier_off()
e1000_watchdog():
if (carrier == off) {
netif_carrier_on();
enable_hw_transmit();
}
disable_hw_transmit();
e1000_watchdog():
/* carrier on, do nothing */
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Double free of skb_array in tap module is causing kernel panic. When
tap_set_queue() fails we free skb_array right away by calling
skb_array_cleanup(). However, later on skb_array_cleanup() is called
again by tap_sock_destruct through sock_put(). This patch fixes that
issue.
Fixes: 362899b872 (macvtap: switch to use skb array)
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAlnvHlATHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9tBJB/9sLLdYdtrp0L1KlJ+PNVjNcq993ai4
6wlh0ay+JKiMZzepkEEYjI8lFdFVxmvB9czOL3FgV6Cb2tW7/vTs3gtv1LuvA92o
9QsOXQtH/KO+bbuPiHPRvuSMO56OMZtxrJSK0prdkodOimDWwnkLZ4jHStNjvmIt
wuE4fYH8K9jp80qtyQ9Al0COvR+ePZtfaDWn3YhO0swEUfcClALl2OqUd2MRl3Ut
dkfbCoGCR7PNnFDNxPACoOu0FLUl01iLDf5fWx43SLKwFhnjf6eomkukyBTzrBT4
bHsPT4hYMkkA+YCQ5TmTDlK6IRwXfvIkgSimFItFE+t+0Rfr2XFIrnps
=IxfN
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.14-20171024' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-10-24
here's another pull request for net/master.
The patch by Gerhard Bertelsmann fixes the CAN_CTRLMODE_LOOPBACK in the
sun4i driver. Two patches by Jimmy Assarsson for the kvaser_usb driver
fix a print in the error path of the kvaser_usb_close() and remove a
wrong warning message with the Leaf v2 firmware version v4.1.844.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces GFP_KERNEL by GFP_ATOMIC to avoid sleeping in the
ndo_set_rx_mode() call which is called with BH disabled.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling mvpp2_prs_mac_multi_set() from mvpp2_prs_mac_init(), two
parameters (the port index and the table index) are inverted. Fixes
this.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo in the mvpp2_prs_tcam_data_cmp() function, as
the shift value is inverted with the data.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, tc with ets type and zero bandwidth is not accepted
by driver. This behavior does not follow the IEEE802.1qaz spec.
If there are tcs with ets type and zero bandwidth, these tcs are
assigned to the lowest priority tc_group #0. We equally distribute
100% bw of the tc_group #0 to these zero bandwidth ets tcs.
Also, the non zero bandwidth ets tcs are assigned to tc_group #1.
If there is no zero bandwidth ets tc, the non zero bandwidth ets tcs
are assigned to tc_group #0.
Fixes: cdcf11212b ("net/mlx5e: Validate BW weight values of ETS")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, the encap action offload is handled in the actions parse
function and not in mlx5e_tc_add_fdb_flow() where we deal with all
the other aspects of offloading actions (vlan, modify header) and
the rule itself.
When the neigh update code (mlx5e_tc_encap_flows_add()) recreates the
encap entry and offloads the related flows, we wrongly call again into
mlx5e_tc_add_fdb_flow(), this for itself would cause us to handle
again the offloading of vlans and header re-write which puts things
in non consistent state and step on freed memory (e.g the modify
header parse buffer which is already freed).
Since on error, mlx5e_tc_add_fdb_flow() detaches and may release the
encap entry, it causes a corruption at the neigh update code which goes
over the list of flows associated with this encap entry, or double free
when the tc flow is later deleted by user-space.
When neigh update (mlx5e_tc_encap_flows_del()) unoffloads the flows related
to an encap entry which is now invalid, we do a partial repeat of the eswitch
flow removal code which is wrong too.
To fix things up we do the following:
(1) handle the encap action offload in the eswitch flow add function
mlx5e_tc_add_fdb_flow() as done for the other actions and the rule itself.
(2) modify the neigh update code (mlx5e_tc_encap_flows_add/del) to only
deal with the encap entry and rules delete/add and not with any of
the other offloaded actions.
Fixes: 232c001398 ('net/mlx5e: Add support to neighbour update flow')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_ib_add is called during mlx5_pci_resume after a pci error.
Before mlx5_ib_add completes, there are multiple events which trigger
function mlx5_ib_event. This cause kernel panic because mlx5_ib_event
accesses unitialized resources.
The fix is to extend Erez Shitrit's patch <97834eba7c19>
("net/mlx5: Delay events till ib registration ends") to cover
the pci resume code path.
Trace:
mlx5_core 0001:01:00.6: mlx5_pci_resume was called
mlx5_core 0001:01:00.6: firmware version: 16.20.1011
mlx5_core 0001:01:00.6: mlx5_attach_interface:164:(pid 779):
mlx5_ib_event:2996:(pid 34777): warning: event on port 1
mlx5_ib_event:2996:(pid 34782): warning: event on port 1
Unable to handle kernel paging request for data at address 0x0001c104
Faulting instruction address: 0xd000000008f411fc
Oops: Kernel access of bad area, sig: 11 [#1]
...
...
Call Trace:
[c000000fff77bb70] [d000000008f4119c] mlx5_ib_event+0x64/0x470 [mlx5_ib] (unreliable)
[c000000fff77bc60] [d000000008e67130] mlx5_core_event+0xb8/0x210 [mlx5_core]
[c000000fff77bd10] [d000000008e4bd00] mlx5_eq_int+0x528/0x860[mlx5_core]
Fixes: 97834eba7c ("net/mlx5: Delay events till ib registration ends")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
spin_lock/unlock of health->wq_lock should be IRQ safe.
It was changed to spin_lock_irqsave since adding commit 0179720d6b
("net/mlx5: Introduce trigger_health_work function") which uses
spin_lock from asynchronous event (IRQ) context.
Thus, all spin_lock/unlock of health->wq_lock should have been moved
to IRQ safe mode.
However, one occurrence on new code using this lock missed that
change, resulting in possible deadlock:
kernel: Possible unsafe locking scenario:
kernel: CPU0
kernel: ----
kernel: lock(&(&health->wq_lock)->rlock);
kernel: <Interrupt>
kernel: lock(&(&health->wq_lock)->rlock);
kernel: #012 *** DEADLOCK ***
Fixes: 2a0165a034 ("net/mlx5: Cancel delayed recovery work when unloading the driver")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If the name argument of dev_get_valid_name() contains "%d", it will try
to assign it a unit number in __dev__alloc_name() and return either the
unit number (>= 0) or an error code (< 0).
Considering positive values as error values prevent tun device creations
relying this mechanism, therefor we should only consider negative values
as errors here.
Signed-off-by: Julien Gomes <julien@arista.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we did not ensure that a netdev is a representative netdev
before dereferencing its private data. This can occur when an upper netdev
is created on a representative netdev. This patch corrects this by first
ensuring that the netdev is a representative netdev before using it.
Checking only switchdev_port_same_parent_id is not sufficient to ensure
that we can safely use the netdev. Failing to check that the netdev is also
a representative netdev would result in incorrect dereferencing.
Fixes: 1a1e586f54 ("nfp: add basic action capabilities to flower offloads")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid kernel warning "Unhandled message (68)", ignore the
CMD_FLUSH_QUEUE_REPLY message for now.
As of Leaf v2 firmware version v4.1.844 (2017-02-15), flush tx queue is
synchronous. There is a capability bit indicating whether flushing tx
queue is synchronous or asynchronous.
A proper solution would be to query the device for capabilities. If the
synchronous tx flush capability bit is set, we should wait for
CMD_FLUSH_QUEUE_REPLY message, while flushing the tx queue.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the return value from kvaser_usb_send_simple_msg() was non-zero, the
return value from kvaser_usb_flush_queue() was printed in the kernel
warning.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix loopback mode by setting the right flag and remove presume mode.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When Tx IRQs are used, txq_bufs_free() can be called from both the Tx
path and from NAPI poll(). This led to CPU stalls as if these two tasks
(Tx and Poll) are scheduled on two CPUs at the same time, DMA unmapping
operations are done on the same txq buffers.
This patch adds a check not to call txq_done() from the Tx path if Tx
interrupts are used as it does not make sense to do so.
Fixes: edc660fa09 ("net: mvpp2: replace TX coalescing interrupts with hrtimer")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO header buffers are coming from a per cpu pool and should not
be unmapped as they are reused. The PPv2 driver was unmapping all
descriptors buffers unconditionally. This patch fixes this by checking
the buffers dma addresses before unmapping them, and by not unmapping
those who are located in the TSO header pool.
Fixes: 186cd4d4e4 ("net: mvpp2: software tso support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO headers are managed with txq index and therefore should be aligned
with the txq size, not with the aggregated txq size.
Fixes: 186cd4d4e4 ("net: mvpp2: software tso support")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Huawei ME906 (12d1:15c1) comes with a standard ECM interface that
requires management via AT commands sent over one of the control TTYs
(e.g. connected with AT^NDISDUP).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
This product is named 'TP-LINK USB 3.0 Gigabit Ethernet Network
Adapter (Model No.is UE300)'. It uses chip RTL8153 and works with
driver drivers/net/usb/r8152.c
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"A little more than usual this time around. Been travelling, so that is
part of it.
Anyways, here are the highlights:
1) Deal with memcontrol races wrt. listener dismantle, from Eric
Dumazet.
2) Handle page allocation failures properly in nfp driver, from Jaku
Kicinski.
3) Fix memory leaks in macsec, from Sabrina Dubroca.
4) Fix crashes in pppol2tp_session_ioctl(), from Guillaume Nault.
5) Several fixes in bnxt_en driver, including preventing potential
NVRAM parameter corruption from Michael Chan.
6) Fix for KRACK attacks in wireless, from Johannes Berg.
7) rtnetlink event generation fixes from Xin Long.
8) Deadlock in mlxsw driver, from Ido Schimmel.
9) Disallow arithmetic operations on context pointers in bpf, from
Jakub Kicinski.
10) Missing sock_owned_by_user() check in sctp_icmp_redirect(), from
Xin Long.
11) Only TCP is supported for sockmap, make that explicit with a
check, from John Fastabend.
12) Fix IP options state races in DCCP and TCP, from Eric Dumazet.
13) Fix panic in packet_getsockopt(), also from Eric Dumazet.
14) Add missing locked in hv_sock layer, from Dexuan Cui.
15) Various aquantia bug fixes, including several statistics handling
cures. From Igor Russkikh et al.
16) Fix arithmetic overflow in devmap code, from John Fastabend.
17) Fix busted socket memory accounting when we get a fault in the tcp
zero copy paths. From Willem de Bruijn.
18) Don't leave opt->tot_len uninitialized in ipv6, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
stmmac: Don't access tx_q->dirty_tx before netif_tx_lock
ipv6: flowlabel: do not leave opt->tot_len with garbage
of_mdio: Fix broken PHY IRQ in case of probe deferral
textsearch: fix typos in library helpers
rxrpc: Don't release call mutex on error pointer
net: stmmac: Prevent infinite loop in get_rx_timestamp_status()
net: stmmac: Fix stmmac_get_rx_hwtstamp()
net: stmmac: Add missing call to dev_kfree_skb()
mlxsw: spectrum_router: Configure TIGCR on init
mlxsw: reg: Add Tunneling IPinIP General Configuration Register
net: ethtool: remove error check for legacy setting transceiver type
soreuseport: fix initialization race
net: bridge: fix returning of vlan range op errors
sock: correct sk_wmem_queued accounting on efault in tcp zerocopy
bpf: add test cases to bpf selftests to cover all access tests
bpf: fix pattern matches for direct packet access
bpf: fix off by one for range markings with L{T, E} patterns
bpf: devmap fix arithmetic overflow in bitmap_size calculation
net: aquantia: Bad udp rate on default interrupt coalescing
net: aquantia: Enable coalescing management via ethtool interface
...
This is the possible reason for different hard to reproduce
problems on my ARMv7-SMP test system.
The symptoms are in recent kernels imprecise external aborts,
and in older kernels various kinds of network stalls and
unexpected page allocation failures.
My testing indicates that the trouble started between v4.5 and v4.6
and prevails up to v4.14.
Using the dirty_tx before acquiring the spin lock is clearly
wrong and was first introduced with v4.6.
Fixes: e3ad57c967 ("stmmac: review RX/TX ring management")
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent infinite loop by correctly setting the loop condition to
break when i == 10.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using GMAC4 the valid timestamp is from CTX next desc but
we are passing the previous desc to get_rx_timestamp_status()
callback.
Fix this and while at it rework a little bit the function logic.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX HW timestamp is enabled and a frame is discarded we are
not freeing the skb but instead only setting to NULL the entry.
Add a call to dev_kfree_skb_any() so that skb entry is correctly
freed.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum tunnels do not default to ttl of "inherit" like the Linux ones
do. Configure TIGCR on router init so that the TTL of tunnel packets is
copied from the overlay packets.
Fixes: ee954d1a91 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIGCR register is used for setting up the IPinIP Tunnel
configuration.
Fixes: ee954d1a91 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default Tx rates cause very long ISR delays on Tx.
0xff is 510us delay, giving only ~ 2000 interrupts per seconds for
Tx rings cleanup. With these settings udp tx rate was never higher than
~800Mbps on a single stream. Changing min delay to 0xF makes it
way better with ~6Gbps
TCP stream performance is almost unaffected by this change, since LSO
optimizations play important role.
CPU load is affected insignificantly by this change.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia NIC allows both TX and RX interrupt throttle rate (ITR)
management, but this was used in a very limited way via predefined
values. This patch allows to setup ITR default values via module
command line arguments and via standard ethtool coalescing settings.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
