There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior this patch, the internal debugging was based on ifdef
and also some printk were useless because many info are exposed
via ethtool.
This patch remove all the ifdef defines and now we only use
netif_msg_XXX levels.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the EEE setup allowing to configure this support
when the link changes.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tidies up the code. I have run Linden (and verified with checkpatch)
many part of the driver trying to reorganize some sections respecting the
codying-style rules in the points where it was not done.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements PHC (ptp hardware clock) driver for stmmac
driver to support 1588 PTP.
V2: added support for FINE method, reduced loop delay and review spinlock.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances the stmmac driver to support IEEE 1588-2002
PTP (Precision Time Protocol) version 1 and IEEE 1588-2008 PPT
version 2.
Precision Time Protocol(PTP),which enables precise synchronization
of clocks in measurement and control systems implemented with
technologies such as network communication,local computing,
& distributed objects.
Both PTPv1 and PTPv2 is selected at run-time using the HW capability
register.
The PTPv1 TimeStamp support can be used on chips that have the normal
descriptor structures and PTPv2 TimeStamp support can be used on chips
that have the Extended descriptors(DES4-5-6-7). All such sanity checks
are done and verified by using HW capability register.
V2: in this version the ethtool support has been included in this patch;
Koptions have been completely removed (previously added to select
PTP and PTPv2). PTPv1 and PTPv2 is now added in a single patch instead of
two patches.
get_timestamp() and get_systemtime() L/H have been combined into single APIs.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the minimal support to manage the PCS
modes (RGMII/SGMII) and restart the ANE.
Both TBI and RTBI are not yet supported.
Thanks to Byungho that wrote some part of this code
and tested SGMII too.
The only thing to be fixed is the get/set pause in
ethtool.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch starts adding in the main ISR the management of the PCS and
RGMII/SGMII core interrupts. This is to help further development
on this area. Currently the core irq handler only clears the
PCS and S-R_MII interrupts and reports the event in the ethtool stats.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Byungho An <bh74.an@samsung.com>
Cc: Udit Kumar <udit-dlh.kumar@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to support the extend descriptors available
in the chips newer than the 3.50.
In case of the extend descriptors cannot be supported,
at runtime, the driver will continue to work using the old style.
In detail, this support extends the main descriptor structure
adding new descriptors: 4, 5, 6, 7. The desc4 gives us extra
information about the received ethernet payload when it is
carrying PTP packets or TCP/UDP/ICMP over IP packets.
The descriptors 6 and 7 are used for saving HW L/H timestamps (PTP).
V2: this new version removes the Koption added in the first implementation
because all the checks now to verify if the extended descriptors are
actually supported happen at probe time.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we had two Koptions to decide if the stmmac
had to use either a ring or a chain to manage its descriptors.
This patch removes the Kernel configuration options and it allow us
to use the chain mode by passing a module option.
Ring mode continues to be the default.
Also with this patch, it will be easier to validate the driver built and
guarantee that all the two modes always compile fine.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC devices newer than databook 3.40 has an embedded timer
that can be used for mitigating the number of interrupts.
So this patch adds this optimizations.
At any rate, the Rx watchdog can be disable (on bugged HW) by
passing from the platform the riwt_off field.
In this implementation the rx timer stored in the Reg9 is fixed
to the max value. This will be tuned by using ethtool.
V2: added a platform parameter to force to disable the rx-watchdog
for example on new core where it is bugged.
V3: do not disable NAPI when Rx watchdog is used.
V4: a new extra statistic field has been added to show the early
receive status in the interrupt handler.
This patch also adds an extra check to avoid to call
napi_schedule when the DMA_INTR_ENA_RIE bit is disabled in the
Interrupt Mask register.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new schema used for mitigating the
number of transmit interrupts.
It is based on a SW timer and a threshold value.
The timer is used to periodically call the stmmac_tx_clean
function; the threshold is used for setting the IC (Interrupt
on Completion bit). The ISR will then invoke the poll method.
Also the patch improves some ethtool stat fields.
V2: review the logic to manage the IC bit in the TDESC
that was bugged because it didn't take care about the
fragments. Also fix the tx_count_frames that has not to be
limited to TX DMA ring. Thanks to Ben Hutchings.
V3: removed the spin_lock irqsave/restore as D. Miller suggested.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds "#ifndef __<header>_H" for protecting header from double
inclusion.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Energy Efficient Ethernet support to the stmmac.
Please see the driver's documentation for further details about this support
in the driver.
Thanks also goes to Rayagond Kokatanur for his first implementation.
Note:
to clearly manage and expose the lpi interrupt status and eee ethtool
stats I've had to do some modifications to the driver's design and I
found really useful to move other parts of the code (e.g. mmc irq stat)
in the main directly. So this means that some core has been reworked
to introduce the EEE.
v1: initial patch
v2: fixed some sparse issues (typos)
v3: erroneously sent the v2 renamed as v3
v4:
o Fixed the return value of the stmmac_eee_init as suggested by D.Miller
o Totally reviewed the ethtool support for EEE
o Added a new internal parameter to tune the SW timer for TX LPI.
v5: do not change any eee setting in case of the stmmac_ethtool_op_set_eee fails
(it has to return -EOPNOTSUPP in that case).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mixed burst (MB) mode, the AHB master always initiates
the bursts with fixed-size when the DMA requests transfers
of size less than or equal to 16 beats.
This patch adds the MB support and the flag that can be
passed from the platform to select it.
MB mode can also give some benefits in terms of performances
on some platforms.
v2: fixed Coding Style
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to extend the number of MAC address registers
for 16 to 32. In fact, other new 16 registers are available in new
chips and this can help on perfect filter mode for unicast.
This patch also fixes the perfect filtering mode by setting the
bit 31 in the MAC address registers.
v2: fixed Coding Style.
Signed-off-by: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the dma parameters that can be passed from the platform
have been moved from the plat_stmmacenet_data to the stmmac_dma_cfg.
In case of this new structure is not well allocated the driver can
fails. This is an example how this field is managed in ST platforms
static struct stmmac_dma_cfg gmac_dma_setting = {
.pbl = 32,
};
static struct plat_stmmacenet_data stih415_ethernet_platform_data[] = {
{
.dma_cfg = &gmac_dma_setting,
.has_gmac = 1,
[snip]
This patch so verifies that the dma_cfg passed from the platform.
In case of it is NULL there is no reason that the driver has to fail
and some default values can be passed. These are ok for all the
Synopsys chips and could impact on performances, only.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
cc: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a specific clk_csr value is passed from the platform
this means that the CSR Clock Range selection cannot be
changed at run-time and it is fixed (as reported in the driver
documentation). Viceversa the driver will try to set the MDC
clock dynamically according to the actual clock input.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Reviewed-by: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch re-works the internal GMAC DMA parameters
passed from the platform.
In the past, we only passed the pbl but, with new core,
other parameters can be passed and are mandatory on some
platforms.
New parameters are documented in stmmac.txt because this
patch has an impact for many platforms.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sanities the RX coe and adds the Type-1 Rx checksum offload engine (COE).
So the RX COE can be passed through the platform but can be fixed
at run-time in case of the core has the HW capability register.
Also to support the Type-1 Rx COE the driver must append the
HW checksum at the end of payload in case the Rx checksum
engine was used to offload the HW checksum.
This v2 version also fixes the IPC that has to be enabled and verified.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this bit is set and the CRC error is reset, then the packet is valid.
Only report this as stat info.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PCI support (as EXPERIMENTAL)
this has been also tested on XLINX XC2V3000 FF1152AMT0221
D1215994A VIRTEX FPGA board.
To support the PCI bus the main part has been reworked
and both the platform and the PCI specific parts have
been moved into different files.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the normal descriptor structure
to work fine on new GMAC Synopsys chips.
Normal descriptors were designed on the old MAC10/100
databook 1.91 where some bits were reserved: for example
the tx checksum insertion and rx checksum offload.
The patch maintains the back-compatibility with old
MAC devices (tested on STx7109 MAC10/100) and adds new
fields that actually new GMAC devices can use.
For example, STx7109 (MAC10/100) will pass from the platform
tx_coe = 0, enh_desc = 0, has_gmac = 0.
A platform like Loongson1B (GMAC) will pass:
tx_coe = 1, enh_desc = 0, has_gmac = 1.
Thanks to Kelvin, he enhanced the normal descriptors for
GMAC (on MIPS Loongson1B platform).
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances the STMMAC driver to support CHAINED mode of
descriptor.
STMMAC supports DMA descriptor to operate both in dual buffer(RING)
and linked-list(CHAINED) mode. In RING mode (default) each descriptor
points to two data buffer pointers whereas in CHAINED mode they point
to only one data buffer pointer.
In CHAINED mode each descriptor will have pointer to next descriptor in
the list, hence creating the explicit chaining in the descriptor itself,
whereas such explicit chaining is not possible in RING mode.
First version of this work has been done by Rayagond.
Then the patch has been reworked avoiding ifdef inside the C code.
A new header file has been added to define all the functions needed for
managing enhanced and normal descriptors.
In fact, these have to be specialized according to the ring/chain usage.
Two new C files have been also added to implement the helper routines
needed to manage: jumbo frames, chain and ring setup (i.e. desc3).
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New GMAC chips have an extra register to indicate
the presence of the optional features/functions of
the DMA core.
This patch adds this support and all the HW cap
are exported via debugfs.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Synopsys ID is now passed from the MAC core
to the main. This info will be used for managing
the HW cap register (supported in the new GMAC
generations).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the MMC management counters support.
MMC module is an extension of the register address
space and all the hardware counters can be accessed
via ethtoo -S ethX.
Note that, the MMC interrupts remain masked and the logic
to handle this kind of interrupt will be added later (if
actually useful).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DWMAC Management Counters (MMC) are not fully support.
The minimal support added in the past allowed to
only disable counters (if present) and mask their
interrupts.
This patch prepares the driver to support the MMC
removing obsolete code.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the STMicroelectronics driver into driver/net/ethernet/stmicro/ and
make the necessary Kconfig and Makefile changes.
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
