EM28174 is very similar as already supported EM2874.
I am not sure what are differences, but it could be analog support.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register multiple FEs for same adapter. After that it is
possible to register two FEs for same adapter. For example
one for DVB-T and one for DVB-C.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the PCTV 330e remote control
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the flag indicating the 330e board is not validated, based on the half
dozen users who have reported today that everything is working.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the calls necessary to use the new drx-d driver for the PCTV 330e
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Given how PCTV has multiple products with the same model name, include the
model number in the description and #define to make it a little more clear.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx bridge strobes the reset pin on the drx-d on every ts_ctrl call.
This results in the state of the chip getting out of the sync with the
state of the driver (and hence all tuning requests after the first one fail).
Make sure the drx-d is not being held in reset, but don't actually perform a
hardware reset on the chip.
The GPIO block has been split out from the other HVR-9x0 variants to reduce
the risk of regression, although in theory they would not have any issues
since none of those cases have the frontend driver managing any internal
state.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the tuner is not actually behind an i2c gate, using the i2c gate control
function can wedge the i2c bus. Provide the ability to control on a per-board
basis whether it should be used.
Problem was noticed on the HVR-900 R2, where it resulted in the first tuning
attempt succeeding, and then all subsequent attempts to access the xc3028
being treated as failures (including the call to sleep the tuner).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The rc-hauppauge-new map is a messy thing, as it bundles 3
different remote controllers as if they were just one,
discarding the address byte. Also, some key maps are wrong.
With the conversion to the new rc-core, it is likely that
most of the devices won't be working properly, as the i2c
driver and the raw decoders are now providing 16 bits for
the remote, instead of just 8.
delete mode 100644 drivers/media/rc/keymaps/rc-hauppauge-new.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
There are two "hauppauge-new" keymaps, one with protocol
unknown, and the other with the protocol marked accordingly.
However, both tables are miss-named.
Also, the old rc-hauppauge-new is broken, as it mixes
three different controllers as if they were just one.
This patch solves half of the problem by renaming the
correct keycode table as just rc-hauppauge. This table
contains the codes for the four different types of
remote controllers found on Hauppauge cards, properly
mapped with their different addresses.
create mode 100644 drivers/media/rc/keymaps/rc-hauppauge.c
delete mode 100644 drivers/media/rc/keymaps/rc-rc5-hauppauge-new.c
[Jarod: fix up RC_MAP_HAUPPAUGE defines]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Subdev controls return codes are evil, as they return -EINVAL to mean
both unsupported and invalid arguments. Due to that, we need to use a
trick to identify what controls are supported by a subdev.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On some cases, driver returns 1. This should be OK, but qv4l2 is too
strict about return values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The core.s_config op was meant for legacy drivers that needed to work with old
pre-2.6.26 kernels. This is no longer relevant. Unfortunately, this op was
incorrectly called from several drivers.
Replace those occurences with proper i2c_board_info structs and call
v4l2_i2c_new_subdev_board.
After these changes v4l2_i2c_new_subdev_cfg() was no longer used, so remove
that function as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to a lack of a break inside the switch, it were getting the
wrong keytable and get_key function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
em28xx uses core assisted locking, so it shouldn't use .ioctl.
The .ioctl callback was replaced by .unlocked_ioctl for video nodes,
but not for radio nodes. This is now corrected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Calling subdevs to handle s_ctrl returned a non-zero return code even if
everything went fine.
Calling STREAMOFF if no STREAMON happened earlier would hit a BUG_ON
in res_free.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I found that the problems people have reported with the USB-TV-stick
"Terratec Cinergy Hybrid T USB XS" (USB-ID: 0ccd:0042)
are coming from a wrong header file in the v4l-sources.
Attached is a diff, which fixes the problem (tested successfully here).
Obviously the USB-ID has been associated with a wrong chip: EM2880
instead of EM2882, which would be correct.
Reported-by: Philippe Bourdin <richel@AngieBecker.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,IR_TYPE,RC_TYPE,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_type,rc_type,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Remote Controller subsystem is meant to be used not only by Infra Red
but also for similar types of Remote Controllers. The core is not specific
to Infra Red. As such, rename:
- ir-core.h to rc-core.h
- IR_CORE to RC_CORE
- namespace inside rc-core.c/rc-core.h
To be consistent with the other changes.
No functional change on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch merges the ir_input_dev and ir_dev_props structs into a single
struct called rc_dev. The drivers and various functions in rc-core used
by the drivers are also changed to use rc_dev as the primary interface
when dealing with rc-core.
This means that the input_dev is abstracted away from the drivers which
is necessary if we ever want to support multiple input devs per rc device.
The new API is similar to what the input subsystem uses, i.e:
rc_device_alloc()
rc_device_free()
rc_device_register()
rc_device_unregister()
[mchehab@redhat.com: Fix compilation on mceusb and cx231xx, due to merge conflicts]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx88 only depends on VIDEO_IR because it needs ir_extract_bits().
Move that function to ir-core.h and make it inline.
Lots of drivers had dependencies on VIDEO_IR when they really
wanted IR_CORE.
The only remaining drivers to depend on VIDEO_IR are bt8xx and
saa7134 (ir_rc5_timer_end is the only function exported by
ir-functions).
Rename VIDEO_IR -> IR_LEGACY to give a hint to anyone writing or
converting drivers to IR_CORE that they do not want a dependency
on IR_LEGACY.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device uses an em2874B + Sharp 921 One Seg frontend.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Video drivers request submodules using a work during probe and calls
flush_scheduled_work() on exit to make sure the work is complete
before being unloaded. This patch makes these drivers flush the work
directly instead of using flush_scheduled_work().
While at it, relocate request_submodules() call in saa7134_initdev()
right right before successful return as in other drivers to avoid
failing after the work is scheduled and returning failure without the
work still active.
This is in preparation for the deprecation of flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago. Convert all the
in-kernel users. The conversions are completely equivalent and
trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
The argument isn't used anymore by the functions, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the drivers
modified here use.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch allows this device successfully to show video, at least from
its composite input.
I have no information about the true hardware contents of this device and so
this patch is based solely on fiddling with things until it worked. The
chip appears to be em2860, and the closest device with equivalent inputs
is the Typhoon DVD Maker. Copying the settings for that device appears
to do the trick. That's what this patch does.
[mchehab@redhat.com: update CARDLIST.em28xx accordingly, via script]
Signed-off-by: Adrian Taylor <adrian.taylor@realvnc.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial em28xx std (PAL) was not passed on to the subdevs. This led to
these tvp5150 kernel log errors when running v4l2-ctl --all:
tvp5150 0-005c: VBI can't be configured without knowing number of lines
The reason was that tvp5150 was still using its own internal default: STD_ALL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an ext_lock argument to the videobuf init functions. This allows
drivers to pass the vdev->lock pointer (or any other externally held lock)
to videobuf. For now all drivers just pass NULL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB: v4l2-ctrls.c: needs to include slab.h
V4L/DVB: fix Kconfig to depends on VIDEO_IR
V4L/DVB: Fix IR_CORE dependencies
The probe method used by i2c_new_probed_device() may not be suitable
for all cases. Let the caller provide its own, optional probe
function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for the KWorld PlusTV 340U and KWorld UB345-Q ATSC
sticks, which are really the same device. The sticks have an eMPIA
em2870 usb bridge chipset, an LG Electronics LGDT3304 ATSC/QAM
demodulator and an NXP TDA18271HD tuner -- early versions of the 340U
have a a TDA18271HD/C1, later models and the UB435-Q have a C2.
The stick has been tested succesfully with both VSB_8 and QAM_256 signals.
Its using lgdt3304 support added to the lgdt3305 driver by a prior patch,
rather than the current lgdt3304 driver, as its severely lacking in
functionality by comparison (see said patch for details).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of generating one printk for every IR read, prints it only when
count is different from the last count.
While here, as this code is called on every 100ms during the runtime
lifetime, do some performance optimization, assuming that, under normal
circumstances, it is unlikely that the driver would get a new key/key
repeat on every poll.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
