Previously only the resources controlled by the driver were put into
low power state at system suspend. Both the amba bus and a potential
power domain were ignored.
Moreover, while putting the device into low power state we first
brought it back to full power, but for no particular reason.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to the SET_PM_RUNTIME_PM macro while defining the runtime PM
callbacks. This means the callbacks becomes available for both
CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME, which is needed to handle the
combinations of these scenarios.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver core is now taking care of putting our pins into default
state at probe. Thus we can remove the redundant call for it in probe.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make use of clk_prepare_enable and clk_disable_unprepare to simplify
code. No functional change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the driver was converted to clk_prepare() the suspend path didn't
have any changes made so the clock remains prepared throughout the runtime
of the driver. Unprepare it when suspended so that any savings that can be
made as a result are made.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Change raw printk() call to dev_info() to provide a better message
to userspace so it can properly identify the device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_spi_register_master() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
'break' immediately after return has no effect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When CONFIG_ARM_LPAE=y the following build warning is generated:
drivers/spi/spi-pl022.c:2178:9: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'resource_size_t' [-Wformat]
According to Documentation/printk-formats.txt '%pa' can be used to properly
print 'resource_size_t'.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
In the past we controlled the selection of DMA for a certain
host by a boolean switch in the platform data. Currently
there is no way to enable DMA on a PL022 probed from the
device tree. Let's default to trying to obtain DMA channels
in the DT case, and then we can always fail (and thus fall
back to PIO mode).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This utilize the new pinctrl core PM helpers to transition
the driver to "sleep" and "idle" states, cutting away some
boilerplate code.
Cc: Hebbar Gururaja <gururaja.hebbar@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the new OF DMA binding, it is possible to completely avoid the
need for platform_data for configuring a DMA channel. In cases where the
platform has already been converted, calling dma_request_slave_channel
should get all the necessary information from the device tree.
Like the patch that converts the dw_dma controller, this is completely
untested and is looking for someone to try it out.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: spi-devel-general@lists.sourceforge.net
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A bunch of fixes here, mostly minor except for the pl022 which has just
been a bit of a shambles all round, the recent runtime PM changes have
as far as I can tell never worked so they're just getting thrown out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=9XvI
-----END PGP SIGNATURE-----
Merge tag 'spi-linus' into spi-next
spi: Fixes for v3.7
A bunch of fixes here, mostly minor except for the pl022 which has just
been a bit of a shambles all round, the recent runtime PM changes have
as far as I can tell never worked so they're just getting thrown out.
Conflicts:
drivers/spi/spi-pl022.c
[Originally sent by Ulf as two changes, squashed down into one with a
redone changelog, thanks to Russell King for analysis. -- broonie]
This reverts commit 688723 (spi/pl022: enable runtime PM) and commit
2fb30d (spi/pl022: fix spi-pl022 pm enable at probe).
Commit "spi/pl022: enable runtime PM" introduced runtime PM issues as it
interacted badly with the work Russell King had done to move core
runtime PM handling into the bus. Due to that commit, "spi/pl022: fix
spi-pl022 pm enable at probe" was merged to fix part of those issues.
Instead of adding another fix, let's clean up and revert everything
back to when it was already fine.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Revert "spi/pl022: enable runtime PM"
Conflicts:
drivers/spi/spi-pl022.c
This commit allow to put pins in IDLE state in
runtime_suspend and in SLEEP state in suspend, corresponding
to defined semantics in <linux/pinctrl/pinctrl-state.h>.
To do this, just add a boolean parameter runtime
to pl022_resume_resources/pl022_suspend_resources which
indicates if it's called from PM_RUNTIME callbacks or not.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To be able to deactivate resourses in suspend, the resourses must
first be surely active. This is done with a pm_runtime_get_sync.
Once the resourses are restored to active state again in resume,
the runtime pm usage count can be decreased with a pm_runtime_put.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In probe pm_runtime_put_autosuspend has the same effect as doing
pm_runtime_put. This due to upper layer in driver core is preventing
the device from being runtime suspended by a pm_runtime_get*.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This reverts commit 6887237cd7.
Commit "spi/pl022: enable runtime PM" introduced runtime PM issues.
Due to that commit, "spi/pl022: fix spi-pl022 pm enable at probe"
was merged to fix part of those issues.
Instead of adding another fix, let's clean up and revert everything
back to when it was already fine.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This factors out the resource handling in runtime
suspend/resume and also calls it from the ordinary suspend
and resume hooks.
The semantics require that ordinary PM op suspend is called
with runtime PM in resumed mode, so that ordinary suspend
can assume that it will e.g. decrease the clock reference
counter to 0, runtime resume having previously increased it
to 1.
Cc: Vipul Kumar Samar <vipulkumar.samar@st.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This switches the PL022 SPI driver to use devm_* managed resources
for IRQ, clocks, ioremap and GPIO. Prior to this, the GPIOs would
even leak.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Even with devicetree support, we needed platform data to provide some data,
leading to mixed device tree and platform data. This patch makes it possible to
provide all that information via device tree. Now, the data must be provided
via platform data _or_ device tree completely.
Only in case of DMA where a callback specification is necessary (dma_filter()),
platform data is the only option.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Amend the PL022 pin controller to optionally take a pin control
handle and set the state of the pins to "default" on boot and
runtime resume, and to "sleep" at runtime suspend. This way we
will dynamically save power on the SPI busses, for example some
electronic designs may be able to ground the pins when unused
instead of pull-up. Some pin controllers may want to set the
pins as wake-up sources when sleeping.
Effect on platforms using the PL022 driver:
- If the platform does not use pin control - no semantic effect,
the pinctrl stubs will kick in and resolve the situation.
- Platforms using this driver and have pin control but no
function defined for the PL022 need to either supply a
"default" function in their map or enable pinctrl dummies
so the driver is satisfied.
- Platforms using this driver with hogs for setting up the PL022
pin control - stop using hogs to take the pl022 pin control
handle, let the driver handle this.
I'be looked at some platforms that may be affected:
- SPEAr: appears to define the proper functions in their device
trees and not hogging them, so things should be smooth, the
driver will simply start to take its pins.
- Ux500: the proper function is defined and will be taken properly
by the driver. New sleep states introduced by a separate patch to
ux500 but no regression, since the default state is sufficient.
- U300: old hog deleted as part of this patch.
- LPC32xx: does not appear to be using pinctrl.
- ARM Integrator IMPD1, RealView & Versatile: does not use pinctrl.
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The new chip select handling via GPIO introduced a pointer computation bug:
(int *) pl022 + sizeof(struct pl022)
doesn't point to the data immediately after the actual struct pl022 (as was
intended) but to a multiple of bytes after it because of the (int *) type.
Replacing the kludgy pointer arithmetic with managed memory allocation for the
chip selects.
Reported-by: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds device tree support to the spi-pl022 driver.
Based on the initial patch by Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the ability for the driver to control the chip select directly.
This enables independence from cs_control callbacks. Configurable via
platform_data, to be extended as DT in the following patch.
Based on the initial patch by Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The call sequence spi_alloc_master/spi_register_master/spi_unregister_master
is complete; it reduces the device reference count to zero, which results in
device memory being freed. An extra call to spi_master_put is unnecessary
and results in an access to free memory. Drop it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
amba drivers does not need to enable pm runtime at probe.
amba_probe already enables pm runtime.
This rids this warning in the ux500 boot log:
ssp-pl022 ssp0: Unbalanced pm_runtime_enable!
Signed-off-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we're gonna use runtime PM it's a pretty good idea to actually
enable it in probe() and disable it in remove() too, so it
gets used for real. Up until now we only fooled around with the
reference count.
Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This ASIC variant has been deleted from the ARM tree, no need
to keep support around.
Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit ffbbdd2132
"spi: create a message queueing infrastructure"
Accidentally deleted the logic to disable the port
when unused leading to higher power consumption.
Fix this up.
Cc: stable@kernel.org
Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, if we request for frequency greater than maximum possible, spi driver
returns error.
For example, if the spi block src frequency is 333/4 MHz, i.e. 83.33.. MHz,
maximum frequency programmable would be src/2. Which would come around 41.6...
It is difficult to pass frequency in these figures. We normally try to program
in round figures, like 42 MHz and it should get programmed to <=
requested_frequency, i.e. 41.6...
For this to happen, we must not return error even if requested freq is higher
than max possible. But should program it to max possible.
Reported-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
calculate_effective_freq() was still not optimized and there were cases when it
returned without error and with values of cpsr and scr as zero.
Also, the variable named found is not used well.
This patch targets to optimize and correct this routine. Tested for SPEAr.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
pl022 ssp controller supports word lengths from 4 to 16 (or 32) bits.
Currently implemented checks were incorrect. It has following check
if (pl022->vendor->max_bpw >= 32)
which must be checking for <=.
Also error print message is incorrect, that prints "range is from 1 to
16".
Fix both these issues.
Signed-off-by: Vinit Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The AMBA bus regulator support is being used to model on/off switches
for power domains which isn't terribly idiomatic for modern kernels with
the generic power domain code and creates integration problems on platforms
which don't use regulators for their power domains as it's hard to tell
the difference between a regulator that is needed but failed to be provided
and one that isn't supposed to be there (though DT does make that easier).
Platforms that wish to use the regulator API to manage their power domains
can indirect via the power domain interface.
This feature is only used with the vape supply of the db8500 PRCMU
driver which supplies the UARTs and MMC controllers, none of which have
support for managing vcore at runtime in mainline (only pl022 SPI
controller does). Update that supply to have an always_on constraint
until the power domain support for the system is updated so that it is
enabled for these users, this is likely to have no impact on practical
systems as probably at least one of these devices will be active and
cause AMBA to hold the supply on anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
Mostly a bunch of new drivers and driver bug fixes; but this also
includes a few patches that create a core message queue infrastructure
for the spi subsystem instead of making each driver open code it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6Nsu
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI changes for v3.4 from Grant Likely:
"Mostly a bunch of new drivers and driver bug fixes; but this also
includes a few patches that create a core message queue infrastructure
for the spi subsystem instead of making each driver open code it."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/fsl-espi: Make sure pm is within 2..32
spi/fsl-espi: make the clock computation easier to read
spi: sh-hspi: modify write/read method
spi: sh-hspi: control spi clock more correctly
spi: sh-hspi: convert to using core message queue
spi: s3c64xx: Fix build
spi: s3c64xx: remove unnecessary callback msg->complete
spi: remove redundant variable assignment
spi: release lock on error path in spi_pump_messages()
spi: Compatibility with direction which is used in samsung DMA operation
spi-topcliff-pch: add recovery processing in case wait-event timeout
spi-topcliff-pch: supports a spi mode setup and bit order setup by IO control
spi-topcliff-pch: Fix issue for transmitting over 4KByte
spi-topcliff-pch: Modify pci-bus number dynamically to get DMA device info
spi/imx: simplify error handling to free gpios
spi: Convert to DEFINE_PCI_DEVICE_TABLE
spi: add Broadcom BCM63xx SPI controller driver
SPI: add CSR SiRFprimaII SPI controller driver
spi-topcliff-pch: fix -Wuninitialized warning
spi: Mark spi_register_board_info() __devinit
...
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
