Rearrange the config files for remoteproc and IPA to fix their
interdependencies.
First, have CONFIG_QCOM_Q6V5_MSS select QCOM_Q6V5_IPA_NOTIFY so the
notification code is built regardless of whether IPA needs it.
Next, represent QCOM_IPA as being dependent on QCOM_Q6V5_MSS rather
than setting its value to match QCOM_Q6V5_COMMON (which is selected
by QCOM_Q6V5_MSS).
Drop all dependencies from QCOM_Q6V5_IPA_NOTIFY. The notification
code will be built whenever QCOM_Q6V5_MSS is set, and it has no other
dependencies.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set up a subdev in the q6v5 modem remoteproc driver that generates
event notifications for the IPA driver to use for initialization and
recovery following a modem shutdown or crash.
A pair of new functions provides a way for the IPA driver to register
and deregister a notification callback function that will be called
whenever modem events (about to boot, running, about to shut down,
etc.) occur. A void pointer value (provided by the IPA driver at
registration time) and an event type are supplied to the callback
function.
One event, MODEM_REMOVING, is signaled whenever the q6v5 driver is
about to remove the notification subdevice. It requires the IPA
driver de-register its callback.
This sub-device is only used by the modem subsystem (MSS) driver,
so the code that adds the new subdev and allows registration and
deregistration of the notifier is found in "qcom_q6v6_mss.c".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define AXI_GATING_VALID_OVERRIDE and fixup comments to improve readability
of Q6 modem reset sequence on SC7180 SoCs.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200123131236.1078-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Replace the loop for HALT_ACK detection with regmap_read_poll_timeout.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200123131236.1078-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rename the FSM timeout on SC7180 to BOOT_STATUS_TIMEOUT_US.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200117135130.3605-4-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Define CLKEN and CLKOFF for improving readability of Q6SS clock
handling.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200117135130.3605-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct fw_rsc_vdev {
...
struct fw_rsc_vdev_vring vring[0];
} __packed;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(*rsc) + rsc->num_of_vrings * sizeof(struct fw_rsc_vdev_vring)
with:
struct_size(rsc, vring, rsc->num_of_vrings)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190830151406.GA23274@embeddedor
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Provide a basic driver to control Cortex M4 co-processor
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Link: https://lore.kernel.org/r/20191112110330.179649-3-pihsun@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the out of reset sequence support for modem sub-system on SC7180
SoCs. It requires access to an additional halt nav register to put
the modem back into reset.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20191219054506.20565-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently the mem clk is voted upon from both the active and proxy pool on
MSM8998 SoCs where only a proxy vote should suffice. Fix this by removing
mem clk from the active pool.
Fixes: 1665cbd573 ("remoteproc: qcom_q6v5_mss: Add support for MSM8998")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20191218132217.28141-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If the rproc driver is probed before the mailbox driver and if the rproc
Device Tree node has some mailbox properties, the rproc driver probe
shall be deferred instead of being probed without mailbox support.
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Link: https://lore.kernel.org/r/1573812188-19842-1-git-send-email-fabien.dessenne@st.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If the device node defines the 'wakeup-source' property, use the WDG
exti IRQ as a wakeup source of the system.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Link: https://lore.kernel.org/r/1566833923-16718-3-git-send-email-fabien.dessenne@st.com
[bjorn: Replace ifdef with __maybe_unused for suspend/resume functions]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Index of rvring is computed using pointer arithmetic. However, since
rvring->rvdev->vring is the base of the vring array, computation
of rvring idx should be reversed. It previously lead to writing at negative
indices in the resource table.
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20191004073736.8327-1-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The mailbox callback is under interrupt context. A consequence is
that RPMsg Callbacks are also in interrupt context.
Create workqueue to treat the callbacks in normal context.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The rproc_mem_entry_init() call takes a pointer to a vm
as the second argument. The code is currently using a
plain 0 as "NULL". Change to using NULL to fix the
following sparse warnings:
drivers/remoteproc/remoteproc_core.c:339:49: warning: Using plain integer as NULL pointer
drivers/remoteproc/remoteproc_core.c:916:46: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
MSM8998 sits between MSM8996 and SDM845 in terms of functionality needed to
boot the modem subsystem. Booting mss allows for servicing the traditional
cellular usecases along with the wireless usecases such as wifi.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
debugfs_remove_recursive will do NULL check, so remove
the redundant null check
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
rproc_handle_resources_t is not used anymore, remove it.
Signed-off-by: Clement Leger <cleger@kalray.eu>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This exposes the remoteproc's name in sysfs, allows stm32 to enter
platform standby and provides bug fixes for stm32 and Qualcomm's modem
remoteproc drivers. Finally it updates MAINTAINERS to reflect the move
to kernel.org.
-----BEGIN PGP SIGNATURE-----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=T/PI
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This exposes the remoteproc's name in sysfs, allows stm32 to enter
platform standby and provides bug fixes for stm32 and Qualcomm's modem
remoteproc drivers. Finally it updates MAINTAINERS to reflect the move
to kernel.org"
* tag 'rproc-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
MAINTAINERS: remoteproc: update git tree location
remoteproc: Remove dev_err() usage after platform_get_irq()
remoteproc: stm32: manage the get_irq probe defer case
remoteproc: stm32: clear MCU PDDS at firmware start
remoteproc: qcom: q6v5-mss: fixup q6v5_pds_enable error handling
remoteproc: Add a sysfs interface for name
remoteproc: qcom: Move glink_ssr notification after stop
Remoteproc started using dma_declare_coherent_memory recently, which is
a bad idea from drivers, and the maintainers agreed to fix that. But
until that is fixed only allow building the driver built in so that we
can remove the dma_declare_coherent_memory export and prevent other
drivers from "accidentally" using it like remoteproc. Note that the
driver would also leak the declared coherent memory on unload if it
actually was built as a module at the moment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-remoteproc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When remoteproc stops a firmware, it sets the MCU PDDS flag, allowing
the platform to reach the Standby power mode if needed.
Symmetrically, clear this flag before running a firmware.
This fixes the issue where the system goes to Standby mode when the
MCU crashes while MPU is in CSTOP mode.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
dev_pm_domain_attach_by_name will return NULL if the requested
power-domain is not a part device node. This could result in
NULL pointer de-reference in q6v5_pds_enable. Fix this by
checking for IS_ERR_OR_NULL and forward the appropriate error
code.
Fixes: 4760a896be ("remoteproc: q6v5-mss: Vote for rpmh power domains")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds a sysfs interface that provides the name of the
remote processor to userspace. This allows the userspace to identify
a remote processor as the remoteproc devices themselves are created
based on probe order and can change from one boot to another or
at runtime.
The name is made available in debugfs originally, and is being
retained for now. This can be cleaned up after couple of releases
once users get familiar with the new interface.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
glink_ssr is used to signal a remote processor "A" about the stopping of
another remote processor "B", so that in the event that remote processor
B is ever booted again the fifos of the glink channel between A and B is
in a known state.
But if remote processor A receives this notification before B is
actually stopped the newly reset fifo indices will be interpreted as
there being "data" on the channel and either side of the channel will
enter a fatal error handler.
Move the glink_ssr notification to the "unprepare" state of the
rproc_subdev to avoid this issue.
This has the side effect of us not notifying the dying remote processor
itself about its fate, which has been seen to block in certain resource
constraint scenarios.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds support for the STM32 remoteproc, additional i.MX platforms
with Cortex M4 remoteprocs and Qualcomm's QCS404 Compute DSP. Initial
support for vendor specific resource table entries and support for
unprocessed Qualcomm firmware files.
-----BEGIN PGP SIGNATURE-----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=iqXq
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.3' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This adds support for the STM32 remoteproc, additional i.MX platforms
with Cortex M4 remoteprocs and Qualcomm's QCS404 Compute DSP.
Also initial support for vendor specific resource table entries and
support for unprocessed Qualcomm firmware files"
* tag 'rproc-v5.3' of git://github.com/andersson/remoteproc:
remoteproc: stm32: fix building without ARM SMCC
remoteproc: qcom: q6v5-mss: Fix build error without QCOM_MDT_LOADER
remoteproc: copy parent dma_pfn_offset for vdev
remoteproc: qcom: q6v5-mss: Support loading non-split images
soc: qcom: mdt_loader: Support loading non-split images
remoteproc: stm32: add an ST stm32_rproc driver
dt-bindings: remoteproc: add bindings for stm32 remote processor driver
dt-bindings: stm32: add bindings for ML-AHB interconnect
remoteproc: Use struct_size() helper
remoteproc: add vendor resources handling
remoteproc: imx: Fix typo in "failed"
remoteproc: imx: Broaden the Kconfig selection logic
remoteproc,rpmsg: add missing MAINTAINERS file entries
remoteproc: qcom: qdsp6-adsp: Add support for QCS404 CDSP
dt-bindings: remoteproc: Rename and amend Hexagon v56 binding
When compile testing this driver without SMCC support enabled,
we get a link error:
drivers/remoteproc/stm32_rproc.o: In function `stm32_rproc_start':
stm32_rproc.c:(.text+0x776): undefined reference to `__arm_smccc_smc'
drivers/remoteproc/stm32_rproc.o: In function `stm32_rproc_stop':
stm32_rproc.c:(.text+0x92c): undefined reference to `__arm_smccc_smc'
Make the actual call to arm_smccc_smc conditional on the Kconfig
symbol controlling its implementation.
Fixes: 13140de09c ("remoteproc: stm32: add an ST stm32_rproc driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If QCOM_Q6V5_MSS is set but QCOM_MDT_LOADER is not,
building will fails:
drivers/remoteproc/qcom_q6v5_mss.o: In function `q6v5_start':
qcom_q6v5_mss.c:(.text+0x3260): undefined reference to `qcom_mdt_read_metadata'
Add QCOM_MDT_LOADER dependency for QCOM_Q6V5_MSS.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: f04b913834 ("remoteproc: qcom: q6v5-mss: Support loading non-split images")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When preparing the subdevice for the vdev, also copy dma_pfn_offset
since this is used for sub device dma allocations. Without that, there
is incoherency between the parent dma settings and the childs one,
potentially leading to dma_alloc_coherent failure (due to phys_to_dma
using dma_pfn_offset for translation).
Fixes: 086d08725d ("remoteproc: create vdev subdevice with specific dma memory pool")
Signed-off-by: Clement Leger <cleger@kalray.eu>
Acked-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In some software releases the firmware images are not split up with each
loadable segment in it's own file. Check the size of the loaded firmware
to see if it still contains each segment to be loaded, before falling
back to the split-out segments.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch introduces a new remoteproc driver to control Cortex-M4
co-processor of the STM32 family.
It provides with the following features:
- start and stop
- dedicated co-processor memory regions registration
- coredump and recovery
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
[bjorn: Fixup of dev_dbg types and cast of int to pointer in mbox send]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct resource_table {
...
u32 offset[0];
} __packed;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
table->num * sizeof(table->offset[0]) + sizeof(struct resource_table)
with:
struct_size(table, offset, table->num)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to allow rproc backend to handle vendor resources such as in
OpenAMP, add a handle_rsc hook. This hook allow the rproc backends to
handle vendor resources as they like. The hook will be called only for
vendor resources and should return RSC_HANDLED on successful resource
handling, RSC_IGNORED if resource was ignored, or a negative value on
error.
Signed-off-by: Clement Leger <cleger@kalray.eu>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several places where "failed" is spelled incorrectly.
Fix them all.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Besides i.MX6SX and i.MX7D, there are other i.MX devices that contain
Cortex M4 and could make use of the imx remoteproc driver, such as
i.MX7ULP, i.MX8M, etc.
Instead of adding new SoC entries in the Kconfig logic, make it
broader by using the more generic ARCH_MXC, which encompasses
all the 32-bit and 64-bit i.MX devices.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the clock list to adsp_pil_data, make the pdc_reset optional and
make the driver directly enable the xo, sleep and core clocks.
The three clocks are previously toggled through the clock controller,
but that means the same hardware block needs to be mapped in both
drivers. Making the remoteproc driver enable the clocks is a nop when
using the clock controller, but allow us to remove the clocks from the
clock controller.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
