The initial use of this will be to check a flag reporting if an FLR was
performed on other functions when enabling cascaded multicast filters.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GET_WORKAROUNDS was only introduced in May 2014, not all firmware
will have it. So call sites need to handle ENOSYS.
In this case we're probing the bug26807 workaround, which is not
implemented in any firmware that doesn't have GET_WORKAROUNDS.
So interpret ENOSYS as 'false'.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As many issues are encountered at probe time, where MCDI logging can't be
enabled through the sysfs node, this change adds a module parameter
'mcdi_logging_default', which defaults to false. When set to true, newly-
probed functions will have MCDI logging enabled. The setting can
subsequently be changed as normal through the sysfs node.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCDI tracing is enabled per-function with a sysfs file
/sys/class/net/<NET_DEV>/device/mcdi_logging
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCDI tracing is conditional on CONFIG_SFC_MCDI_LOGGING, which is enabled
by default.
Each MCDI command will produce a console line like
sfc dom🚌dev:fn ifname: MCDI RPC REQ: xxxxxxxx [yyyyyyyy...]
where xxxxxxxx etc. are the raw MCDI payload in 32-bit hex chunks.
The response will then produce a similar line with "RESP" instead of "REQ",
and containing the MCDI response payload (if any).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we do an entity reset when we detect an MC reboot.
This messes up SRIOV because it leaves VFs orphaned. The extra
reset is rather redundant anyway, since the MC reboot will have
basically reset everything.
This change replaces the entity reset after MC reboot with a
simpler datapath reset that reallocates resources but doesn't
perform the entity reset.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid MC bugs the flags field needs to be set to 0.
Instead of explicitly clearing out the flags individually, a
better way to do this is to memset the MCDI_BUF to 0.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device ID of the VF to the PCI device ID table.
Added a boolean flag is_vf in efx_nic_type to differentiate
between a VF and PF at probe time. This flag is useful in later
patches while setting MAC address specially in the
PCI-passthrough case.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Accept EPERM in some simple cases, the following cases are handled:
1) efx_mcdi_read_assertion()
Unprivileged PCI functions aren't allowed to GET_ASSERTS.
We return success as it's up to the primary PF to deal with asserts.
2) efx_mcdi_mon_probe() in efx_ef10_probe()
Unprivileged PCI functions aren't allowed to read sensor info, and
worrying about sensor data is the primary PF's job.
3) phy_op->reconfigure() in efx_init_port() and efx_reset_up()
Unprivileged functions aren't allowed to MC_CMD_SET_LINK, they just have
to accept the settings (including flow-control, which is what
efx_init_port() is worried about) they've been given.
4) Fallback to GET_WORKAROUNDS in efx_ef10_probe()
Unprivileged PCI functions aren't allowed to set workarounds. So if
efx_mcdi_set_workaround() fails EPERM, use efx_mcdi_get_workarounds()
to find out if workaround_35388 is enabled.
5) If DRV_ATTACH gets EPERM, try without specifying fw-variant
Unprivileged PCI functions have to use a FIRMWARE_ID of 0xffffffff
(MC_CMD_FW_DONT_CARE).
6) Don't try to exit_assertion unless one had fired
Previously we called efx_mcdi_exit_assertion even if
efx_mcdi_read_assertion had received MC_CMD_GET_ASSERTS_FLAGS_NO_FAILS.
This is unnecessary, and the resulting MC_CMD_REBOOT, even if the
AFTER_ASSERTION flag made it a no-op, would fail EPERM for unprivileged
PCI functions.
So make efx_mcdi_read_assertion return whether an assert happened, and only
call efx_mcdi_exit_assertion if it has.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The (future) code to add/remove vswitches and vports will be
dependent on the firmware variant.
To simplify the checking of the firmware variant, record
values for rx_dpcpu_fw_id and tx_dpcpu_fw_id in EF10 nic_data.
There was only one place where this was previously used:
efx_mcdi_print_fwver() in ethtool.c.
The MC_CMD_GET_CAPABILITIES can be replaced and the values from
nic_data used instead.
Note that the printing of "?" if the MC command fails or if the
outlength is incorrect no longer apply, because errors are returned
in efx_ef10_init_datapath_caps() in both of these cases.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By putting all the efx_{siena,ef10}_sriov_* declarations in
{siena,ef10}_sriov.h, ensure they cannot be called from nic-generic code.
Also fixes up an instance of this, where mcdi.c was calling
efx_siena_sriov_flr.
The single instance of netdev_ops should call general high level
functions that can then call something adapter specific in efx_nic_type.
We should only do adapter specialisation via efx_nic_type.
Removal of sriov functionality from the Falcon code means that tests
are needed for the presence of some callbacks.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch in preparation for the upcoming EF10 sriov support.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MCDI command times out (whether or not we find it
completed when we poll), call efx_mcdi_abandon(), which tells
all subsequent MCDI calls to fail-fast, and queues up an FLR.
Because an FLR doesn't lead to receiving any reboot even from
the MC (unlike most other types of reset), we have to call
efx_ef10_reset_mc_allocations.
In efx_start_all(), if a reset (of any kind) is pending, we
bail out.
Without this, attempts to reconfigure (e.g. change mtu) can
cause driver/mc state inconsistency if the first MCDI call
triggers an FLR.
For similar reasons, on EF10, in
efx_reset_down(method=RESET_TYPE_MCDI_TIMEOUT), set the number
of active queues to zero before calling efx_stop_all().
And, on farch, in efx_reset_up(method=RESET_TYPE_MCDI_TIMEOUT),
set active_queues and flushes pending & outstanding to zero.
efx_mcdi_mode_{poll,event}() should not take us out of fail-fast
mode. Instead, this is done by efx_mcdi_reset() after the FLR
completes.
The new FLR reset_type RESET_TYPE_MCDI_TIMEOUT doesn't really
fit into the hierarchy of reset 'scopes' whereby efx_reset()
decides some resets subsume others. Thus, it uses separate logic.
Also, fixed up some inconsistency around RESET_TYPE_MC_BIST,
which was in the wrong place in that hierarchy.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Faster than memcpy/memset on some architectures.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PORT_RESET MC command was NOP in the ef10 firmware hence we are using
ENTITY_RESET to make sure all resource allocations are reset.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The primary function of an EF10 controller will share its clock
device with other functions in the same domain (which we call
secondary functions). To this end, we need to associate functions
on the same controller.
We do not control probe order, so allow primary and secondary
functions to appear in any order. Maintain global lists of all
primary functions and of unassociated secondary functions,
and a list of secondary functions on each primary function.
Use the VPD serial number to tell whether functions are part of the
same controller. VPD will not be readable by virtual functions, so
this may need to be revisited later.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The EF10 firmware can optionally insert RX timestamps in the packet
prefix. These only include the clock minor value. We must also
enable periodic time sync events on each event queue which provide
the high bits of the clock value.
[bwh: Combined and rebased several changes.
Added the above description and some sanity checks for inline vs
separate timestamps.
Changed efx_rx_skb_attach_timestamp() to read the packet prefix
from the skb head area.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Split each of efx_mcdi_rpc, efx_mcdi_rpc_finish, and efx_mcdi_rpc_async into
a normal and a _quiet version; made the former log MCDI errors with
netif_err (and include the raw MCDI error code), and the latter never log
them at all. Changed various callers; any where some errors are expected
(but others are not) call the _quiet version and then if necessary log the
MCDI error themselves. Said logging is done by new efx_mcdi_display_error.
Callers of efx_mcdi_rpc*_quiet functions which may want to log the error
need to ensure that their outbuf is big enough to hold an MCDI error; to
this end, they now use MCDI_DECLARE_BUF_OUT_OR_ERR, which always allocates
at least 8 bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
To run BISTs the MC goes down in to a special mode where it will only
respond to MCDI from the testing PF, and TX, RX and event queues are
torn down. Other PFs get a message as it goes down to tell them it's
going down.
When the other PFs get this message, they check the soft status
register to tell when the MC has rebooted after BIST mode and they can
start recovery.
[bwh: Convert the test result to 1 or -1 as for earlier NICs]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The MC firmware is cooperatively multitasking and its scheduler will
send an event when a task yields after running for more than the
expected maximum time. This can be useful for firmware development
but does not usually indicate a serious error and does not help to
detect a lockup (there is a hardware watchdog that does that).
Change the message and reduce log level accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
There is an as-yet unexplained bug that sometimes prevents (or delays)
the driver seeing the completion event for a completed MCDI request on
the SFC9120. The requested configuration change will have happened
but the driver assumes it to have failed, and this can result in
further failures. We can mitigate this by polling for completion
after unsuccessfully waiting for an event.
Fixes: 8127d661e7 ('sfc: Add support for Solarflare SFC9100 family')
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Although we do not yet enable multiple PFs per port, it is possible
that a board will be reconfigured to enable them while the driver has
not yet been updated to fully support this.
The most obvious problem is that multiple functions may try to set
conflicting link settings. But we will also run into trouble if the
firmware doesn't consider us fully trusted. So, abort probing unless
both the LinkCtrl and Trusted flags are set for this function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The SFC9120 MC firmware often takes longer than 20ms to reboot and
update the warm boot count in BIU_MC_SFT_STATUS_REG. A timeout of
250ms is very generous for an MC reboot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Scheduling a reset following an MC reboot event before waiting for
reboot to complete results in a race that can lead to a state where
must_realloc_vis is false in efx_ef10_fini_dmaq() but the VIs have
been destroyed during the MC reboot.
To avoid MC errors when trying to remove VIs that do not exist, wait
for the MC reboot to complete before scheduling the reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Update the dates for files that have been added to in 2012-2013.
Drop the 'Solarstorm' brand name that's still lingering here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This adds support for the EF10 network controller architecture and the
SFC9100 family, starting with SFC9120 'Farmingdale', and bumps the
driver version to 4.0.
New features in the SFC9100 family include:
- Flexible allocation of internal resources to PCIe physical and virtual
functions under firmware control
- RX event merging to reduce DMA writes at high packet rates
- Integrated RX timestamping
- PIO buffers for lower TX latency
- Firmware-driven data path that supports additional offload features
and filter types
- Delivery of packets between functions and to multiple recipients,
allowing firmware to implement a vswitch
- Multiple RX flow hash (RSS) contexts with their own hash keys and
indirection tables
- 40G MAC (single port only)
...not all of which are enabled in this initial driver or the initial
firmware release.
Much of the new code is by Jon Cooper.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We can set, get and compare-and-exchange without using atomic_t.
Change efx_mcdi_iface::state to the enum type we really wanted it to
be.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The Huntington MC will reject all MCDI requests after an MC reboot until it sees
one with the NOT_EPOCH flag clear. This flag is set by default for all requests,
and then cleared on the first request after we detect that an MC reboot has
occurred.
The old MCDI_STATUS_DELAY_COUNT gave a timeout of 10ms, which was not long enough
for the driver to detect that a reboot had occurred based on the warm boot count
while calling efx_mcdi_poll_reboot() from the loop in efx_mcdi_ev_death().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Also, since we handle all DMA errors in the same way, merge
RESET_TYPE_(RX|TX)_DESC_FETCH into RESET_TYPE_DMA_ERROR.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Various hardware statistics that are available for Siena are
unavailable or meaningless for Falcon. Huntington adds further to the
NIC-type-specific statistics, as it has different MAC blocks from
Falcon/Siena.
All NIC types still provide most statistics by DMA, and use
little-endian byte order.
Therefore:
1. Add some general utility functions for reporting hardware statistics,
efx_nic_describe_stats() and efx_nic_update_stats().
2. Add an efx_nic_type::describe_stats operation to get the number and
names of statistics, implemented using efx_nic_describe_stats()
3. Change efx_nic_type::update_stats to store the core statistics
(struct rtnl_link_stats64) or full statistics (array of u64) in a
caller-provided buffer. Use efx_nic_update_stats() to aid in the
implementation.
4. Rename struct efx_ethtool_stat to struct efx_sw_stat_desc and
EFX_ETHTOOL_NUM_STATS to EFX_ETHTOOL_SW_STAT_COUNT.
5. Remove efx_nic::mac_stats and struct efx_mac_stats.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Merge the per-NIC-type MTD probe selection and struct efx_mtd_ops into
struct efx_nic_type. Move the implementations into the appropriate
source files.
Several NVRAM functions are now only called from MTD operations which
are now implemented in the same file (falcon.c or mcdi.c). There is no
need for them to be extern, or to be defined at all if CONFIG_SFC_MTD
is not enabled, so move them into the #ifdef CONFIG_SFC_MTD sections
in those files.
Most of the SPI-related definitions are also only used in falcon.c,
so move them there. Put the remainder of spi.h into nic.h (which
previously included it).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
When we poll for MCDI request completion, we don't hold the interface
lock while setting the response fields in struct efx_mcdi_iface.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MCDI v2 adds a second header dword with wider command and length
fields. It also defines extra error codes.
Change the fallback error number for unknown MCDI error codes from EIO
to EPROTO. EIO is treated as indicating the MCDI transport has failed
and we need to reset the function, which is rather drastic.
v2 error codes and lengths don't fit into completion events, so for a
v2-capable transport, always read the response header rather then
using the event fields.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
EF10 controllers do not have shared memory for communication with the
MC; instead it reads requests and writes responses in host memory,
which allows for longer messages. It is also responsible for all
datapath control operations and hardware resource allocation, which
requires a large number of new commands and adds more possible error
cases. MCDI v2 extends the message header to support this.
Update the MCDI protocol definition header to include v2 lengths,
errors and messages, and a few definitions specific to the
SFC9100 family (codenames Farmingdale and Huntington) which is
the first generation of EF10.
Some messages have been extended, so adjust the code accordingly:
- The request for MC_CMD_DRV_ATTACH now includes a datapath firmware
ID. This is ignored by Siena but we should fill it in anyway,
initially always specifying low-latency datapath.
- The response for MC_CMD_GET_LOOPBACK_MODES now includes a 40G
field. Accept shorter responses that don't include it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently we only translate error codes in efx_mcdi_poll(), but we
also need to do so in efx_mcdi_ev_cpl().
The reason we didn't notice before is that the MC firmware error codes
are mostly taken from Unix/Linux and no translation is necessary on
most architectures. Make sure we notice any future failure by
changing the sign of resprc (matching the kernel convention) and BUG
if it's ever positive at command completion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The EF10 architecture has a very different register layout from
previous controllers, so we'll use separate files for the two sets of
register definitions. Use 'farch' as an abbreviation for
Falcon-architecture.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move the lowest layer (transport) of the current MCDI code to
per-NIC-type operations.
Introduce a new structure and efx_nic member for MCDI-specific data.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This should probably be done during MCDI initialisation for any NIC.
Change efx_mcdi_init() to return an error code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Collect together MCDI port functions from mcdi.c, mcdi_mac.c,
mcdi_phy.c and siena.c. Rename the 'siena' functions accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We currently require that MCDI request and response lengths are
multiples of 4 bytes, because we will copy dwords in and out of shared
memory and we want to be sure we won't read or write out of bounds.
But all we really need to know is that there is sufficient padding for
that. Also, we should ensure that buffers are dword-aligned, as on
some architectures misaligned access will result in data corruption or
a crash.
Change the buffer type to array-of-efx_dword_t and remove the
requirement that the lengths are multiples of 4.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
A few functions are using heap buffers; change them to use stack
buffers as we really don't need to resort to the heap for a 252
byte buffer in process context.
MC_CMD_MEMCPY is quite weird in that it can use inline data placed in
the request buffer after the array of records. Thus there are two
variable-length arrays and we can't use the normal accessors for
the second. So we have to use _MCDI_PTR() in efx_sriov_memcpy().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MCDI_DECLARE_BUF declares a variable as an MCDI buffer of the
requested length, adding any necessary padding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_mcdi_get_board_cfg() uses a buffer for the firmware response that
is only large enough to hold subtypes for the originally defined set
of NVRAM partitions. Longer responses are truncated, and we may read
off the end of the buffer when copying out subtypes for additional
partitions. In particular, this can result in the MTD partition for
an FPGA bitfile being named e.g. 'eth5 sfc_fpga:00' when it should be
'eth5 sfc_fpga:01'. This means the firmware update tool (sfupdate)
can't tell which bitfile should be written to the partition.
Correct the response buffer size.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
