Changing framerate right before streamon had no effect,
the new framerate value was taken into account only at
next streamon, fix this.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media
bus enum.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Change 720p JPEG mode to mode 3 as per other resolutions.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mode setting depends on last mode set, in particular
because of exposure calculation when downscale mode
change between subsampling and scaling.
At stream on the last mode was wrongly set to current mode,
so no change was detected and exposure calculation
was not made, fix this.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When switching from auto to manual mode, V4L2 core is calling
g_volatile_ctrl() in manual mode in order to get the manual initial value.
Remove the manual mode check/return to not break this behaviour.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ov5640_set_mode_exposure_calc() is checking binning value but
binning value read is buggy, fix this.
Rename ov5640_binning_on() to ov5640_get_binning() as per other
similar functions.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Ensure that auto gain and auto exposure are well restored
when changing mode.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Symptom was black image when capturing HD or 5Mp picture
due to manual exposure set to 1 while it was intended to
set autoexposure to "manual", fix this.
Fixes: bf4a4b518c ("media: ov5640: Don't force the auto exposure state at start time").
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As of: commit 476dec012f ("media: ov5640: Add horizontal and vertical
totals") the timings parameters gets programmed separately from the
static register values array.
When changing capture mode, the vertical and horizontal totals gets
inspected by the set_mode_exposure_calc() functions, and only later
programmed with the new values. This means exposure, light banding
filter and shutter gain are calculated using the previous timings, and
are thus not correct.
Fix this by programming timings right after the static register value
table has been sent to the sensor in the ov5640_load_regs() function.
Fixes: 476dec012f ("media: ov5640: Add horizontal and vertical totals")
Tested-by: Steve Longerbeam <slongerbeam@gmail.com> # i.MX6q SabreSD, CSI-2
Tested-by: Loic Poulain <loic.poulain@linaro.org> # Dragonboard-410c, CSI-2
Signed-off-by: Samuel Bobrowicz <sam@elite-embedded.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rework the MIPI interface startup sequence with the following changes:
- Remove MIPI bus initialization from the initial settings blob
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At s_stream time enable/disable the MIPI interface output.
- Restore default settings at set_power(0) time.
Before this commit the sensor MIPI interface was initialized with settings
that require a start/stop sequence at power-up time in order to force lanes
into LP11 state, as they were initialized in LP00 when in 'sleep mode',
which is assumed to be the sensor manual definition for the D-PHY defined
stop mode.
The stream start/stop was performed by enabling disabling clock gating,
and had the side effect to change the lanes sleep mode configuration when
stream was stopped.
Clock gating/ungating:
- ret = ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
- on ? 0 : BIT(5));
- if (ret)
Set lanes in LP11 when in 'sleep mode':
- ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
- on ? 0x00 : 0x70);
This commit fixes an issue reported by Jagan Teki on i.MX6 platforms that
prevents the host interface from powering up correctly:
https://lkml.org/lkml/2018/6/1/38
It also improves MIPI capture operations stability on my testing platform
where MIPI capture often failed and returned all-purple frames.
Fixes: f22996db44 ("media: ov5640: add support of DVP parallel interface")
Tested-by: Steve Longerbeam <slongerbeam@gmail.com> (i.MX6q SabreSD, CSI-2)
Tested-by: Loic Poulain <loic.poulain@linaro.org> (Dragonboard-410c, CSI-2)
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
fixes: 6949d86477 ("media: ov5640: do not change mode if format or frame interval is unchanged").
Symptom was fuzzy image because of JPEG default format
not being changed according to new format selected, fix this.
Init sequence initialises format to YUV422 UYVY but
sensor->fmt initial value was set to JPEG, fix this.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Save load of mode registers array when V4L2 client sets a format or a
frame interval which selects the same mode than the current one.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Driver must reject frame interval enumeration of unsupported resolution.
This was detected by v4l2-compliance format ioctl test:
v4l2-compliance Format ioctls:
info: found 2 frameintervals for pixel format 4745504a and size 176x144
fail: v4l2-test-formats.cpp(123):
found frame intervals for invalid size 177x144
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
According to ov5640 datasheet xvclk is allowed to be between 6 and 54 MHz.
I run a successful test with 27 MHz.
Signed-off-by: Philipp Puschmann <pp@emlix.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support of module being physically mounted upside down.
In this case, mirror and flip are enabled to fix captured images
orientation.
[Sakari Ailus: Use dev_fwnode() instead of accessing device's of_node]
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add HFLIP/VFLIP controls support by setting registers REG21/REG20.
Useless values in hardcoded mode sequences are removed and
remaining binning values are now set after mode sequence being set.
Note that due to BSI (Back Side Illuminated) technology, image capture
is physically mirrored, mirror logic is so inversed in REG21 register
to cancel this effect.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The active frame size is set in the initialization arrays, but the value
itself is also available in the struct ov5640_mode_info.
Let's move these values out of the big bytes arrays, and program it with
the value of the mode that we are given.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All the initialization arrays are changing the horizontal and vertical
totals for some value.
In order to clean up the driver, and since we're going to need that value
later on, let's introduce in the ov5640_mode_info structure the horizontal
and vertical total sizes, and move these out of the bytes array.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The current width and height parameters in the struct ov5640_mode_info are
actually the active horizontal and vertical resolutions.
Since we're going to add a few other parameters, let's pick a better, more
precise name for these values.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SCLK and SCLK2X dividers are fixed in stone in the initialization
array. Let's make explicit what we're doing and move that away from the
huge array to the initialization code.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sensor needs to have the auto exposure stopped while changing mode.
However, when the new mode is set, the driver will force the auto exposure
on, disregarding whether the control has been changed or not.
Bypass the controls code entirely to do that, and only use the control
value cached when restoring the auto exposure mode.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the light frequency control to be able to set the frequency
to manual (50Hz or 60Hz) or auto.
[Sakari Ailus: Rename "ctl" as "ctrl" as agreed.]
[mchehab+samsung@kernel.org: fixed two coding style warnings]
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use dev_fwnode() on the device instead of getting an fwnode handle of the
device's OF node. The result is the same on OF-based systems and looks
better, too.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The output pixel format changed by set_fmt() pad operation is not
correctly applied. It is intended to be restored by calling
ov5640_set_framefmt() when the video stream is started.
However, when the device is powered on by s_power subdev operation before
the video stream is started, the current output mode setting is restored
by ov5640_restore_mode() that also clears pending_mode_change flag in
ov5640_set_mode(). So ov5640_set_framefmt() isn't called as intended and
the output pixel format is not restored.
This change adds the missing output pixel format setting in the
ov5640_restore_mode() that is called when the device is powered on.
Cc: Steve Longerbeam <slongerbeam@gmail.com>
Cc: Hugues Fruchet <hugues.fruchet@st.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix set of missing colorspace related fields in get_/set_fmt.
Detected by v4l2-compliance tool.
[Sakari Ailus: Rearrange fmt declaration in ov5640_probe()]
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
After a framerate update through s_frame_interval(), the new
framerate was not taken into account when streaming,
but was taken into account on next session.
This was due to sensor->current_mode not updated accordingly to new
framerate setting in ov5640_s_frame_interval().
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix module_param(virtual_channel) permissions.
This problem was detected by checkpatch:
$ scripts/checkpatch.pl -f drivers/media/i2c/ov5640.c
ERROR: Use 4 digit octal (0777) not decimal permissions
+module_param(virtual_channel, int, 0);
Also add an error trace in case of virtual_channel not in
the valid range of values.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Various typo & style fixes either detected by code
review or checkpatch.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add an error trace in ov5640_read_reg() in case of i2c_transfer()
failure.
Uniformize error traces using dev_err instead v4l2_err.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Time to time, stream on is failing with a strange positive error.
Error code is returned erroneously by ov5640_set_ctrl_exposure()
due to ov5640_get_vts() return value wrongly treated as error.
Fix this by forcing ret to 0 after ov5640_get_vts() success call,
in order that ret is set to success for rest of code sequence.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support of DVP parallel mode in addition of
existing MIPI CSI mode. The choice between two modes
and configuration is made through device tree.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver is based on ov5640_mipi.c from Freescale imx_3.10.17_1.0.0_beta
branch, modified heavily to bring forward to latest interfaces and code
cleanup.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
