The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_aborted_errors statistic should count packets flagged with EXD,
EXC, FU, or BCM bits because those bits denote an aborted transmission.
That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these
constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as
there's a separate counter for that purpose.
Don't lump all these errors in with the general tx_errors counter as
that's used for tx timeout events.
On the rx side, don't count RDE and RBAE interrupts as dropped packets.
These interrupts don't indicate a lost packet, just a lack of resources.
When a lack of resources results in a lost packet, this gets reported
in the rx_missed_errors counter (along with RFO events).
Don't double-count rx_frame_errors and rx_crc_errors.
Don't use the general rx_errors counter for events that already have
special counters.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip can change a packet's descriptor status flags at any time.
However, an active interrupt flag gets cleared rather late. This
allows a race condition that could theoretically lose an interrupt.
Fix this by clearing asserted interrupt flags immediately.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy says:
====================
Add PHY IDs for DP83825/6
Adding new PHY IDs for the DP83825 and DP83826 TI Ethernet PHYs to the DP83822
PHY driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PHY IDs for the DP83825CS, DP83825CM and the DP83825S devices to the
DP83822 driver.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phy IDs to the DP83822 phy driver for the DP83826N
and the DP83826NC devices. The register map and features
are the same for basic enablement.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the only 10G PHY interface type defined at the moment the code
was developed was XGMII, although the PHY interface mode used was
not XGMII, XGMII was used in the code to denote 10G. This patch
renames the 10G interface mode to remove the ambiguity.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur says:
====================
net: fsl/fman: address erratum A011043
This addresses a HW erratum on some QorIQ DPAA devices.
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
When the issue was present, one could see such errors
during boot:
mdio_bus ffe4e5000: Error while reading PHY0 reg at 3.3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When fsl,erratum-a011043 is set, adjust for erratum A011043:
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fsl,erratum-a011043 to internal MDIO buses.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for erratum A011043: the MDIO_CFG[MDIO_RD_ER]
bit may be falsely set when reading internal PCS registers.
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver while collecting firmware dump takes longer time to
collect/process some of the firmware dump entries/memories.
Bigger capture masks makes it worse as it results in larger
amount of data being collected and results in CPU soft lockup.
Place cond_resched() in some of the driver flows that are
expectedly time consuming to relinquish the CPU to avoid CPU
soft lockup panic.
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Tested-by: Yonggen Xu <Yonggen.Xu@dell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Primarily bugfixes, mostly around handling index wrap-around correctly.
A couple of doc fixes and adding missing APIs.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEejHryeLBw/spnjHrDpNsjXcpgj4FAl4pJv4ACgkQDpNsjXcp
gj5OXgf/Q52Am0tLS6iC7XtcojjidnSFzpAqn9OGo7zuTsP+QURsiZAXJpjvUF8y
kGIcD9R/tobEADkyDnj8D64yO+CqT1PlkaYvO5R+nYx/WTtmvr3/O/7Y4/ZTAwcf
tTvj3yXlKbsA+9YJa34t43Ul4EDCOrQTz+oIZUQsiaRNzIdmCCguLg5gOkIhoXt6
wJwp2Fc3YN6McBBpZH2z0GRwdJWPcixtKH0RNhOyGUiWBhkWYFXNvNEdxKJmTXdK
qqkoW9So8IkyyoXdW8ZpQqCCk9tPRv9+7adDFVwl/T8q/RBrHNtcyQqJL3EsScsi
9IqCrKldzRenk0v6lG+mgJEuTvYs8A==
=7cpi
-----END PGP SIGNATURE-----
Merge tag 'xarray-5.5' of git://git.infradead.org/users/willy/linux-dax
Pull XArray fixes from Matthew Wilcox:
"Primarily bugfixes, mostly around handling index wrap-around
correctly.
A couple of doc fixes and adding missing APIs.
I had an oops live on stage at linux.conf.au this year, and it turned
out to be a bug in xas_find() which I can't prove isn't triggerable in
the current codebase. Then in looking for the bug, I spotted two more
bugs.
The bots have had a few days to chew on this with no problems
reported, and it passes the test-suite (which now has more tests to
make sure these problems don't come back)"
* tag 'xarray-5.5' of git://git.infradead.org/users/willy/linux-dax:
XArray: Add xa_for_each_range
XArray: Fix xas_find returning too many entries
XArray: Fix xa_find_after with multi-index entries
XArray: Fix infinite loop with entry at ULONG_MAX
XArray: Add wrappers for nested spinlocks
XArray: Improve documentation of search marks
XArray: Fix xas_pause at ULONG_MAX
- Fix a function comparison warning for a xen trace event macro
- Fix a double perf_event linking to a trace_uprobe_filter for multiple events
- Fix suspicious RCU warnings in trace event code for using
list_for_each_entry_rcu() when the "_rcu" portion wasn't needed.
- Fix a bug in the histogram code when using the same variable
- Fix a NULL pointer dereference when tracefs lockdown enabled and calling
trace_set_default_clock()
This v2 version contains:
- A fix to a bug found with the double perf_event linking patch
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXinakBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qhNZAQCi86p9eW3f3w7hM2hZcirC+mQKVZgp
2rO4zIAK5V6G7gEAh6I7VZa50a6AE647ZjryE7ufTRUhmSFMWoG0kcJ7OAk=
=/J9n
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.5-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Various tracing fixes:
- Fix a function comparison warning for a xen trace event macro
- Fix a double perf_event linking to a trace_uprobe_filter for
multiple events
- Fix suspicious RCU warnings in trace event code for using
list_for_each_entry_rcu() when the "_rcu" portion wasn't needed.
- Fix a bug in the histogram code when using the same variable
- Fix a NULL pointer dereference when tracefs lockdown enabled and
calling trace_set_default_clock()
- A fix to a bug found with the double perf_event linking patch"
* tag 'trace-v5.5-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/uprobe: Fix to make trace_uprobe_filter alignment safe
tracing: Do not set trace clock if tracefs lockdown is in effect
tracing: Fix histogram code when expression has same var as value
tracing: trigger: Replace unneeded RCU-list traversals
tracing/uprobe: Fix double perf_event linking on multiprobe uprobe
tracing: xen: Ordered comparison of function pointers
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAl4p1+MTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi4YtCACPHyE8aoDTHZF8UZ9bHKNFVt4C1bRx
ihFB6/PzmIfFw4Cbf+yTW85q3zqJ/6eJIOZF4dlwoFWK+osSk8sYRaOvlEovysbR
sYiAbcOxePj9tSPdrWLYB/5ELtwMTloxBo7mPiJYt127UntWlPGfiz4sdHJBt1zI
IBPOIeACJKGe0+Wtj0mGsXk+WhEB3nFk2DINnLuFc4tG6yXkFNq5/fnXrgVTlUTF
4EwDQgHBUIqKDJarSyIBzud6VVshS7VaMAu8h9kwPScN4sG1y4ucgFzXIc4JfqRN
TnEV48hdRQMVuQtsvuzAMPQvsjMlIXUSTGZzs4XPbEBjgAP8+MP+PJvL
=XVg1
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.5-rc8' of https://github.com/ceph/ceph-client
Pull ceph fix from Ilya Dryomov:
"A fix for a potential use-after-free from Jeff, marked for stable"
* tag 'ceph-for-5.5-rc8' of https://github.com/ceph/ceph-client:
ceph: hold extra reference to r_parent over life of request
Prevent the kernel from crashing during resume from hibernation
if free pages contain leftover data from the restore kernel and
init_on_free is set (Alexander Potapenko).
-----BEGIN PGP SIGNATURE-----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=kDFG
-----END PGP SIGNATURE-----
Merge tag 'pm-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Prevent the kernel from crashing during resume from hibernation if
free pages contain leftover data from the restore kernel and
init_on_free is set (Alexander Potapenko)"
* tag 'pm-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: hibernate: fix crashes with init_on_free=1
In commit 9f79b78ef7 ("Convert filldir[64]() from __put_user() to
unsafe_put_user()") I changed filldir to not do individual __put_user()
accesses, but instead use unsafe_put_user() surrounded by the proper
user_access_begin/end() pair.
That make them enormously faster on modern x86, where the STAC/CLAC
games make individual user accesses fairly heavy-weight.
However, the user_access_begin() range was not really the exact right
one, since filldir() has the unfortunate problem that it needs to not
only fill out the new directory entry, it also needs to fix up the
previous one to contain the proper file offset.
It's unfortunate, but the "d_off" field in "struct dirent" is _not_ the
file offset of the directory entry itself - it's the offset of the next
one. So we end up backfilling the offset in the previous entry as we
walk along.
But since x86 didn't really care about the exact range, and used to be
the only architecture that did anything fancy in user_access_begin() to
begin with, the filldir[64]() changes did something lazy, and even
commented on it:
/*
* Note! This range-checks 'previous' (which may be NULL).
* The real range was checked in getdents
*/
if (!user_access_begin(dirent, sizeof(*dirent)))
goto efault;
and it all worked fine.
But now 32-bit ppc is starting to also implement user_access_begin(),
and the fact that we faked the range to only be the (possibly not even
valid) previous directory entry becomes a problem, because ppc32 will
actually be using the range that is passed in for more than just "check
that it's user space".
This is a complete rewrite of Christophe's original patch.
By saving off the record length of the previous entry instead of a
pointer to it in the filldir data structures, we can simplify the range
check and the writing of the previous entry d_off field. No need for
any conditionals in the user accesses themselves, although we retain the
conditional EINTR checking for the "was this the first directory entry"
signal handling latency logic.
Fixes: 9f79b78ef7 ("Convert filldir[64]() from __put_user() to unsafe_put_user()")
Link: https://lore.kernel.org/lkml/a02d3426f93f7eb04960a4d9140902d278cab0bb.1579697910.git.christophe.leroy@c-s.fr/
Link: https://lore.kernel.org/lkml/408c90c4068b00ea8f1c41cca45b84ec23d4946b.1579783936.git.christophe.leroy@c-s.fr/
Reported-and-tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 8a23eb804c ("Make filldir[64]() verify the directory entry
filename is valid") added some minimal validity checks on the directory
entries passed to filldir[64](). But they really were pretty minimal.
This fleshes out at least the name length check: we used to disallow
zero-length names, but really, negative lengths or oevr-long names
aren't ok either. Both could happen if there is some filesystem
corruption going on.
Now, most filesystems tend to use just an "unsigned char" or similar for
the length of a directory entry name, so even with a corrupt filesystem
you should never see anything odd like that. But since we then use the
name length to create the directory entry record length, let's make sure
it actually is half-way sensible.
Note how POSIX states that the size of a path component is limited by
NAME_MAX, but we actually use PATH_MAX for the check here. That's
because while NAME_MAX is generally the correct maximum name length
(it's 255, for the same old "name length is usually just a byte on
disk"), there's nothing in the VFS layer that really cares.
So the real limitation at a VFS layer is the total pathname length you
can pass as a filename: PATH_MAX.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Should work properly with the latest sbios on 5.5 and newer
kernels.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set d0 and d1 pin directions for spi0 and spi1 as per their pinmux.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When submitting v2 of "fou: Support binding FoU socket" (1713cb37bf),
I accidentally sent the wrong version of the patch and one fix was
missing. In the initial version of the patch, as well as the version 2
that I submitted, I incorrectly used ".type" for the two V6-attributes.
The correct is to use ".len".
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: 1713cb37bf ("fou: Support binding FoU socket")
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeKX2wAAoJEG4XJFUm622bG8QH/3+QXaSJAVqzbQh2boy7aS88
xhrrnh+bSqWY0ChMk0Z73RF8Ek0WlO+os4uN1cbWIWujrdQUPbTBtOwX4d0TzTue
E3tBFPiHTlVtU43z1bsprA+6EE7fqt/H2lWtlxk0IHzeiQY9NcB6BlDKKCzk5Hib
aMb5HCQy4JmSK83E60HLM9L4nEmEP+yveaKL7uaAZw+qkmyk2mT6um0TlmOYVoNG
9V6k3OZto8LvyV6jKPZgVI6QBATnwHDxlWgooYRj54PuCj9hTbR2mcuUL2QyQeze
AX2QNI+1kWIrAiDaU/lOj8579SiUl36iqtuKmtLhDnSe1GxDkrzmawtz3aGDm4k=
=VZox
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program
consumes the skb, we need to clear the napi.skb (or risk
a use-after-free) and release the mutex (or risk a deadlock)
WARNING: lock held when returning to user space!
5.5.0-rc6-syzkaller #0 Not tainted
------------------------------------------------
syz-executor.0/455 is leaving the kernel with locks still held!
1 lock held by syz-executor.0/455:
#0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Petar Penkov <ppenkov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gautam Ramakrishnan says:
====================
net: sched: add Flow Queue PIE packet scheduler
Flow Queue PIE packet scheduler
This patch series implements the Flow Queue Proportional
Integral controller Enhanced (FQ-PIE) active queue
Management algorithm. It is an enhancement over the PIE
algorithm. It integrates the PIE aqm with a deficit round robin
scheme.
FQ-PIE is implemented over the latest version of PIE which
uses timestamps to calculate queue delay with an additional
option of using average dequeue rate to calculate the queue
delay. This patch also adds a memory limit of all the packets
across all queues to a default value of 32Mb.
- Patch #1
- Creates pie.h and moves all small functions and structures
common to PIE and FQ-PIE here. The functions are all made
inline.
- Patch #2 - #8
- Addresses code formatting, indentation, comment changes
and rearrangement of structure members.
- Patch #9
- Refactors sch_pie.c by changing arguments to
calculate_probability(), [pie_]drop_early() and
pie_process_dequeue() to make it generic enough to
be used by sch_fq_pie.c. These functions are exported
to be used by sch_fq_pie.c.
- Patch #10
- Adds the FQ-PIE Qdisc.
For more information:
https://tools.ietf.org/html/rfc8033
Changes from v6 to v7
- Call tcf_block_put() when destroying the Qdisc as suggested
by Jakub Kicinski.
Changes from v5 to v6
- Rearranged struct members according to their access pattern
and to remove holes.
Changes from v4 to v5
- This patch series breaks down patch 1 of v4 into
separate logical commits as suggested by David Miller.
Changes from v3 to v4
- Used non deprecated version of nla_parse_nested
- Used SZ_32M macro
- Removed an unused variable
- Code cleanup
All suggested by Jakub and Toke.
Changes from v2 to v3
- Exported drop_early, pie_process_dequeue and
calculate_probability functions from sch_pie as
suggested by Stephen Hemminger.
Changes from v1 ( and RFC patch) to v2
- Added timestamp to calculate queue delay as recommended
by Dave Taht
- Packet memory limit implemented as recommended by Toke.
- Added external classifier as recommended by Toke.
- Used NET_XMIT_CN instead of NET_XMIT_DROP as the return
value in the fq_pie_qdisc_enqueue function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Principles:
- Packets are classified on flows.
- This is a Stochastic model (as we use a hash, several flows might
be hashed to the same slot)
- Each flow has a PIE managed queue.
- Flows are linked onto two (Round Robin) lists,
so that new flows have priority on old ones.
- For a given flow, packets are not reordered.
- Drops during enqueue only.
- ECN capability is off by default.
- ECN threshold (if ECN is enabled) is at 10% by default.
- Uses timestamps to calculate queue delay by default.
Usage:
tc qdisc ... fq_pie [ limit PACKETS ] [ flows NUMBER ]
[ target TIME ] [ tupdate TIME ]
[ alpha NUMBER ] [ beta NUMBER ]
[ quantum BYTES ] [ memory_limit BYTES ]
[ ecnprob PERCENTAGE ] [ [no]ecn ]
[ [no]bytemode ] [ [no_]dq_rate_estimator ]
defaults:
limit: 10240 packets, flows: 1024
target: 15 ms, tupdate: 15 ms (in jiffies)
alpha: 1/8, beta : 5/4
quantum: device MTU, memory_limit: 32 Mb
ecnprob: 10%, ecn: off
bytemode: off, dq_rate_estimator: off
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: V. Saicharan <vsaicharan1998@gmail.com>
Signed-off-by: Mohit Bhasi <mohitbhasi1998@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the drop_early(), calculate_probability() and
pie_process_dequeue() functions generic enough to be used by
both PIE and FQ-PIE (to be added in a future commit). The major
change here is in the way the functions take in arguments. This
patch exports these functions and makes FQ-PIE dependent on
sch_pie.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the alignment in the initialization of the struct instances
consistent in the file.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix punctuation and logical mistakes in the comments. The
logical mistake was that "dequeue_rate" is no longer the default
way to calculate queuing delay and is not needed. The default
way to calculate queue delay was changed in commit cec2975f2b
("net: sched: pie: enable timestamp based delay calculation").
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the comments along with the commenting style used to
describe the members of the structures and their initial values
in the init functions.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange the members of the structure such that closely
referenced members appear together and/or fit in the same
cacheline. Also, change the order of their initializations to
match the order in which they appear in the structure.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux best practice recommends using u8 for true/false values in
structures.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange macros in order of length and align the values to
improve readability.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the U64_MAX macro to denote the constant (2^64 - 1).
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves macros, structures and small functions common
to PIE and FQ-PIE (to be added in a future commit) from the file
net/sched/sch_pie.c to the header file include/net/pie.h.
All the moved functions are made inline.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During reload (or module unload), the router block is de-initialized.
Among other things, this results in the removal of a default multicast
route from each active virtual router (VRF). These default routes are
configured during initialization to trap packets to the CPU. In
Spectrum-2, unlike Spectrum-1, multicast routes are implemented using
ACL rules.
Since the router block is de-initialized before the ACL block, it is
possible that the ACL rules corresponding to the default routes are
deleted while being accessed by the ACL delayed work that queries rules'
activity from the device. This can result in a rare use-after-free [1].
Fix this by protecting the rules list accessed by the delayed work with
a lock. We cannot use a spinlock as the activity read operation is
blocking.
[1]
[ 123.331662] ==================================================================
[ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78
[ 123.357080]
[ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209
[ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
[ 123.385970] Call Trace:
[ 123.388734] dump_stack+0xc6/0x11e
[ 123.392568] print_address_description.constprop.4+0x21/0x340
[ 123.403236] __kasan_report.cold.8+0x76/0xb1
[ 123.414884] kasan_report+0xe/0x20
[ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.444034] process_one_work+0xb06/0x19a0
[ 123.453731] worker_thread+0x91/0xe90
[ 123.467348] kthread+0x348/0x410
[ 123.476847] ret_from_fork+0x24/0x30
[ 123.480863]
[ 123.482545] Allocated by task 73:
[ 123.486273] save_stack+0x19/0x80
[ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230
[ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0
[ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820
[ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690
[ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0
[ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990
[ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60
[ 123.532752] process_one_work+0xb06/0x19a0
[ 123.537352] worker_thread+0x91/0xe90
[ 123.541471] kthread+0x348/0x410
[ 123.545103] ret_from_fork+0x24/0x30
[ 123.549113]
[ 123.550795] Freed by task 518:
[ 123.554231] save_stack+0x19/0x80
[ 123.557958] __kasan_slab_free+0x125/0x170
[ 123.562556] kfree+0xd7/0x3a0
[ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0
[ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130
[ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260
[ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290
[ 123.588091] mlxsw_sp_vr_put+0x1db/0x350
[ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0
[ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360
[ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470
[ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120
[ 123.612260] mlxsw_sp_router_fini+0x137/0x384
[ 123.617152] mlxsw_sp_fini+0x30a/0x4a0
[ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600
[ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0
[ 123.634176] devlink_reload+0xb4/0x380
[ 123.638391] devlink_nl_cmd_reload+0x610/0x700
[ 123.643382] genl_rcv_msg+0x6a8/0xdc0
[ 123.647497] netlink_rcv_skb+0x134/0x3a0
[ 123.651904] genl_rcv+0x29/0x40
[ 123.655436] netlink_unicast+0x4d4/0x700
[ 123.659843] netlink_sendmsg+0x7c0/0xc70
[ 123.664251] __sys_sendto+0x265/0x3c0
[ 123.668367] __x64_sys_sendto+0xe2/0x1b0
[ 123.672773] do_syscall_64+0xa0/0x530
[ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 123.682552]
[ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500
[ 123.684238] which belongs to the cache kmalloc-128 of size 128
[ 123.698261] The buggy address is located 32 bytes inside of
[ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580)
[ 123.711303] The buggy address belongs to the page:
[ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0
[ 123.725958] raw: 0200000000000200 dead000000000100 dead000000000122 ffff888236403500
[ 123.734646] raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
[ 123.743315] page dumped because: kasan: bad access detected
[ 123.749562]
[ 123.751241] Memory state around the buggy address:
[ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 123.780904] ^
[ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.801883] ==================================================================
Fixes: cf7221a4f5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0034d395f8 ("powerpc/mm/hash64: Map all the kernel regions in
the same 0xc range") has a bug in the definition of MIN_USER_CONTEXT.
The result is that the context id used for the vmemmap and the lowest
context id handed out to userspace are the same. The context id is
essentially the process identifier as far as the first stage of the
MMU translation is concerned.
This can result in multiple SLB entries with the same VSID (Virtual
Segment ID), accessible to the kernel and some random userspace
process that happens to get the overlapping id, which is not expected
eg:
07 c00c000008000000 40066bdea7000500 1T ESID= c00c00 VSID= 66bdea7 LLP:100
12 0002000008000000 40066bdea7000d80 1T ESID= 200 VSID= 66bdea7 LLP:100
Even though the user process and the kernel use the same VSID, the
permissions in the hash page table prevent the user process from
reading or writing to any kernel mappings.
It can also lead to SLB entries with different base page size
encodings (LLP), eg:
05 c00c000008000000 00006bde0053b500 256M ESID=c00c00000 VSID= 6bde0053b LLP:100
09 0000000008000000 00006bde0053bc80 256M ESID= 0 VSID= 6bde0053b LLP: 0
Such SLB entries can result in machine checks, eg. as seen on a G5:
Oops: Machine check, sig: 7 [#1]
BE PAGE SIZE=64K MU-Hash SMP NR_CPUS=4 NUMA Power Mac
NIP: c00000000026f248 LR: c000000000295e58 CTR: 0000000000000000
REGS: c0000000erfd3d70 TRAP: 0200 Tainted: G M (5.5.0-rcl-gcc-8.2.0-00010-g228b667d8ea1)
MSR: 9000000000109032 <SF,HV,EE,ME,IR,DR,RI> CR: 24282048 XER: 00000000
DAR: c00c000000612c80 DSISR: 00000400 IRQMASK: 0
...
NIP [c00000000026f248] .kmem_cache_free+0x58/0x140
LR [c088000008295e58] .putname 8x88/0xa
Call Trace:
.putname+0xB8/0xa
.filename_lookup.part.76+0xbe/0x160
.do_faccessat+0xe0/0x380
system_call+0x5c/ex68
This happens with 256MB segments and 64K pages, as the duplicate VSID
is hit with the first vmemmap segment and the first user segment, and
older 32-bit userspace maps things in the first user segment.
On other CPUs a machine check is not seen. Instead the userspace
process can get stuck continuously faulting, with the fault never
properly serviced, due to the kernel not understanding that there is
already a HPTE for the address but with inaccessible permissions.
On machines with 1T segments we've not seen the bug hit other than by
deliberately exercising it. That seems to be just a matter of luck
though, due to the typical layout of the user virtual address space
and the ranges of vmemmap that are typically populated.
To fix it we add 2 to MIN_USER_CONTEXT. This ensures the lowest
context given to userspace doesn't overlap with the VMEMMAP context,
or with the context for INVALID_REGION_ID.
Fixes: 0034d395f8 ("powerpc/mm/hash64: Map all the kernel regions in the same 0xc range")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: Christian Marillat <marillat@debian.org>
Reported-by: Romain Dolbeau <romain@dolbeau.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Account for INVALID_REGION_ID, mostly rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200123102547.11623-1-mpe@ellerman.id.au
Hayes Wang says:
====================
r8152: serial fixes
v3:
1. Fix the typos for patch #5 and #6.
2. Modify the commit message of patch #9.
v2:
For patch #2, move declaring the variable "ocp_data".
v1:
These patches are used to fix some issues for RTL8153.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certain platforms, it causes USB reset periodically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8153B with QFN32, disable test IO. Otherwise, it may cause
abnormal behavior for the device randomly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLA MCU clock speed down could only be enabled when tx/rx are disabled.
Otherwise, the packet loss may occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When linking ON, the patch of flow control has to be reset. This
makes sure the patch works normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the runtime resume doesn't work normally for linking change.
1. Reset the settings and status of runtime suspend.
2. Sync the linking status.
3. Poll the linking change.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
