MLX5E_XDP_MAX_MTU was calculated incorrectly. It didn't account for
NET_IP_ALIGN and MLX5E_HW2SW_MTU, and it also misused MLX5_SKB_FRAG_SZ.
This commit fixes the calculations and adds a brief explanation for the
formula used.
Fixes: a26a5bdf3e ("net/mlx5e: Restrict the combination of large MTU and XDP")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
xdp_return_frame releases the frame. It leads to releasing the page, so
it's not allowed to access xdpi.xdpf->len after that, because xdpi.xdpf
is at xdp->data_hard_start after convert_to_xdp_frame. This patch moves
the memory access to precede the return of the frame.
Fixes: 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Since there are more IOT2040 variants with identical hardware but
different asset tags, the asset tag matching should be adjusted to
support them.
For the board name "SIMATIC IOT2000", currently there are 2 types of
hardware, IOT2020 and IOT2040. The IOT2020 is identified by its unique
asset tag. Match on it first. If we then match on the board name only,
we will catch all IOT2040 variants. In the future there will be no other
devices with the "SIMATIC IOT2000" DMI board name but different
hardware.
Signed-off-by: Su Bao Cheng <baocheng.su@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If link is down and autoneg is set to on/off, the status in ethtool does
not change.
The reason is when the link is down the function returns with zero
before changing autoneg value.
Move the checking of link state (up/down) to be performed after setting
autoneg value, in order to be sure that autoneg will change in any case.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver initialization the driver sends a reset to the device and
waits for the firmware to signal that it is ready to continue.
Commit d2f372ba09 ("mlxsw: pci: Increase PCI SW reset timeout")
increased the timeout to 13 seconds due to longer PHY calibration in
Spectrum-2 compared to Spectrum-1.
Recently it became apparent that this timeout is too short and therefore
this patch increases it again to a safer limit that will be reduced in
the future.
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Fixes: d2f372ba09 ("mlxsw: pci: Increase PCI SW reset timeout")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both Spectrum-1 and Spectrum-2 chips are currently configured such that
pairs of TC n (which is used for UC traffic) and TC n+8 (which is used
for MC traffic) are feeding into the same subgroup. Strict
prioritization is configured between the two TCs, and by enabling
MC-aware mode on the switch, the lower-numbered (UC) TCs are favored
over the higher-numbered (MC) TCs.
On Spectrum-2 however, there is an issue in configuration of the
MC-aware mode. As a result, MC traffic is prioritized over UC traffic.
To work around the issue, configure the MC TCs with DWRR mode (while
keeping the UC TCs in strict mode).
With this patch, the multicast-unicast arbitration results in the same
behavior on both Spectrum-1 and Spectrum-2 chips.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple of spelling mistakes in NL_SET_ERR_MSG_MOD error
messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warn this:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c: In function ndesc_init_rx_desc:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:138:6: warning: variable 'bfsize1' set but not used [-Wunused-but-set-variable]
Like enh_desc_init_rx_desc, we should use bfsize1
in ndesc_init_rx_desc to calculate 'p->des1'
Fixes: 583e636141 ("net: stmmac: use correct DMA buffer size in the RX descriptor")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preventive cleanup that may save troubles later.
No need to cancel repeateadly queued work if code is properly
refactored.
Don't let the ethtool -s process interfere with the stat workqueue
scheduling.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a DP_INFO message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a BNX2X_ERR message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcrPOfAAoJEEg/ir3gV/o+c1sIAIuVUmF95OK6BxrNxQ31HN7i
0V/OW29V6B5musqyGXVa90nl9wJ9BE2tmtHsg2HPABXdGdiYhNRP7Tm+aq+QYBe3
8kJVk5U+HCLeHvf9k3dpJZokMzAgEhuWAbuAE1YelYUtbOXO9Zrj2uTL1NHJTYyc
SNOg9+gATOMsOAuiUyygN0XMoYESTsUE7UH4tuhyYr44cKR85qOQDPAlcDEHGTfO
uHWwmOznZqFVJUVyfwtEkTojsxNiW+QA2PR5faX/+eI7746qXOAzYq2JSjtNEyTz
4xB9a+t47xpGDw4Svwu51pDw+4Uiiy1Yv0kOKKpBqrCk892bZ8l1gWcHRgjYx/8=
=9wkB
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-04-09
This series provides some fixes to mlx5 driver.
I've cc'ed some of the checksum fixes to Eric Dumazet and i would like to get
his feedback before you pull.
For -stable v4.19
('net/mlx5: FPGA, tls, idr remove on flow delete')
('net/mlx5: FPGA, tls, hold rcu read lock a bit longer')
For -stable v4.20
('net/mlx5e: Rx, Check ip headers sanity')
('Revert "net/mlx5e: Enable reporting checksum unnecessary also for L3 packets"')
('net/mlx5e: Rx, Fixup skb checksum for packets with tail padding')
For -stable v5.0
('net/mlx5e: Switch to Toeplitz RSS hash by default')
('net/mlx5e: Protect against non-uplink representor for encap')
('net/mlx5e: XDP, Avoid checksum complete when XDP prog is loaded')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the overflow handling from the hardware interrupt status analysis.
The interrupt status is a single register and is common for all PFs. The
first PF reading the register is not necessarily the one who overflowed.
All PFs must check their overflow status on every attention.
In this change we clear the sticky indication in the attention handler to
allow doorbells to be processed again as soon as possible, but running
the doorbell recovery is scheduled for the periodic handler to reduce the
time spent in the attention handler.
Checking the need for DORQ flush was changed to "db_bar_no_edpm" because
qed_edpm_enabled()'s result could change dynamically and might have
prevented a needed flush.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the DORQ (doorbell block) is overflowed, all PFs get attentions at the
same time. If one PF finished handling the attention before another PF even
started, the second PF might miss the DORQ's attention bit and not handle
the attention at all.
If the DORQ attention is missed and the issue is not resolved, another
attention will not be sent, therefore each attention is treated as a
potential DORQ attention.
As a result, the attention callback is called more frequently so the debug
print was moved to reduce its quantity.
The number of periodic doorbell recovery handler schedules was reduced
because it was the previous way to mitigating the missed attention issue.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the condition which verifies that doorbell address is inside the
doorbell bar by checking that the end of the address is within range
as well.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DB_REC_DRY_RUN (running doorbell recovery without sending doorbells) is
never used. DB_REC_ONCE (send a single doorbell from the doorbell recovery)
is not needed anymore because by running the periodic handler we make sure
we check the overflow status later instead.
This patch is needed because in the next patches, the only doorbell
recovery type being used is DB_REC_REAL_DEAL, and the fixes are much
cleaner without this enum.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The err2 error return path calls qede_ptp_disable that cleans up
on an error and frees ptp. After this, the free'd ptp is dereferenced
when ptp->clock is set to NULL and the code falls-through to error
path err1 that frees ptp again.
Fix this by calling qede_ptp_disable and exiting via an error
return path that does not set ptp->clock or kfree ptp.
Addresses-Coverity: ("Write to pointer after free")
Fixes: 035744975a ("qede: Add support for PTP resource locking.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if a pci dma mapping failure is detected a free'd
memblock address is returned rather than a NULL (that indicates
an error). Fix this by ensuring NULL is returned on this error case.
Addresses-Coverity: ("Use after free")
Fixes: 528f727279 ("vxge: code cleanup and reorganization")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SOC like i.MX6SX clock have some limits:
- ahb clock should be disabled before ipg.
- ahb and ipg clocks are required for MAC MII bus.
So, move the ahb clock to runtime management together with
ipg clock.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The thunderx driver forbids to load an eBPF program if the MTU is too high,
but this can be circumvented by loading the eBPF, then raising the MTU.
Fix this by limiting the MTU if an eBPF program is already loaded.
Fixes: 05c773f52b ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The thunderx driver splits frames bigger than 1530 bytes to multiple
pages, making impossible to run an eBPF program on it.
This leads to a maximum MTU of 1508 if QinQ is in use.
The thunderx driver forbids to load an eBPF program if the MTU is higher
than 1500 bytes. Raise the limit to 1508 so it is possible to use L2
protocols which need some more headroom.
Fixes: 05c773f52b ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While determining offload capabilities of backing hardware during
a device reset, the driver is clobbering current feature settings.
Update hw_features on reset instead of features unless a feature
is enabled that is no longer supported on the current backing device.
Also enable features that were not supported prior to the reset but
were previously enabled or requested by the user.
This can occur if the reset is the result of a carrier change, such
as a device failover or partition migration.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable Generic Receive Offload in the ibmvnic driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-1, when a multicast packet is admitted to the shared buffer
it increases the quotas of all the ports and {port, TC} to which it is
forwarded to.
The above means that multicast packets are accounted multiple times in
the shared buffer and can therefore cause the associated shared buffer
pool to fill up very quickly.
To work around this issue, commit e83c045e53 ("mlxsw:
spectrum_buffers: Configure MC pool") added a dedicated multicast pool
in which multicast packets are accounted.
The issue is not present in Spectrum-2, but in order to be backward
compatible with Spectrum-1, its default behavior is to allow a multicast
packet to increase multiple egress quotas instead of one.
Until the new (non-backward compatible) mode is supported, configure a
dedicated multicast pool as in Spectrum-1.
Fixes: fe099bf682 ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 74bc993974 ("mlxsw: spectrum_router: Veto unsupported RIF MAC
addresses") enabled the driver to veto router interface (RIF) MAC
addresses that it cannot support.
This check should only be performed for interfaces for which the driver
actually configures a RIF. A VRF upper is not one of them, so ignore it.
Without this patch it is not possible to set an IP address on the VRF
device and use it as a loopback.
Fixes: 74bc993974 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue is used to periodically update the networking stack about
activity / statistics of various objects such as neighbours and TC
actions.
It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag.
Fixes: 3d5479e920 ("mlxsw: core: Remove deprecated create_workqueue")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAD workqueue is used to handle retransmission of EMAD packets that
contain configuration data for the device's firmware.
Given the workers need to allocate these packets and that the code is
not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM
flag.
Fixes: d965465b60 ("mlxsw: core: Fix possible deadlock")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although XOR hash function can perform very well on some special use
cases, to align with all drivers, mlx5 driver should use Toeplitz hash
by default.
Toeplitz is more stable for the general use case and it is more standard
and reliable.
On top of that, since XOR (MLX5_RX_HASH_FN_INVERTED_XOR8) gives only a
repeated 8 bits pattern. When used for udp tunneling RSS source port
manipulation it results in fixed source port, which will cause bad RSS
spread.
Fixes: 2be6967cdb ("net/mlx5e: Support ETH_RSS_HASH_XOR")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This reverts commit b820e6fb09.
Prior the commit we are reverting, checksum unnecessary was only set when
both the L3 OK and L4 OK bits are set on the CQE. This caused packets
of IP protocols such as SCTP which are not dealt by the current HW L4
parser (hence the L4 OK bit is not set, but the L4 header type none bit
is set) to go through the checksum none code, where currently we wrongly
report checksum unnecessary for them, a regression. Fix this by a revert.
Note that on our usual track we report checksum complete, so the revert
isn't expected to have any notable performance impact. Also, when we are
not on the checksum complete track, the L4 protocols for which we report
checksum none are not high performance ones, we will still report
checksum unnecessary for UDP/TCP.
Fixes: b820e6fb09 ("net/mlx5e: Enable reporting checksum unnecessary also for L3 packets")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Avi Urman <aviu@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
TC encap offload is supported only for the physical uplink
representor. Fail for non uplink representor.
Fixes: 3e621b19b0 ("net/mlx5e: Support TC encapsulation offloads with upper devices")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In the two places is_last_ethertype_ip is being called, the caller will
be looking inside the ip header, to be safe, add ip{4,6} header sanity
check. And return true only on valid ip headers, i.e: the whole header
is contained in the linear part of the skb.
Note: Such situation is very rare and hard to reproduce, since mlx5e
allocates a large enough headroom to contain the largest header one can
imagine.
Fixes: fe1dc06999 ("net/mlx5e: don't set CHECKSUM_COMPLETE on SCTP packets")
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When an ethernet frame with ip payload is padded, the padding octets are
not covered by the hardware checksum.
Prior to the cited commit, skb checksum was forced to be CHECKSUM_NONE
when padding is detected. After it, the kernel will try to trim the
padding bytes and subtract their checksum from skb->csum.
In this patch we fixup skb->csum for any ip packet with tail padding of
any size, if any padding found.
FCS case is just one special case of this general purpose patch, hence,
it is removed.
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"),
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
XDP programs might change packets data contents which will make the
reported skb checksum (checksum complete) invalid.
When XDP programs are loaded/unloaded set/clear rx RQs
MLX5E_RQ_STATE_NO_CSUM_COMPLETE flag.
Fixes: 86994156c7 ("net/mlx5e: XDP fast RX drop bpf programs support")
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When requested to recover from error, the tx reporter might open new
channels and close the existing ones. Use safe channels switch flow in
order to guarantee opened channels at the end of the recover flow.
For this purpose, define mlx5e_safe_reopen_channels function and use it
within those flows.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Skip recover operation if interface is in down state as TX objects are
not open. This fixes a bug were the recover flow re-opened TX objects
which were not opened before, leading to a possible memory leak at
driver unload.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow is kfreed on mlx5_fpga_tls_del_flow but kept in the idr data
structure, this is risky and can cause use-after-free, since the
idr_remove is delayed until tls_send_teardown_cmd completion.
Instead of delaying idr_remove, in this patch we do it on
mlx5_fpga_tls_del_flow, before actually kfree(flow).
Added synchronize_rcu before kfree(flow)
Fixes: ab412e1dd7 ("net/mlx5: Accel, add TLS rx offload routines")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To avoid use-after-free, hold the rcu read lock until we are done copying
flow data into the command buffer.
Fixes: ab412e1dd7 ("net/mlx5: Accel, add TLS rx offload routines")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If the RX completion indicates RX buffers errors, the RX ring will be
disabled by firmware and no packets will be received on that ring from
that point on. Recover by resetting the device.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is logic to check that the RX/TPA consumer index is the expected
index to work around a hardware problem. However, the potentially bad
consumer index is first used to index into an array to reference an entry.
This can potentially crash if the bad consumer index is beyond legal
range. Improve the logic to use the consumer index for dereferencing
after the validity check and log an error message.
Fixes: fa7e28127a ("bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been
enabled for this skb. It does fix the issue where normal socks that
aren't expecting a timestamp will not wake up on select, but when a
user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work.
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a significant number of reports that re-enabling ASPM causes
different issues, ranging from decreased performance to system not
booting at all. This affects only a minority of users, but the number
of affected users is big enough that we better switch off ASPM again.
This will hurt notebook users who are not affected by the issues, they
may see decreased battery runtime w/o ASPM. With the PCI core folks is
being discussed to add generic sysfs attributes to control ASPM.
Once this is in place brave enough users can re-enable ASPM on their
system.
Fixes: a99790bf5c ("r8169: Reinstate ASPM Support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BITS_TO_LONGS() uses DIV_ROUND_UP() because of
this ppmax value can be greater than available
per cpu page pods.
This patch removes BITS_TO_LONGS() to fix this
issue.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some sparse warnings in the HNS drivers:
warning: incorrect type in assignment (different address spaces)
expected void [noderef] <asn:2> *io_base
got void *vaddr
warning: cast removes address space '<asn:2>' of expression
[...]
Add __iomem and change all the u8 __iomem to void __iomem to
fix these kind of warnings.
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:2> *base
got unsigned char [usertype] *base_addr
warning: cast to restricted __le16
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype] tbl_tcam_data_high
got restricted __le32 [usertype]
warning: cast to restricted __le32
[...]
These variables used u32/u16 as their type, and finally as a
parameter of writel(), writel() will do the cpu_to_le32 coversion
so remove the little endian covert code to fix these kind of warnings.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
