This is likely a copy'n'paste mistake. The amount of ILT lines to
reserve for a single VF was being multiplied by the total VFs count.
This led to a huge redundancy in reservation and potential lines
drainouts.
Fixes: 1408cc1fa4 ("qed: Introduce VFs")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
25ms sleep cycles in waiting for PF response are excessive and may lead
to different timeout failures.
Start to wait with short udelays, and in most cases polling will end
here. If the time was not sufficient, switch to msleeps.
usleep_range() may go far beyond 100us depending on platform and tick
configuration, hence atomic udelays for consistency.
Also add explicit DMA barriers since 'done' always comes from a shared
request-response DMA pool, and note that in the comment nearby.
Fixes: 1408cc1fa4 ("qed: Introduce VFs")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set rdma_wq pointer to NULL after destroying the workqueue and check
for it when adding new events to fix crashes on driver unload.
Fixes: cee9fbd8e2 ("qede: Add qedr framework")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qed_spq_unregister_async_cb() should be called before
qed_rdma_info_free() to avoid crash-spawning uses-after-free.
Instead of calling it from each subsystem exit code, do it in one place
on PF down.
Fixes: 291d57f67d ("qed: Fix rdma_info structure allocation")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before, we took a reference to the creating netns if the new netns was
different. This caused issues with circular references, with two
wireguard interfaces swapping namespaces. The solution is to rather not
take any extra references at all, but instead simply invalidate the
creating netns pointer when that netns is deleted.
In order to prevent this from happening again, this commit improves the
rough object leak tracking by allowing it to account for created and
destroyed interfaces, aside from just peers and keys. That then makes it
possible to check for the object leak when having two interfaces take a
reference to each others' namespaces.
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes an error condition reported by checkpatch.pl which caused by
assigning a variable in an if condition in wg_noise_handshake_consume_
initiation().
Signed-off-by: Frank Werner-Krippendorf <mail@hb9fxq.ch>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reports an use-after-free in workqueue context:
BUG: KASAN: use-after-free in mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
__smsc95xx_mdio_read drivers/net/usb/smsc95xx.c:217 [inline]
smsc95xx_mdio_read+0x583/0x870 drivers/net/usb/smsc95xx.c:278
check_carrier+0xd1/0x2e0 drivers/net/usb/smsc95xx.c:644
process_one_work+0x777/0xf90 kernel/workqueue.c:2274
worker_thread+0xa8f/0x1430 kernel/workqueue.c:2420
kthread+0x2df/0x300 kernel/kthread.c:255
It looks like that smsc95xx_unbind() is freeing the structures that are
still in use by the concurrently running workqueue callback. Thus switch
to using cancel_delayed_work_sync() to ensure the work callback really
is no longer active.
Reported-by: syzbot+29dc7d4ae19b703ff947@syzkaller.appspotmail.com
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The second commit cited below performed a cast of 'u32 buffsize' to
'(u16 *)' when calling mlxsw_sp_port_headroom_8x_adjust():
mlxsw_sp_port_headroom_8x_adjust(mlxsw_sp_port, (u16 *) &buffsize);
Colin noted that this will behave differently on big endian
architectures compared to little endian architectures.
Fix this by following Colin's suggestion and have the function accept
and return 'u32' instead of passing the current size by reference.
Fixes: da382875c6 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Fixes: 60833d54d5 ("mlxsw: spectrum: Adjust headroom buffers for 8x ports")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Suggested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7ae7ad2f11 ("net: phy: smsc: use phy_read_poll_timeout()
to simplify the code") will print a lot of logs as follows when Ethernet
cable is not connected:
[ 4.473105] SMSC LAN8710/LAN8720 2188000.ethernet-1:00: lan87xx_read_status failed: -110
When wait 640 ms for check ENERGYON bit, the timeout should not be
regarded as an actual error and an error message also should not be
printed. due to a hardware bug in LAN87XX device, it leads to unstable
detection of plugging in Ethernet cable when LAN87xx is in Energy Detect
Power-Down mode. the workaround for it involves, when the link is down,
and at each read_status() call:
- disable EDPD mode, forcing the PHY out of low-power mode
- waiting 640ms to see if we have any energy detected from the media
- re-enable entry to EDPD mode
This is presumably enough to allow the PHY to notice that a cable is
connected, and resume normal operations to negotiate with the partner.
The problem is that when no media is detected, the 640ms wait times
out and this commit was modified to prints an error message. it is an
inappropriate conversion by used phy_read_poll_timeout() to introduce
this bug. so fix this issue by use read_poll_timeout() to replace
phy_read_poll_timeout().
Fixes: 7ae7ad2f11 ("net: phy: smsc: use phy_read_poll_timeout() to simplify the code")
Reported-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typically the firmware takes care that tp->ocp_base is reset to its
default value. That's not the case (at least) for RTL8117.
As a result subsequent PHY access reads/writes the wrong page and
the link is broken. Fix this be resetting tp->ocp_base explicitly.
Fixes: 229c1e0dfd ("r8169: load firmware for RTL8168fp/RTL8117")
Reported-by: Aaron Ma <mapengyu@gmail.com>
Tested-by: Aaron Ma <mapengyu@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continue the reset path when partner adapter is not ready or H_CLOSED is
returned from reset crq. This patch allows the CRQ init to proceed to
establish a valid CRQ for traffic to flow after reset.
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even with moving netif_tx_disable() to an earlier point when
taking down the queues for a reconfiguration, we still end
up with the occasional netdev watchdog Tx Timeout complaint.
The old method of using netif_trans_update() works fine for
queue 0, but has no effect on the remaining queues. Using
netif_device_detach() allows us to signal to the watchdog to
ignore us for the moment.
Fixes: beead698b1 ("ionic: Add the basic NDO callbacks for netdev support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max MTU limit defined for ibmveth is not accounting for
virtual ethernet buffer overhead, which is twenty-two additional
bytes set aside for the ethernet header and eight additional bytes
of an opaque handle reserved for use by the hypervisor. Update the
max MTU to reflect this overhead.
Fixes: d894be57ca ("ethernet: use net core MTU range checking in more drivers")
Fixes: 110447f826 ("ethernet: fix min/max MTU typos")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the representor is removed, then identify the indirect flow_blocks
that need to be removed by the release callback and the port representor
structure. To identify the port representor structure, a new
indr.cb_priv field needs to be introduced. The flow_block also needs to
be removed from the driver list from the cleanup path.
Fixes: 1fac52da59 ("net: flow_offload: consolidate indirect flow_block infrastructure")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare fix the bug in the next patch. use flow_indr_block_cb_alloc/remove
function and remove the __flow_block_indr_binding.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, trying to change the DF parameter of a geneve device does
nothing:
# ip -d link show geneve1
14: geneve1: <snip>
link/ether <snip>
geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip>
# ip link set geneve1 type geneve id 1 df unset
# ip -d link show geneve1
14: geneve1: <snip>
link/ether <snip>
geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip>
We just need to update the value in geneve_changelink.
Fixes: a025fb5f49 ("geneve: Allow configuration of DF behaviour")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN tag insertion/extraction offload is correctly
activated at probe time but deactivation of this feature
(i.e. via ethtool) is broken. Toggling works only for
Tx/Rx ring 0 of a PF, and is ignored for the other rings,
including the VF rings.
To fix this, the existing VLAN offload toggling code
was extended to all the rings assigned to a netdevice,
instead of the default ring 0 (likely a leftover from the
early validation days of this feature). And the code was
moved to the common set_features() function to fix toggling
for the VF driver too.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Undo previously done operation in case macb_phylink_connect()
fails. Since macb_reset_hw() is the 1st undo operation the
napi_exit label was renamed to reset_hw.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 02a6efcab6 ("net: phy: allow scanning busses with missing
phys") added a special condition to return -ENODEV in case -ENODEV or
-EIO was returned from the first read of the MII_PHYSID1 register.
In case the MDIO bus data line pull-up is not strong enough, the MDIO
bus controller will not flag this as a read error. This can happen when
a pluggable daughter card is not connected and weak internal pull-ups
are used (since that is the only option, otherwise the pins are
floating).
The second read of MII_PHYSID2 will be correctly flagged an error
though, but now we will return -EIO which will be treated as a hard
error, thus preventing MDIO bus scanning loops to continue succesfully.
Apply the same logic to both register reads, thus allowing the scanning
logic to proceed.
Fixes: 02a6efcab6 ("net: phy: allow scanning busses with missing phys")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the AF_XDP buffer allocator was introduced, the Rx SW ring
"rx_bi" allocation was moved from i40e_setup_rx_descriptors()
function, and was instead done in the i40e_configure_rx_ring()
function.
This broke the ethtool set_ringparam() hook for changing the Rx
descriptor count, which was relying on i40e_setup_rx_descriptors() to
handle the allocation.
Fix this by adding an explicit i40e_alloc_rx_bi() call to
i40e_set_ringparam().
Fixes: be1222b585 ("i40e: Separate kernel allocated rx_bi rings from AF_XDP rings")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The READ_ONCE macro is used when reading rings prior to accessing the
statistics pointer. The corresponding WRITE_ONCE usage when allocating and
freeing the rings to ensure protected access was not in place. Introduce
this.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
READ_ONCE should be used when reading rings prior to accessing the
statistics pointer. Introduce this as well as the corresponding WRITE_ONCE
usage when allocating and freeing the rings, to ensure protected access.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
READ_ONCE should be used when reading rings prior to accessing the
statistics pointer. Introduce this as well as the corresponding WRITE_ONCE
usage when allocating and freeing the rings, to ensure protected access.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver function tg3_io_error_detected() calls napi_disable twice,
without an intervening napi_enable, when the number of EEH errors exceeds
eeh_max_freezes, resulting in an indefinite sleep while holding rtnl_lock.
Add check for pcierr_recovery which skips code already executed for the
"Frozen" state.
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code to handle multiproto configuration is missing.
Fixes: 4b5f67232d ("net: Special handling for IP & MPLS")
Signed-off-by: Martin <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action requires the VLAN awareness state of the switch to be of the
same type as the key that's being added:
- If the switch is unaware of VLAN, then the tc filter key must only
contain the destination MAC address.
- If the switch is VLAN-aware, the key must also contain the VLAN ID and
PCP.
But this check doesn't work unless we verify the VLAN awareness state on
both the "if" and the "else" branches.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action requires the VLAN awareness state of the switch to be of the
same type as the key that's being added:
- If the switch is unaware of VLAN, then the tc filter key must only
contain the destination MAC address.
- If the switch is VLAN-aware, the key must also contain the VLAN ID and
PCP.
But this check doesn't work unless we verify the VLAN awareness state on
both the "if" and the "else" branches.
Fixes: dfacc5a23e ("net: dsa: sja1105: support flow-based redirection via virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This shouldn't be there.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The older SoCs like Armada XP support a 2500BaseX mode in the datasheets
referred to as DR-SGMII (Double rated SGMII) or HS-SGMII (High Speed
SGMII). This is an upclocked 1000BaseX mode, thus
PHY_INTERFACE_MODE_2500BASEX is the appropriate mode define for it.
adding support for it merely means writing the correct magic value into
the MVNETA_SERDES_CFG register.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MVNETA_SERDES_CFG register is only available on older SoCs like the
Armada XP. On newer SoCs like the Armada 38x the fields are moved to
comphy. This patch moves the writes to this register next to the comphy
initialization, so that depending on the SoC either comphy or
MVNETA_SERDES_CFG is configured.
With this we no longer write to the MVNETA_SERDES_CFG on SoCs where it
doesn't exist.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set up vlan_features for use by any vlans above us.
Fixes: beead698b1 ("ionic: Add the basic NDO callbacks for netdev support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is busy resetting queues after a change in
MTU or queue parameters, don't bother checking the link,
wait until the next watchdog cycle.
Fixes: 987c0871e8 ("ionic: check for linkup in watchdog")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a AX88179 device (0b95:1790), I see two bytes of appended data on
every RX packet. For example, this 48-byte ping, using 0xff as a
payload byte:
04:20:22.528472 IP 192.168.1.1 > 192.168.1.2: ICMP echo request, id 2447, seq 1, length 64
0x0000: 000a cd35 ea50 000a cd35 ea4f 0800 4500
0x0010: 0054 c116 4000 4001 f63e c0a8 0101 c0a8
0x0020: 0102 0800 b633 098f 0001 87ea cd5e 0000
0x0030: 0000 dcf2 0600 0000 0000 ffff ffff ffff
0x0040: ffff ffff ffff ffff ffff ffff ffff ffff
0x0050: ffff ffff ffff ffff ffff ffff ffff ffff
0x0060: ffff 961f
Those last two bytes - 96 1f - aren't part of the original packet.
In the ax88179 RX path, the usbnet rx_fixup function trims a 2-byte
'alignment pseudo header' from the start of the packet, and sets the
length from a per-packet field populated by hardware. It looks like that
length field *includes* the 2-byte header; the current driver assumes
that it's excluded.
This change trims the 2-byte alignment header after we've set the packet
length, so the resulting packet length is correct. While we're moving
the comment around, this also fixes the spelling of 'pseudo'.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't get per-cpu pointer with preemption enabled in nft_set_pipapo,
fix from Stefano Brivio.
2) Fix memory leak in ctnetlink, from Pablo Neira Ayuso.
3) Multiple definitions of MPTCP_PM_MAX_ADDR, from Geliang Tang.
4) Accidently disabling NAPI in non-error paths of macb_open(), from
Charles Keepax.
5) Fix races between alx_stop and alx_remove, from Zekun Shen.
6) We forget to re-enable SRIOV during resume in bnxt_en driver, from
Michael Chan.
7) Fix memory leak in ipv6_mc_destroy_dev(), from Wang Hai.
8) rxtx stats use wrong index in mvpp2 driver, from Sven Auhagen.
9) Fix memory leak in mptcp_subflow_create_socket error path, from Wei
Yongjun.
10) We should not adjust the TCP window advertised when sending dup acks
in non-SACK mode, because it won't be counted as a dup by the sender
if the window size changes. From Eric Dumazet.
11) Destroy the right number of queues during remove in mvpp2 driver,
from Sven Auhagen.
12) Various WOL and PM fixes to e1000 driver, from Chen Yu, Vaibhav
Gupta, and Arnd Bergmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (35 commits)
e1000e: fix unused-function warning
e1000: use generic power management
e1000e: Do not wake up the system via WOL if device wakeup is disabled
lan743x: add MODULE_DEVICE_TABLE for module loading alias
mlxsw: spectrum: Adjust headroom buffers for 8x ports
bareudp: Fixed configuration to avoid having garbage values
mvpp2: remove module bugfix
tcp: grow window for OOO packets only for SACK flows
mptcp: fix memory leak in mptcp_subflow_create_socket()
netfilter: flowtable: Make nf_flow_table_offload_add/del_cb inline
net/sched: act_ct: Make tcf_ct_flow_table_restore_skb inline
net: dsa: sja1105: fix PTP timestamping with large tc-taprio cycles
mvpp2: ethtool rxtx stats fix
MAINTAINERS: switch to my private email for Renesas Ethernet drivers
rocker: fix incorrect error handling in dma_rings_init
test_objagg: Fix potential memory leak in error handling
net: ethernet: mtk-star-emac: simplify interrupt handling
mld: fix memory leak in ipv6_mc_destroy_dev()
bnxt_en: Return from timer if interface is not in open state.
bnxt_en: Fix AER reset logic on 57500 chips.
...
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2020-06-16
This series contains fixes to e1000 and e1000e.
Chen fixes an e1000e issue where systems could be waken via WoL, even
though the user has disabled the wakeup bit via sysfs.
Vaibhav Gupta updates the e1000 driver to clean up the legacy Power
Management hooks.
Arnd Bergmann cleans up the inconsistent use CONFIG_PM_SLEEP
preprocessor tags, which also resolves the compiler warnings about the
possibility of unused structure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_PM_SLEEP #ifdef checks in this file are inconsistent,
leading to a warning about sometimes unused function:
drivers/net/ethernet/intel/e1000e/netdev.c:137:13: error: unused function 'e1000e_check_me' [-Werror,-Wunused-function]
Rather than adding more #ifdefs, just remove them completely
and mark the PM functions as __maybe_unused to let the compiler
work it out on it own.
Fixes: e086ba2fcc ("e1000e: disable s0ix entry and exit flows for ME systems")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With legacy PM hooks, it was the responsibility of a driver to manage PCI
states and also the device's power state. The generic approach is to let PCI
core handle the work.
e1000_suspend() calls __e1000_shutdown() to perform intermediate tasks.
__e1000_shutdown() modifies the value of "wake" (device should be wakeup
enabled or not), responsible for controlling the flow of legacy PM.
Since, PCI core has no idea about the value of "wake", new code for generic
PM may produce unexpected results. Thus, use "device_set_wakeup_enable()"
to wakeup-enable the device accordingly.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the system will be woken up via WOL(Wake On LAN) even if the
device wakeup ability has been disabled via sysfs:
cat /sys/devices/pci0000:00/0000:00:1f.6/power/wakeup
disabled
The system should not be woken up if the user has explicitly
disabled the wake up ability for this device.
This patch clears the WOL ability of this network device if the
user has disabled the wake up ability in sysfs.
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver")
Reported-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Without a MODULE_DEVICE_TABLE the attributes are missing that create
an alias for auto-loading the module in userspace via hotplug.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port's headroom buffers are used to store packets while they
traverse the device's pipeline and also to store packets that are egress
mirrored.
On Spectrum-3, ports with eight lanes use two headroom buffers between
which the configured headroom size is split.
In order to prevent packet loss, multiply the calculated headroom size
by two for 8x ports.
Fixes: da382875c6 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code to initialize the conf structure while gathering the configuration
of the device was missing.
Fixes: 571912c69f ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Martin <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remove function does not destroy all
BM Pools when per cpu pool is active.
When reloading the mvpp2 as a module the BM Pools
are still active in hardware and due to the bug
have twice the size now old + new.
This eventually leads to a kernel crash.
v2:
* add Fixes tag
Fixes: 7d04b0b13b ("mvpp2: percpu buffers")
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code should
always use “flexible array members”[1] for these cases. The older style of
one-element or zero-length arrays should no longer be used[2].
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://github.com/KSPP/linux/issues/21
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
It isn't actually described clearly at all in UM10944.pdf, but on TX of
a management frame (such as PTP), this needs to happen:
- The destination MAC address (i.e. 01-80-c2-00-00-0e), along with the
desired destination port, need to be installed in one of the 4
management slots of the switch, over SPI.
- The host can poll over SPI for that management slot's ENFPORT field.
That gets unset when the switch has matched the slot to the frame.
And therein lies the problem. ENFPORT does not mean that the packet has
been transmitted. Just that it has been received over the CPU port, and
that the mgmt slot is yet again available.
This is relevant because of what we are doing in sja1105_ptp_txtstamp_skb,
which is called right after sja1105_mgmt_xmit. We are in a hard
real-time deadline, since the hardware only gives us 24 bits of TX
timestamp, so we need to read the full PTP clock to reconstruct it.
Because we're in a hurry (in an attempt to make sure that we have a full
64-bit PTP time which is as close as possible to the actual transmission
time of the frame, to avoid 24-bit wraparounds), first we read the PTP
clock, then we poll for the TX timestamp to become available.
But of course, we don't know for sure that the frame has been
transmitted when we read the full PTP clock. We had assumed that ENFPORT
means it has, but the assumption is incorrect. And while in most
real-life scenarios this has never been caught due to software delays,
nowhere is this fact more obvious than with a tc-taprio offload, where
PTP traffic gets a small timeslot very rarely (example: 1 packet per 10
ms). In that case, we will be reading the PTP clock for timestamp
reconstruction too early (before the packet has been transmitted), and
this renders the reconstruction procedure incorrect (see the assumptions
described in the comments found on function sja1105_tstamp_reconstruct).
So the PTP TX timestamps will be off by 1<<24 clock ticks, or 135 ms
(1 tick is 8 ns).
So fix this case of premature optimization by simply reordering the
sja1105_ptpegr_ts_poll and the sja1105_ptpclkval_read function calls. It
turns out that in practice, the 135 ms hard deadline for PTP timestamp
wraparound is not so hard, since even the most bandwidth-intensive PTP
profiles, such as 802.1AS-2011, have a sync frame interval of 125 ms.
So if we couldn't deliver a timestamp in 135 ms (which we can), we're
toast and have much bigger problems anyway.
Fixes: 47ed985e97 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool rx and tx queue statistics are reporting wrong values.
Fix reading out the correct ones.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rocker_dma_rings_init, the goto blocks in case of errors
caused by the functions rocker_dma_cmd_ring_waits_alloc() and
rocker_dma_ring_create() are incorrect. The patch fixes the
order consistent with cleanup in rocker_dma_rings_fini().
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
During development we tried to make the interrupt handling as fine-grained
as possible with TX and RX interrupts being disabled/enabled independently
and the counter registers reset from workqueue context.
Unfortunately after thorough testing of current mainline, we noticed the
driver has become unstable under heavy load. While this is hard to
reproduce, it's quite consistent in the driver's current form.
This patch proposes to go back to the previous approach of doing all
processing in napi context with all interrupts masked in order to make the
driver usable in mainline linux. This doesn't impact the performance on
pumpkin boards at all and it's in line with what many ethernet drivers do
in mainline linux anyway.
At the same time we're adding a FIXME comment about the need to improve
the interrupt handling.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
