This patch adds support for PID 0x9625 of YUGA CLM920-NC5.
YUGA CLM920-NC5 needs to enable QMI_WWAN_QUIRK_DTR before QMI operation.
qmicli -d /dev/cdc-wdm0 -p --dms-get-revision
[/dev/cdc-wdm0] Device revision retrieved:
Revision: 'CLM920_NC5-V1 1 [Oct 23 2016 19:00:00]'
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that the dummy byte we add to avoid
ZLPs can be forwarded by the modem to the PGW/GGSN, and that
some operators will drop the connection if this happens.
In theory, QMI devices are based on CDC ECM and should as such
both support ZLPs and silently ignore the dummy byte. The latter
assumption failed. Let's test out the first.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Telit ME910 PID 0x1101.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sierra Wireless EM7565 is an Qualcomm MDM9x50 based M.2 modem.
The USB id is added to qmi_wwan.c to allow QMI communication
with the EM7565.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qmi_wwan minidriver support a 'raw-ip' mode where frames are
received without any ethernet header. This causes alignment issues
because the skbs allocated by usbnet are "IP aligned".
Fix by allowing minidrivers to disable the additional alignment
offset. This is implemented using a per-device flag, since the same
minidriver also supports 'ethernet' mode.
Fixes: 32f7adf633 ("net: qmi_wwan: support "raw IP" mode")
Reported-and-tested-by: Jay Foster <jay@systech.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both
CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel development
board (EVB). The USB id is added to qmi_wwan.c to allow QMI
communication with the BG96.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
_dev_ is being dereferenced before it is null checked, hence there
is a potential null pointer dereference.
Fix this by moving the pointer dereference after _dev_ has been null
checked.
Addresses-Coverity-ID: 1462020
Fixes: bb1b40c7cb ("usbnet: ipheth: prevent TX queue timeouts when device not ready")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.
This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Johan Hovold <johan@kernel.org>
Reported-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GetNtbFormat and SetNtbFormat requests operate on 16 bit little
endian values. We get away with ignoring this most of the time, because
we only care about USB_CDC_NCM_NTB16_FORMAT which is 0x0000. This
fails for USB_CDC_NCM_NTB32_FORMAT.
Fix comparison between LE value from device and constant by converting
the constant to LE.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Fixes: 2b02c20ce0 ("cdc_ncm: Set NTB format again after altsetting switch for Huawei devices")
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: Christian Panton <christian@panton.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iOS devices require the host to be "trusted" before servicing network
packets. Establishing trust requires the user to confirm a dialog on the
iOS device.Until trust is established, the iOS device will silently discard
network packets from the host. Currently, the ipheth driver does not detect
whether an iOS device has established trust with the host, and immediately
sets up the transmit queues.
This causes the following problems:
- Kernel taint due to WARN() in netdev watchdog.
- Dmesg spam ("TX timeout").
- Disruption of user space networking activity (dhcpd, etc...) when new
interface comes up but cannot be used.
- Unnecessary host and device wakeups and USB traffic
Example dmesg output:
[ 1101.319778] NETDEV WATCHDOG: eth1 (ipheth): transmit queue 0 timed out
[ 1101.319817] ------------[ cut here ]------------
[ 1101.319828] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:316 dev_watchdog+0x20f/0x220
[ 1101.319831] Modules linked in: ipheth usbmon nvidia_drm(PO) nvidia_modeset(PO) nvidia(PO) iwlmvm mac80211 iwlwifi btusb btrtl btbcm btintel qmi_wwan bluetooth cfg80211 ecdh_generic thinkpad_acpi rfkill [last unloaded: ipheth]
[ 1101.319861] CPU: 0 PID: 0 Comm: swapper/0 Tainted: P O 4.13.12.1 #1
[ 1101.319864] Hardware name: LENOVO 20ENCTO1WW/20ENCTO1WW, BIOS N1EET62W (1.35 ) 11/10/2016
[ 1101.319867] task: ffffffff81e11500 task.stack: ffffffff81e00000
[ 1101.319873] RIP: 0010:dev_watchdog+0x20f/0x220
[ 1101.319876] RSP: 0018:ffff8810a3c03e98 EFLAGS: 00010292
[ 1101.319880] RAX: 000000000000003a RBX: 0000000000000000 RCX: 0000000000000000
[ 1101.319883] RDX: ffff8810a3c15c48 RSI: ffffffff81ccbfc2 RDI: 00000000ffffffff
[ 1101.319886] RBP: ffff880c04ebc41c R08: 0000000000000000 R09: 0000000000000379
[ 1101.319889] R10: 00000100696589d0 R11: 0000000000000378 R12: ffff880c04ebc000
[ 1101.319892] R13: 0000000000000000 R14: 0000000000000001 R15: ffff880c2865fc80
[ 1101.319896] FS: 0000000000000000(0000) GS:ffff8810a3c00000(0000) knlGS:0000000000000000
[ 1101.319899] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1101.319902] CR2: 00007f3ff24ac000 CR3: 0000000001e0a000 CR4: 00000000003406f0
[ 1101.319905] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1101.319908] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1101.319910] Call Trace:
[ 1101.319914] <IRQ>
[ 1101.319921] ? dev_graft_qdisc+0x70/0x70
[ 1101.319928] ? dev_graft_qdisc+0x70/0x70
[ 1101.319934] ? call_timer_fn+0x2e/0x170
[ 1101.319939] ? dev_graft_qdisc+0x70/0x70
[ 1101.319944] ? run_timer_softirq+0x1ea/0x440
[ 1101.319951] ? timerqueue_add+0x54/0x80
[ 1101.319956] ? enqueue_hrtimer+0x38/0xa0
[ 1101.319963] ? __do_softirq+0xed/0x2e7
[ 1101.319970] ? irq_exit+0xb4/0xc0
[ 1101.319976] ? smp_apic_timer_interrupt+0x39/0x50
[ 1101.319981] ? apic_timer_interrupt+0x8c/0xa0
[ 1101.319983] </IRQ>
[ 1101.319992] ? cpuidle_enter_state+0xfa/0x2a0
[ 1101.319999] ? do_idle+0x1a3/0x1f0
[ 1101.320004] ? cpu_startup_entry+0x5f/0x70
[ 1101.320011] ? start_kernel+0x444/0x44c
[ 1101.320017] ? early_idt_handler_array+0x120/0x120
[ 1101.320023] ? x86_64_start_kernel+0x145/0x154
[ 1101.320028] ? secondary_startup_64+0x9f/0x9f
[ 1101.320033] Code: 20 04 00 00 eb 9f 4c 89 e7 c6 05 59 44 71 00 01 e8 a7 df fd ff 89 d9 4c 89 e6 48 c7 c7 70 b7 cd 81 48 89 c2 31 c0 e8 97 64 90 ff <0f> ff eb bf 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00
[ 1101.320103] ---[ end trace 0cc4d251e2b57080 ]---
[ 1101.320110] ipheth 1-5:4.2: ipheth_tx_timeout: TX timeout
The last message "TX timeout" is repeated every 5 seconds until trust is
established or the device is disconnected, filling up dmesg.
The proposed patch eliminates the problem by, upon connection, keeping the
TX queue and carrier disabled until a packet is first received from the iOS
device. This is reflected by the confirmed_pairing variable in the device
structure. Only after at least one packet has been received from the iOS
device, the transmit queue and carrier are brought up during the periodic
device poll in ipheth_carrier_set. Because the iOS device will always send
a packet immediately upon trust being established, this should not delay
the interface becoming useable. To prevent failed UBRs in
ipheth_rcvbulk_callback from perpetually re-enabling the queue if it was
disabled, a new check is added so only successful transfers re-enable the
queue, whereas failed transfers only trigger an immediate poll.
This has the added benefit of removing the periodic control requests to the
iOS device until trust has been established and thus should reduce wakeup
events on both the host and the iOS device.
Signed-off-by: Alexander Kappner <agk@godking.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple cases of overlapping changes in the packet scheduler.
Must easier to resolve this time.
Which probably means that I screwed it up somehow.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit baedf68a06.
There is an updated version of this fix which covers
the problem more thoroughly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting dev->hard_mtu to 0 will cause a divide error in
usbnet_probe. Protect against devices with bogus CDC Ethernet
functional descriptors by ignoring a zero wMaxSegmentSize.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer dev is being assigned but is never used, hence it is
redundant and can be removed. Cleans up clang warning:
drivers/net/usb/hso.c:2280:2: warning: Value stored to 'dev' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Huawei ME906 (12d1:15c1) comes with a standard ECM interface that
requires management via AT commands sent over one of the control TTYs
(e.g. connected with AT^NDISDUP).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
This product is named 'TP-LINK USB 3.0 Gigabit Ethernet Network
Adapter (Model No.is UE300)'. It uses chip RTL8153 and works with
driver drivers/net/usb/r8152.c
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: "Bjørn Mork" <bjorn@mork.no>
Cc: "Stefan Brüns" <stefan.bruens@rwth-aachen.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Since the callback is called from
both a timer and a tasklet, adjust the tasklet to pass the timer address
too. When tasklets have their .data field removed, this can be refactored
to call a central function after resolving the correct container_of() for a
separate callback function for timer and tasklet.
Cc: Oliver Neukum <oneukum@suse.com>
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The u-blox TOBY-L2 is a LTE Cat 4 module with HSPA+ and 2G fallback.
This module allows switching to different USB profiles with the
'AT+UUSBCONF' command, and provides a ECM network interface when the
'AT+UUSBCONF=2' profile is selected.
The u-blox SARA-U2 is a HSPA module with 2G fallback. The default USB
configuration includes a ECM network interface.
Both these modules are controlled via AT commands through one of the
TTYs exposed. Connecting these modules may be done just by activating
the desired PDP context with 'AT+CGACT=1,<cid>' and then running DHCP
on the ECM interface.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack arg to netdev_upper_dev_link and netdev_master_upper_dev_link
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat the ef/04/01 interface class/subclass/protocol combination used
by the Novatel Verizon USB730L (1410:9030) as a possible RNDIS
interface.
T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 3
P: Vendor=1410 ProdID=9030 Rev=03.10
S: Manufacturer=Novatel Wireless
S: Product=MiFi USB730L
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
I: If#= 2 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
Once the network interface is brought up, the user just needs to run a
DHCP client to get IP address and routing setup.
As a side note, other Novatel Verizon USB730L models with the same
vid:pid end up exposing a standard ECM interface which doesn't require
any other kernel update to make it work.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This linksys dongle by default comes up in cdc_ether mode.
This patch allows r8152 to claim the device:
Bus 002 Device 002: ID 13b1:0041 Linksys
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no one which would invokes the function skb_header_release.
So just remove it now.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use default value of auto duplex and auto speed values loaded
from EEPROM/OTP after reset. The LAN78xx allows platform
configurations to be loaded from EEPROM/OTP.
Ex: When external phy is connected, the MAC can be configured to
have correct auto speed, auto duplex, auto polarity configured
from the EEPROM/OTP.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow EEPROM write for less than MAX_EEPROM_SIZE
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for eeprom read/write when device auto suspend
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure pause time to 0xffff when tx flow control enabled
Set pause time to 0xffff in the pause frame to indicate the
partner to stop sending the packets. When RX buffer frees up,
the device sends pause frame with pause time zero for partner to
resume transmission.
Fixes: 2f7ca802bd ("Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The u-blox TOBY-L4 is a LTE Advanced (Cat 6) module with HSPA+ and 2G
fallback.
Unlike the TOBY-L2, this module has one single USB layout and exposes
several TTYs for control and a NCM interface for data. Connecting this
module may be done just by activating the desired PDP context with
'AT+CGACT=1,<cid>' and then running DHCP on the NCM interface.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
