Commit Graph

19877 Commits

Author SHA1 Message Date
Linus Torvalds
4a89452e70 Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
 "Two clocksource driver fixes, and an idle loop RCU warning fix"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/sun5i: Fix cpufreq interaction with sched_clock()
  clocksource/drivers: Fix various !CONFIG_HAS_IOMEM build errors
  timers/tick/broadcast-hrtimer: Fix suspicious RCU usage in idle loop
2015-03-28 11:21:23 -07:00
Linus Torvalds
19dba4f3e9 Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
 "A single sched/rt corner case fix for RLIMIT_RTIME correctness"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix RLIMIT_RTTIME when PI-boosting to RT
2015-03-28 11:17:32 -07:00
Linus Torvalds
ee9b63dd0f Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Ingo Molnar:
 "A perf kernel side fix for a fuzzer triggered lockup"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix irq_work 'tail' recursion
2015-03-28 11:12:08 -07:00
Linus Torvalds
0fa7271a8a Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
 "A module unload lockdep race fix"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  lockdep: Fix the module unload key range freeing logic
2015-03-28 11:05:03 -07:00
Mel Gorman
074c238177 mm: numa: slow PTE scan rate if migration failures occur
Dave Chinner reported the following on https://lkml.org/lkml/2015/3/1/226

  Across the board the 4.0-rc1 numbers are much slower, and the degradation
  is far worse when using the large memory footprint configs. Perf points
  straight at the cause - this is from 4.0-rc1 on the "-o bhash=101073" config:

   -   56.07%    56.07%  [kernel]            [k] default_send_IPI_mask_sequence_phys
      - default_send_IPI_mask_sequence_phys
         - 99.99% physflat_send_IPI_mask
            - 99.37% native_send_call_func_ipi
                 smp_call_function_many
               - native_flush_tlb_others
                  - 99.85% flush_tlb_page
                       ptep_clear_flush
                       try_to_unmap_one
                       rmap_walk
                       try_to_unmap
                       migrate_pages
                       migrate_misplaced_page
                     - handle_mm_fault
                        - 99.73% __do_page_fault
                             trace_do_page_fault
                             do_async_page_fault
                           + async_page_fault
              0.63% native_send_call_func_single_ipi
                 generic_exec_single
                 smp_call_function_single

This is showing excessive migration activity even though excessive
migrations are meant to get throttled.  Normally, the scan rate is tuned
on a per-task basis depending on the locality of faults.  However, if
migrations fail for any reason then the PTE scanner may scan faster if
the faults continue to be remote.  This means there is higher system CPU
overhead and fault trapping at exactly the time we know that migrations
cannot happen.  This patch tracks when migration failures occur and
slows the PTE scanner.

Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Dave Chinner <david@fromorbit.com>
Tested-by: Dave Chinner <david@fromorbit.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-03-25 16:20:31 -07:00
Preeti U Murthy
a127d2bcf1 timers/tick/broadcast-hrtimer: Fix suspicious RCU usage in idle loop
The hrtimer mode of broadcast queues hrtimers in the idle entry
path so as to wakeup cpus in deep idle states. The associated
call graph is :

	cpuidle_idle_call()
	|____ clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, ....))
	     |_____tick_broadcast_set_event()
		   |____clockevents_program_event()
			|____bc_set_next()

The hrtimer_{start/cancel} functions call into tracing which uses RCU.
But it is not legal to call into RCU in cpuidle because it is one of the
quiescent states. Hence protect this region with RCU_NONIDLE which informs
RCU that the cpu is momentarily non-idle.

As an aside it is helpful to point out that the clock event device that is
programmed here is not a per-cpu clock device; it is a
pseudo clock device, used by the broadcast framework alone.
The per-cpu clock device programming never goes through bc_set_next().

Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: linuxppc-dev@ozlabs.org
Cc: mpe@ellerman.id.au
Cc: tglx@linutronix.de
Link: http://lkml.kernel.org/r/20150318104705.17763.56668.stgit@preeti.in.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2015-03-23 10:50:05 +01:00
Peter Zijlstra
35a9393c95 lockdep: Fix the module unload key range freeing logic
Module unload calls lockdep_free_key_range(), which removes entries
from the data structures. Most of the lockdep code OTOH assumes the
data structures are append only; in specific see the comments in
add_lock_to_list() and look_up_lock_class().

Clearly this has only worked by accident; make it work proper. The
actual scenario to make it go boom would involve the memory freed by
the module unlock being re-allocated and re-used for a lock inside of
a rcu-sched grace period. This is a very unlikely scenario, still
better plug the hole.

Use RCU list iteration in all places and ammend the comments.

Change lockdep_free_key_range() to issue a sync_sched() between
removal from the lists and returning -- which results in the memory
being freed. Further ensure the callers are placed correctly and
comment the requirements.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Tsyvarev <tsyvarev@ispras.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2015-03-23 10:49:07 +01:00
Brian Silverman
746db9443e sched: Fix RLIMIT_RTTIME when PI-boosting to RT
When non-realtime tasks get priority-inheritance boosted to a realtime
scheduling class, RLIMIT_RTTIME starts to apply to them. However, the
counter used for checking this (the same one used for SCHED_RR
timeslices) was not getting reset. This meant that tasks running with a
non-realtime scheduling class which are repeatedly boosted to a realtime
one, but never block while they are running realtime, eventually hit the
timeout without ever running for a time over the limit. This patch
resets the realtime timeslice counter when un-PI-boosting from an RT to
a non-RT scheduling class.

I have some test code with two threads and a shared PTHREAD_PRIO_INHERIT
mutex which induces priority boosting and spins while boosted that gets
killed by a SIGXCPU on non-fixed kernels but doesn't with this patch
applied. It happens much faster with a CONFIG_PREEMPT_RT kernel, and
does happen eventually with PREEMPT_VOLUNTARY kernels.

Signed-off-by: Brian Silverman <brian@peloton-tech.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: austin@peloton-tech.com
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1424305436-6716-1-git-send-email-brian@peloton-tech.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2015-03-23 10:47:55 +01:00
Peter Zijlstra
d525211f9d perf: Fix irq_work 'tail' recursion
Vince reported a watchdog lockup like:

	[<ffffffff8115e114>] perf_tp_event+0xc4/0x210
	[<ffffffff810b4f8a>] perf_trace_lock+0x12a/0x160
	[<ffffffff810b7f10>] lock_release+0x130/0x260
	[<ffffffff816c7474>] _raw_spin_unlock_irqrestore+0x24/0x40
	[<ffffffff8107bb4d>] do_send_sig_info+0x5d/0x80
	[<ffffffff811f69df>] send_sigio_to_task+0x12f/0x1a0
	[<ffffffff811f71ce>] send_sigio+0xae/0x100
	[<ffffffff811f72b7>] kill_fasync+0x97/0xf0
	[<ffffffff8115d0b4>] perf_event_wakeup+0xd4/0xf0
	[<ffffffff8115d103>] perf_pending_event+0x33/0x60
	[<ffffffff8114e3fc>] irq_work_run_list+0x4c/0x80
	[<ffffffff8114e448>] irq_work_run+0x18/0x40
	[<ffffffff810196af>] smp_trace_irq_work_interrupt+0x3f/0xc0
	[<ffffffff816c99bd>] trace_irq_work_interrupt+0x6d/0x80

Which is caused by an irq_work generating new irq_work and therefore
not allowing forward progress.

This happens because processing the perf irq_work triggers another
perf event (tracepoint stuff) which in turn generates an irq_work ad
infinitum.

Avoid this by raising the recursion counter in the irq_work -- which
effectively disables all software events (including tracepoints) from
actually triggering again.

Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Tested-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20150219170311.GH21418@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2015-03-23 10:46:32 +01:00
Linus Torvalds
da11508eb0 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching
Pull livepatching fix from Jiri Kosina:

 - fix for potential race with module loading, from Petr Mladek.

   The race is very unlikely to be seen in real world and has been found
   by code inspection, but should be fixed for 4.0 anyway.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
  livepatch: Fix subtle race with coming and going modules
2015-03-18 10:46:39 -07:00
Linus Torvalds
13326e5a62 Merge branches 'perf-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf and timer fixes from Ingo Molnar:
 "Two small perf fixes:
   - kernel side context leak fix
   - tooling crash fix

  And two clocksource driver fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix context leak in put_event()
  perf annotate: Fix fallback to unparsed disassembler line

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clockevents: sun5i: Fix setup_irq init sequence
  clocksource: efm32: Fix a NULL pointer dereference
2015-03-17 13:22:29 -07:00
Petr Mladek
8cb2c2dc47 livepatch: Fix subtle race with coming and going modules
There is a notifier that handles live patches for coming and going modules.
It takes klp_mutex lock to avoid races with coming and going patches but
it does not keep the lock all the time. Therefore the following races are
possible:

  1. The notifier is called sometime in STATE_MODULE_COMING. The module
     is visible by find_module() in this state all the time. It means that
     new patch can be registered and enabled even before the notifier is
     called. It might create wrong order of stacked patches, see below
     for an example.

   2. New patch could still see the module in the GOING state even after
      the notifier has been called. It will try to initialize the related
      object structures but the module could disappear at any time. There
      will stay mess in the structures. It might even cause an invalid
      memory access.

This patch solves the problem by adding a boolean variable into struct module.
The value is true after the coming and before the going handler is called.
New patches need to be applied when the value is true and they need to ignore
the module when the value is false.

Note that we need to know state of all modules on the system. The races are
related to new patches. Therefore we do not know what modules will get
patched.

Also note that we could not simply ignore going modules. The code from the
module could be called even in the GOING state until mod->exit() finishes.
If we start supporting patches with semantic changes between function
calls, we need to apply new patches to any still usable code.
See below for an example.

Finally note that the patch solves only the situation when a new patch is
registered. There are no such problems when the patch is being removed.
It does not matter who disable the patch first, whether the normal
disable_patch() or the module notifier. There is nothing to do
once the patch is disabled.

Alternative solutions:
======================

+ reject new patches when a patched module is coming or going; this is ugly

+ wait with adding new patch until the module leaves the COMING and GOING
  states; this might be dangerous and complicated; we would need to release
  kgr_lock in the middle of the patch registration to avoid a deadlock
  with the coming and going handlers; also we might need a waitqueue for
  each module which seems to be even bigger overhead than the boolean

+ stop modules from entering COMING and GOING states; wait until modules
  leave these states when they are already there; looks complicated; we would
  need to ignore the module that asked to stop the others to avoid a deadlock;
  also it is unclear what to do when two modules asked to stop others and
  both are in COMING state (situation when two new patches are applied)

+ always register/enable new patches and fix up the potential mess (registered
  patches order) in klp_module_init(); this is nasty and prone to regressions
  in the future development

+ add another MODULE_STATE where the kallsyms are visible but the module is not
  used yet; this looks too complex; the module states are checked on "many"
  locations

Example of patch stacking breakage:
===================================

The notifier could _not_ _simply_ ignore already initialized module objects.
For example, let's have three patches (P1, P2, P3) for functions a() and b()
where a() is from vmcore and b() is from a module M. Something like:

	a()	b()
P1	a1()	b1()
P2	a2()	b2()
P3	a3()	b3(3)

If you load the module M after all patches are registered and enabled.
The ftrace ops for function a() and b() has listed the functions in this
order:

	ops_a->func_stack -> list(a3,a2,a1)
	ops_b->func_stack -> list(b3,b2,b1)

, so the pointer to b3() is the first and will be used.

Then you might have the following scenario. Let's start with state when patches
P1 and P2 are registered and enabled but the module M is not loaded. Then ftrace
ops for b() does not exist. Then we get into the following race:

CPU0					CPU1

load_module(M)

  complete_formation()

  mod->state = MODULE_STATE_COMING;
  mutex_unlock(&module_mutex);

					klp_register_patch(P3);
					klp_enable_patch(P3);

					# STATE 1

  klp_module_notify(M)
    klp_module_notify_coming(P1);
    klp_module_notify_coming(P2);
    klp_module_notify_coming(P3);

					# STATE 2

The ftrace ops for a() and b() then looks:

  STATE1:

	ops_a->func_stack -> list(a3,a2,a1);
	ops_b->func_stack -> list(b3);

  STATE2:
	ops_a->func_stack -> list(a3,a2,a1);
	ops_b->func_stack -> list(b2,b1,b3);

therefore, b2() is used for the module but a3() is used for vmcore
because they were the last added.

Example of the race with going modules:
=======================================

CPU0					CPU1

delete_module()  #SYSCALL

   try_stop_module()
     mod->state = MODULE_STATE_GOING;

   mutex_unlock(&module_mutex);

					klp_register_patch()
					klp_enable_patch()

					#save place to switch universe

					b()     # from module that is going
					  a()   # from core (patched)

   mod->exit();

Note that the function b() can be called until we call mod->exit().

If we do not apply patch against b() because it is in MODULE_STATE_GOING,
it will call patched a() with modified semantic and things might get wrong.

[jpoimboe@redhat.com: use one boolean instead of two]
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-17 10:31:54 +01:00
Leon Yu
d415a7f1c1 perf: Fix context leak in put_event()
Commit:

  a83fe28e2e ("perf: Fix put_event() ctx lock")

changed the locking logic in put_event() by replacing mutex_lock_nested()
with perf_event_ctx_lock_nested(), but didn't fix the subsequent
mutex_unlock() with a correct counterpart, perf_event_ctx_unlock().

Contexts are thus leaked as a result of incremented refcount
in perf_event_ctx_lock_nested().

Signed-off-by: Leon Yu <chianglungyu@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Fixes: a83fe28e2e ("perf: Fix put_event() ctx lock")
Link: http://lkml.kernel.org/r/1424954613-5034-1-git-send-email-chianglungyu@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2015-03-13 10:02:18 +01:00
Andrey Ryabinin
a5af5aa8b6 kasan, module, vmalloc: rework shadow allocation for modules
Current approach in handling shadow memory for modules is broken.

Shadow memory could be freed only after memory shadow corresponds it is no
longer used.  vfree() called from interrupt context could use memory its
freeing to store 'struct llist_node' in it:

    void vfree(const void *addr)
    {
    ...
        if (unlikely(in_interrupt())) {
            struct vfree_deferred *p = this_cpu_ptr(&vfree_deferred);
            if (llist_add((struct llist_node *)addr, &p->list))
                    schedule_work(&p->wq);

Later this list node used in free_work() which actually frees memory.
Currently module_memfree() called in interrupt context will free shadow
before freeing module's memory which could provoke kernel crash.

So shadow memory should be freed after module's memory.  However, such
deallocation order could race with kasan_module_alloc() in module_alloc().

Free shadow right before releasing vm area.  At this point vfree()'d
memory is not used anymore and yet not available for other allocations.
New VM_KASAN flag used to indicate that vm area has dynamically allocated
shadow memory so kasan frees shadow only if it was previously allocated.

Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-03-12 18:46:08 -07:00
Linus Torvalds
e7901af143 This includes fixes for seq_buf_bprintf() truncation issue. It also
contains fixes to ftrace when /proc/sys/kernel/ftrace_enabled and
 function tracing are started. Doing the following causes some issues:
 
  # echo 0 > /proc/sys/kernel/ftrace_enabled
  # echo function_graph > /sys/kernel/debug/tracing/current_tracer
  # echo 1 > /proc/sys/kernel/ftrace_enabled
  # echo nop > /sys/kernel/debug/tracing/current_tracer
  # echo function_graph > /sys/kernel/debug/tracing/current_tracer
 
 As well as with function tracing too. Pratyush Anand first reported
 this issue to me and supplied a patch. When I tested this on my x86
 test box, it caused thousands of backtraces and warnings to appear in
 dmesg, which also caused a denial of service (a warning for every
 function that was listed). I applied Pratyush's patch but it did not
 fix the issue for me. I looked into it and found a slight problem
 with trampoline accounting. I fixed it and sent Pratyush a patch, but
 he said that it did not fix the issue for him.
 
 I later learned tha Pratyush was using an ARM64 server, and when I tested
 on my ARM board, I was able to reproduce the same issue as Pratyush.
 After applying his patch, it fixed the problem. The above test uncovered
 two different bugs, one in x86 and one in ARM and ARM64. As this looked
 like it would affect PowerPC, I tested it on my PPC64 box. It too broke,
 but neither the patch that fixed ARM or x86 fixed this box (the changes
 were all in generic code!). The above test, uncovered two more bugs that
 affected PowerPC. Again, the changes were only done to generic code.
 It's the way the arch code expected things to be done that was different
 between the archs. Some where more sensitive than others.
 
 The rest of this series fixes the PPC bugs as well.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJU/cQSAAoJEEjnJuOKh9lde9sH/1MAPq+6jr7YaEFru0GKajE9
 rVHjw8rde/I4tN2UxIVk+Qm6pXRZYpv3OKxHT48EHzkvgm++voioykpJP4IEVrP5
 mEDuIcYe28csE2nV5u5Q9kwnZoC86TQW5nVV6zB1Gx/3IEzA8Z046jAov40Jya0y
 zqHc/U43JeeVIDIOkwjzbH6OaFEDP13FkF3TO502WJhJLqMo+kPOalIgv0eauKzy
 lVCQBSC4WS3rVsgW4W3dSrEBaUxbJxgunjxOuV2DwHj5eghHq0M2MKeIUxBz0PuN
 wnhTrpf5cAfshTvYHxKlE0uItdyYfVb7UChAD5zTbBL4kMUFhpb183zVKH8K8kU=
 =8R8y
 -----END PGP SIGNATURE-----

Merge tag 'trace-fixes-v4.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull seq-buf/ftrace fixes from Steven Rostedt:
 "This includes fixes for seq_buf_bprintf() truncation issue.  It also
  contains fixes to ftrace when /proc/sys/kernel/ftrace_enabled and
  function tracing are started.  Doing the following causes some issues:

    # echo 0 > /proc/sys/kernel/ftrace_enabled
    # echo function_graph > /sys/kernel/debug/tracing/current_tracer
    # echo 1 > /proc/sys/kernel/ftrace_enabled
    # echo nop > /sys/kernel/debug/tracing/current_tracer
    # echo function_graph > /sys/kernel/debug/tracing/current_tracer

  As well as with function tracing too.  Pratyush Anand first reported
  this issue to me and supplied a patch.  When I tested this on my x86
  test box, it caused thousands of backtraces and warnings to appear in
  dmesg, which also caused a denial of service (a warning for every
  function that was listed).  I applied Pratyush's patch but it did not
  fix the issue for me.  I looked into it and found a slight problem
  with trampoline accounting.  I fixed it and sent Pratyush a patch, but
  he said that it did not fix the issue for him.

  I later learned tha Pratyush was using an ARM64 server, and when I
  tested on my ARM board, I was able to reproduce the same issue as
  Pratyush.  After applying his patch, it fixed the problem.  The above
  test uncovered two different bugs, one in x86 and one in ARM and
  ARM64.  As this looked like it would affect PowerPC, I tested it on my
  PPC64 box.  It too broke, but neither the patch that fixed ARM or x86
  fixed this box (the changes were all in generic code!).  The above
  test, uncovered two more bugs that affected PowerPC.  Again, the
  changes were only done to generic code.  It's the way the arch code
  expected things to be done that was different between the archs.  Some
  where more sensitive than others.

  The rest of this series fixes the PPC bugs as well"

* tag 'trace-fixes-v4.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Fix ftrace enable ordering of sysctl ftrace_enabled
  ftrace: Fix en(dis)able graph caller when en(dis)abling record via sysctl
  ftrace: Clear REGS_EN and TRAMP_EN flags on disabling record via sysctl
  seq_buf: Fix seq_buf_bprintf() truncation
  seq_buf: Fix seq_buf_vprintf() truncation
2015-03-09 18:44:06 -07:00
Linus Torvalds
c0e99a71bd Merge branch 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
 "The cgroup iteration update two years ago and the recent cpuset
  restructuring introduced regressions in subset of cpuset
  configurations.  Three patches to fix them.

  All are marked for -stable"

* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cpuset: Fix cpuset sched_relax_domain_level
  cpuset: fix a warning when clearing configured masks in old hierarchy
  cpuset: initialize effective masks when clone_children is enabled
2015-03-09 17:30:09 -07:00
Linus Torvalds
b695f31f4e Merge branch 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
 "One fix patch for a subtle livelock condition which can happen on
  PREEMPT_NONE kernels involving two racing cancel_work calls.  Whoever
  comes in the second has to wait for the previous one to finish.  This
  was implemented by making the later one block for the same condition
  that the former would be (work item completion) and then loop and
  retest; unfortunately, depending on the wake up order, the later one
  could lock out the former one to finish by busy looping on the cpu.

  This is fixed by implementing explicit wait mechanism.  Work item
  might not belong anywhere at this point and there's remote possibility
  of thundering herd problem.  I originally tried to use bit_waitqueue
  but it didn't work for static work items on modules.  It's currently
  using single wait queue with filtering wake up function and exclusive
  wakeup.  If this ever becomes a problem, which is not very likely, we
  can try to figure out a way to piggy back on bit_waitqueue"

* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: fix hang involving racing cancel[_delayed]_work_sync()'s for PREEMPT_NONE
2015-03-09 17:00:54 -07:00
Steven Rostedt (Red Hat)
524a386825 ftrace: Fix ftrace enable ordering of sysctl ftrace_enabled
Some archs (specifically PowerPC), are sensitive with the ordering of
the enabling of the calls to function tracing and setting of the
function to use to be traced.

That is, update_ftrace_function() sets what function the ftrace_caller
trampoline should call. Some archs require this to be set before
calling ftrace_run_update_code().

Another bug was discovered, that ftrace_startup_sysctl() called
ftrace_run_update_code() directly. If the function the ftrace_caller
trampoline changes, then it will not be updated. Instead a call
to ftrace_startup_enable() should be called because it tests to see
if the callback changed since the code was disabled, and will
tell the arch to update appropriately. Most archs do not need this
notification, but PowerPC does.

The problem could be seen by the following commands:

 # echo 0 > /proc/sys/kernel/ftrace_enabled
 # echo function > /sys/kernel/debug/tracing/current_tracer
 # echo 1 > /proc/sys/kernel/ftrace_enabled
 # cat /sys/kernel/debug/tracing/trace

The trace will show that function tracing was not active.

Cc: stable@vger.kernel.org # 2.6.27+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2015-03-09 10:55:34 -04:00
Pratyush Anand
1619dc3f8f ftrace: Fix en(dis)able graph caller when en(dis)abling record via sysctl
When ftrace is enabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_START_FUNC_RET command to ftrace_run_update_code(). Similarly, when
ftrace is disabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_STOP_FUNC_RET command to ftrace_run_update_code().

Consider the following situation.

 # echo 0 > /proc/sys/kernel/ftrace_enabled

After this ftrace_enabled = 0.

 # echo function_graph > /sys/kernel/debug/tracing/current_tracer

Since ftrace_enabled = 0, ftrace_enable_ftrace_graph_caller() is never
called.

 # echo 1 > /proc/sys/kernel/ftrace_enabled

Now ftrace_enabled will be set to true, but still
ftrace_enable_ftrace_graph_caller() will not be called, which is not
desired.

Further if we execute the following after this:
  # echo nop > /sys/kernel/debug/tracing/current_tracer

Now since ftrace_enabled is set it will call
ftrace_disable_ftrace_graph_caller(), which causes a kernel warning on
the ARM platform.

On the ARM platform, when ftrace_enable_ftrace_graph_caller() is called,
it checks whether the old instruction is a nop or not. If it's not a nop,
then it returns an error. If it is a nop then it replaces instruction at
that address with a branch to ftrace_graph_caller.
ftrace_disable_ftrace_graph_caller() behaves just the opposite. Therefore,
if generic ftrace code ever calls either ftrace_enable_ftrace_graph_caller()
or ftrace_disable_ftrace_graph_caller() consecutively two times in a row,
then it will return an error, which will cause the generic ftrace code to
raise a warning.

Note, x86 does not have an issue with this because the architecture
specific code for ftrace_enable_ftrace_graph_caller() and
ftrace_disable_ftrace_graph_caller() does not check the previous state,
and calling either of these functions twice in a row has no ill effect.

Link: http://lkml.kernel.org/r/e4fbe64cdac0dd0e86a3bf914b0f83c0b419f146.1425666454.git.panand@redhat.com

Cc: stable@vger.kernel.org # 2.6.31+
Signed-off-by: Pratyush Anand <panand@redhat.com>
[
  removed extra if (ftrace_start_up) and defined ftrace_graph_active as 0
  if CONFIG_FUNCTION_GRAPH_TRACER is not set.
]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2015-03-09 10:50:51 -04:00
Steven Rostedt (Red Hat)
b24d443b8f ftrace: Clear REGS_EN and TRAMP_EN flags on disabling record via sysctl
When /proc/sys/kernel/ftrace_enabled is set to zero, all function
tracing is disabled. But the records that represent the functions
still hold information about the ftrace_ops that are hooked to them.

ftrace_ops may request "REGS" (have a full set of pt_regs passed to
the callback), or "TRAMP" (the ops has its own trampoline to use).
When the record is updated to represent the state of the ops hooked
to it, it sets "REGS_EN" and/or "TRAMP_EN" to state that the callback
points to the correct trampoline (REGS has its own trampoline).

When ftrace_enabled is set to zero, all ftrace locations are a nop,
so they do not point to any trampoline. But the _EN flags are still
set. This can cause the accounting to go wrong when ftrace_enabled
is cleared and an ops that has a trampoline is registered or unregistered.

For example, the following will cause ftrace to crash:

 # echo function_graph > /sys/kernel/debug/tracing/current_tracer
 # echo 0 > /proc/sys/kernel/ftrace_enabled
 # echo nop > /sys/kernel/debug/tracing/current_tracer
 # echo 1 > /proc/sys/kernel/ftrace_enabled
 # echo function_graph > /sys/kernel/debug/tracing/current_tracer

As function_graph uses a trampoline, when ftrace_enabled is set to zero
the updates to the record are not done. When enabling function_graph
again, the record will still have the TRAMP_EN flag set, and it will
look for an op that has a trampoline other than the function_graph
ops, and fail to find one.

Cc: stable@vger.kernel.org # 3.17+
Reported-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2015-03-09 10:46:00 -04:00
Linus Torvalds
bbbce516bb TTY/Serial fixes for 4.0-rc3
Here are some tty and serial driver fixes for 4.0-rc3.
 
 Along with the atime fix that you know about, here are some other serial
 driver bugfixes as well.  Most notable is a wait_until_sent bugfix that
 was traced back to being around since before 2.6.12 that Johan has fixed
 up.
 
 All have been in linux-next successfully.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlT8RCYACgkQMUfUDdst+yk62QCgycxS4giC2hyRver3dyvaNR6g
 zYYAn2w0uRndW+AqP4Tls54isRz6owpF
 =gA2k
 -----END PGP SIGNATURE-----

Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial fixes from Greg KH:
 "Here are some tty and serial driver fixes for 4.0-rc3.

  Along with the atime fix that you know about, here are some other
  serial driver bugfixes as well.  Most notable is a wait_until_sent
  bugfix that was traced back to being around since before 2.6.12 that
  Johan has fixed up.

  All have been in linux-next successfully"

* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  TTY: fix tty_wait_until_sent maximum timeout
  TTY: fix tty_wait_until_sent on 64-bit machines
  USB: serial: fix infinite wait_until_sent timeout
  TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
  net: irda: fix wait_until_sent poll timeout
  serial: uapi: Declare all userspace-visible io types
  serial: core: Fix iotype userspace breakage
  serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
  console: Fix console name size mismatch
  tty: fix up atime/mtime mess, take four
  serial: 8250_dw: Fix get_mctrl behaviour
  serial:8250:8250_pci: delete unneeded quirk entries
  serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
  Change email address for 8250_pci
  serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
  Revert "tty/serial: of_serial: add DT alias ID handling"
2015-03-08 12:25:40 -07:00
Linus Torvalds
9aae0df6a3 arm64 and generic kernel/module.c (acked by Rusty) fixes for
CONFIG_DEBUG_SET_MODULE_RONX.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJU+tUEAAoJEGvWsS0AyF7xDtoP/R28n36wPcCcOXqDIPXefknH
 2+Xc7I6287UKWX/dufySrISCDHWPpCWw1siAVaTGdENn3qEfSnz04OlUj7rhJ61d
 BF9mUfU8CRbM9uYN7CwDYFvRniA19FwGXkeGeBOI6Cr70XuoOSDNfB8wnZpzifFO
 wRtnLr2IfuF7eojTXjh6biFb5zYIHgLv3eAGxDJf7shdUOF8Jp1/WxvXoXEZDOF2
 xypA6gbouquNTDZQqGWi/PD4bxr0/Xx9gaZ0vpB+Xby34VlA7gIQnAR3tgZegYFm
 iPFc/D0AIXTO3KpPCrZL7KDQksevSjM32cfiAM4v8OepDsCDBQLiOGFpBLSc6oSp
 aO2pbTKZYhFTLUbPkmV43w60LNNaum8MZZ0eGLW1hD7A5hNpBoaH/mD7jaClzn2o
 /pQ5VETOD72NEQMEV+701+Tq0vbX6y1ekmxpxNhdsEyxOb9MQdwiSbmeoj+4LBU0
 +FeYg+cYLTG5CUnoWKxvMms6wB4K6hdvZmALKFXtdi3bdIaaW+f40XlKFVivanwF
 dl0UWeXlBdpiy7rM0S8mn2SHyk1rAMPLv0IRLdj0aYthhzMbBNRFh9YoQtcbEN+r
 ufCsRhSFiw9ODesOK1YT0iaKGZ7H4NJOLDFCl9oDw84/aBnMrCz2uGy9M4Qb9pRa
 ZEQueee55zcxs05/4Q8j
 =zrIh
 -----END PGP SIGNATURE-----

Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux

Pull arm64 fixes from Catalin Marinas:
 "arm64 and generic kernel/module.c (acked by Rusty) fixes for
  CONFIG_DEBUG_SET_MODULE_RONX"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  kernel/module.c: Update debug alignment after symtable generation
  arm64: Don't use is_module_addr in setting page attributes
2015-03-07 11:31:17 -08:00
Peter Hurley
30a22c215a console: Fix console name size mismatch
commit 6ae9200f2c ("enlarge console.name") increased the storage
for the console name to 16 bytes, but not the corresponding
struct console_cmdline::name storage. Console names longer than
8 bytes cause read beyond end-of-string and failure to match
console; I'm not sure if there are other unexpected consequences.

Cc: <stable@vger.kernel.org> # 2.6.22+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-07 03:39:55 +01:00
Linus Torvalds
0d9b9c1674 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching
Pull livepatching fix from Jiri Kosina:
 "Fix an RCU unlock misplacement in live patching infrastructure, from
  Peter Zijlstra"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
  livepatch: fix RCU usage in klp_find_external_symbol()
2015-03-06 13:47:56 -08:00
Laura Abbott
168e47f2a6 kernel/module.c: Update debug alignment after symtable generation
When CONFIG_DEBUG_SET_MODULE_RONX is enabled, the sizes of
module sections are aligned up so appropriate permissions can
be applied. Adjusting for the symbol table may cause them to
become unaligned. Make sure to re-align the sizes afterward.

Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2015-03-06 12:04:22 +00:00
Rafael J. Wysocki
79d223646b Merge branch 'irq-pm'
* irq-pm:
  genirq / PM: describe IRQF_COND_SUSPEND
  tty: serial: atmel: rework interrupt and wakeup handling
  watchdog: at91sam9: request the irq with IRQF_NO_SUSPEND
  clk: at91: implement suspend/resume for the PMC irqchip
  rtc: at91rm9200: rework wakeup and interrupt handling
  rtc: at91sam9: rework wakeup and interrupt handling
  PM / wakeup: export pm_system_wakeup symbol
  genirq / PM: Add flag for shared NO_SUSPEND interrupt lines
  genirq / PM: better describe IRQF_NO_SUSPEND semantics
2015-03-06 01:29:05 +01:00
Rafael J. Wysocki
eef16e4362 Merge branch 'suspend-to-idle'
* suspend-to-idle:
  cpuidle / sleep: Use broadcast timer for states that stop local timer
  cpuidle: Clean up fallback handling in cpuidle_idle_call()
  cpuidle / sleep: Do sanity checks in cpuidle_enter_freeze() too
  idle / sleep: Avoid excessive disabling and enabling interrupts
2015-03-05 23:14:51 +01:00
Rafael J. Wysocki
ef2b22ac54 cpuidle / sleep: Use broadcast timer for states that stop local timer
Commit 3810631332 (PM / sleep: Re-implement suspend-to-idle handling)
overlooked the fact that entering some sufficiently deep idle states
by CPUs may cause their local timers to stop and in those cases it
is necessary to switch over to a broadcast timer prior to entering
the idle state.  If the cpuidle driver in use does not provide
the new ->enter_freeze callback for any of the idle states, that
problem affects suspend-to-idle too, but it is not taken into account
after the changes made by commit 3810631332.

Fix that by changing the definition of cpuidle_enter_freeze() and
re-arranging of the code in cpuidle_idle_call(), so the former does
not call cpuidle_enter() any more and the fallback case is handled
by cpuidle_idle_call() directly.

Fixes: 3810631332 (PM / sleep: Re-implement suspend-to-idle handling)
Reported-and-tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
2015-03-05 23:13:19 +01:00
Tejun Heo
8603e1b300 workqueue: fix hang involving racing cancel[_delayed]_work_sync()'s for PREEMPT_NONE
cancel[_delayed]_work_sync() are implemented using
__cancel_work_timer() which grabs the PENDING bit using
try_to_grab_pending() and then flushes the work item with PENDING set
to prevent the on-going execution of the work item from requeueing
itself.

try_to_grab_pending() can always grab PENDING bit without blocking
except when someone else is doing the above flushing during
cancelation.  In that case, try_to_grab_pending() returns -ENOENT.  In
this case, __cancel_work_timer() currently invokes flush_work().  The
assumption is that the completion of the work item is what the other
canceling task would be waiting for too and thus waiting for the same
condition and retrying should allow forward progress without excessive
busy looping

Unfortunately, this doesn't work if preemption is disabled or the
latter task has real time priority.  Let's say task A just got woken
up from flush_work() by the completion of the target work item.  If,
before task A starts executing, task B gets scheduled and invokes
__cancel_work_timer() on the same work item, its try_to_grab_pending()
will return -ENOENT as the work item is still being canceled by task A
and flush_work() will also immediately return false as the work item
is no longer executing.  This puts task B in a busy loop possibly
preventing task A from executing and clearing the canceling state on
the work item leading to a hang.

task A			task B			worker

						executing work
__cancel_work_timer()
  try_to_grab_pending()
  set work CANCELING
  flush_work()
    block for work completion
						completion, wakes up A
			__cancel_work_timer()
			while (forever) {
			  try_to_grab_pending()
			    -ENOENT as work is being canceled
			  flush_work()
			    false as work is no longer executing
			}

This patch removes the possible hang by updating __cancel_work_timer()
to explicitly wait for clearing of CANCELING rather than invoking
flush_work() after try_to_grab_pending() fails with -ENOENT.

Link: http://lkml.kernel.org/g/20150206171156.GA8942@axis.com

v3: bit_waitqueue() can't be used for work items defined in vmalloc
    area.  Switched to custom wake function which matches the target
    work item and exclusive wait and wakeup.

v2: v1 used wake_up() on bit_waitqueue() which leads to NULL deref if
    the target bit waitqueue has wait_bit_queue's on it.  Use
    DEFINE_WAIT_BIT() and __wake_up_bit() instead.  Reported by Tomeu
    Vizoso.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Rabin Vincent <rabin.vincent@axis.com>
Cc: Tomeu Vizoso <tomeu.vizoso@gmail.com>
Cc: stable@vger.kernel.org
Tested-by: Jesper Nilsson <jesper.nilsson@axis.com>
Tested-by: Rabin Vincent <rabin.vincent@axis.com>
2015-03-05 08:04:13 -05:00
Rafael J. Wysocki
17f4803420 genirq / PM: Add flag for shared NO_SUSPEND interrupt lines
It currently is required that all users of NO_SUSPEND interrupt
lines pass the IRQF_NO_SUSPEND flag when requesting the IRQ or the
WARN_ON_ONCE() in irq_pm_install_action() will trigger.  That is
done to warn about situations in which unprepared interrupt handlers
may be run unnecessarily for suspended devices and may attempt to
access those devices by mistake.  However, it may cause drivers
that have no technical reasons for using IRQF_NO_SUSPEND to set
that flag just because they happen to share the interrupt line
with something like a timer.

Moreover, the generic handling of wakeup interrupts introduced by
commit 9ce7a25849 (genirq: Simplify wakeup mechanism) only works
for IRQs without any NO_SUSPEND users, so the drivers of wakeup
devices needing to use shared NO_SUSPEND interrupt lines for
signaling system wakeup generally have to detect wakeup in their
interrupt handlers.  Thus if they happen to share an interrupt line
with a NO_SUSPEND user, they also need to request that their
interrupt handlers be run after suspend_device_irqs().

In both cases the reason for using IRQF_NO_SUSPEND is not because
the driver in question has a genuine need to run its interrupt
handler after suspend_device_irqs(), but because it happens to
share the line with some other NO_SUSPEND user.  Otherwise, the
driver would do without IRQF_NO_SUSPEND just fine.

To make it possible to specify that condition explicitly, introduce
a new IRQ action handler flag for shared IRQs, IRQF_COND_SUSPEND,
that, when set, will indicate to the IRQ core that the interrupt
user is generally fine with suspending the IRQ, but it also can
tolerate handler invocations after suspend_device_irqs() and, in
particular, it is capable of detecting system wakeup and triggering
it as appropriate from its interrupt handler.

That will allow us to work around a problem with a shared timer
interrupt line on at91 platforms.

Link: http://marc.info/?l=linux-kernel&m=142252777602084&w=2
Link: http://marc.info/?t=142252775300011&r=1&w=2
Link: https://lkml.org/lkml/2014/12/15/552
Reported-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
2015-03-04 21:42:19 +01:00
Peter Zijlstra
c064a0de1b livepatch: fix RCU usage in klp_find_external_symbol()
While one must hold RCU-sched (aka. preempt_disable) for find_symbol()
one must equally hold it over the use of the object returned.

The moment you release the RCU-sched read lock, the object can be dead
and gone.

[jkosina@suse.cz: change subject line to be aligned with other patches]
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Petr Mladek <pmladek@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-03 00:22:55 +01:00
Rafael J. Wysocki
dfcacc154f cpuidle: Clean up fallback handling in cpuidle_idle_call()
Move the fallback code path in cpuidle_idle_call() to the end of the
function to avoid jumping to a label in an if () branch.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-03-02 22:25:37 +01:00
Jason Low
283cb41f42 cpuset: Fix cpuset sched_relax_domain_level
The cpuset.sched_relax_domain_level can control how far we do
immediate load balancing on a system. However, it was found on recent
kernels that echo'ing a value into cpuset.sched_relax_domain_level
did not reduce any immediate load balancing.

The reason this occurred was because the update_domain_attr_tree() traversal
did not update for the "top_cpuset". This resulted in nothing being changed
when modifying the sched_relax_domain_level parameter.

This patch is able to address that problem by having update_domain_attr_tree()
allow updates for the root in the cpuset traversal.

Fixes: fc560a26ac ("cpuset: replace cpuset->stack_list with cpuset_for_each_descendant_pre()")
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Jason Low <jason.low2@hp.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Serge Hallyn <serge.hallyn@canonical.com>
2015-03-02 11:55:04 -05:00
Zefan Li
79063bffc8 cpuset: fix a warning when clearing configured masks in old hierarchy
When we clear cpuset.cpus, cpuset.effective_cpus won't be cleared:

  # mount -t cgroup -o cpuset xxx /mnt
  # mkdir /mnt/tmp
  # echo 0 > /mnt/tmp/cpuset.cpus
  # echo > /mnt/tmp/cpuset.cpus
  # cat cpuset.cpus

  # cat cpuset.effective_cpus
  0-15

And a kernel warning in update_cpumasks_hier() is triggered:

 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 4028 at kernel/cpuset.c:894 update_cpumasks_hier+0x471/0x650()

Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Serge Hallyn <serge.hallyn@canonical.com>
2015-03-02 11:55:04 -05:00
Zefan Li
790317e1b2 cpuset: initialize effective masks when clone_children is enabled
If clone_children is enabled, effective masks won't be initialized
due to the bug:

  # mount -t cgroup -o cpuset xxx /mnt
  # echo 1 > cgroup.clone_children
  # mkdir /mnt/tmp
  # cat /mnt/tmp/
  # cat cpuset.effective_cpus

  # cat cpuset.cpus
  0-15

And then this cpuset won't constrain the tasks in it.

Either the bug or the fix has no effect on unified hierarchy, as
there's no clone_chidren flag there any more.

Reported-by: Christian Brauner <christianvanbrauner@gmail.com>
Reported-by: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Serge Hallyn <serge.hallyn@canonical.com>
2015-03-02 11:55:04 -05:00
Linus Torvalds
2ea51b884b Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
 "An rtmutex deadlock path fixlet"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/rtmutex: Set state back to running on error
2015-03-01 11:27:04 -08:00
Sebastian Andrzej Siewior
9d3e2d02f5 locking/rtmutex: Set state back to running on error
The "usual" path is:

 - rt_mutex_slowlock()
 - set_current_state()
 - task_blocks_on_rt_mutex() (ret 0)
 - __rt_mutex_slowlock()
   - sleep or not but do return with __set_current_state(TASK_RUNNING)
 - back to caller.

In the early error case where task_blocks_on_rt_mutex() return
-EDEADLK we never change the task's state back to RUNNING. I
assume this is intended. Without this change after ww_mutex
using rt_mutex the selftest passes but later I get plenty of:

  | bad: scheduling from the idle thread!

backtraces.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: afffc6c180 ("locking/rtmutex: Optimize setting task running after being blocked")
Link: http://lkml.kernel.org/r/1425056229-22326-4-git-send-email-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2015-03-01 09:45:06 +01:00
Rafael J. Wysocki
01e04f466e idle / sleep: Avoid excessive disabling and enabling interrupts
Disabling interrupts at the end of cpuidle_enter_freeze() is not
useful, because its caller, cpuidle_idle_call(), re-enables them
right away after invoking it.

To avoid that unnecessary back and forth dance with interrupts,
make cpuidle_enter_freeze() enable interrupts after calling
enter_freeze_proper() and drop the local_irq_disable() at its
end, so that all of the code paths in it end up with interrupts
enabled.  Then, cpuidle_idle_call() will not need to re-enable
interrupts after calling cpuidle_enter_freeze() any more, because
the latter will return with interrupts enabled, in analogy with
cpuidle_enter().

Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
2015-02-28 23:46:24 +01:00
Jon DeVree
39afb5ee46 kernel/sys.c: fix UNAME26 for 4.0
There's a uname workaround for broken userspace which can't handle kernel
versions of 3.x.  Update it for 4.x.

Signed-off-by: Jon DeVree <nuxi@vault24.org>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-02-28 09:57:51 -08:00
Linus Torvalds
9ec0de0ee0 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching
Pull livepatching fixes from Jiri Kosina:
 "Two tiny fixes for livepatching infrastructure:

   - extending RCU critical section to cover all accessess to
     RCU-protected variable, by Petr Mladek

   - proper format string passing to kobject_init_and_add(), by Jiri
     Kosina"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
  livepatch: RCU protect struct klp_func all the time when used in klp_ftrace_handler()
  livepatch: fix format string in kobject_init_and_add()
2015-02-24 09:05:41 -08:00
Petr Mladek
c4ce0da8ec livepatch: RCU protect struct klp_func all the time when used in klp_ftrace_handler()
func->new_func has been accessed after rcu_read_unlock() in klp_ftrace_handler()
and therefore the access was not protected.

Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-02-22 23:02:56 +01:00
Linus Torvalds
a135c717d5 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS:

   - a number of fixes that didn't make the 3.19 release.

   - a number of cleanups.

   - preliminary support for Cavium's Octeon 3 SOCs which feature up to
     48 MIPS64 R3 cores with FPU and hardware virtualization.

   - support for MIPS R6 processors.

     Revision 6 of the MIPS architecture is a major revision of the MIPS
     architecture which does away with many of original sins of the
     architecture such as branch delay slots.  This and other changes in
     R6 require major changes throughout the entire MIPS core
     architecture code and make up for the lion share of this pull
     request.

   - finally some preparatory work for eXtendend Physical Address
     support, which allows support of up to 40 bit of physical address
     space on 32 bit processors"

     [ Ahh, MIPS can't leave the PAE brain damage alone.  It's like
       every CPU architect has to make that mistake, but pee in the snow
       by changing the TLA.  But whether it's called PAE, LPAE or XPA,
       it's horrid crud   - Linus ]

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
  MIPS: sead3: Corrected get_c0_perfcount_int
  MIPS: mm: Remove dead macro definitions
  MIPS: OCTEON: irq: add CIB and other fixes
  MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
  MIPS: OCTEON: More OCTEONIII support
  MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
  MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
  MIPS: OCTEON: Update octeon-model.h code for new SoCs.
  MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
  MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
  MIPS: OCTEON: Implement the core-16057 workaround
  MIPS: OCTEON: Delete unused COP2 saving code
  MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
  MIPS: OCTEON: Save and restore CP2 SHA3 state
  MIPS: OCTEON: Fix FP context save.
  MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
  MIPS: boot: Provide more uImage options
  MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
  MIPS: ip22-gio: Remove legacy suspend/resume support
  mips: pci: Add ifdef around pci_proc_domain
  ...
2015-02-21 19:41:38 -08:00
Linus Torvalds
f3c233d75e Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull ntp fix from Ingo Molnar:
 "An adjtimex interface regression fix for 32-bit systems"

[ A check that was added in a previous commit is really only a concern
  for 64bit systems, but was applied to both 32 and 64bit systems, which
  results in breaking 32bit systems.

  Thus the fix here is to make the check only apply to 64bit systems ]

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ntp: Fixup adjtimex freq validation on 32-bit systems
2015-02-21 11:05:22 -08:00
Linus Torvalds
10436cf881 Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
 "Two fixes: the paravirt spin_unlock() corruption/crash fix, and an
  rtmutex NULL dereference crash fix"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/spinlocks/paravirt: Fix memory corruption on unlock
  locking/rtmutex: Avoid a NULL pointer dereference on deadlock
2015-02-21 10:45:03 -08:00
Linus Torvalds
e2defd0271 Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
 "Thiscontains misc fixes: preempt_schedule_common() and io_schedule()
  recursion fixes, sched/dl fixes, a completion_done() revert, two
  sched/rt fixes and a comment update patch"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/rt: Avoid obvious configuration fail
  sched/autogroup: Fix failure to set cpu.rt_runtime_us
  sched/dl: Do update_rq_clock() in yield_task_dl()
  sched: Prevent recursion in io_schedule()
  sched/completion: Serialize completion_done() with complete()
  sched: Fix preempt_schedule_common() triggering tracing recursion
  sched/dl: Prevent enqueue of a sleeping task in dl_task_timer()
  sched: Make dl_task_time() use task_rq_lock()
  sched: Clarify ordering between task_rq_lock() and move_queued_task()
2015-02-21 10:40:02 -08:00
Linus Torvalds
3f4d9925e9 Merge branches 'core-urgent-for-linus' and 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rcu fix and x86 irq fix from Ingo Molnar:

 - Fix a bug that caused an RCU warning splat.

 - Two x86 irq related fixes: a hotplug crash fix and an ACPI IRQ
   registry fix.

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rcu: Clear need_qs flag to prevent splat

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/irq: Check for valid irq descriptor in check_irq_vectors_for_cpu_disable()
  x86/irq: Fix regression caused by commit b568b8601f
2015-02-21 10:36:06 -08:00
Linus Torvalds
4fbd0a81a0 KGDB/KDB New:
* KDB: improved searching
    * No longer enter debug core on panic if panic timeout is set
 
 KGDB/KDB regressions / cleanups
    * fix pdf doc build errors
    * prevent junk characters on kdb console from printk levels
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJU5qxHAAoJEIciOldedpOjliYP/izuoNZ/EtjjeihOL44ic0o0
 cmvdSc/ovR/mO4fbDpftMB0nhzclgRyAvr+VTPd3Bp5Poh+wJ0ZKu1R7f+ioSN73
 Y4ek9PJqPSBQr+JdfPK80N56Choeni48bsC6up12i3BTfXobj81zlu4Sj0SMOoHq
 IkFkB7soRuiFoc5IkKMvf3N3T9j1PnEULmHteNDRr0hTmGipEzkD3zocc/bRFV/l
 JTZRzIMGBNGnF01DPLDcuvbu0wGBh6ADMBLtx5v1UrhV32ypfJq2bgxFvgM/AXn2
 3VG4HcRbVsGmlBOahFR6X0DE/WAplw01yu1EabR2EWUePyz41cnSkxl4nR/NNhwz
 qMbr3uzu1iWUTTz5ySRcWxSuRRCihVQqNk6p+y21N/jY/5cr2jI03qJm0zZ/ObqL
 VUcPE7CfdcriCDXoepgXZE4XfX65Jf5tUiyiCj+1ds05ab5qHELIwKOZdjU2ON1b
 pb2ElPngGSEEoU/eSDgP2RVJ9Mk/k5s2TxaPXVJNkeWGNxPU5HtCytZpVI5hckbP
 /NZWTtyUDZ85is8cWUkHEdjnQ+CdzaA/FwJEqnB0or2is91mo8uBxP5BvdqPnPL0
 QdPPnVgD72dumXfJpH2HY3DdUs24LaP0vgSO8ELKgfA67nprS+5xztNSd8ekNnhF
 4wMhZbuAhB68E6bA0X7G
 =TH0R
 -----END PGP SIGNATURE-----

Merge tag 'for_linux-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb

Pull kgdb/kdb updates from Jason Wessel:
 "KGDB/KDB New:
   - KDB: improved searching
   - No longer enter debug core on panic if panic timeout is set

  KGDB/KDB regressions / cleanups
   - fix pdf doc build errors
   - prevent junk characters on kdb console from printk levels"

* tag 'for_linux-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
  kgdb, docs: Fix <para> pdfdocs build errors
  debug: prevent entering debug mode on panic/exception.
  kdb: Const qualifier for kdb_getstr's prompt argument
  kdb: Provide forward search at more prompt
  kdb: Fix a prompt management bug when using | grep
  kdb: Remove stack dump when entering kgdb due to NMI
  kdb: Avoid printing KERN_ levels to consoles
  kdb: Fix off by one error in kdb_cpu()
  kdb: fix incorrect counts in KDB summary command output
2015-02-20 15:13:29 -08:00
Colin Cross
5516fd7b92 debug: prevent entering debug mode on panic/exception.
On non-developer devices, kgdb prevents the device from rebooting
after a panic.

Incase of panics and exceptions, to allow the device to reboot, prevent
entering debug mode to avoid getting stuck waiting for the user to
interact with debugger.

To avoid entering the debugger on panic/exception without any extra
configuration, panic_timeout is being used which can be set via
/proc/sys/kernel/panic at run time and CONFIG_PANIC_TIMEOUT sets the
default value.

Setting panic_timeout indicates that the user requested machine to
perform unattended reboot after panic. We dont want to get stuck waiting
for the user input incase of panic.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: linux-kernel@vger.kernel.org
Cc: Android Kernel Team <kernel-team@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Colin Cross <ccross@android.com>
[Kiran: Added context to commit message.
panic_timeout is used instead of break_on_panic and
break_on_exception to honor CONFIG_PANIC_TIMEOUT
Modified the commit as per community feedback]
Signed-off-by: Kiran Raparthy <kiran.kumar@linaro.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
2015-02-19 12:39:03 -06:00
Daniel Thompson
32d375f6f2 kdb: Const qualifier for kdb_getstr's prompt argument
All current callers of kdb_getstr() can pass constant pointers via the
prompt argument. This patch adds a const qualification to make explicit
the fact that this is safe.

Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
2015-02-19 12:39:03 -06:00
Daniel Thompson
fb6daa7520 kdb: Provide forward search at more prompt
Currently kdb allows the output of comamnds to be filtered using the
| grep feature. This is useful but does not permit the output emitted
shortly after a string match to be examined without wading through the
entire unfiltered output of the command. Such a feature is particularly
useful to navigate function traces because these traces often have a
useful trigger string *before* the point of interest.

This patch reuses the existing filtering logic to introduce a simple
forward search to kdb that can be triggered from the more prompt.

Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
2015-02-19 12:39:03 -06:00