We need to ensure that we feed valid memory into the display plane
attached to the pipe when switching the pipe on. Otherwise, the display
engine may read through an invalid PTE and so throw an PGTBL_ER
exception.
As we need to perform load detection before even the first object is
allocated for the fbdev, there is no pre-existing object large enough
for us to borrow to use as the framebuffer. So we need to create one
and cleanup afterwards. At other times, the current fbcon may be large
enough for us to borrow it for duration of load detection.
Found by assert_fb_bound_for_plane().
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
As we now never attempt to steal a crtc for load detection, we either
set a mode on a new pipe, or change the dpms mode on an existing pipe.
Never both, so we can simplify the code slightly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
As we only allow the use of a disabled CRTC, we don't need to handle the
case where we are reusing an already enabled pipe.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
... and the no longer relevant comment. The code ceased stealing a pipe
for load detection a long time ago.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Keep all the state required for undoing and restoring the previous pipe
configuration together in a single struct passed from
intel_get_load_detect_pipe() to intel_release_load_detect_pipe() rather
than stuffing them inside the common encoder structure.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Check the return value from drm_crtc_set_mode(), report the failure
via a debug message and propagate the error back to the caller. This
prevents us from blissfully continuing to do the load detection on a
disabled pipe. Fortunately actual failure for modesetting is very rare,
and reported failures even rarer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
... and so remove the confusion as to whether to use the returned crtc
or intel_encoder->base.crtc with the subsequent load-detection. Even
though they were the same, the two instances of load-detection code
disagreed over which was the more correct.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Required so that we don't obliterate the queue if initialising the
rings after the global IRQ handler is installed.
[Jesse, you recently looked at refactoring the IRQ installation
routines, does moving the initialisation of ring buffer data structures away
from that routine make sense in your grand scheme?]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
If we're using vga switcheroo, the device may be turned off
and poking it can return random state. This provokes an OOPS fixed
separately by 8ff887c847 (drm/i915/dp: Be paranoid in case we disable a
DP before it is attached). Trying to use and respond to events on a
device that has been turned off by the user is in principle a silly thing
to do.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Despite the fixes in 548f245ba6 (drm/i915: fix per-pipe reads after
"cleanup"), we missed one neighbouring read that was mistakenly replaced
with the reg value in 9db4a9c (drm/i915: cleanup per-pipe reg usage).
This was preventing us from correctly determining the mode the BIOS left
the panel in for machines that neither have an OpRegion nor access to
the VBT, (e.g. the EeePC 700).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
When enabling the plane, it is helpful to have already pointed that
plane to valid memory or else we may incur the wrath of a PGTBL_ER.
This code preserved the behaviour from the bad old days for unknown
reasons...
Found by assert_fb_bound_for_plane().
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Given that the hardware may be left in a random condition by the BIOS,
it is conceivable that we then attempt to clear the DP_PIPEB_SELECT bit
without us ever enabling/attaching the DP encoder to a pipe. Thus
causing a NULL deference when we attempt to wait for a vblank on that
crtc.
Reported-and-tested-by: Bryan Christ <bryan.christ@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36314
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36456
Reported-and-tested-by: Bo Wang <bo.b.wang@intel.com>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
i915 calls the panic handler function on last close to reset the modes,
however this is a really bad idea for multi-gpu machines, esp shareable
gpus machines. So add a new entry point for the driver to just restore
its own fbcon mode.
v2: move code into fb helper, fix panic code to block mode change on
powered off GPUs.
[airlied: this hits drm core and I wrote it and it was reviewed on intel-gfx
so really I signed it off twice ;-).]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: Initialise g4x watermarks for disabled pipes
drm/i915: Sanitize the output registers after resume
drm/i915/tv: Fix modeset flickering introduced in 7f58aabc3
drm/i915/tv: Only poll for TV connections
drm/i915/tv: Remember the detected TV type
We were using uninitialised watermarks values for disabled pipes which
were combined into a single WM register and so corrupting the values for
the enabled pipe and upsetting the display hardware.
Reported-by: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32612
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Similar to booting, we need to inspect the state left by the BIOS and
remove any conflicting bits before we take over. The example reported by
Seth Forshee is very similar to the bug we encountered with the state left
by grub2, that the crtc pipe<->planning mapping was reversed from our
expectations and so we failed to turn off the outputs when booting or,
in this case, resuming. This may be in fact the same bug, but triggered
at resume time.
This patch rearranges the code we already have to clear up the
conflicting state upon init and calls it from reset (which is called
after we have lost control of the hardware, i.e. along both the boot and
resume paths) instead.
Reported-and-tested-by: Seth Forshee <seth.forshee@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35796
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The tidy ups in 7f58aabc36 ("drm/i915:
cleanup per-pipe reg usage") changed intel_crtc->plane to intel_crtc->pipe in
intel_tv_mode_set(). This caused the screen to quickly turn off before
returning whenever modesetting/mode probing took place on my 915GM EeePC
900 creating a flickering effect. This patch changes intel_crtc->pipe back
to intel_crtc->plane which solves the problem for me.
References: https://bugs.freedesktop.org/show_bug.cgi?id=35903
Signed-off-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Humbly-acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
As a probe for a TV connection modifies the TV_CTL register, it causes a
loss of sync and a regular glitch on the output. This is highly
undesirable when using the TV, so only poll for TV connections and wait
for an explicit query for detecting the disconnection event.
Reported-by: Mathew McKernan <matmckernan@rauland.com.au>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35977
Signed-off-by: Mathew McKernan <matmckernan@rauland.com.au>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
During detect() we would probe the connection bits to determine if
there was a TV attached, and what video input type (Component, S-Video,
Composite, etc) to use. However, we promptly discarded this vital bit of
information and never propagated it to where it was used to determine
the correct modes and setup the control registers. Fix it!
This fixes a regression from 7b334fcb45.
Reported-and-tested-by: Mathew McKernan <matmckernan@rauland.com.au>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35977
Signed-off-by: Mathew McKernan <matmckernan@rauland.com.au>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
This is a revert of 428d2e828c.
This is broken in the same manner as for VGA: trying to write to an
invalid address on the (currently 7-bit) i2c bus.
One notable failure appears to be for MacBooks. The scary part was that
it gave the appearance of working (i.e. reporting the absence of the
panel) on various all-in-one machines with ghost LVDS panels and not
failing for laptops.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Keith Packard <keithp@keithp.com>
This is a moral revert of 6ec3d0c0e9.
Following the fix to reset the GMBUS controller after a NAK, we finally
utilize the 0xa0 probe for a CRT connection. And discover that the code
is broken. Shock.
There are a number of issues, but following a key insight from Dave
Airlie, that 0xA0 is an invalid address on a 7-bit bus (though not if we
were to enable 10-bit addressing), and would look like the EDID port
0x50, it is possible to see where the confusion starts.
In short, a write to 0xA0 is accepted by the GMBUS controller which we
interpreted as meaning the existence of a connection (a slave on the
other end of the wire ACKing the write). That was false.
During testing with a broken GMBUS implementation, which never reset an
earlier NAK, this test always reported a NAK and so we proceeded on to
the next test.
Reported-and-tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35904
Reported-and-tested-by: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32612
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Keith Packard <keithp@keithp.com>
Once a NAK has been asserted by the slave, we need to reset the GMBUS
controller in order to continue. This is done by asserting the Software
Clear Interrupt bit and then clearing it again to restore operations.
If we don't clear the NAK, then all future GMBUS xfers will fail,
including DDC probes and EDID retrieval.
v2: Add some comments as suggested by Keith Packard.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35781
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: "Mengmeng Meng" <mengmeng.meng@intel.com>
During modesetting, we need to wait for the hardware to report
readiness by polling the registers. Normally, we call msleep() between
reads, because some state changes may take a whole vblank or more
to complete. However during a panic, we are in an atomic context and
cannot sleep. Instead, busy spin polling the termination condition.
References: https://bugzilla.kernel.org/show_bug.cgi?id=31772
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The LVDS connector should default to connected. We tried our best to
verify the claims of the BIOS that the hardware exists during init(),
and then during detect() we then try to verify that the panel is open.
In the event of an unsuccessful query, we should then always report
that the LVDS panel is connected. This was only the case for gen2/3,
later generations leaked the return value from the panel probe instead.
Reported-and-tested-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
This reverts commit a7a75c8f70.
There are two different variations on how Intel hardware addresses the
"Hardware Status Page". One as a location in physical memory and the
other as an offset into the virtual memory of the GPU, used in more
recent chipsets. (The HWS itself is a cacheable region of memory which
the GPU can write to without requiring CPU synchronisation, used for
updating various details of hardware state, such as the position of
the GPU head in the ringbuffer, the last breadcrumb seqno, etc).
These two types of addresses were updated in different locations of code
- one inline with the ringbuffer initialisation, and the other during
device initialisation. (The HWS page is logically associated with
the rings, and there is one HWS page per ring.) During resume, only the
ringbuffers were being re-initialised along with the virtual HWS page,
leaving the older physical address HWS untouched. This then caused a
hang on the older gen3/4 (915GM, 945GM, 965GM) the first time we tried
to synchronise the GPU as the breadcrumbs were never being updated.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Jan Niehusmann <jan@gondor.com>
Reported-and-tested-by: Justin P. Mattock <justinmattock@gmail.com>
Reported-and-tested-by: Michael "brot" Groh <brot@minad.de>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
We always skipped flushing the BLT ring if the request flush did not
include the RENDER domain. However, this neglects that we try to flush
the COMMAND domain after every batch and before the breadcrumb interrupt
(to make sure the batch is indeed completed prior to the interrupt
firing and so insuring CPU coherency). As a result of the missing flush,
incoherency did indeed creep in, most notable when using lots of command
buffers and so potentially rewritting an active command buffer (i.e.
the GPU was still executing from it even though the following interrupt
had already fired and the request/buffer retired).
As all ring->flush routines now have the same preconditions, de-duplicate
and move those checks up into i915_gem_flush_ring().
Fixes gem_linear_blit.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35284
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: mengmeng.meng@intel.com
Along the fast path for relocation handling, we attempt to copy directly
from the user data structures whilst holding our mutex. This causes
lockdep to warn about circular lock dependencies if we need to pagefault
the user pages. [Since when handling a page fault on a mmapped bo, we
need to acquire the struct mutex whilst already holding the mm
semaphore, it is then verboten to acquire the mm semaphore when already
holding the struct mutex. The likelihood of the user passing in the
relocations contained in a GTT mmaped bo is low, but conceivable for
extreme pathology.] In order to force the mm to return EFAULT rather
than handle the pagefault, we therefore need to disable pagefaults
across the relocation fast path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix up the debug file to report the right frequencies. On SNB, we program
the PCU with a frequency ratio, which is multiplied by 100MHz on the CPU
side. But GFX only runs at half that, so report it as such to avoid
confusion.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
The order of the calls does matter indeed. Swapping the call order of
intel_dp_destroy() and intel_dp_encoder_destroy() fixes the problem.
This is because i2c_del_adapter unregisters the device which parent is
intel_connector, and connectors are removed in intel_dp_destroy(). Thus
intel_dp_encoder_destroy() must be called before intel_dp_destroy().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24822
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
... even though it was disabled. A mistake in the handling of fence reuse
caused us to skip the vital delay of waiting for the object to finish
rendering before changing the register. This resulted in us changing the
fence register whilst the bo was active and so causing the blits to
complete using the wrong stride or even the wrong tiling. (Visually the
effect is that small blocks of the screen look like they have been
interlaced). The fix is to wait for the GPU to finish using the memory
region pointed to by the fence before changing it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34584
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Note for 2.6.38-stable, we need to reintroduce the interruptible passing]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Dave Airlie <airlied@linux.ie>
A broken implementation of is_pot() prevented the detection of when a
singular pipe was enabled. Eric Anholt pointed out the existence of
is_power_of_2() so use that instead of our broken code!
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35402
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Tested-by: xunx.fang@intel.com
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When i915_gem_retire_requests_ring calls i915_gem_request_remove_from_client,
the client_list for that request may already be removed in i915_gem_release.
So we may call twice list_del(&request->client_list), resulting in an
oops like this report:
[126167.230394] BUG: unable to handle kernel paging request at 00100104
[126167.230699] IP: [<f8c2ce44>] i915_gem_retire_requests_ring+0xd4/0x240 [i915]
[126167.231042] *pdpt = 00000000314c1001 *pde = 0000000000000000
[126167.231314] Oops: 0002 [#1] SMP
[126167.231471] last sysfs file: /sys/devices/LNXSYSTM:00/device:00/PNP0C0A:00/power_supply/BAT1/current_now
[126167.231901] Modules linked in: snd_seq_dummy nls_utf8 isofs btrfs zlib_deflate libcrc32c ufs qnx4 hfsplus hfs minix ntfs vfat msdos fat jfs xfs exportfs reiserfs cryptd aes_i586 aes_generic binfmt_misc vboxnetadp vboxnetflt vboxdrv parport_pc ppdev snd_hda_codec_hdmi snd_hda_codec_conexant snd_hda_intel snd_hda_codec snd_hwdep arc4 snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq uvcvideo videodev snd_timer snd_seq_device joydev iwlagn iwlcore mac80211 snd cfg80211 soundcore i915 drm_kms_helper snd_page_alloc psmouse drm serio_raw i2c_algo_bit video lp parport usbhid hid sky2 sdhci_pci ahci sdhci libahci
[126167.232018]
[126167.232018] Pid: 1101, comm: Xorg Not tainted 2.6.38-6-generic-pae #34-Ubuntu Gateway MC7833U /
[126167.232018] EIP: 0060:[<f8c2ce44>] EFLAGS: 00213246 CPU: 0
[126167.232018] EIP is at i915_gem_retire_requests_ring+0xd4/0x240 [i915]
[126167.232018] EAX: 00200200 EBX: f1ac25b0 ECX: 00000040 EDX: 00100100
[126167.232018] ESI: f1a2801c EDI: e87fc060 EBP: ef4d7dd8 ESP: ef4d7db0
[126167.232018] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[126167.232018] Process Xorg (pid: 1101, ti=ef4d6000 task=f1ba6500 task.ti=ef4d6000)
[126167.232018] Stack:
[126167.232018] f1a28000 f1a2809c f1a28094 0058bd97 f1aa2400 f1a2801c 0058bd7b 0058bd85
[126167.232018] f1a2801c f1a28000 ef4d7e38 f8c2e995 ef4d7e30 ef4d7e60 c14d1ebc f6b3a040
[126167.232018] f1522cc0 000000db 00000000 f1ba6500 ffffffa1 00000000 00000001 f1a29214
[126167.232018] Call Trace:
Unfortunately the call trace reported was cut, but looking at debug
symbols the crash is at __list_del, when probably list_del is called
twice on the same request->client_list, as the dereferenced value is
LIST_POISON1 + 4, and by looking more at the debug symbols before
list_del call it should have being called by
i915_gem_request_remove_from_client
And as I can see in the code, it seems we indeed have the possibility
to remove a request->client_list twice, which would cause the above,
because we do list_del(&request->client_list) on both
i915_gem_request_remove_from_client and i915_gem_release
As Chris Wilson pointed out, it's indeed the case:
"(...) I had thought that the actual insertion/deletion was serialised
under the struct mutex and the intention of the spinlock was to protect
the unlocked list traversal during throttling. However, I missed that
i915_gem_release() is also called without struct mutex and so we do need
the double check for i915_gem_request_remove_from_client()."
This change does the required check to avoid the duplicate remove of
request->client_list.
Bugzilla: http://bugs.launchpad.net/bugs/733780
Cc: stable@kernel.org # 2.6.38
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the pipe or plane is already enabled, then we do not need to enable
it again and can skip the delay. Similarly if it is already disabled
when we want to disable it, we can also skip it.
This fixes a regression from b24e717988, which caused the LVDS
output on one PineView machine to become corrupt after changing
orientation several times.
References: https://bugs.freedesktop.org/show_bug.cgi?id=34601
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Tested-by: mengmeng.meng@intel.com
... as wait_for_vblank (and friends) will do a flush of the MMIO writes
anyway.
References: https://bugs.freedesktop.org/show_bug.cgi?id=34601
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This commit changed an internal radeon structure, that meant a new driver
in -next had to be fixed up, merge in the commit and fix up the driver.
Also fixes a trivial nouveau merge.
Conflicts:
drivers/gpu/drm/nouveau/nouveau_mem.c
At least on my HP 2540p this is wrong at bootup, fine
at any other time once a lid event has occured. This is due to
_REG vs _INI ordering in the ACPI tables.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of ../drm-next: (755 commits)
drm/i915: Only wait on a pending flip if we intend to write to the buffer
drm/i915/dp: Sanity check eDP existence
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
drm/i915: Don't save/restore hardware status page address register
drm/i915: don't store the reg value for HWS_PGA
drm/i915: fix memory corruption with GM965 and >4GB RAM
Linux 2.6.38-rc7
Revert "TPM: Long default timeout fix"
drm/i915: Re-enable GPU semaphores for SandyBridge mobile
drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
drm/i915: Allow relocation deltas outside of target bo
drm/i915: Silence an innocuous compiler warning for an unused variable
fs/block_dev.c: fix new kernel-doc warning
ACPI: Fix build for CONFIG_NET unset
mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
x86: Use u32 instead of long to set reset vector back to 0
...
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
This reverts commit 951f3512db
drm/i915: Do not handle backlight combination mode specially
since this commit introduced other regressions due to untouched LBPC
register, e.g. the backlight dimmed after resume.
In addition to the revert, this patch includes a fix for the original
issue (weird backlight levels) by removing the wrong bit shift for
computing the current backlight level.
Also, including typo fixes (lpbc -> lbpc).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34524
Acked-by: Indan Zupancic <indan@nul.nu>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some hardware claims to have both an LVDS panel and an eDP output.
Whilst this may be true in a rare case, more often it is just broken
hardware. If we see an eDP device we know that it must be connected and
so we can confirm its existence with a simple probe.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34165
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24822
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Early gen3 and gen2 chipset do not have the relaxed per-surface tiling
constraints of the later chipsets, so we need to check that the GTT
alignment is correct for the new tiling. If it is not, we need to
rebind.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Andi Kleen narrowed his GPU hangs on his Sugar Bay (SNB desktop) rev 09
down to the use of GPU semaphores, and we already know that they appear
broken up to Huron River (mobile) rev 08. (I'm optimistic that disabling
GPU semaphores is simply hiding another bug by the latency and
side-effects of the additional device interaction it introduces...)
However, use of semaphores is a massive performance improvement... Only
as long as the system remains stable. Enable at your peril.
Reported-by: Andi Kleen <andi-fd@firstfloor.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33921
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
