In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
EMC1412, EMC1413, and EMC1414 are fully compatible to EMC1402, EMC1403,
and EMC1404, and even report the same chip ID. Add to device ID table
to enable instantiation with correct chip names.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writing the hysteresis limit returned -ERANGE if the written hysteresis
was too high or too low. Relax error check and adjust the hysteresis
value to its valid range.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips in this chip series only support a single hysteresis value. Having
multiple writable hysteresis attributes is therefore confusing, since a single
write affects all hysteresis temperatures. Make all but one (temp1_crit_hyst)
read-only.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Alarm and fault status register on EMC1402, EMC1412, and EMC1422 is reported
in a different register than with other chips. Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for emc1402/emc1412/emc1422 temperature monitoring chips.
This line of sensors only has 2 temperature channels (internal and external)
in comparison to the emc14x3 (3 channels) and emc14x4 (4 channels).
Signed-off-by: Josef Gajdusek <atx@atx.name>
[Guenter Roeck: ordered i2c address list, updated description/headline]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The datasheet for EMC1413/EMC1414, which is fully compatible to
EMC1403/1404 and uses the same chip identification, references revision
numbers 0x01, 0x03, and 0x04. Accept the full range of revision numbers
from 0x01 to 0x04 to make sure none are missed.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Cc: stable@vger.kernel.org
[Guenter Roeck: Updated headline and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 454aee17f claims to convert driver emc1403 to use
devm_hwmon_device_register_with_groups, however the patch itself makes
use of hwmon_device_register_with_groups instead. As the driver remove
function was still dropped, the hwmon device is no longer unregistered
on driver removal, leading to a resource leak.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 454aee17f hwmon: (emc1403) Convert to use devm_hwmon_device_register_with_groups
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org [3.13+]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Attempts to set the hysteresis value to a temperature below the target
limit fails with "write error: Numerical result out of range" due to
an inverted comparison.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org
[Guenter Roeck: Updated headline and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
EMC1404 and EMC1424 are similar to EMC1403 and EMC1423,
but support an additional external temperature sensor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many hwmon drivers use jiffies but omit the inclusion of the header
file. Fix that, and also fix one driver which was including the header
file but didn't need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Rudolf Marek <r.marek@assembler.cz>
This patch converts the drivers in drivers/hwmon/* to use the
module_i2c_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Guillaume Ligneul <guillaume.ligneul@gmail.com>
Cc: David George <david.george@ska.ac.za>
Cc: "Hans J. Koch" <hjk@hansjkoch.de>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
replaced strict_strtol with kstrtol and
replaced strict_strtuol with kstrtuol
This satisfies checkpatch -f
Compile tested only: no warnings or errors given
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
I2C address range included 0x2a, which the chips do not support.
Replace with 0x29 which is supported but was missing.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
EMC1423 uses the similar register and adds a hardware shutdown pin to
protect exceed temperature. This function is set by resistor; it's not
necessary to do anything in the driver except add the emc1423 pid of 0x23.
Signed-off-by: Jekyll Lai <jekyll_lai@wistron.com>
[Updated Kconfig/comments and minor further changes asked for by the hwmon
maintainers]
Signed-off-by: Alan Cox <alan@linux.intel.com>
[Fixed checkpatch warning]
Signed-of--by: Jean Delvare <khali@linux-fr.org>
It is unnecessary and wrong to call hwmon_device_unregister in error
handling before hwmon_device_register is called.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add back the power interface we lost due to a slight misunderstanding of
the maintainers wishes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Provides support for the EMC1403 thermal sensor. Only reporting of values
is supported. The various Moorestown specific extras to do with thermal
alerts and the like are not in this version of the driver.
Considerably edited and tidied up by Alan Cox, plus fixes and detection
bits from Jean Delvare.
Signed-off-by: Kalhan Trisal <kalhan.trisal@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
