The old code would += the total errors every time
stats were gathered. Instead, keep a count of short-pkt
and long-pkt counters and then simply add them together
for the rx-over-length stat.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the NIC to receive packets with bad FCS
and other errors. Good for sniffing packets on flakey
networks.
v4: Only flax rx-over-length errors if pkt is beyond
maximum expected packet size, not just beyond the MTU.
This matches the existing logic for this counter.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This can aid with testing the RX logic for bad
CRCs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows e100 to be configured to append the
Ethernet FCS to the skb.
Useful for sniffing networks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform another round of floor sweeping, converting the .get_drvinfo
routines of additional drivers from strcpy to strlcpy along with
some conversion of sprintf to snprintf.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e100 parts don't support vlan offload but they generally do
allow use of vlans in higher software layers via the 8021q module.
That said, there are a couple of really old revisions of e100
hardware that don't even allow the longer frame sizes
required for vlan use with standard MTU.
Use the VLAN_CHALLENGED flag to prevent vlan binding to these
devices.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: David Lamparter <equinox@diac24.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and
the necessary Kconfig and Makefile changes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
