As it turns out, the "stdbuf" command will actually force all
subprocesses into unbuffered output, and some implementations of "echo"
turn into single-character writes, which utterly wrecks writes to /sys
and /proc files.
Instead, drop the "stdbuf" usage, and for any tests that want explicit
flushing between newlines, they'll have to add "fflush(stdout);" as
needed.
Reported-by: Takashi Iwai <tiwai@suse.de>
Fixes: 5c069b6ded ("selftests: Move test output to diagnostic lines")
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Since sub-testing can now be detected by indentation level, this removes
KSFT_TAP_LEVEL so that subtests report their TAP header for later parsing.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This changes the selftest output so that each test's output is prefixed
with "# " as a TAP "diagnostic line".
This creates a bit of a kernel-specific TAP dialect where the diagnostics
precede the results. The TAP spec isn't entirely clear about this, though,
so I think it's the correct solution so as to keep interactive runs making
sense. If the output _followed_ the result line in the spec-suggested
YAML form, each test would dump all of its output at once instead of as
it went, making debugging harder.
This does, however, solve the recursive TAP output problem, as sub-tests
will simply be prefixed by "# ". Parsing sub-tests becomes a simple
problem of just removing the first two characters of a given top-level
test's diagnostic output, and parsing the results.
Note that the shell construct needed to both get an exit code from
the first command in a pipe and still filter the pipe (to add the "# "
prefix) uses a POSIX solution rather than the bash "pipefail" option
which is not supported by dash.
Since some test environments may have a very minimal set of utilities
available, the new prefixing code will fall back to doing line-at-a-time
prefixing if perl and/or stdbuf are not available.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
If a test was missing (e.g. wrong architecture, etc), the test runner
would incorrectly claim the test was non-executable. This adds an
existence check to report correctly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The TAP version 13 spec requires a "plan" line, which has been missing.
Since we always know how many tests we're going to run, emit the count on
the plan line. This also fixes the result lines to remove the "1.." prefix
which is against spec, and to mark skips with the correct "# SKIP" suffix.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This moves the logic for running multiple tests into a single "run_many"
function of runner.sh. Both "run_tests" and "emit_tests" are modified to
use it. Summary handling is now controlled by the "per_test_logging"
shell flag.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
In order to improve the reusability of the kselftest test running logic,
this extracts the single-test logic from lib.mk into kselftest/runner.sh
which lib.mk can call directly. No changes in output.
As part of the change, this moves the "summary" Makefile logic around
to set a new "logfile" output. This will be used again in the future
"emit_tests" target as well.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
