An MSI interrupt should only be delivered to the lowest priority CPU
when it has RH=1, regardless of the delivery mode. Modified
kvm_is_dm_lowest_prio() to check for either irq->delivery_mode == APIC_DM_LOWPRI
or irq->msi_redir_hint.
Moved kvm_is_dm_lowest_prio() into lapic.h and renamed to
kvm_lowest_prio_delivery().
Changed a check in kvm_irq_delivery_to_apic_fast() from
irq->delivery_mode == APIC_DM_LOWPRI to kvm_is_dm_lowest_prio().
Signed-off-by: James Sullivan <sullivan.james.f@gmail.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extended struct kvm_lapic_irq with bool msi_redir_hint, which will
be used to determine if the delivery of the MSI should target only
the lowest priority CPU in the logical group specified for delivery.
(In physical dest mode, the RH bit is not relevant). Initialized the value
of msi_redir_hint to true when RH=1 in kvm_set_msi_irq(), and initialized
to false in all other cases.
Added value of msi_redir_hint to a debug message dump of an IRQ in
apic_send_ipi().
Signed-off-by: James Sullivan <sullivan.james.f@gmail.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change to u16 if they only contain data in the low 16 bits.
Change the level field to bool, since we assign 1 sometimes, but
just mask icr_low with APIC_INT_ASSERT in apic_send_ipi.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86 architecture defines differences between the reset and INIT sequences.
INIT does not initialize the FPU (including MMX, XMM, YMM, etc.), TSC, PMU,
MSRs (in general), MTRRs machine-check, APIC ID, APIC arbitration ID and BSP.
References (from Intel SDM):
"If the MP protocol has completed and a BSP is chosen, subsequent INITs (either
to a specific processor or system wide) do not cause the MP protocol to be
repeated." [8.4.2: MP Initialization Protocol Requirements and Restrictions]
[Table 9-1. IA-32 Processor States Following Power-up, Reset, or INIT]
"If the processor is reset by asserting the INIT# pin, the x87 FPU state is not
changed." [9.2: X87 FPU INITIALIZATION]
"The state of the local APIC following an INIT reset is the same as it is after
a power-up or hardware reset, except that the APIC ID and arbitration ID
registers are not affected." [10.4.7.3: Local APIC State After an INIT Reset
("Wait-for-SIPI" State)]
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1428924848-28212-1-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introducing KVM_CAP_DISABLE_QUIRKS for disabling x86 quirks that were previous
created in order to overcome QEMU issues. Those issue were mostly result of
invalid VM BIOS. Currently there are two quirks that can be disabled:
1. KVM_QUIRK_LINT0_REENABLED - LINT0 was enabled after boot
2. KVM_QUIRK_CD_NW_CLEARED - CD and NW are cleared after boot
These two issues are already resolved in recent releases of QEMU, and would
therefore be disabled by QEMU.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1428879221-29996-1-git-send-email-namit@cs.technion.ac.il>
[Report capability from KVM_CHECK_EXTENSION too. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use __kvm_guest_{enter|exit} instead of kvm_guest_{enter|exit}
where interrupts are disabled.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The kvmclock spec says that the host will increment a version field to
an odd number, then update stuff, then increment it to an even number.
The host is buggy and doesn't do this, and the result is observable
when one vcpu reads another vcpu's kvmclock data.
There's no good way for a guest kernel to keep its vdso from reading
a different vcpu's kvmclock data, but we don't need to care about
changing VCPUs as long as we read a consistent data from kvmclock.
(VCPU can change outside of this loop too, so it doesn't matter if we
return a value not fit for this VCPU.)
Based on a patch by Radim Krčmář.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
The host's decision to enable machine check exceptions should remain
in force during non-root mode. KVM was writing 0 to cr4 on VCPU reset
and passed a slightly-modified 0 to the vmcs.guest_cr4 value.
Tested: Built.
On earlier version, tested by injecting machine check
while a guest is spinning.
Before the change, if guest CR4.MCE==0, then the machine check is
escalated to Catastrophic Error (CATERR) and the machine dies.
If guest CR4.MCE==1, then the machine check causes VMEXIT and is
handled normally by host Linux. After the change, injecting a machine
check causes normal Linux machine check handling.
Signed-off-by: Ben Serebrin <serebrin@google.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Soft mmu uses direct shadow page to fill guest large mapping with small
pages if huge mapping is disallowed on host. So zapping direct shadow
page works well both for soft mmu and hard mmu, it's just less widely
applicable.
Fix the comment to reflect this.
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Message-Id: <552C91BA.1010703@linux.intel.com>
[Fix comment wording further. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As Andres pointed out:
| I don't understand the value of this check here. Are we looking for a
| broken memslot? Shouldn't this be a BUG_ON? Is this the place to care
| about these things? npages is capped to KVM_MEM_MAX_NR_PAGES, i.e.
| 2^31. A 64 bit overflow would be caused by a gigantic gfn_start which
| would be trouble in many other ways.
This patch drops the memslot overflow check to make the codes more simple.
Reviewed-by: Andres Lagar-Cavilla <andreslc@google.com>
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Message-Id: <1429064694-3072-1-git-send-email-wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sparse is reporting a "we previously assumed 'src' could be null" error.
This is true as far as the static analyzer can see, but in practice only
IPIs can set shorthand to self and they also set 'src', so it's ok.
Still, move the initialization of x2apic_ipi (and thus the NULL check for
src right before the first use.
While at it, initializing ret to "false" is somewhat confusing because of
the almost immediate assigned of "true" to the same variable. Thus,
initialize it to "true" and modify it in the only path that used to use
the value from "bool ret = false". There is no change in generated code
from this change.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_init_msr_list is currently called before hardware_setup. As a result,
vmx_mpx_supported always returns false when kvm_init_msr_list checks whether to
save MSR_IA32_BNDCFGS.
Move kvm_init_msr_list after vmx_hardware_setup is called to fix this issue.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1428864435-4732-1-git-send-email-namit@cs.technion.ac.il>
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull timer updates from Ingo Molnar:
"The main changes in this cycle were:
- clockevents state machine cleanups and enhancements (Viresh Kumar)
- clockevents broadcast notifier horror to state machine conversion
and related cleanups (Thomas Gleixner, Rafael J Wysocki)
- clocksource and timekeeping core updates (John Stultz)
- clocksource driver updates and fixes (Ben Dooks, Dmitry Osipenko,
Hans de Goede, Laurent Pinchart, Maxime Ripard, Xunlei Pang)
- y2038 fixes (Xunlei Pang, John Stultz)
- NMI-safe ktime_get_raw_fast() and general refactoring of the clock
code, in preparation to perf's per event clock ID support (Peter
Zijlstra)
- generic sched/clock fixes, optimizations and cleanups (Daniel
Thompson)
- clockevents cpu_down() race fix (Preeti U Murthy)"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
timers/PM: Drop unnecessary braces from tick_freeze()
timers/PM: Fix up tick_unfreeze()
timekeeping: Get rid of stale comment
clockevents: Cleanup dead cpu explicitely
clockevents: Make tick handover explicit
clockevents: Remove broadcast oneshot control leftovers
sched/idle: Use explicit broadcast oneshot control function
ARM: Tegra: Use explicit broadcast oneshot control function
ARM: OMAP: Use explicit broadcast oneshot control function
intel_idle: Use explicit broadcast oneshot control function
ACPI/idle: Use explicit broadcast control function
ACPI/PAD: Use explicit broadcast oneshot control function
x86/amd/idle, clockevents: Use explicit broadcast oneshot control functions
clockevents: Provide explicit broadcast oneshot control functions
clockevents: Remove the broadcast control leftovers
ARM: OMAP: Use explicit broadcast control function
intel_idle: Use explicit broadcast control function
cpuidle: Use explicit broadcast control function
ACPI/processor: Use explicit broadcast control function
ACPI/PAD: Use explicit broadcast control function
...
ARM/ARM64: fixes for live migration, irqfd and ioeventfd support (enabling
vhost, too), page aging
s390: interrupt handling rework, allowing to inject all local interrupts
via new ioctl and to get/set the full local irq state for migration
and introspection. New ioctls to access memory by virtual address,
and to get/set the guest storage keys. SIMD support.
MIPS: FPU and MIPS SIMD Architecture (MSA) support. Includes some patches
from Ralf Baechle's MIPS tree.
x86: bugfixes (notably for pvclock, the others are small) and cleanups.
Another small latency improvement for the TSC deadline timer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVJ9vmAAoJEL/70l94x66DoMEH/R3rh8IMf4jTiWRkcqohOMPX
k1+NaSY/lCKayaSgggJ2hcQenMbQoXEOdslvaA/H0oC+VfJGK+lmU6E63eMyyhjQ
Y+Px6L85NENIzDzaVu/TIWWuhil5PvIRr3VO8cvntExRoCjuekTUmNdOgCvN2ObW
wswN2qRdPIeEj2kkulbnye+9IV4G0Ne9bvsmUdOdfSSdi6ZcV43JcvrpOZT++mKj
RrKB+3gTMZYGJXMMLBwMkdl8mK1ozriD+q0mbomT04LUyGlPwYLl4pVRDBqyksD7
KsSSybaK2E4i5R80WEljgDMkNqrCgNfg6VZe4n9Y+CfAAOToNnkMJaFEi+yuqbs=
=yu2b
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"First batch of KVM changes for 4.1
The most interesting bit here is irqfd/ioeventfd support for ARM and
ARM64.
Summary:
ARM/ARM64:
fixes for live migration, irqfd and ioeventfd support (enabling
vhost, too), page aging
s390:
interrupt handling rework, allowing to inject all local interrupts
via new ioctl and to get/set the full local irq state for migration
and introspection. New ioctls to access memory by virtual address,
and to get/set the guest storage keys. SIMD support.
MIPS:
FPU and MIPS SIMD Architecture (MSA) support. Includes some
patches from Ralf Baechle's MIPS tree.
x86:
bugfixes (notably for pvclock, the others are small) and cleanups.
Another small latency improvement for the TSC deadline timer"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (146 commits)
KVM: use slowpath for cross page cached accesses
kvm: mmu: lazy collapse small sptes into large sptes
KVM: x86: Clear CR2 on VCPU reset
KVM: x86: DR0-DR3 are not clear on reset
KVM: x86: BSP in MSR_IA32_APICBASE is writable
KVM: x86: simplify kvm_apic_map
KVM: x86: avoid logical_map when it is invalid
KVM: x86: fix mixed APIC mode broadcast
KVM: x86: use MDA for interrupt matching
kvm/ppc/mpic: drop unused IRQ_testbit
KVM: nVMX: remove unnecessary double caching of MAXPHYADDR
KVM: nVMX: checks for address bits beyond MAXPHYADDR on VM-entry
KVM: x86: cache maxphyaddr CPUID leaf in struct kvm_vcpu
KVM: vmx: pass error code with internal error #2
x86: vdso: fix pvclock races with task migration
KVM: remove kvm_read_hva and kvm_read_hva_atomic
KVM: x86: optimize delivery of TSC deadline timer interrupt
KVM: x86: extract blocking logic from __vcpu_run
kvm: x86: fix x86 eflags fixed bit
KVM: s390: migrate vcpu interrupt state
...
Dirty logging tracks sptes in 4k granularity, meaning that large sptes
have to be split. If live migration is successful, the guest in the
source machine will be destroyed and large sptes will be created in the
destination. However, the guest continues to run in the source machine
(for example if live migration fails), small sptes will remain around
and cause bad performance.
This patch introduce lazy collapsing of small sptes into large sptes.
The rmap will be scanned in ioctl context when dirty logging is stopped,
dropping those sptes which can be collapsed into a single large-page spte.
Later page faults will create the large-page sptes.
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Message-Id: <1428046825-6905-1-git-send-email-wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CR2 is not cleared as it should after reset. See Intel SDM table named "IA-32
Processor States Following Power-up, Reset, or INIT".
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427933438-12782-5-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DR0-DR3 are not cleared as they should during reset and when they are set from
userspace. It appears to be caused by c77fb5fe6f ("KVM: x86: Allow the guest
to run with dirty debug registers").
Force their reload on these situations.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427933438-12782-4-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After reset, the CPU can change the BSP, which will be used upon INIT. Reset
should return the BSP which QEMU asked for, and therefore handled accordingly.
To quote: "If the MP protocol has completed and a BSP is chosen, subsequent
INITs (either to a specific processor or system wide) do not cause the MP
protocol to be repeated."
[Intel SDM 8.4.2: MP Initialization Protocol Requirements and Restrictions]
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427933438-12782-3-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
recalculate_apic_map() uses two passes over all VCPUs. This is a relic
from time when we selected a global mode in the first pass and set up
the optimized table in the second pass (to have a consistent mode).
Recent changes made mixed mode unoptimized and we can do it in one pass.
Format of logical MDA is a function of the mode, so we encode it in
apic_logical_id() and drop obsoleted variables from the struct.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1423766494-26150-5-git-send-email-rkrcmar@redhat.com>
[Add lid_bits temporary in apic_logical_id. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We want to support mixed modes and the easiest solution is to avoid
optimizing those weird and unlikely scenarios.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1423766494-26150-4-git-send-email-rkrcmar@redhat.com>
[Add comment above KVM_APIC_MODE_* defines. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Broadcast allowed only one global APIC mode, but mixed modes are
theoretically possible. x2APIC IPI doesn't mean 0xff as broadcast,
the rest does.
x2APIC broadcasts are accepted by xAPIC. If we take SDM to be logical,
even addreses beginning with 0xff should be accepted, but real hardware
disagrees. This patch aims for simple code by considering most of real
behavior as undefined.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1423766494-26150-3-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In mixed modes, we musn't deliver xAPIC IPIs like x2APIC and vice versa.
Instead of preserving the information in apic_send_ipi(), we regain it
by converting all destinations into correct MDA in the slow path.
This allows easier reasoning about subsequent matching.
Our kvm_apic_broadcast() had an interesting design decision: it didn't
consider IOxAPIC 0xff as broadcast in x2APIC mode ...
everything worked because IOxAPIC can't set that in physical mode and
logical mode considered it as a message for first 8 VCPUs.
This patch interprets IOxAPIC 0xff as x2APIC broadcast.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1423766494-26150-2-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After speed-up of cpuid_maxphyaddr() it can be called frequently:
instead of heavyweight enumeration of CPUID entries it returns a cached
pre-computed value. It is also inlined now. So caching its result became
unnecessary and can be removed.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150329205644.GA1258@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On each VM-entry CPU should check the following VMCS fields for zero bits
beyond physical address width:
- APIC-access address
- virtual-APIC address
- posted-interrupt descriptor address
This patch adds these checks required by Intel SDM.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150329205627.GA1244@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
cpuid_maxphyaddr(), which performs lot of memory accesses is called
extensively across KVM, especially in nVMX code.
This patch adds a cached value of maxphyaddr to vcpu.arch to reduce the
pressure onto CPU cache and simplify the code of cpuid_maxphyaddr()
callers. The cached value is initialized in kvm_arch_vcpu_init() and
reloaded every time CPUID is updated by usermode. It is obvious that
these reloads occur infrequently.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150329205612.GA1223@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Exposing the on-stack error code with internal error is cheap and
potentially useful.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1428001865-32280-1-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The newly-added tracepoint shows the following results on
the tscdeadline_latency test:
qemu-kvm-8387 [002] 6425.558974: kvm_vcpu_wakeup: poll time 10407 ns
qemu-kvm-8387 [002] 6425.558984: kvm_vcpu_wakeup: poll time 0 ns
qemu-kvm-8387 [002] 6425.561242: kvm_vcpu_wakeup: poll time 10477 ns
qemu-kvm-8387 [002] 6425.561251: kvm_vcpu_wakeup: poll time 0 ns
and so on. This is because we need to go through kvm_vcpu_block again
after the timer IRQ is injected. Avoid it by polling once before
entering kvm_vcpu_block.
On my machine (Xeon E5 Sandy Bridge) this removes about 500 cycles (7%)
from the latency of the TSC deadline timer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename the old __vcpu_run to vcpu_run, and extract part of it to a new
function vcpu_block.
The next patch will add a new condition in vcpu_block, avoid extra
indentation.
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Guest can't be booted w/ ept=0, there is a message dumped as below:
If you're running a guest on an Intel machine without unrestricted mode
support, the failure can be most likely due to the guest entering an invalid
state for Intel VT. For example, the guest maybe running in big real mode
which is not supported on less recent Intel processors.
EAX=00000011 EBX=f000d2f6 ECX=00006cac EDX=000f8956
ESI=bffbdf62 EDI=00000000 EBP=00006c68 ESP=00006c68
EIP=0000d187 EFL=00000004 [-----P-] CPL=0 II=0 A20=1 SMM=0 HLT=0
ES =e000 000e0000 ffffffff 00809300 DPL=0 DS16 [-WA]
CS =f000 000f0000 ffffffff 00809b00 DPL=0 CS16 [-RA]
SS =0000 00000000 ffffffff 00809300 DPL=0 DS16 [-WA]
DS =0000 00000000 ffffffff 00809300 DPL=0 DS16 [-WA]
FS =0000 00000000 ffffffff 00809300 DPL=0 DS16 [-WA]
GS =0000 00000000 ffffffff 00809300 DPL=0 DS16 [-WA]
LDT=0000 00000000 0000ffff 00008200 DPL=0 LDT
TR =0000 00000000 0000ffff 00008b00 DPL=0 TSS32-busy
GDT= 000f6a80 00000037
IDT= 000f6abe 00000000
CR0=00000011 CR2=00000000 CR3=00000000 CR4=00000000
DR0=0000000000000000 DR1=0000000000000000 DR2=0000000000000000 DR3=0000000000000000
DR6=00000000ffff0ff0 DR7=0000000000000400
EFER=0000000000000000
Code=01 1e b8 6a 2e 0f 01 16 74 6a 0f 20 c0 66 83 c8 01 0f 22 c0 <66> ea 8f d1 0f 00 08 00 b8 10 00 00 00 8e d8 8e c0 8e d0 8e e0 8e e8 89 c8 ff e2 89 c1 b8X
X86 eflags bit 1 is fixed set, which means that 1 << 1 is set instead of 1,
this patch fix it.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Message-Id: <1428473294-6633-1-git-send-email-wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the normal return values for bool functions
Signed-off-by: Joe Perches <joe@perches.com>
Message-Id: <9f593eb2f43b456851cd73f7ed09654ca58fb570.1427759009.git.joe@perches.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A trivial code cleanup. This `if` is redundant.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150328222717.GA6508@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some constants are redfined in emulate.c. Avoid it.
s/SELECTOR_RPL_MASK/SEGMENT_RPL_MASK
s/SELECTOR_TI_MASK/SEGMENT_TI_MASK
No functional change.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427635984-8113-3-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The eflags are redefined (using other defines) in emulate.c.
Use the definition from processor-flags.h as some mess already started.
No functional change.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427635984-8113-2-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the source of BSF and BSR is zero, the destination register should not
change. That is how real hardware behaves. If we set the destination even with
the same value that we had before, we may clear bits [63:32] unnecassarily.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427719163-5429-4-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
POPA should assign the values to the registers as usual registers are assigned.
In other words, 32-bits register assignments should clear bits [63:32] of the
register.
Split the code of register assignments that will be used by future changes as
well.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427719163-5429-3-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On legacy mode CMOV emulation should still clear bits [63:32] even if the
assignment is not done. The previous fix 140bad89fd ("KVM: x86: emulation of
dword cmov on long-mode should clear [63:32]") was incomplete.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427719163-5429-2-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If data is read from PIC with invalid access size, the return data stays
uninitialized even though success is returned.
Fix this by always initializing the data.
Signed-off-by: Petr Matousek <pmatouse@redhat.com>
Reported-by: Nadav Amit <nadav.amit@gmail.com>
Message-Id: <20150311111609.GG8544@dhcp-25-225.brq.redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In preparation of adding another tkr field, rename this one to
tkr_mono. Also rename tk_read_base::base_mono to tk_read_base::base,
since the structure is not specific to CLOCK_MONOTONIC and the mono
name got added to the tk_read_base instance.
Lots of trivial churn.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150319093400.344679419@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the guest CPU is supposed to support rdtscp and the host has rdtscp
enabled in the secondary execution controls, we can also expose this
feature to L1. Just extend nested_vmx_exit_handled to properly route
EXIT_REASON_RDTSCP.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
virt/kvm was never really a good include directory for anything else
than locally included headers.
With the move of iodev.h there is no need anymore to add this
directory the compiler's include path, so remove it from the x86 kvm
Makefile.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
iodev.h contains definitions for the kvm_io_bus framework. This is
needed both by the generic KVM code in virt/kvm as well as by
architecture specific code under arch/. Putting the header file in
virt/kvm and using local includes in the architecture part seems at
least dodgy to me, so let's move the file into include/kvm, so that a
more natural "#include <kvm/iodev.h>" can be used by all of the code.
This also solves a problem later when using struct kvm_io_device
in arm_vgic.h.
Fixing up the FSF address in the GPL header and a wrong include path
on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This is needed in e.g. ARM vGIC emulation, where the MMIO handling
depends on the VCPU that does the access.
Signed-off-by: Nikolay Nikolaev <n.nikolaev@virtualopensystems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
An overhead from function call is not appropriate for its size and
frequency of execution.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
kvm_ioapic_update_eoi() wasn't called if directed EOI was enabled.
We need to do that for irq notifiers. (Like with edge interrupts.)
Fix it by skipping EOI broadcast only.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=82211
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
I hit this path on a AMD box and thought
someone was playing a April Fool's joke on me.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch fix the following sparse warnings:
for arch/x86/kvm/x86.c:
warning: symbol 'emulator_read_write' was not declared. Should it be static?
warning: symbol 'emulator_write_emulated' was not declared. Should it be static?
warning: symbol 'emulator_get_dr' was not declared. Should it be static?
warning: symbol 'emulator_set_dr' was not declared. Should it be static?
for arch/x86/kvm/pmu.c:
warning: symbol 'fixed_pmc_events' was not declared. Should it be static?
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
