Starting with the SAMA5D2, there is a new revision of the Atmel PMECC
controller that can correct 32 bits in each sector. This controller is
not 100% compatible with the previous revision that corrected a maximum
of 24 bits by sector, as some register addresses overlap.
Using information from the device tree, we can configure the driver to
work with both versions.
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Do not mention which chips supporting the PMECC controller, as it a
duplicate of the information in the chips' device trees.
Use common terms when describing the sub-node for the NAND Flash
controller.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The NFC controller used to accelerate the NAND transfers on SAMA5 chips
can use either RB_EDGE0 or RB_EDGE3 as its ready/busy interrupt bit.
Use the controller's compatible string to select the correct bit.
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wenyou Yang <Wenyou.yang@atmel.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- Rework and export the changeset API to make it available to users
other than DT overlays
- ARM secure devices binding
- OCTEON USB binding
- Clean-up of various SRAM binding docs
- Various other binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWltcqAAoJEPr7XbWNvGHDDYQP/RbA05cU+CsDpknLS8LgJvpP
BfIT78AeBX38V4vWzl7lGU7cZAEhZG2oljNgPflKZ60g1XCFg6jDjHvt1oU9H+ri
I2I6p5r0k4dXc37X7xYtg02RpGsIpFzyRbM5gRtkwe+TZhFIjsZQazLNIrL6oU8y
0ZNDCheEUMq5oDadYraEWctfp3vNgSAzXlJ4I0IrXwb5hYBtBdAXKw5S3OPYl/m9
lcvoMjw8i8KY97frElZ3DTjjOd11ZTA3L6kwmTdlgmRqUZAMTXVZJiwk787YLGpd
6qjfOURa5/aefltXSS+SG3N6v9AeBgssRYtXy6s09/adqqv6ygSqgGPmxwxSgZOT
gVqZ/ARhlvDlYIqPr6IfLhRLPZQ36GbPZOksMpZH0emQicu5+Uht+bYFFugDgs9f
Zmwa59fmRIBvg10H6+SvaCSXKk3gRtovAdLOLO9HInarmCL7G1VfU1d8O/2fkPQY
drHh/yS7fP91/DvxhN8Z2AKAURqv+BVZhmwGe36+Zucaph3yI8EAQSiypuGvxdHo
e7U08hm1G1kmII38y+RyjqqXQFiXCLZ19QEcTTb1sPIwNfkuCc1rft0bGypqfIjw
KK98TyG7eBAuf53zW8xRojGeYyku/w2GRsrGWdJrgVqghsy4INbBXkzLXDj14i7O
BiPisfrIyAqViqWGI6eJ
=LW4w
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- Rework and export the changeset API to make it available to users
other than DT overlays
- ARM secure devices binding
- OCTEON USB binding
- Clean-up of various SRAM binding docs
- Various other binding doc updates
* tag 'devicetree-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (21 commits)
drivers/of: Export OF changeset functions
Fix documentation for adp1653 DT
ARM: psci: Fix indentation in DT bindings
of/platform: export of_default_bus_match_table
of/unittest: Show broken behaviour in the platform bus
of: fix declaration of of_io_request_and_map
of/address: replace printk(KERN_ERR ...) with pr_err(...)
of/irq: optimize device node matching loop in of_irq_init()
dt-bindings: tda998x: Document the required 'port' node.
net/macb: bindings doc: Merge cdns-emac to macb
dt-bindings: Misc fix for the ATH79 DDR controllers
dt-bindings: Misc fix for the ATH79 MISC interrupt controllers
Documentation: dt: Add bindings for Secure-only devices
dt-bindings: ARM: add arm,cortex-a72 compatible string
ASoC: Atmel: ClassD: add GCK's parent clock in DT binding
DT: add Olimex to vendor prefixes
Documentation: fsl-quadspi: Add fsl,ls1021-qspi compatible string
Documentation/devicetree: document OCTEON USB bindings
usb: misc: usb3503: Describe better how to bind clock to the hub
dt-bindings: Consolidate SRAM bindings from all vendors
...
Add DT bindings for NAND devices connected to the NEMC on JZ4780 SoCs,
as well as the hardware BCH controller, used by the jz4780_{nand,bch}
drivers.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add device tree binding for NAND on the BCM6368.
The BCM6368 has a NAND interrupt register with combined status and enable
registers. It also requires a clock, so add an optional clock to the
common brcmnand binding.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As noted here [1], there are potentially future conflicts if we try to
use MTD's "partitions" subnode to describe anything besides just the
fixed-in-the-device-tree partitions currently described in this
document. Particularly, there was a proposal to use this node for the
AFS parser too.
It can pose a (small) problem to try to differentiate the following
nodes:
// using binding as currently specified
partitions {
#address-cells = <x>;
#size-cells = <y>;
partition@0 {
...;
};
};
and
// proposed future binding
partitions {
compatible = "arm,arm-flash-structure";
};
It's especially difficult if other uses of this node start having
subnodes.
So, since the "partitions" node is new in v4.4, let's fixup the binding
before release so that it requires a compatible property, so it's much
clearer to distinguish. e.g.:
// proposed
partitions {
compatible = "fixed-partitions";
#address-cells = <x>;
#size-cells = <y>;
partition@0 {
...;
};
};
[1] Subject: "mtd: create a partition type device tree binding"
http://lkml.kernel.org/g/20151113220039.GA74382@google.comhttp://lists.infradead.org/pipermail/linux-mtd/2015-November/063355.htmlhttp://lists.infradead.org/pipermail/linux-mtd/2015-November/063364.html
Cc: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Pull the supported chip names from drivers/mtd/devices/m25p80.c and stop
pointing readers to Linux code.
Also (although I see this habit repeated throughout the
Documentation/devicetree/bindings/ tree), stop using the title "driver"
in this file, when we're trying explicitly to describe hardware, not
software.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Add device tree binding documentation for serial flash with
Mediatek serial flash controller
Signed-off-by: Bayi Cheng <bayi.cheng@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
[Brian: fixed up language]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The lock flag of ofpart is undocumented. Add to binding doc.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
To avoid conflict with other drivers using subnodes of the mtd device
create only one ofpart-specific node rather than any number of
arbitrary partition subnodes.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC
strength. The SPEAr600 HW ECC only supports 1-bit ECC strength.
To enable SW BCH4, you need to specify this in your nand controller
DT node:
nand-ecc-mode = "soft_bch";
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
Tested on a custom SPEAr600 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
[Brian: tweaked the comments a bit]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
SPI NOR
* reduce virtual address space requirements for fsl-quadspi memory map
* new fsl-quadspi IP support: imx6ul-qspi and imx7d-qspi
* add new NOR flash device support
* add new driver for NXP SPI Flash Interface (SPIFI)
* stop abusing SPI API structs for non-SPI framework
* fixup DT table matching for new "jedec,spi-nor" string
NAND
* brcmnand: fix big endian MIPS macro usage
* denali: refactor to use devres, dev_*() printing, etc.
* OMAP ELM: change the module alias to actually be usable
* pxa3xx_nand: fixup a few command sequencing issues -- both new and old
- race conditions in the IRQ handler status clearing
- problems when a bootloader left interrupts pending
- config issues when overriding the bootloader configuration
* new flash device support
* sunxi_nand:
- optimize timing configuration by calculation, rather than fixed
fail-safe values
- use EDO setting from ONFI
* r852: fix compiler warnings
* davinci: add 4KB page support
Core
* oobtest: correct debug print information
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vpBS
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150901' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"SPI NOR:
- reduce virtual address space requirements for fsl-quadspi memory map
- new fsl-quadspi IP support: imx6ul-qspi and imx7d-qspi
- add new NOR flash device support
- add new driver for NXP SPI Flash Interface (SPIFI)
- stop abusing SPI API structs for non-SPI framework
- fixup DT table matching for new "jedec,spi-nor" string
NAND:
- brcmnand: fix big endian MIPS macro usage
- denali: refactor to use devres, dev_*() printing, etc.
- OMAP ELM: change the module alias to actually be usable
- pxa3xx_nand: fixup a few command sequencing issues -- both new and old
- race conditions in the IRQ handler status clearing
- problems when a bootloader left interrupts pending
- config issues when overriding the bootloader configuration
- new flash device support
- sunxi_nand:
- optimize timing configuration by calculation, rather than fixed
fail-safe values
- use EDO setting from ONFI
- r852: fix compiler warnings
- davinci: add 4KB page support
Core:
- oobtest: correct debug print information"
* tag 'for-linus-20150901' of git://git.infradead.org/linux-mtd: (42 commits)
mtd: mtd_oobtest: Fix the address offset with vary_offset case
mtd: blkdevs: fix switch-bool compilation warning
mtd: spi-nor: stop (ab)using struct spi_device_id
mtd: nand: add Toshiba TC58NVG0S3E to nand_ids table
mtd: dataflash: Export OF module alias information
nand: pxa3xx: Increase READ_ID buffer and make the size static
mtd: nand: pxa3xx-nand: fix random command timeouts
mtd: nand: pxa3xx_nand: fix early spurious interrupt
mtd: pxa3xx_nand: add a default chunk size
mtd: omap_elm: Fix module alias
mtd: physmap_of: fix null pointer deference when kzalloc returns null
mtd: nettel: do not ignore mtd_device_register() failure in nettel_init()
mtd: denali_pci: switch to dev_err()
mtd: denali_pci: refactor driver using devres API
mtd: denali_pci: use module_pci_driver() macro
mtd: denali: hide core part from user in Kconfig
mtd: spi-nor: add Spansion S25FL204K support
mtd: spi-nor: Improve Kconfig help text for SPI_FSL_QUADSPI
mtd: spi-nor: add driver for NXP SPI Flash Interface (SPIFI)
doc: dt: add documentation for nxp,lpc1773-spifi
...
The PXA architecture provides a DMA to pump data from the nand
controller to memory and the other way around. Add it to the binding
description.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Rob Herring <robh@kernel.org>
Add device tree binding documentation for the SPI Flash Interface
(SPIFI) found on NXP LPC18xx and LPC43xx devies.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add notes to describe how some SoCs integrate this NAND core a little
differently, and so we define extra compatibility strings and register
resources/names.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
In commit 8ff16cf77c ("Documentation: devicetree: m25p80: add "nor-jedec"
binding"), we added a generic "nor-jedec" binding to catch all
mostly-compatible SPI NOR flash which can be detected via the READ ID
opcode (0x9F). This was discussed and reviewed at the time, however
objections have come up since then as part of this discussion:
http://lkml.kernel.org/g/20150511224646.GJ32500@ld-irv-0074
It seems the parties involved agree that "jedec,spi-nor" does a better
job of capturing the fact that this is SPI-specific, not just any NOR
flash.
This binding was only merged for v4.1-rc1, so it's still OK to change
the naming.
At the same time, let's move the documentation to a better name.
Next up: stop referring to code (drivers/mtd/devices/m25p80.c) from the
documentation.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Almost all flash that are "compatible" with m25p80 support the JEDEC
READ ID opcode (0x9F), and in fact, that is often the only thing that is
used to differentiate them. Let's add a compatible string that
represents this lowest common denominator of compatibility.
Device trees can still specify manufacturer/device names in addition,
but (until some reason is found to differentiate between them through
device tree) software will likely want to bind just against the generic
name, and avoid unnecessarily growing its device ID binding tables.
This is related to the work of commit a5b7616c55 ("mtd:
m25p80,spi-nor: Fix module aliases for m25p80"), which showed that
maintaining these device tables as stable device-tree/modalias binding
tables is not a worthwhile burden for mostly-comptatible flash.
At the same time, let's update the binding doc to point to the
m25p_ids[] ID list instead of spi_nor_ids[]. The former can be used for
device tree bindings, but the latter cannot. In the future, we should
pare down the m25p_ids[] list to only those IDs which are actually used
in device trees.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
NAND:
* Add new Hisilicon NAND driver for Hip04
* Add default reboot handler, to ensure all outstanding erase transactions
complete in time
* jz4740: convert to use GPIO descriptor API
* Atmel: add support for sama5d4
* Change default bitflip threshold to 75% of correction strength
* Miscellaneous cleanups and bugfixes
SPI NOR:
* Freescale QuadSPI:
- Fix a few probe() and remove() issues
- Add a MAINTAINERS entry for this driver
- Tweak transfer size to increase read performance
- Add suspend/resume support
* Add Micron quad I/O support
* ST FSM SPI: miscellaneous fixes
JFFS2:
* gracefully handle corrupted 'offset' field found on flash
Other:
* bcm47xxpart: add tweaks for a few new devices
* mtdconcat: set return lengths properly for mtd_write_oob()
* map_ram: enable use with mtdoops
* maps: support fallback to ROM/UBI for write-protected NOR flash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+nRk
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150216' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND:
- Add new Hisilicon NAND driver for Hip04
- Add default reboot handler, to ensure all outstanding erase
transactions complete in time
- jz4740: convert to use GPIO descriptor API
- Atmel: add support for sama5d4
- Change default bitflip threshold to 75% of correction strength
- Miscellaneous cleanups and bugfixes
SPI NOR:
- Freescale QuadSPI:
- Fix a few probe() and remove() issues
- Add a MAINTAINERS entry for this driver
- Tweak transfer size to increase read performance
- Add suspend/resume support
- Add Micron quad I/O support
- ST FSM SPI: miscellaneous fixes
JFFS2:
- gracefully handle corrupted 'offset' field found on flash
Other:
- bcm47xxpart: add tweaks for a few new devices
- mtdconcat: set return lengths properly for mtd_write_oob()
- map_ram: enable use with mtdoops
- maps: support fallback to ROM/UBI for write-protected NOR flash"
* tag 'for-linus-20150216' of git://git.infradead.org/linux-mtd: (46 commits)
mtd: hisilicon: && vs & typo
jffs2: fix handling of corrupted summary length
mtd: hisilicon: add device tree binding documentation
mtd: hisilicon: add a new NAND controller driver for hisilicon hip04 Soc
mtd: avoid registering reboot notifier twice
mtd: concat: set the return lengths properly
mtd: kconfig: replace PPC_OF with PPC
mtd: denali: remove unnecessary stubs
mtd: nand: remove redundant local variable
MAINTAINERS: add maintainer entry for FREESCALE QUAD SPI driver
mtd: fsl-quadspi: improve read performance by increase AHB transfer size
mtd: fsl-quadspi: Remove unnecessary 'map_failed' label
mtd: fsl-quadspi: Remove unneeded success/error messages
mtd: fsl-quadspi: Fix the error paths
mtd: nand: omap: drop condition with no effect
mtd: nand: jz4740: Convert to GPIO descriptor API
mtd: nand: Request strength instead of bytes for soft BCH
mtd: nand: default bitflip-reporting threshold to 75% of correction strength
mtd: atmel_nand: introduce a new compatible string for sama5d4 chip
mtd: atmel_nand: return max bitflips in all sectors in pmecc_correction()
...
This patch adds the related dts binding document for Hisilicon 504 NAND
controller.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch fix multiple words such as "the the" and "which which"
in Documentation/devicetree.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Since in SAMA5D4 chip, the PMECC can correct bit flips in erased page.
So we add a DT property to indicate this hardware character.
If the PMECC support correct bitflip erased page (all data are 0xff).
Then we can use the PMECC correct the page and skip the erased page
check.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
UBI needs to know the physical erase block size, even on read-only
devices, since it defines the on-device layout. Use a device-tree
provided value to support previously written UBI on read-only NOR.
UBI also needs a non-zero writebufsize, so we set it to one.
Note: This was implemented because hardware write-protected CFI
NOR cannot be probed for the physical erase block size.
Signed-off-by: Joe Schultz <jschultz@xes-inc.ccom>
Signed-off-by: Aaron Sierra <asierra@xes-inc.ccom>
[Brian: removed unneeded #ifdef, note 'optional' erase-size property]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
"fsl,imx6sx-qspi" is also a valid compatible string, so add an entry for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This sentence "We support only one NAND chip now" is not true any more.
Multiple chips are supported. So lets remove this sentence to not
confuse anyone.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Huang Shijie <b32955@freescale.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If there is no PMECC lookup table stored in ROM, or lookup table offset is
not specified, PMECC driver should build it in DDR by itself.
That make the PMECC driver work for some board which doesn't have PMECC
lookup table in ROM.
The PMECC use the BCH algorithm, so based on the build_gf_tables()
function in lib/bch.c, we can build the Galois Field lookup table.
For more information can refer to section 5.4 of PMECC controller
application note:
http://www.atmel.com/images/doc11127.pdf
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Expand the description of the 'gpios' property in the GPIO assisted
NAND flash binding, to explicitly list the required GPIO pin references
and their order.
Update the example section to individually bracket the GPIO references,
and capitalize the signal names for improved readability.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add documentation for the sandisk docg3 chip.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
NAND
* Cleanup for Denali driver
* Atmel: add support for new page sizes
* Atmel: fix up 'raw' mode support
* Atmel: miscellaneous cleanups
* New timing mode helpers for non-ONFI NAND
* OMAP: allow driver to be (properly) built as a module
* bcm47xx: RESET support and other cleanups
SPI NOR
* Miscellaneous cleanups, to prepare framework for wider use (some further
work still pending)
* Compile-time configuration to select 4K vs. 64K support for flash that
support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/jCH
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd
Pull MTD update from Brian Norris:
"Sorry for delaying this a bit later than usual. There's one mild
regression from 3.16 that was noticed during the 3.17 cycle, and I
meant to send a fix for it along with this pull request. I'll
probably try to queue it up for a later pull request once I've had a
better look at it, hopefully by -rc2 at the latest.
Summary for this pull:
NAND
- Cleanup for Denali driver
- Atmel: add support for new page sizes
- Atmel: fix up 'raw' mode support
- Atmel: miscellaneous cleanups
- New timing mode helpers for non-ONFI NAND
- OMAP: allow driver to be (properly) built as a module
- bcm47xx: RESET support and other cleanups
SPI NOR
- Miscellaneous cleanups, to prepare framework for wider use (some
further work still pending)
- Compile-time configuration to select 4K vs. 64K support for flash
that support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more"
* tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd: (59 commits)
mtd: nand: omap: Correct CONFIG_MTD_NAND_OMAP_BCH help message
mtd: nand: Force omap_elm to be built as a module if omap2_nand is a module
mtd: move support for struct flash_platform_data into m25p80
mtd: spi-nor: add Kconfig option to disable 4K sectors
mtd: nand: Move ELM driver and rename as omap_elm
nand: omap2: Replace pr_err with dev_err
nand: omap2: Remove horrible ifdefs to fix module probe
mtd: nand: add Hynix's H27UCG8T2ATR-BC to nand_ids table
mtd: nand: support ONFI timing mode retrieval for non-ONFI NANDs
mtd: physmap_of: Add non-obsolete map_rom probe
mtd: physmap_of: Fix ROM support via OF
MAINTAINERS: add l2-mtd.git, 'next' tree for MTD
mtd: denali: fix indents and other trivial things
mtd: denali: remove unnecessary parentheses
mtd: denali: remove another set-but-unused variable
mtd: denali: fix include guard and license block of denali.h
mtd: nand: don't break long print messages
mtd: bcm47xxnflash: replace some magic numbers
mtd: bcm47xxnflash: NAND_CMD_RESET support
mtd: bcm47xxnflash: add cmd_ctrl handler
...
Previously, the only way to map a NOR device as a simple ROM was to
use the obsolete "direct-mapped" compatible binding (which further
requires device_type = "nor" and probe-type = "NOR" properties).
This patch adds an "mtd-rom" compatible binding to the "map_rom"
probe type.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Retrieve the NFC clock to make sure it is enabled. Make that optional to ensure
compatibility with previous device trees but document it as mandatory so newer
device trees will include it.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For v3.14 and prior, 1-bit Hamming code ECC via software was the
default choice for some boards e.g. 3430sdp.
Commit ac65caf514 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So don't mark "sw" scheme
as deperecated and support it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With a flash-based BBT there is no reason to move the Factory Bad
Block Marker from the data area buffer (to where it is mapped by the
GPMI NAND controller) to the OOB buffer. Thus, make this feature
configurable via DT. This is required for the Ka-Ro electronics
platforms.
In the original code 'this->swap_block_mark' was synonymous with
'!GPMI_IS_MX23()', so use the latter at the relevant places.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- refactor m25p80.c driver for use as a general SPI NOR framework for other
drivers which may speak to SPI NOR flash without providing full SPI support
(i.e., not part of drivers/spi/)
- new Freescale QuadSPI driver (utilizing new SPI NOR framework)
- updates for the STMicro "FSM" SPI NOR driver
- fix sync/flush behavior on mtd_blkdevs
- fixup subpage write support on a few NAND drivers
- correct the MTD OOB test for odd-sized OOB areas
- add BCH-16 support for OMAP NAND
- fix warnings and trivial refactoring
- utilize new ECC DT bindings in pxa3xx NAND driver
- new LPDDR NVM driver
- address a few assorted bugs caught by Coverity
- add new imx6sx support for GPMI NAND
- use a bounce buffer for NAND when non-DMA-able buffers are used
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6UIq
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
- refactor m25p80.c driver for use as a general SPI NOR framework for
other drivers which may speak to SPI NOR flash without providing full
SPI support (i.e., not part of drivers/spi/)
- new Freescale QuadSPI driver (utilizing new SPI NOR framework)
- updates for the STMicro "FSM" SPI NOR driver
- fix sync/flush behavior on mtd_blkdevs
- fixup subpage write support on a few NAND drivers
- correct the MTD OOB test for odd-sized OOB areas
- add BCH-16 support for OMAP NAND
- fix warnings and trivial refactoring
- utilize new ECC DT bindings in pxa3xx NAND driver
- new LPDDR NVM driver
- address a few assorted bugs caught by Coverity
- add new imx6sx support for GPMI NAND
- use a bounce buffer for NAND when non-DMA-able buffers are used
* tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd: (77 commits)
mtd: gpmi: add gpmi support for imx6sx
mtd: maps: remove check for CONFIG_MTD_SUPERH_RESERVE
mtd: bf5xx_nand: use the managed version of kzalloc
mtd: pxa3xx_nand: make the driver work on big-endian systems
mtd: nand: omap: fix omap_calculate_ecc_bch() for-loop error
mtd: nand: r852: correct write_buf loop bounds
mtd: nand_bbt: handle error case for nand_create_badblock_pattern()
mtd: nand_bbt: remove unused variable
mtd: maps: sc520cdp: fix warnings
mtd: slram: fix unused variable warning
mtd: pfow: remove unused variable
mtd: lpddr: fix Kconfig dependency, for I/O accessors
mtd: nand: pxa3xx: Add supported ECC strength and step size to the DT binding
mtd: nand: pxa3xx: Use ECC strength and step size devicetree binding
mtd: nand: pxa3xx: Clean pxa_ecc_init() error handling
mtd: nand: Warn the user if the selected ECC strength is too weak
mtd: nand: omap: Documentation: How to select correct ECC scheme for your device ?
mtd: nand: omap: add support for BCH16_ECC - NAND driver updates
mtd: nand: omap: add support for BCH16_ECC - ELM driver updates
mtd: nand: omap: add support for BCH16_ECC - GPMC driver updates
...
Pull trivial tree changes from Jiri Kosina:
"Usual pile of patches from trivial tree that make the world go round"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
staging: go7007: remove reference to CONFIG_KMOD
aic7xxx: Remove obsolete preprocessor define
of: dma: doc fixes
doc: fix incorrect formula to calculate CommitLimit value
doc: Note need of bc in the kernel build from 3.10 onwards
mm: Fix printk typo in dmapool.c
modpost: Fix comment typo "Modules.symvers"
Kconfig.debug: Grammar s/addition/additional/
wimax: Spelling s/than/that/, wording s/destinatary/recipient/
aic7xxx: Spelling s/termnation/termination/
arm64: mm: Remove superfluous "the" in comment
of: Spelling s/anonymouns/anonymous/
dma: imx-sdma: Spelling s/determnine/determine/
ath10k: Improve grammar in comments
ath6kl: Spelling s/determnine/determine/
of: Improve grammar for of_alias_get_id() documentation
drm/exynos: Spelling s/contro/control/
radio-bcm2048.c: fix wrong overflow check
doc: printk-formats: do not mention casts for u64/s64
doc: spelling error changes
...
This commit updates the devicetree binding documentation for this driver
with the supported ECC strength and step size combinations.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The m25p80.c has used the SPI NOR framework now, and the m25p_ids has
been moved to spi-nor.c and renamed to spi_nor_ids.
This patch updates the document for m25p80.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds the binding file for Freescale QuadSPI driver.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: devicetree@vger.kernel.org
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some flashes can only be properly accessed when the ECC mode is
specified, so a way to describe such mode is required.
Together, the ECC strength and step size define the correction capability,
so that we say we will correct "{strength} bit errors per {size} bytes".
The interpretation of these parameters is implementation-defined, but they
often have ramifications on the formation, interpretation, and placement of
correction metadata on the flash. Not all implementations must support all
possible combinations. Implementations are encouraged to further define the
value(s) they support.
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Keystone arch has compatible nand device, so reuse it.
In case with Keystone it depends on TI_AEMIF because AEMIF
driver is responsible to set timings.
See http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The properties davinci-ecc-mode, davinci-nand-use-bbt, davinci-nand-buswidth
are MTD generic. Correct names for them are: nand-ecc-mode, nand-on-flash-bbt,
nand-bus-width accordingly. So rename them in dts and documentation.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Extend bindings for davinci_nand driver to be more clear.
This is clarification only, without semantic changes.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Move bindings under mtd. Do this in order to make davinci-nand
driver usable by keystone architecture.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for flash-based bad block table using Marvell's
custom in-flash bad block table layout. The support is enabled
a 'flash_bbt' platform data or device tree parameter.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since the driver supports the new compatible string, the binding
documentation must be updated to reflect it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In default way, we use the ecc_strength/ecc_step size calculated by ourselves
and use all the OOB area.
This patch adds a new property : "fsl,use-minimum-ecc"
If we enable it, we will firstly try to use the datasheet's minimum required
ECC provided by the MTD layer (the ecc_strength_ds/ecc_step_ds fields
in the nand_chip{}). So we may have free space in the OOB area by using the
minimum ECC, and we may support JFFS2 with some SLC NANDs, such as Micron's
SLC NAND.
If we fail to use the minimum ECC, we will use the legacy method to calculate
the ecc_strength and ecc_step size.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
OMAP NAND driver support multiple ECC scheme, which can used in different
flavours, depending on in-build Hardware engines present on SoC.
This patch updates following in DT bindings related to sectionion of ecc-schemes
- ti,elm-id: replaces elm_id (maintains backward compatibility)
- ti,nand-ecc-opts: selection of h/w or s/w implementation of an ecc-scheme
depends on ti,elm-id. (supported values ham1, bch4, and bch8)
- maintain backward compatibility to deprecated DT bindings (sw, hw, hw-romcode)
Below table shows different flavours of ecc-schemes supported by OMAP devices
+---------------------------------------+---------------+---------------+
| ECC scheme |ECC calculation|Error detection|
+---------------------------------------+---------------+---------------+
|OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W |
|(requires CONFIG_MTD_NAND_ECC_BCH) | | |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) |
|(requires CONFIG_MTD_NAND_OMAP_BCH && | | |
| ti,elm-id in DT) | | |
+---------------------------------------+---------------+---------------+
To optimize footprint of omap2-nand driver, selection of some ECC schemes
also require enabling following Kconfigs, in addition to setting appropriate
DT bindings
- Kconfig:CONFIG_MTD_NAND_ECC_BCH error detection done in software
- Kconfig:CONFIG_MTD_NAND_OMAP_BCH error detection done by h/w engine
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In case that the nand device will support some features like Nand Flash
Controller, we want to make the sub feature as a sub node of nand device.
Use such organization it is easy to enable/disable feature, also it is back
compatible and more readable.
If the sub-node has a compatible property then it is a driver not partition.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[ added a missing newline -Brian ]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch enable writing nand flash via NFC SRAM. It will minimize the CPU
overhead. The SRAM write only support ECC_NONE and ECC_HW with PMECC.
To enable this NFC write by SRAM feature, you can add a string in dts under
NFC driver node.
This driver has been tested on SAMA5D3X-EK with JFFS2, YAFFS2, UBIFS and
mtd-utils.
Here is part of mtd_speedtest (writing test) result, compare with non-NFC
writing, it reduces %65 cpu load with loss %12 speed.
- commands use to test:
# insmod /mnt/mtd_speedtest.ko dev=2 &
# top -n 30 -d 1 | grep speedtest
- test result:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: MTD device size 41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64
mtd_speedtest: testing eraseblock write speed
509 495 root D 1164 0% 7% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 8% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root R 1164 0% 5% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: eraseblock write speed is 5194 KiB/s
mtd_speedtest: testing page write speed
509 495 root D 1164 0% 32% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 27% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 25% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 30% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: page write speed is 5024 KiB/s
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch will set the nand dma support in dts. Since we will not use
cpu_is_xxx() in nand driver. We needn't include the mach/cpu.h any more.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add nand bank selection and timings to the device tree bindings.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
[Added some documentation]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
OMAP devices support various NAND transfer modes.
Currently all device-tree definitions will use the default "prefetch
polled" mode, so this patch enables the transfer mode to be specified
in the device-tree.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Few GPMC fixes and binding doc updates noted after sending
pull requests for the GPMC branch.
- Board fixes for beagle usb host and rx51 spi probe order
- SoC fixes dt earlyprintk, omap1 dma and omap2+ id.c error
handling fixes
Then few minor things that are not strictly fixes but are good
to get out of the way:
- Add missing legacy mux registers for am/dm73x gpio
- Add detection for am33xx pg2.1 silicon
- Enable twl4030 audio modules in defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lnij
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Omap fixes for things that were discovered during the merge window:
- Few GPMC fixes and binding doc updates noted after sending
pull requests for the GPMC branch.
- Board fixes for beagle usb host and rx51 spi probe order
- SoC fixes dt earlyprintk, omap1 dma and omap2+ id.c error
handling fixes
Then few minor things that are not strictly fixes but are good
to get out of the way:
- Add missing legacy mux registers for am/dm73x gpio
- Add detection for am33xx pg2.1 silicon
- Enable twl4030 audio modules in defconfig
* tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove bogus IS_ERR_OR_NULL checking from id.c
ARM: OMAP4+: omap2plus_defconfig: Enable audio via TWL6040 as module
ARM: OMAP2: AM33XX: id: Add support for new AM335x PG2.1 Si
omap: mux: add AM/DM37x gpios
ARM: OMAP1: DMA: fix error handling in omap1_system_dma_init()
ARM: OMAP2+: omap_device: use late_initcall_sync
ARM: OMAP: RX-51: change probe order of touchscreen and panel SPI devices
ARM: OMAP3: Beagle: Fix USB Host on beagle xM Ax/Bx
ARM: OMAP2+: only WARN if a GPMC child probe function fail
ARM: OMAP2+: only search for GPMC DT child nodes on probe
Documentation: dt: update properties in TI GPMC NAND example
Documentation: dt: update TI GPMC ethernet binding properties
Signed-off-by: Olof Johansson <olof@lixom.net>
- Support partitions larger than 4GiB in device tree
- Support for new SPI chips
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iEYEABECAAYFAlGLxzEACgkQdwG7hYl686M+PgCdHAn3fDzGW7gUL1tj43NCqaC8
PWoAoNAD5YpI3wYEBxped2MjSfgbQMvq
=hM2T
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd
Pull MTD update from David Woodhouse:
- Lots of cleanups from Artem, including deletion of some obsolete
drivers
- Support partitions larger than 4GiB in device tree
- Support for new SPI chips
* tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd: (83 commits)
mtd: omap2: Use module_platform_driver()
mtd: bf5xx_nand: Use module_platform_driver()
mtd: denali_dt: Remove redundant use of of_match_ptr
mtd: denali_dt: Change return value to fix smatch warning
mtd: denali_dt: Use module_platform_driver()
mtd: denali_dt: Fix incorrect error check
mtd: nand: subpage write support for hardware based ECC schemes
mtd: omap2: use msecs_to_jiffies()
mtd: nand_ids: use size macros
mtd: nand_ids: improve LEGACY_ID_NAND macro a bit
mtd: add 4 Toshiba nand chips for the full-id case
mtd: add the support to parse out the full-id nand type
mtd: add new fields to nand_flash_dev{}
mtd: sh_flctl: Use of_match_ptr() macro
mtd: gpio: Use of_match_ptr() macro
mtd: gpio: Use devm_kzalloc()
mtd: davinci_nand: Use of_match_ptr()
mtd: dataflash: Use of_match_ptr() macro
mtd: remove h720x flash support
mtd: onenand: remove OneNAND simulator
...
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
The GPMC timing properties for device-tree have been updated
by adding a "-ns" or "-ps" suffix to indicate the units of
time the property represents. Therefore, update the timing
property names for TI GPMC NAND example.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Previously, partitions were limited to less than 4 GiB in size because
the address and size were read as 32-bit values. Add support for 64-bit
values to support devices of 4 GiB and larger.
Signed-off-by: Joe Schaack <jschaack@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With the generic DMA device tree helper supported by mxs-dma driver,
client devices only need to call dma_request_slave_channel() for
requesting a DMA channel from dmaengine.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
When booting with device-tree, retrieve GPMC settings for ONENAND from
the device-tree blob. This will allow us to remove all static settings
stored in the gpmc-nand.c in the future once the migration to
device-tree is complete.
The user must now specify the ONENAND device width in the device-tree
binding so that the GPMC can be programmed correctly. Therefore, update
the device-tree binding documentation for ONENAND devices connected to
the GPMC to reflect this.
Please note that this does not include GPMC timings for ONENAND. The
timings are being calculated at runtime.
There is some legacy code that only enables read wait monitoring for
non-OMAP3 devices. There are no known OMAP3 device issues that prevent
this feature being enabled and so when booting with device-tree use the
wait-monitoring settings described in the device-tree blob.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
NOR flash is not currently supported when booting with device-tree
on OMAP2+ devices. Add support to detect and configure NOR devices
when booting with device-tree.
Add documentation for the TI GPMC NOR binding.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
* misc clean-ups in the MTD command-line partitioning parser (cmdlinepart)
* add flash locking support for STmicro chips serial flash chips, as well as
for CFI command set 2 chips.
* new driver for the ELM error correction HW module found in various TI chips,
enable the OMAP NAND driver to use the ELM HW error correction
* added number of new serial flash IDs
* various fixes and improvements in the gpmi NAND driver
* bcm47xx NAND driver improvements
* make the mtdpart module actually removable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iEYEABECAAYFAlExEs8ACgkQdwG7hYl686Oa+gCgiBNt+I0MiixDeN+MGuE1uw9s
i2wAniD9sR2HDy6y5SkbdXK/aPr8ez/p
=xV1l
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd
Pull MTD update from David Woodhouse:
"Fairly unexciting MTD merge for 3.9:
- misc clean-ups in the MTD command-line partitioning parser
(cmdlinepart)
- add flash locking support for STmicro chips serial flash chips, as
well as for CFI command set 2 chips.
- new driver for the ELM error correction HW module found in various
TI chips, enable the OMAP NAND driver to use the ELM HW error
correction
- added number of new serial flash IDs
- various fixes and improvements in the gpmi NAND driver
- bcm47xx NAND driver improvements
- make the mtdpart module actually removable"
* tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd: (45 commits)
mtd: map: BUG() in non handled cases
mtd: bcm47xxnflash: use pr_fmt for module prefix in messages
mtd: davinci_nand: Use managed resources
mtd: mtd_torturetest can cause stack overflows
mtd: physmap_of: Convert device allocation to managed devm_kzalloc()
mtd: at91: atmel_nand: for PMECC, add code to check the ONFI parameter ECC requirement.
mtd: atmel_nand: make pmecc-cap, pmecc-sector-size in dts is optional.
mtd: atmel_nand: avoid to report an error when lookup table offset is 0.
mtd: bcm47xxsflash: adjust names of bus-specific functions
mtd: bcm47xxpart: improve probing of nvram partition
mtd: bcm47xxpart: add support for other erase sizes
mtd: bcm47xxnflash: register this as normal driver
mtd: bcm47xxnflash: fix message
mtd: bcm47xxsflash: register this as normal driver
mtd: bcm47xxsflash: write number of written bytes
mtd: gpmi: add sanity check for the ECC
mtd: gpmi: set the Golois Field bit for mx6q's BCH
mtd: devices: elm: Removes <xx> literals in elm DT node
mtd: gpmi: fix a dereferencing freed memory error
mtd: fix the wrong timeo for panic_nand_wait()
...
These are device tree conversions for a number of platforms,
with the intention of turning code from board files into
device tree descriptions. Notable changes are:
* davinci bindings for pinctrl, MTD, RTC, watchdog and i2c
* nomadik bindings for all devices, removing the board files
* bcm2835 bindings for mmc and i2c
* tegra bindings for hdmi, keyboard, audio, as well as some updates
* at91 bindings for hardware ecc and for devices on RM9200
* mxs bindings for cfa100xx
* sunxi support for Miniand Hackberry board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=NLEa
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree conversions from Arnd Bergmann:
"These are device tree conversions for a number of platforms, with the
intention of turning code from board files into device tree
descriptions. Notable changes are:
- davinci bindings for pinctrl, MTD, RTC, watchdog and i2c
- nomadik bindings for all devices, removing the board files
- bcm2835 bindings for mmc and i2c
- tegra bindings for hdmi, keyboard, audio, as well as some updates
- at91 bindings for hardware ecc and for devices on RM9200
- mxs bindings for cfa100xx
- sunxi support for Miniand Hackberry board"
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (72 commits)
Revert "sunxi: a10-cubieboard: Add user LEDs to the device tree"
Revert "sunxi: a13-olinuxino: Add user LED to the device tree"
clk: tegra: initialise parent of uart clocks
ARM: tegra: remove clock-frequency properties from serial nodes
clk: tegra: fix driver to match DT binding
clk: tegra: local arrays should be static
clk: tegra: Add missing spinlock for hclk and pclk
clk: tegra: Implement locking for super clock
clk: tegra: fix wrong clock index between se to sata_cold
sunxi: a13-olinuxino: Add user LED to the device tree
ARM: davinci: da850 DT: add support for machine reboot
ARM: davinci: da850: add wdt DT node
ARM: davinci: da850: add DT node for I2C0
ARM: at91: at91sam9n12: add DT parameters to enable PMECC
ARM: at91: at91sam9x5: add DT parameters to enable PMECC
ARM: at91: add EMAC bindings to RM9200 DT
ARM: at91: add SSC bindings to RM9200 DT
ARM: at91: add MMC bindings to RM9200 DT
ARM: at91: Animeo IP: enable watchdog support
ARM: nomadik: fix OF compilation regression
...
As part of removing generalized dependency, replace <xx> literal fields
in DT compatible field with <52> for am335x platforms.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Currently cfi_cmdset_0002.c does not support PPB locking of sectors. This
patch adds support for this locking/unlocking mechanism. It is needed on
some platforms, since newer U-Boot versions do support this PPB locking
and protect for example their environment sector(s) this way.
This PPB locking/unlocking will be enabled for all devices supported by
cfi_cmdset_0002 reporting 8 in the CFI word 0x49 (Sector Protect/Unprotect
scheme).
Please note that PPB locking does support sector-by-sector locking. But
the whole chip can only be unlocked together. So unlocking one sector
will automatically unlock all sectors of this device. Because of this
chip limitation, the PPB unlocking function saves the current locking
status of all sectors before unlocking the whole device. After unlocking
the saved locking status is re-configured. This way only the addressed
sectors will be unlocked.
To selectively enable this advanced sector protection mechanism, the
device-tree property "use-advanced-sector-protection" has been created.
To enable support for this locking this property needs to be present in the
flash DT node. E.g.:
nor_flash@0,0 {
compatible = "amd,s29gl256n", "cfi-flash";
bank-width = <2>;
use-advanced-sector-protection;
...
Tested with Spansion S29GL512S10THI and Micron JS28F512M29EWx flash
devices.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The ELM hardware module can be used to speedup BCH 4/8/16 ECC scheme
error correction.
For now only 4 & 8 bit support is added
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
In case ELM module available, omap2 NAND driver can opt for hardware
correction method for bit flip errors in NAND flash with BCH. Hence the
detection of ELM module is done through devicetree population of elm_id.
This patch update device tree documentation for gpmc-nand for elm-id
data population.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds device tree bindings for OMAP OneNAND devices.
Tested on an OMAP3 3430 IGEPv2 board.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the FSMC NAND driver and flash partitions to the Nomadik
device tree.
The only compatible string accepted by this driver is currently
"st,spear600-fsmc-nand" which is inappropriate for this system, so
this patch adds the compatible value "stericsson,fsmc-nand" as
well.
Cc: linux-mtd@vger.kernel.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds basic DT bindings for OMAP GPMC.
The actual peripherals are instantiated from child nodes within the GPMC
node, and the only type of device that is currently supported is NAND.
Code was added to parse the generic GPMC timing parameters and some
documentation with examples on how to use them.
Successfully tested on an AM33xx board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
linux,mtd-name allow to specify the mtd name for retro capability with
physmap-flash drivers as boot loader pass the mtd partition via the old
device name physmap-flash.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The flctl can now be probed via device tree setup in addition to the
existing platform data way.
SoC specific setup data is set in the .data member of the OF match, so
kept within the driver itself, while board/user specific setup - like
partitioning - is taken from the device tree.
Actual configuration is added for the SoC sh7372.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Do not use the platform_data to pass resource and be smart in the drivers.
Just pass it via resource
Switch to devm_request_and_ioremap at the sametime
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-By: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add a device tree version of the Denali NAND driver. Based
on an original patch from Jamie Iles to add a MMIO version
of this driver.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause
problems with JFFS2 usage, as the local bus (LPB) doesn't support
unaligned accesses as implemented in the JFFS2 code via memcpy().
By defining "no-unaligned-direct-access", the flash will not be
exposed directly to the MTD users (e.g. JFFS2) any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQLWtvAAoJEHm+PkMAQRiG/DYH+wd0FqfEuYkYk4KPyAPuhKpX
zX7HYfLvyJE/ZYIdrhjq1E6Xm2KNr7gtX7/Rdzi2W38M9sjbYzwG1UGIw51qnxWy
yZJH9BGkfyQgQPeuDGohfB6DkDy2JWr2eqMDvakjOwgBsIzji0PQD/f3UvndhtUa
c+tTj/kjavHE1Yr2Wy6OnRZz3Uc0hIMn/Q0JqtbCs3LUgEV1KA4OEAe56XNz4Ku4
WE+FFaGFPvtriQsQON+ohPS5IC8jzQGK/0vbrJ4lWjFnZy4gvZXnborTOwD0WSQG
fbsNuxp1AaM2/pqfMwXm1w0ADvwOITHNiwwXf9id6DoK81QwTFpUdvKpn6yB6gQ=
=rurr
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux
Having missed the merge window, update to 3.6-rc2 to avoid conflicts with
new patches.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch contains a hack to get the DMA resources of the device when
probed from a devicetree node. This can be removed once a generic DMA
controller framework lands.
A mtd_part_parser_data is passed mtd_device_parse_register which
contains a reference to the device node, so MTD partitions can be
added as children.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
add the on flash bbt support for gpmi nand driver.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a driver for the MLC NAND controller of the LPC32xx SoC.
[dwmw2: 21st century pedantry]
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for the SLC NAND controller inside the LPC32xx SoC.
[dwmw2: 21st century pedantry]
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
Allow a NAND chip using the orion_nand driver to be described using devicetree.
Changes since last submission (V4) [Addressing comments by]:-
* WARN when bank-width is out of range [Andrew Lunn]
Changes since last submission (V3):-
* Document all parameters [Grant Likely]
* Convert bank-width to be in bytes
* Add explicit defaults for cle, ale and bank-width
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch just adds the DT support to gpmi-nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is tested on i.MX27.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add comments to NAND "gpios" property to make it clearer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
Partitions are described in the same way for all mtd devices when using
devicetree, move the documentation to a separate file and add references
to it.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support to configure the SPEAr SMI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support to configure the FSMC NAND driver (used amongst
others on SPEAr platforms) via device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use a local copy of board informatin and fill with DT data.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
- nand-ecc-mode : String, operation mode of the NAND ecc mode.
Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
"soft_bch".
- nand-bus-width : 8 or 16 bus width if not present 8
- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stefan Roese <sr@denx.de>
Add device tree bindings so that the gpio-nand driver may be
instantiated from the device tree. This also allows the partitions
to be specified in the device tree.
v7: - restore runtime device tree/non device tree detection
v6: - convert to mtd_device_parse_register()
v5: - fold dt config helpers into a single gpio_nand_of_get_config()
v4: - get io sync address from gpio-control-nand,io-sync-reg
property rather than a resource
- clarified a few details in the binding
v3: - remove redundant cast and a couple of whitespace/naming
changes
v2: - add CONFIG_OF guards for non-dt platforms
- compatible becomes gpio-control-nand
- clarify some binding details
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It adds device tree probe support for mtd_dataflash driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
For testing the dt work, define a dt-enabled versatile platform.
This patch adds a new versatile platform for when using the device
tree. Add platform and amba devices are discovered and registered by
parsing the device tree. Clocks and initial io mappings are still
configured statically.
This patch still depends on some static platform_data for a few devices
which is passed via the auxdata structure to of_platform_populate(),
but it is a viable starting point until the drivers can get all
configuration data out of the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device tree is used by more than just PowerPC. Make the documentation
directory available to all.
v2: reorganized files while moving to create arch and driver specific
directories.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
