In case of dual DSI, some registers in PHY1 have been programmed
during PLL0 clock's set_rate. The PHY1 reset called by host1 later
will silently reset those PHY1 registers. This change is to reset
and enable both PHYs before any PLL clock operation.
[Originally worked on by Hai Li <hali@codeaurora.org>. Fixed up
by Archit Taneja <architt@codeaurora.org>]
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For some new types of DSI PHY, more settings depend on
use cases controlled by DSI manager. This change allows
DSI manager to setup PHY with a use case.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI host is required to configure more timings calculated
in PHY. By introducing a shared structure, this change allows
more timing information passed from PHY to host.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create an init() op for dsi_phy which sets up things specific to
a given DSI PHY.
The dsi_phy driver probe expects every DSI version to get a
"dsi_phy_regulator" mmio base. This isn't the case for 8x96.
Creating an init() op will allow us to accommodate such
differences.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add 8x96 DSI data in dsi_cfg. The downstream kernel's dsi_host driver
enables core_mmss_clk. We're seeing some branch clock warnings on
8x96 when enabling this. There doesn't seem to be any negative effect
with not enabling this clock, so use it once we figure out why we
get the warnings.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The driver returns an error if a DSI DT node is populated, but no device
is connected to it or if the data-lane map isn't present. Ideally, such
a DSI node shouldn't be probed at all (i.e, its status should be set to
"disabled in DT"), but there isn't any harm in registering the DSI device
even if it doesn't have a bridge/panel connected to it.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This code has been more or less picked up from the vc4 and intel
implementations of update_plane() funcs for cursor planes.
The update_plane() func is usually the drm_atomic_helper_update_plane
func that will issue an atomic commit with the plane updates. Such
commits are not intended to be done faster than the vsync rate.
The legacy cursor userspace API, on the other hand, expects the kernel
to handle cursor updates immediately.
Create a fast path in update_plane, which updates the cursor registers
and flushes the configuration. The fast path is taken when there is only
a change in the cursor's position in the crtc, or a change in the
cursor's crop co-ordinates. For anything else, we go via the slow path.
We take the slow path even when the fb changes, and when there is
currently no fb tied to the plane. This should hopefully ensure that we
always take a slow path for every new fb. This in turn should ensure that
the fb is pinned/prepared.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In mdp5_plane_atomic_check, we get crtc_state from drm_plane_state.
Later, for cursor planes, we'll populate the update_plane() func that
takes a fast asynchronous path to implement cursor movements. There, we
would need to call a similar atomic_check func to validate the plane
state, but crtc_state would need to be derived differently.
Refactor mdp5_plane_atomic_check to mdp5_plane_atomic_check_with_state
such that the latter takes crtc_state as an argument.
This is similar to what the intel driver has done for async cursor
updates.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Register cursor drm_planes. The loop in modeset_init that inits the
planes and crtcs has to be refactored a bit. We first iterate all the
hwpipes to find the cursor planes. Then, we loop again to create
crtcs.
In msm_atomic_wait_for_commit_done, remove the check which bypasses
waiting for vsyncs if state->legacy_cursor_updates is true.
We will later create a fast path for cursor position changes in the
cursor plane's update_plane func that doesn't go via the regular
atomic commit path. For rest of cursor related updates, we will have
to wait for vsyncs, so ignore the legacy_cursor_updates flag.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
These are various changes added in preparation for cursor planes:
- Add a pipe_cursor block for 8x96 in mdp5_cfg.
- Add a new pipe CAP called MDP_PIPE_CAP_CURSOR. Use this to ensure we
assign a cursor SSPP for a drm_plane with type DRM_PLANE_TYPE_CURSOR.
- Update mdp5_ctl_blend_mask/ext_blend_mask funcs to incorporate cursor
SSPPs.
- In mdp5_ctl_blend, iterate through MAX_STAGES instead of stage_cnt,
we need to do this because we can now have empty stages in between.
- In mdp5_crtc_atomic_check, make sure that the cursor plane has the
highest zorder, and stage the cursor plane to the maximum stage #
present on the HW.
- Create drm_crtc_funcs that doesn't try to implement cursors using the
older LM cursor HW.
- Pass drm_plane_type in mdp5_plane_init instead of a bool telling
whether plane is primary or not.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In MDP5 Layer Mixer HW, the blender output is only the blended color
components (i.e R, G and B, or COLOR0/1/2 in MDP5 HW terminology). This
is fed to the BG input of the next blender. We also need to provide an
alpha (COLOR3) value for the BG input at the next stage.
This is configured via using the REG_MDP5_LM_BLEND_COLOR_OUT register.
For each stage, we can propagate either the BG or FG alpha to the next
stage.
The approach taken by the driver is to propagate FG alpha, if the plane
staged on that blender has an alpha. If it doesn't, we try to propagate
the base layer's alpha.
This is borrowed from downstream MDP5 kernel driver. Without this, we
don't see any cursor plane content.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The MDP5 plane's atomic_check ops doesn't perform clipping tests.
This didn't hurt us much in the past, but clipping becomes important
with cursor planes.
Use drm_plane_helper_check_state, the way rockchip/intel/mtk drivers
already do. Use these drivers as reference.
Clipping requires knowledge of the crtc width and height. This requires
us to call drm_atomic_helper_check_modeset before
drm_atomic_helper_check_planes in the driver's atomic_check op, because
check_modetest will populate the mode for the crtc, needed to populate
the clip rectangle.
We update the plane_enabled(state) local helper to use state->visible,
since state->visible and 'state->fb && state->crtc' represent the same
thing.
One issue with the existing code is that we don't have a way to disable
the plane when it's completely clipped out. Until there isn't an update
on the crtc (which would de-stage the plane), we would still see the
plane in its last 'visible' configuration.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use SSPP_NONE in mdp5_plane_pipe() if there is now hwpipe allocated for
the drm_plane. Returning '0' means we are returning VIG0 pipe.
Also, use the mdp5_pipe enum to pass around the stage array. Initialize
the stage to SSPP_NONE by default.
We do the above because 1) Cursor plane has to be staged at the topmost
blender of the LM, which can result in empty stages in between 2) In
the future, when we support multiple LMs per CRTC. We could have stages
which don't have any pipe assigned to them.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently create CRTCs equaling to the # of Layer Mixer blocks we
have on the MDP5 HW. This number is generally more than the # of encoders
(INTFs) we have in the MDSS HW. The number of encoders connected to
displays on the platform (as described by DT) would be even lesser.
Create only N drm_crtcs, where N is the number of drm_encoders
successfully registered. To do this, we call modeset_init_intf() before
we init the drm_crtcs and drm_planes.
Because of this change, setting encoder->possible_crtcs needs to be moved
from construct_encoder() to a later point when we know how many CRTCs we
have.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Count can't be non-zero. Changing to uint will also prevent future
warnings.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For the DSI interfaces, the mdp5_kms core creates 2 encoders for video
and command modes.
Create only a single encoder per interface. When creating the encoder, set
the interface type to MDP5_INTF_MODE_NONE. It's the bridge (DSI/HDMI/eDP)
driver's responsibility to set a different interface type. It can use the
the kms func op set_encoder_mode to change the mode of operation, which
in turn would configure the interface type for the INTF.
In mdp5_cmd_encoder.c, we remove the redundant code, and make the commmand
mode funcs as helpers that are used in mdp5_encoder.c
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Rename the mdp5_encoder_* ops for active displays to
mdp5_vid_encoder_* ops.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp5 kms driver currently sets up multiple encoders per interface
(INTF), one for each kind of mode of operation it supports.
We create 2 drm_encoders for DSI, one for Video Mode and the other
for Command Mode operation. The reason behind this approach could have
been that we aren't aware of the DSI device's mode of operation when
we create the encoders.
This makes things a bit complicated, since these encoders have to
be further attached to the same DSI bridge. The easier way out is
to create a single encoder, and make the DSI driver set its mode
of operation when we know what the DSI device's mode flags are.
Start with providing a way to set the mdp5_intf_mode using a kms
func that sets the encoder's mode of operation. When constructing
a DSI encoder, we set the mode of operation to Video Mode as
default. When the DSI device is attached to the host, we probe the
DSI mode flags and set the corresponding mode of operation.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently create 2 encoders for DSI interfaces, one for command
mode and other for video mode operation. This isn't needed as we
can't really use both the encoders at the same time. It also makes
connecting bridges harder.
Switch to creating a single encoder. For now, we assume that the
encoder is configured only in video mode. Later, the same encoder
would be usable in both modes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The commit "drm: bridge: Link encoder and bridge in core code" updated
the drm_bridge_attach() API to also include the drm_encoder pointer
the bridge attaches to.
The func msm_dsi_manager_bridge_init() now relies on the drm_encoder
pointer stored in msm_dsi->encoders to pass the encoder to the bridge
API.
msm_dsi->encoders is unfortunately set after this function is called,
resulting in us passing a NULL pointer to drm_brigde_attach. This
results in an error and the DSI driver probe fails.
Move the initialization of msm_dsi->encoders[] a bit up. Also, don't
try to set the encoder's bridge. That's now managed by the bridge
API.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Define the block in advance so that the generated mdp5.xml.h doesn't
break build.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Suggested by Rob Herring. We still support the old names for
compatibility with downstream android dt files.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
This was never documented or used in upstream dtb. It is used by
downstream bindings from android device kernels. But the quirks are
a property of the gpu revision, and as such are redundant to be listed
separately in dt. Instead, move the quirks to the device table.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The original way we determined the gpu version was based on downstream
bindings from android kernel. A cleaner way is to get the version from
the compatible string.
Note that no upstream dtb uses these bindings. But the code still
supports falling back to the legacy bindings (with a warning), so that
we are still compatible with the gpu dt node from android device
kernels.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
The plan is to use the OPP bindings. For now, remove the documentation
for qcom,gpu-pwrlevels, and make the driver fall back to a safe low
clock if the node is not present.
Note that no upstream dtb use this node. For now we keep compatibility
with this node to avoid breaking compatibility with downstream android
dt files.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
execlist_update_context() will try to update PDPs in a context before a
ELSP submission only for full PPGTT mode, while PDPs was populated during
context initialization. Now the latter code path is removed. Let
execlist_update_context() also cover !FULL_PPGTT mode.
Fixes: 34869776c7 ("drm/i915: check ppgtt validity when init reg state")
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486377436-15380-1-git-send-email-zhi.a.wang@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
To be consistent with the recent change to enable hotplug detection
early on GEN9 platforms do the same on all non-GMCH platforms starting
from GEN5. On GMCH platforms enabling detection without interrupts isn't
trivial, since AUX and HPD have a shared interrupt line. It could be
done there too by using a SW interrupt mask, but I punt on that for now.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485509961-9010-5-git-send-email-imre.deak@intel.com
This effectively reverts
commit 489375c866
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Oct 24 19:33:31 2016 +0300
drm/i915/lspcon: Add workaround for resuming in PCON mode
The workaround was added without considering that HPD is low during
the failed AUX transfers the WA fixed. Since the previous patch we
wait for HPD to get asserted. My tests also show that this happens
_after_ the DPCD reads start to return correct values. This
suggests that we don't need this WA any more, let's try to remove
it to reduce the clutter.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485509961-9010-4-git-send-email-imre.deak@intel.com
During system resume time initialization the HPD level on LSPCON ports
can stay low for an extended amount of time, leading to failed AUX
transfers and LSPCON initialization. Fix this by waiting for HPD to get
asserted.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99178
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485509961-9010-3-git-send-email-imre.deak@intel.com
For LSPCON resume time initialization we need to sample the
corresponding pin's HPD level, but this is only available when HPD
detection is enabled. Currently we enable detection only when enabling
HPD interrupts which is too late, so bring the enabling of detection
earlier.
This is needed by the next patch.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485509961-9010-2-git-send-email-imre.deak@intel.com
As we now mark the reserved hole (drm_mm.head_node) with the special
UNEVICTABLE color, we can use the page coloring to avoid prefetching of
the CS beyond the end of the GTT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170206084547.27921-3-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
The drm_mm range manager (within i915_address_space) uses a special
drm_mm_node that excludes the unavailable range (beyond the end of the
drm_mm). However, we play games with the global GTT to use the head_node
to exclude the tail page but tell ourselves that the whole range is
available. This causes an issue when we try to evict using the full
range of the global GTT which is wider than the drm_mm, resulting in
complete confusion and catastrophe. One way to resolve this would be to
use a reserved node to exclude the guard page, or we can treat the
drm_mm's head_node as our guard page and assign it the appropriate
colour.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170206084547.27921-2-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
I incorrectly converted the exclusion of the last 4096 bytes (that avoids
any potential prefetching past the end of the GTT) to PAGE_SIZE and not
to I915_GTT_PAGE_SIZE as it should be.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170206084547.27921-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
If we have any residual freed atomic state from earlier commits, flush
the freed list after performing the current modeset. This prevents the
freed list from ever-growing if userspace manages to starve the kernel
threads (i.e. we are never able to run our free state worker and
eventually the system may even oom).
Fixes: eb955eee27 ("drm/i915: Move atomic state free from out of fence release")
Testcase: igt/kms_cursor/legacy/all-pipes-single-bo
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202204741.18231-1-chris@chris-wilson.co.uk
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The only difference for the more recent of those macros is the version
of the *_reg_<read/write>_fw_domains function. Passing the function
prefix in allows us to re-use the same macro to generate functions for
different GENs and will make it easier to add new accessors in the future
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486171409-21542-1-git-send-email-daniele.ceraolospurio@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With atomic modesetting the hardware will be powered off when the
mode_set function is called. We should configure the hardware in the
enable function.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Sometimes the Dock is disconnected, but cdn_dp_encoder_disable is not
triggered by DRM. For example, unplug the Dock in console mode, and
re-plug it again, the cdn_dp_event_work will try to get the sink count
of Dock, since the DP is still active. But the Dock has been powered
down, it need re-power on, and wait for a while until it is ready to
DPCD communication.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
We're trying to lock mutex when cdn-dp shutdown, so we need to make
sure the mutex is inited in cdn-dp's probe.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
The cdn_dp_pd_event_work is using drm_helper_hpd_irq_event to update the
connector status, this function is used to update all connectors of
drm_device. Therefore, the detect of other connector will be call, when
cdn_dp_pd_event_work is triggered, every time. It is not necessary, and
it may cause system crash. replace drm_helper_hpd_irq_event with
drm_kms_helper_hotplug_event, only update cdn-dp status.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
If the driver is in suspended mode, the dp block may be disabled, and
chip registers may not be accessible. Yet, the worker may be triggered
in this situation by an extcon event. If that happens, the following crash
will be seen.
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] *ERROR* Enable dp failed -19
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Connected, not enabled. Enabling cdn
Bad mode in Error handler detected, code 0xbf000002 -- SError
CPU: 1 PID: 10357 Comm: kworker/1:2 Not tainted 4.4.21-05903-ge0514ea #1
Hardware name: Google Kevin (DT)
Workqueue: events cdn_dp_pd_event_work
task: ffffffc0cda67080 ti: ffffffc0b9b80000 task.ti: ffffffc0b9b80000
PC is at cdn_dp_clock_reset+0x30/0xa8
LR is at cdn_dp_enable+0x1e0/0x69c
...
Call trace:
[<ffffffc0005a7e24>] cdn_dp_pd_event_work+0x58/0x3f4
[<ffffffc0002397f0>] process_one_work+0x240/0x424
[<ffffffc00023a28c>] worker_thread+0x2fc/0x424
[<ffffffc00023f5fc>] kthread+0x10c/0x114
[<ffffffc000203dd0>] ret_from_fork+0x10/0x40
Problem is two-fold: The worker should not run while suspended, and the
suspend function should not call cdn_dp_disable() while the worker is
running.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
If no monitor is connected, suspend/resume cycles result in firmware
load errors because the driver attempts to load the firmware while
the system is in suspend state. This results in a kernel warning and
traceback.
Loading the firmware during boot fixes the problem. Note that we can not
just call schedule_work conditionally in cdn_dp_pd_event() if the insertion
status changed. The problem would still be seen if a monitor is connected
for the first time during suspend.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Add support for cdn DP controller which is embedded in the rk3399
SoCs. The DP is compliant with DisplayPort Specification,
Version 1.3, This IP is compatible with the rockchip type-c PHY IP.
There is a uCPU in DP controller, it need a firmware to work,
please put the firmware file to /lib/firmware/rockchip/dptx.bin. The
uCPU in charge of aux communication and link training, the host use
mailbox to communicate with the ucpu.
The dclk pin_pol of vop must not be invert for DP.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
[seanpaul fixed up some races between the worker and modeset]
[seanpaul squashed ~15 commits from chromium.org gerrit]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[groeck fixed compilation errors when building as module]
Signed-off-by: Guenter Roeck <groeck@chromium.org>
rockchip_drm_framebuffer_init is only used in one case, in
rockchip_drm_fbdev.c, where its return value is tested using IS_ERR. To
enable propagating the reason for the error, change the definition so that
it returns an ERR_PTR value.
Problem found with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
The setting of vop registers need a reg_done writing to take effect.
In vop_enable the vop return to work by by restoring registers, but the
registers do not take effect immediately, it should a vop_cfg_done
after it. The same thing is needed by windows_disabled in
vop_crtc_disable.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Fences are creted/checked before the pm ref is taken, so if we jump to
pre_mutex_err we will uncorrectly call intel_runtime_pm_put.
v2: Massage unwind error paths
Fixes: fec0445caa (drm/i915: Support explicit fencing for execbuf)
Testcase: igt/gem_exec_params
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486161930-11764-1-git-send-email-daniele.ceraolospurio@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
