My static checker complains that we are using "autoneg" without
initializing it. The problem is the ->phy_read() condition is reversed
so we only set this on error instead of success.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complained that "v" can be used unintialized if
netxen_rom_fast_read() returns -EIO. That function never actually
returns -1.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cxgb4 is enabled with CONFIG_CHELSIO_T4_DCB set, VI enable command
gets called with DCB enabled. But when we have a back to back setup with
DCB enabled on one side and non-DCB on the Peer side. Firmware doesn't
send any DCB_L2_CFG, and DCB priority is never set for Tx queue.
But driver resets the queue priority and state machine whenever there
is a link down, this patch fixes it by adding a check to reset only if
cxgb4_dcb_enabled() returns true.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we fail to set the flooding configuration for the broadcast and
unregistered multicast traffic, we should revert the flooding
configuration of the unknown unicast traffic.
Fixes: 0293038e0c ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the leave procedure in the error path symmetric to the join
procedure and first remove the port from the collector before
potentially destroying the LAG.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP tunnel segmentation code relies on the inner offsets being set for
an UDP tunnel GSO packet, but the inner *_complete() functions will
set the inner offsets only if 'encapsulation' is set before calling
them. Currently, udp_gro_complete() sets 'encapsulation' only after
the inner *_complete() functions are done. This causes the inner
offsets having invalid values after udp_gro_complete() returns, which
in turn will make it impossible to properly segment the packet in case
it needs to be forwarded, which would be visible to the user either as
invalid packets being sent or as packet loss.
This patch fixes this by setting skb's 'encapsulation' in
udp_gro_complete() before calling into the inner complete functions,
and by making each possible UDP tunnel gro_complete() callback set the
inner_mac_header to the beginning of the tunnel payload.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Reviewed-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setting of the UDP tunnel GSO type is already performed by
udp[46]_gro_complete().
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating macvtaps that are expected to have the same ifindex
in different network namespaces, only the first one will succeed.
The others will fail with a sysfs_warn_dup warning due to them trying
to create the following sysfs link (with 'NN' the ifindex of macvtapX):
/sys/class/macvtap/tapNN -> /sys/devices/virtual/net/macvtapX/tapNN
This is reproducible by running the following commands:
ip netns add ns1
ip netns add ns2
ip link add veth0 type veth peer name veth1
ip link set veth0 netns ns1
ip link set veth1 netns ns2
ip netns exec ns1 ip l add link veth0 macvtap0 type macvtap
ip netns exec ns2 ip l add link veth1 macvtap1 type macvtap
The last command will fail with "RTNETLINK answers: File exists" (along
with the kernel warning) but retrying it will work because the ifindex
was incremented.
The 'net' device class is isolated between network namespaces so each
one has its own hierarchy of net devices.
This isn't the case for the 'macvtap' device class.
The problem occurs half-way through the netdev registration, when
`macvtap_device_event` is called-back to create the 'tapNN' macvtap
class device under the 'macvtapX' net class device.
This patch adds namespace support to the 'macvtap' device class so
that /sys/class/macvtap is no longer shared between net namespaces.
However, making the macvtap sysfs class namespace-aware has the side
effect of changing /sys/devices/virtual/net/macvtapX/tapNN into
/sys/devices/virtual/net/macvtapX/macvtap/tapNN.
This is due to Commit 24b1442 ("Driver-core: Always create class
directories for classses that support namespaces") and the fact that
class devices supporting namespaces are really not supposed to be placed
directly under other class devices.
To avoid breaking userland, a tapNN symlink pointing to macvtap/tapNN is
created inside the macvtapX directory.
Signed-off-by: Marc Angel <marc@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-05-05
This series contains updates to i40e and i40evf.
The theme behind this series is code reduction, yeah! Jesse provides
most of the changes starting with a refactor of the interpretation of
a tunnel which lets us start using the hardware's parsing. Removed
the packet split receive routine and ancillary code in preparation
for the Rx-refactor. The refactor of the receive routine,
aligns the receive routine with the one in ixgbe which was highly
optimized. The hardware supports a 16 byte descriptor for receive,
but the driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole lot
of complexity while getting rid of the code. Fixed a bug where while
changing the number of descriptors using ethtool, the driver did not
test the limits of the system memory before permanently assuming it
would be able to get receive buffer memory.
Mitch fixes a memory leak of one page each time the driver is opened by
allocating the correct number of receive buffers and do not fiddle with
next_to_use in the VF driver.
Arnd Bergmann fixed a indentation issue by adding the appropriate
curly braces in i40e_vc_config_promiscuous_mode_msg().
Julia Lawall fixed an issue found by Coccinelle, where i40e_client_ops
structure can be const since it is never modified.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tables have to exist for VRFs to function. Ensure they exist
when VRF device is created.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qede requires qed to provide enough resources to accommodate 16 combined
channels, but that upper-bound isn't actually being enforced by it.
Instead, qed inform back to qede how many channels can be opened based on
available resources - but that calculation doesn't really take into account
the resources requested by qede; Instead it considers other FW/HW available
resources.
As a result, if a user would increase the number of channels to more than
16 [e.g., using ethtool] the chip would hang.
This change increments the resources requested by qede to 64 combined
channels instead of 16; This value is an upper bound on the possible
available channels [due to other FW/HW resources].
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently had a system crash in the cnic module. Vmcore analysis confirmed
that "ip link up" was executed which failed due to an allocation failure
because of memory fragmentation. Futher analysis revealed that the cnic irq
vector was still allocated after the "ip link up" that failed. When
"ip link down" was executed it called free_msi_irqs() which crashed the system
because the cnic irq was still inuse.
PANIC: "kernel BUG at drivers/pci/msi.c:411!"
The code execution was:
cnic_netdev_event()
if (event == NETDEV_UP) {
.
.
▹ if (!cnic_start_hw(dev))
cnic_start_hw()
calls cnic_cm_open() which failed with -ENOMEM
cnic_start_hw() then took the err1 path:
err1:↩
cp->free_resc(dev);↩ <---- frees resources but not irq vector
pci_dev_put(dev->pcidev);↩
return err;↩
}↩
This returns control back to cnic_netdev_event() but now the cnic irq vector
is still allocated even although cnic_cm_open() failed. The next
"ip link down" while trigger the crash.
The cnic_start_hw() routine is not handling the allocation failure correctly.
Fix this by checking whether CNIC_DRV_STATE_HANDLES_IRQ flag is set indicating
that the hardware has been started in cnic_start_hw(). If it has then call
cp->stop_hw() which frees the cnic irq vector and cnic resources. Otherwise
just maintain the previous behaviour and free cnic resources.
I reproduced this by injecting an ENOMEM error into cnic_cm_alloc_mem()s return
code.
# ip link set dev enpX down
# ip link set dev enpX up <--- hit's allocation failure
# ip link set dev enpX down <--- crashes here
With this patch I confirmed there was no crash in the reproducer.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e_client_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Newly added code in i40e_vc_config_promiscuous_mode_msg() is indented
in a way that gcc rightly complains about:
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c: In function 'i40e_vc_config_promiscuous_mode_msg':
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:1543:4: error: this 'if' clause does not guard... [-Werror=misleading-indentation]
if (f->vlan >= 0 && f->vlan <= I40E_MAX_VLANID)
^~
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:1550:5: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the 'if'
aq_err = pf->hw.aq.asq_last_status;
From the context, it looks like the aq_err assignment was meant to be
inside of the conditional expression, so I'm adding the appropriate
curly braces now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5676a8b9cd ("i40e: Add VF promiscuous mode driver support")
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When testing on systems with very limited amounts of RAM, a bug was
found where, while changing the number of descriptors using ethtool,
the driver didn't test the limits of system memory before permanently
assuming it would be able to get receive buffer memory.
Work around this issue by pre-allocation of the receive buffer
memory, in the "ghost" ring, which is then used during reinit
using the new ring length.
Change-Id: I92d7a5fb59a6c884b2efdd1ec652845f101c3359
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allocate the correct number of RX buffers, and don't fiddle with
next_to_use. The common RX code handles all of this. This fixes a memory
leak of one page each time the driver is opened.
Change-Id: Id06eca353086e084921f047acad28c14745684ee
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a 16 byte descriptor for receive, but the
driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole
lot of complexity while getting rid of the code.
Also since the previous patch made us use no-split mode all the
time, drop any support in the driver for any other value in dtype
and assume it is always zero (aka no-split).
Hooray for code removal!
Change-ID: I2257e902e4dad84a07b94db6d2e6f4ce69b27bc0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is part 2 of the Rx refactor series, just including
changes to i40evf.
This refactor aligns the receive routine with the one in
ixgbe which was highly optimized. This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.
In order to do this:
- consolidate the receive path into a single function that doesn't
use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove VF ethtool control over packet split
- remove priv_flags interface since it is unused
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Some of the split related context set up code stays in
i40e_virtchnl_pf.c in case an older VF driver tries to load
and still wants to use packet split.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is part 1 of the Rx refactor series, just including
changes to i40e.
This refactor aligns the receive routine with the one in
ixgbe which was highly optimized. This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.
In order to do this:
- consolidate the receive path into a single function that doesn't
use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove ethtool control over packet split
Change-ID: I5ca100721de65992aa0114f8b4bac844b84758e0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use htons instead of unconditionally byte swapping nexthdr. On a little
endian systems shifting the byte is correct behavior, but it results in
incorrect csums on big endian architectures.
Fixes: f8c6455bb0 ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Carol Soto <clsoto@us.ibm.com>
Tested-by: Carol Soto <clsoto@us.ibm.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma_alloc_coherent() function returns a virtual address which can
be used for coherent access to the underlying memory. On some
architectures, like arm64, undefined behavior results if this memory is
also accessed via virtual mappings that are not coherent. Because of
their undefined nature, operations like virt_to_page() return garbage
when passed virtual addresses obtained from dma_alloc_coherent(). Any
subsequent mappings via vmap() of the garbage page values are unusable
and result in bad things like bus errors (synchronous aborts in ARM64
speak).
The mlx4 driver contains code that does the equivalent of:
vmap(virt_to_page(dma_alloc_coherent)), this results in an OOPs when the
device is opened.
Prevent Ethernet driver to run this problematic code by forcing it to
allocate contiguous memory. As for the Infiniband driver, at first we
are trying to allocate contiguous memory, but in case of failure roll
back to work with fragmented memory.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reported-by: David Daney <david.daney@cavium.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the rx-refactor, the dtype variable in the i40e_ring
struct is no longer used, so remove it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the interpretation of a tunnel. This removes
some code and lets us start using the hardware's parsing.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-05-04
This series contains updates to ixgbe, ixgbevf and traffic class helpers.
Sridhar adds helper functions to the tc_mirred header to access tcf_mirred
information and then implements them for ixgbe to enable redirection to
a SRIOV VF or an offloaded MACVLAN device queue via tc 'mirred' action.
Amritha adds support to set filters with multiple header fields (L3,L4)
to match on.
KY Srinivasan from Microsoft add Hyper-V support into ixgbevf.
Emil adds 82599 sub-device IDs that were missing from the list of parts
that support WoL. Then simplified the logic we use to determine WoL
support by reading the EEPROM bits for MACs X540 and newer.
Preethi cleaned up duplicate and unused device IDs. Fixed our ethtool
stat reporting where we were ignoring higher 32 bits of stats registers,
so fill out 64 bit stat values into two 32 bit words.
Babu Moger from Oracle improves VF performance issues on SPARC.
Alex Duyck cleans up some of the Hyper-V implementation from KY so that
we can just use function pointers instead of having to identify if a
given VF is running on a Linux or Windows PF.
Usha makes sure that DCB and FCoE is disabled for X550EM_x/a MACs and
cleans up the DCB initialization in the process.
Tony cleans up the API for ixgbevf_update_xcast_mode() so we do not
have to pass in the netdev parameter, since it was never used in the
function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The multicast/all-multicast internal flags are not properly restored
after device reset. This could lead to unreliable multicast operations
after an ethtool configuration change for example.
Call bnxt_mc_list_updated() and setup the vnic->mask in bnxt_init_chip()
to fix the issue.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code determines if the next ring entry is valid before proceeding
further to read the rest of the entry. The CPU can re-order and read
the rest of the entry first, possibly reading a stale entry, if DMA
of a new entry happens right after reading it. This issue can be
readily seen on a ppc64 system, causing it to crash.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot reported a build failure on s390.
While at it, also fix missing conversion in the tilera driver.
Fixes: 9b36627ace ("net: remove dev->trans_start")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the call to fn() fails then "buf" is uninitialized. Just return the
error code in that case.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the fn() calls fail then "buf" is uninitialized. Just return early
in that situation.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've finally noticed that mdiobus_scan() also returns either NULL or error
value on failure. Return ERR_PTR(-ENODEV) instead of NULL since this is
the error value already filtered out by the callers that want to ignore
the MDIO address scan failure...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
previous patches removed all direct accesses to dev->trans_start,
so change the netif_trans_update helper to update trans_start of
netdev queue 0 instead and then remove trans_start from struct net_device.
AFAICS a lot of the netif_trans_update() invocations are now useless
because they occur in ndo_start_xmit and driver doesn't set LLTX
(i.e. stack already took care of the update).
As I can't test any of them it seems better to just leave them alone.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
a trans_start struct member exists twice:
- in struct net_device (legacy)
- in struct netdev_queue
Instead of open-coding dev->trans_start usage to obtain the current
trans_start value, use dev_trans_start() instead.
This is not exactly the same, as dev_trans_start also considers
the trans_start values of the netdev queues owned by the device
and provides the most recent one.
For legacy devices this doesn't matter as dev_trans_start can cope
with netdev trans_start values of 0 (they are ignored).
This is a prerequisite to eventual removal of dev->trans_start.
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
use net_device directly. Compile tested, objdiff shows no changes.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the receive path a queue's work bit was cleared unconditionally even
if fec_enet_rx_queue only read out a part of the available packets from
the hardware. This resulted in not reading any packets in the next napi
turn and so packets were delayed or lost.
The obvious fix is to only clear a queue's bit when the queue was
emptied.
Fixes: 4d494cdc92 ("net: fec: change data structure to support multiqueue")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add support to configure trusted vf attribute through trust_vf_ndo.
- Upon VF trust setting change we update vport context to refresh
allmulti/promisc or any trusted vf attributes that we didn't trust the
VF for before.
- Lock the eswitch state lock on vport event in order to synchronise the
vport context updates , this will prevent contention with vport trust
setting change which will trigger vport mac list update.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add promisc_change as a trigger to vport context change event.
Add set vport promisc/allmulti functions to add vport to promiscuous
flowtable rules.
Upon promisc/allmulti rx mode vf request add the vport to
the relevant promiscuous group (Allmulti/Promisc group) so the relevant
traffic will be forwarded to it.
Upon allmulti vf request add the vport to each existing multicast fdb
rule.
Upon adding/removing mcast address from a vport, update all other
allmulti vports.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add promiscuous and allmulti steering groups in FDB table.
Besides the full match L2 steering rules group, we added
two more groups to catch the "miss" rules traffic:
* Allmulti group: One rule that forwards any mcast traffic coming from
either uplink or VFs/PF vports
* Promisc group: One rule that forwards all unmatched traffic coming
from uplink.
Needed for downstream privileged VF promisc and allmulti support.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the usage of explicit cleanup function and use existing vport
change handler. Calling vport change handler while vport
is disabled will cleanup the vport resources.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable ingress/egress ACL tables only when we need to configure ACL
rules.
Disable ingress/egress ACL tables once all ACL rules are removed.
All VF outgoing/incoming traffic need to go through the ingress/egress ACL
tables.
Adding/Removing these tables on demand will save unnecessary hops in the
flow steering when the ACL tables are empty.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure ingress and egress vport ACL rules according to spoofchk
admin parameters.
Ingress ACL flow table rules:
if (!spoofchk && !vst) allow all traffic.
else :
1) one of the following rules :
* if (spoofchk && vst) allow only untagged traffic with smac=original
mac sent from the VF.
* if (spoofchk && !vst) allow only traffic with smac=original mac sent
from the VF.
* if (!spoofchk && vst) allow only untagged traffic.
2) drop all traffic that didn't hit #1.
Add support for set vf spoofchk ndo.
Add non zero mac validation in case of spoofchk to set mac ndo:
when setting new mac we need to validate that the new mac is
not zero while the spoofchk is on because it is illegal
combination.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure ingress and egress vport ACL rules according to
vlan and qos admin parameters.
Ingress ACL flow table rules:
1) drop any tagged packet sent from the VF
2) allow other traffic (default behavior)
Egress ACL flow table rules:
1) allow only tagged traffic with vlan_tag=vst_vid.
2) drop other traffic.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create egress/ingress ACLs per VF vport at vport enable.
Ingress ACL:
- one flow group to drop all tagged traffic in VST mode.
Egress ACL:
- one flow group that allows only untagged traffic with
smac that is equals to the original mac (anti-spoofing).
- one flow group that allows only untagged traffic.
- one flow group that allows only smac that is equals
to the original mac (anti-spoofing).
(note: only one of the above group has active rule)
- star rule will be used to drop all other traffic.
By default no rules are generated, unless VST is explicitly requested.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vport spin lock can be replaced with synchronize_irq() in the right
place, this will remove the need of locking inside irq context.
Locking in esw_enable_vport is not required since vport events are yet
to be enabled, and at esw_disable_vport it is sufficient to
synchronize_irq() to guarantee no further vport events handlers will be
scheduled.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the relevant flow steering device structs and commands to
support vport.
Update the flow steering core API to receive vport number.
Add ingress and egress ACL flow table name spaces.
Add ACL flow table support:
* ACL (Access Control List) flow table is a table that contains
only allow/drop steering rules.
* We have two types of ACL flow tables - ingress and egress.
* ACLs handle traffic sent from/to E-Switch FDB table, Ingress refers to
traffic sent from Vport to E-Switch and Egress refers to traffic sent
from E-Switch to vport.
* Ingress ACL flow table allow/drop rules is checked against traffic
sent from VF.
* Egress ACL flow table allow/drop rules is checked against traffic sent
to VF.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
en_arfs.o should be compiled only if both CONFIG_MLX5_CORE_EN
and CONFIG_RFS_ACCEL are enabled. en_arfs calls to rps_may_expire_flow
which is compiled only if CONFIG_RFS_ACCEL is defined.
Move en_arfs.o compilation dependency to be under CONFIG_MLX5_CORE_EN
and wrap the en_arfs.c content with ifdef of CONFIG_RFS_ACCEL.
Fixes: 1cabe6b096 ('net/mlx5e: Create aRFS flow tables')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probe bails out with an error, we try to unregister the
netdev before we have even registered it. Fix the goto statements
for that.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO code creates A-MSDUs from a single large send. Each
A-MSDU is an skb and skb->len doesn't include the number of
bytes which need to be added for the headers being added
(subframe header, TCP header, IP header, SNAP, padding).
To be able to set the right value in the Tx command, we
put the number of bytes added by those headers in
driver_data in iwl_mvm_tx_tso and use this value in
iwl_mvm_set_tx_cmd.
The problem by setting this value in driver_data is that
it overrides the ieee80211_tx_info. The bug manifested
itself when we send P2P related frames in CCK since the
rate in ieee80211_tx_info is zero-ed. This of course is
a violation of the P2P specification.
To fix this, copy the original ieee80211_tx_info to the
stack and pass it to the functions which need it.
Assign the number of bytes added by the headers to the
driver_data inside the skb itself.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Check for firmware errors in the mailbox command loop and report
them differently rather than simply timing out when the firmware goes
belly up.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link goes down, from the interrupt handler DCB priority for the
Tx queues needs to be unset. We issue mbox command to unset the Tx queue
priority with negative timeout. In t4_wr_mbox_meat_timeout() do not sleep
when negative timeout is passed, since it is called from interrupt context.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the phy initialization code for Qualcomm
Atheros AR8035 phy. This configuration is found in the
Cisco Meraki MR24.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch assumes that the bnxt hardware will ignore existing IPv4/v6
header fields for length and checksum as well as the length and checksum
fields for outer UDP and GRE headers.
I have been told by Michael Chan that this is working. Though this might
be somewhat redundant for IPv6 as they are forcing the checksum to be
computed for all IPv6 frames that are offloaded. A follow-up patch may be
necessary in order to fix this as it is essentially mangling the outer IPv6
headers to add a checksum where none was requested.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5 driver exposes support for TSO6 but not IPv6 csum for hardware
encapsulated tunnels. This leads to issues as it triggers warnings in
skb_checksum_help as it ends up being called as we report supporting the
segmentation but not the checksumming for IPv6 frames.
This patch corrects that and drops 2 features that don't actually need to
be supported in hw_enc_features since they are Rx features and don't
actually impact anything by being present in hw_enc_features.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch assumes that the mlx5 hardware will ignore existing IPv4/v6
header fields for length and checksum as well as the length and checksum
fields for outer UDP headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From what I can tell the ConnectX-3 will support an inner IPv6 checksum and
segmentation offload, however it cannot support outer IPv6 headers. This
assumption is based on the fact that I could see the checksum being
offloaded for inner header on IPv4 tunnels, but not on IPv6 tunnels.
For this reason I am adding the feature to the hw_enc_features and adding
an extra check to the features_check call that will disable GSO and
checksum offload in the case that the encapsulated frame has an outer IP
version of that is not 4. The check in mlx4_en_features_check could be
removed if at some point in the future a fix is found that allows the
hardware to offload segmentation/checksum on tunnels with an outer IPv6
header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch assumes that the mlx4 hardware will ignore existing IPv4/v6
header fields for length and checksum as well as the length and checksum
fields for outer UDP headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbevf_update_xcast_mode() is not using the netdev parameter;
removing it since it's unnecessary.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds IXGBE_FLAG_DCB_CAPABLE flag that is set
for all MACs other than X550EM_x and x550em_a. DCB and
FCoE is disabled for these MACS. DCB initialization
code is moved to a separate function.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Ronald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can just use function pointers instead of
having to identify if a given VF is running on a Linux or Windows PF. By
doing this we can avoid having to pull too much information out of the
lower layers and can instead just make use of the mac_ops pointers since
they should differ between the two types of VFs anyway.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We noticed performance issues with VF interface on sparc compared
to PF. Setting the RX to IXGBE_DCA_RXCTRL_DATA_WRO_EN brings it
on far with PF. Also this matches to the default sparc setting in
PF driver.
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Revise populating few registers in ixgbe_get_regs() and macro
definitions.
Before applying patch:
$ du -k objs/drivers/net/ethernet/intel/ixgbe/ixgbe.ko
8572 objs/drivers/net/ethernet/intel/ixgbe/ixgbe.ko
After applying patch:
$ du -k objs/drivers/net/ethernet/intel/ixgbe/ixgbe.ko
8568 objs/drivers/net/ethernet/intel/ixgbe/ixgbe.ko
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code was ignoring higher 32 bits of stats registers. This patch
correctly fills out 64 bit value in two 32 bit words.
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove duplicate and unused device ID definitions.
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change aims to simplify the logic we use to determine WOL
support by reading the EEPROM bits for MACs X540 and newer.
Also some cleanups in ixgbe_wol_supported() - changed return type to
bool and removed redundant return variable by simply using return after
the checks.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We had some 82599 subdevice IDs missing from the list of parts that
support WoL.
Reported-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On Hyper-V, the VF/PF communication is a via software mediated path
as opposed to the hardware mailbox. Make the necessary
adjustments to support Hyper-V.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Intel SR-IOV cards present different ID when running on Hyper-V.
Add the device IDs presented while running on Hyper-V.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds support to set filters with multiple header fields (L3,L4)to match on.
This is achieved in the following order:
1. Create a leaf hash table for the next header.
2. Create a link to the leaf hash table from the base hash table with
matches on next header type and current header fields.
3. Add filter in leaf hash table with match on next header fields and
action.
Verified with the following filters :
Match TCP and DIP:
handle 1: u32 divisor 1
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 6 ff match ip dst 10.0.0.1/32
match tcp src 28 ffff action drop
Delete the filter:
Match on DIP, SIP, UDP (SPort, DPort):
handle 2: u32 divisor 1
u32 ht 800: order 2 link 2: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip dst 15.0.0.2/32 match ip protocol 17 ff \
match ip src 15.0.0.1/32
match udp src 30 ffff match udp dst 32 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables 'redirect' to a SRIOV VF or a offloaded macvlan
device queue via tc 'mirred' action.
Verified with the following script that creates SRIOV VFs, offloaded
macvlan and adds tc u32 filters with redirect action to the associated
netdevs.
# add ingress qdisc.
tc qdisc add dev p4p1 ingress
# enable hw tc offload.
ethtool -K p4p1 hw-tc-offload on
# create 4 sriov VFs and bring up the first one.
echo 4 > /sys/class/net/p4p1/device/sriov_numvfs
sleep 1
ip link set p4p1 up
ip link set p4p1_0 up
# create a offloaded macvlan device and bring it up.
ethtool -K p4p1 l2-fwd-offload on
ip link add link p4p1 name mvlan_1 type macvlan
ip link set mvlan_1 up
# add u32 filter with action to redirect to VF netdev
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:1 u32 ht 800: \
match ip src 192.168.1.3/32 \
action mirred egress redirect dev p4p1_0
# add u32 filter with action to redirect to macvlan netdev
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:2 u32 ht 800: \
match ip src 192.168.2.3/32 \
action mirred egress redirect dev mvlan_1
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current sequence makes us register for a network device prior to
registering and probing the MDIO bus which could lead to some unwanted
consequences, like a thread of execution calling into ndo_open before
register_netdev() returns, while the MDIO bus is not ready yet.
Rework the sequence to register for the MDIO bus, and therefore attach
to a PHY prior to calling register_netdev(), which implies reworking the
error path a bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure and enable various tunnels on the
adapter after PF start.
This change was missed as a part of
'commit 464f664501
("qed: Add infrastructure support for tunneling")'
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3b9d6da67e ("cpu/hotplug: Fix rollback during error-out
in __cpu_disable()") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this SMP
function calls are no longer required.
Replace smp_call_function_single() with a direct call to
mvneta_percpu_enable() or mvneta_percpu_disable(). The functions do
not require to be called with interrupts disabled, therefore the
smp_call_function_single() calling convention is not preserved.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove old init callback which now contains only a call to
socfpga_dwmac_setup(). Also rename socfpga_dwmac_setup() to indicate
what the function really does.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_resume() should only be need during driver resume to
workaround a hardware errata.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-socfpga driver needs to control the reset usually managed
by the core driver to set the PHY mode. Take a copy of the reset
handle from core priv data so it can be used by the driver later.
This also allow us to move reset handling into socfpga_dwmac_setup()
where the code that needs it is located.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the needed PM callbacks in the driver instead of
relying on the init/exit hooks in stmmac_platform. This gives
the driver more flexibility in how the code is organized.
Eventually the init/exit callbacks will be deprecated in favor
of the standard PM callbacks and driver remove function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change stmmac_remove/resume/suspend to take a device pointer so
they can be used directly by drivers that doesn't need to perform
anything device specific.
This lets us remove the PCI pm functions and later simplifiy the
platform drivers.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now mdiobus_scan() returns ERR_PTR(-ENODEV) instead of NULL if the PHY
device ID was read as all ones. As this was not an error before, this
value should be filtered out now in this driver.
Fixes: b74766a0a0 ("phylib: don't return NULL from get_phy_device()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mdiobus_scan() returns either an error code or NULL on error, the
driver should check for both, not only for NULL, otherwise a crash is
imminent...
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vxlan add/delete port NDOs are called under rcu lock.
The current mlx5e implementation can potentially block in these
calls, which is not allowed. Move to using the mlx5e workqueue
to handle these NDOs.
Fixes: b3f63c3d5e ('net/mlx5e: Add netdev support for VXLAN tunneling')
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a mlx5e workqueue to handle all mlx5e specific tasks. Move
all tasks currently using the system workqueue to the new workqueue.
This is in preparation for vxlan using the mlx5e workqueue in order to
schedule port add/remove operations.
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When MLX5_EN=y MLX5_CORE=y and VXLAN=m there is a linker error for
vxlan_get_rx_port() due to the fact that VXLAN is a module. Change Kconfig
to select VXLAN when MLX5_CORE=y. When MLX5_CORE=m there is no dependency
on the value of VXLAN.
Fixes: b3f63c3d5e ('net/mlx5e: Add netdev support for VXLAN tunneling')
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When freeing UAR the driver tries to unmap uar->map and uar->bf_map
which are mutually exclusive thus always unmapping a NULL pointer.
Make sure we only call iounmap() once, for the actual mapping.
Fixes: 0ba422410b ('net/mlx5: Fix global UAR mapping')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reported-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the fec_mpc52xx driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the fs-enet driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the ucc driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the gianfar driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgene_cle_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aligning the reception data size is not required.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
brcmfmac
* add support for nl80211 BSS_SELECT feature
mwifiex
* add platform specific wakeup interrupt support
ath10k
* implement set_tsf() for 10.2.4 branch
* remove rare MSI range support
* remove deprecated firmware API 1 support
ath9k
* add module parameter to invert LED polarity
wcn36xx
* fixes to get the driver properly working on Dragonboard 410c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXJztPAAoJEG4XJFUm622beSAIAKIw8zGcs7DWd/AGd9z8D7L5
DeO6fxhiu/05AU3d1jM7Rp/Z5hZ42s41PDjRN1lkZJaF4Squa7XOxuB35JlPd+o8
2S21lvaM6ABraSEcDdYL++rglXFL65gIesv/W4TuxqdJCmi9fL7ie7ccplQH17bi
KyY3ePihHZPOR8aXMRbdEzTEjjPFaO/LlAghHPw5WKmVy7FkFKSyFR8muFEPnKEl
DSBWmG6GqRQaHUuVl1QOmoEEqiv7h85D+YqwKiy/xEM4Yw5Rmt5n5pj02KA0i4y5
IRZs59I/8zdAgDgBd+liVeBw9Gp2xAV5R8afOTdzViBDrqCbDCwNq6OPG1GmkLw=
=lyGT
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-05-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
brcmfmac
* add support for nl80211 BSS_SELECT feature
mwifiex
* add platform specific wakeup interrupt support
ath10k
* implement set_tsf() for 10.2.4 branch
* remove rare MSI range support
* remove deprecated firmware API 1 support
ath9k
* add module parameter to invert LED polarity
wcn36xx
* fixes to get the driver properly working on Dragonboard 410c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets ethernet to CPU channel (prefetch buffer number) from
the newly added 'channel' property, thus decoupling Linux driver from
resource management.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the qede implementation for internal loopback test.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the qede ethtool support for the following tests:
- interrupt test
- memory test
- register test
- clock test
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the functionality and APIs needed for selftests.
It adds the ability to configure the link-mode which is required for the
implementation of loopback tests. It adds the APIs for clock test,
register test, interrupt test and memory test.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure ds is actually needed in very few places,
mostly during setup of the switch. The private structure ps is however
needed nearly everywhere. Pass ps, not ds internally.
[vd: rebased Andrew's patch.]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-05-01
This series contains updates to i40e and i40evf.
The theme of this series is code reduction, with several code cleanups in
this series. Starting with Neerav's removal of the code that implemented
the HMC AQ APIs and calls, since they are now obsolete and not supported
by firmware.
Anjali changes the default of VFs to make sure they are not trusted or
privileged until its explicitly set for trust through the new NDO op
interface. Also limited the number of MAC and VLAN addresses a VF can
add if it is untrusted/privileged.
Carolyn syncs the VF code for the changes made to the PF for the RSS
hash tuple settings, which ends up cleaning up much of the existing code.
Jesse cleans up compiler warnings which were found with gcc's W=2 option.
Then removed duplicate code, especially since only one copy was actually
being used.
Jacob addresses an issue which was found when testing GCC 6's which
happens to produce new warnings when you left shift a signed value
beyond the storage sizeof the type. The converts i40e & i40evf to use
the BIT() macro more consistently.
Alex actually bucks the trend of code removal by adding support for
both drivers to use GSO_PARTIAL so that segmentation of frames with
checksums enabled in outer headers is supported. Fortunately it does
not take much to add this support!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An out of bounds read of 2 bytes was discovered in cxgb3 with KASAN.
t3_config_rss() expects both arrays it gets as parameters to have
terminators. setup_rss(), the caller, forgets to add a terminator to
one of the arrays. Thankfully the iteration in t3_config_rss() stops
anyway, but in the last iteration the check for the terminator
is an out of bounds read.
Add the missing terminator to rspq_map[].
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This takes the MAC address for smsc75xx/smsc95xx USB network devices
from a the device tree. This is required to get a usable persistent
address on the popular beagleboard, whose hardware designers
accidentally forgot that an ethernet device really requires an a
MAC address to be functional.
The Raspberry Pi also ships smsc9514 without a serial EEPROM, stores
the MAC address in ROM accessible via VC4 firmware.
The smsc75xx and smsc95xx drivers are just two copies of the
same code, so better fix both.
[lkundrak@v3.sk: updated to use of_get_property() as per suggestion from
Arnd, reworded the message and comments a bit]
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit b74766a0a0 ("phylib: don't return NULL
from get_phy_device()") in linux-next, phy_get_device() will return
ERR_PTR(-ENODEV) instead of NULL if the PHY device ID is all ones.
This causes problem with stmmac driver and likely some other drivers
which call mdiobus_register(). I triggered this bug on SoCFPGA MCVEVK
board with linux-next 20160427 and 20160428. In case of the stmmac, if
there is no PHY node specified in the DT for the stmmac block, the stmmac
driver ( drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c function
stmmac_mdio_register() ) will call mdiobus_register() , which will
register the MDIO bus and probe for the PHY.
The mdiobus_register() resp. __mdiobus_register() iterates over all of
the addresses on the MDIO bus and calls mdiobus_scan() for each of them,
which invokes get_phy_device(). Before the aforementioned patch, the
mdiobus_scan() would return NULL if no PHY was found on a given address
and mdiobus_register() would continue and try the next PHY address. Now,
mdiobus_scan() returns ERR_PTR(-ENODEV), which is caught by the
'if (IS_ERR(phydev))' condition and the loop exits immediately if the
PHY address does not contain PHY.
Repair this by explicitly checking for the ERR_PTR(-ENODEV) and if this
error comes around, continue with the next PHY address.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that i40e and i40evf can use GSO_PARTIAL to support
segmentation for frames with checksums enabled in outer headers. As a
result we can now send data over these types of tunnels at over 20Gb/s
versus the 12Gb/s that was previously possible on my system.
The advantage with the i40e parts is that this offload is mostly
transparent as the hardware still deals with the inner and/or outer IPv4
headers so the IP ID is still incrementing for both when this offload is
performed.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
GCC 6 has a new warning which will display when you attempt to left
shift a signed value beyond the storage size of the type. I40E_MASK
generates a mask value for 32bit registers. Properly typecast the mask
value and place the values in parenthesis to prevent macro expansion
issues.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a device ID for X722.
Change-Id: I574f2345ab341de98a6a1c212d0603af853e48b0
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_release_rx_desc was in two files, but was only used
and needed in txrx.c. Get rid of the extra copy.
Change-Id: I86e18239aa03531fc198b6c052847475084a9200
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was all over the place using signed or unsigned types
for vf_id, when it should always be signed.
This fixes warnings of type unsafe comparisons from gcc with W=2.
Change-Id: I2cb681f83d0f68ca124d2e4131e4ac0d9f8a6b22
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Aggregate return warnings are when struct types are returned
and must be copied to the lvalue with a struct copy by the compiler.
This fixes warnings of type aggregate-return from gcc with W=2.
Change-Id: I896b1bf514544bf0faeb458869d79914b9f1b168
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have an uninitialized variable warning for valid_len for one case in
validate_vf_mesg. To fix this, just initialize it to 0 at the top of the
function and remove all of the now redundant assignments to 0 in the
individual cases.
Change-Id: Iacbd97f4c521ed8d662eef803a598d8707708cfd
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch syncs the VF code for the changes made to the PF for the RSS
hash tuple settings. Since the VF still cannot change the RSS hash
settings, change the code to make this clear to the user. Previously,
the default settings were returned in this function. However, the
default can be changed by the PF so this does not make sense anymore.
Change-Id: I085eaf005fc7978b440d2a1bf2b2dd7cadaff39b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the code that implements the HMC AQ APIs and call these APIs.
This is done because these are obsolete APIs and are not supported
by firmware.
Change-ID: I5d771d8f37c3e16e7b0a972ff9b27e75aa2d05d4
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this change a non trusted VF can never fall to promiscuous
mode when there is no room for a MAC/VLAN filter.
Change-Id: I8a155aa25c0bcdc6093414920c9ade4ee0bd20e8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF is privileged/trusted it can do as it may please including
but not limited to hogging resources and playing unfair.
But if the VF is not privileged/trusted it still can add some number
(8) of MAC and VLAN addresses.
Other restrictions with respect to Port VLAN and normal VLAN still apply
to not privileged/trusted VF.
Change-Id: I3a9529201b184c8873e1ad2e300aff468c9e6296
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure a VF is not trusted/privileged until its explicitly
set for trust through the new NDO op interface.
Change-Id: I476385c290d2b4901d8fceb29de43546accdc499
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accelerated RFS requires that ntuple filtering is enabled via
ethtool and driver supports ndo_rx_flow_steer.
When the ntuple filtering is enabled, we modify the l3_l4 ttc
rules to point on the aRFS flow tables and when the filtering
is disabled, we modify the l3_l4 ttc rules to point on the RSS
TIRs.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_rx_flow_steer ndo.
A new flow steering rule will be composed from the
skb 4-tuple and added to the hardware aRFS flow table.
Each rule is stored in an internal hash table, if such
skb 4-tuple rule already exists we update the corresponding
hardware steering rule with the new destination.
For garbage collection rps_may_expire_flow will be
invoked for a limited amount of old rules upon any
ndo_rx_flow_steer invocation.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create the following four flow tables for aRFS usage:
1. IPv4 TCP - filtering 4-tuple of IPv4 TCP packets.
2. IPv6 TCP - filtering 4-tuple of IPv6 TCP packets.
3. IPv4 UDP - filtering 4-tuple of IPv4 UDP packets.
4. IPv6 UDP - filtering 4-tuple of IPv6 UDP packets.
Each flow table has two flow groups: one for the 4-tuple
filtering (full match) and the other contains * rule for miss rule.
Full match rule means a hit for aRFS and packet will be forwarded
to the dedicated RQ/Core, miss rule packets will be forwarded to
default RSS hashing.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating CPU rmap and add entry for each IRQ.
CPU rmap is used in aRFS to get the RX queue number
of the RX completion interrupts.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the main flow table is used for two purposes:
One is to do mac filtering and the other is to classify
the packet l3-l4 header in order to steer the packet to
the right RSS TIR.
This design is very complex, for each configured mac address we
have to add eleven rules (rule for each traffic type), the same if the
device is put to promiscuous/allmulti mode.
This scheme isn't scalable for future features like aRFS.
In order to simplify it, the main flow table is split to two flow
tables:
1. l2 table - filter the packet dmac address, if there is a match
we forward to the ttc flow table.
2. TTC (Traffic Type Classifier) table - classify the traffic
type of the packet and steer the packet to the right TIR.
In this new design, when new mac address is added, the driver adds
only one flow rule instead of eleven.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slightly refactor and re-order the flow steering structs,
tables and data-bases for better self-containment and
flexibility to add more future steering phases
(tables/rules/data bases) e.g: aRFS.
Changes:
1. Move the vlan DB and address DB into their table structs.
2. Rename steering table structs to unique format: mlx5e_*_table,
e.g: mlx5e_vlan_table.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, namespace could be initialized only
with priorities with the same attributes.
Add support to initialize namespace with priorities
with different attributes(e.g. different number of levels).
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, consumers of the flow steering infrastructure can't
choose their own flow table levels and are limited to one
flow table per level. This just waste levels.
Instead, we introduce here the possibility to use multiple
flow tables in a level. The user is free to connect these
flow tables, while following the rule (FTEs in FT of level x
could only point to FTs of level y where y > x).
In addition this patch switch the order of the create/destroy
flow tables of the NIC(vlan and main).
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactors the flow steering namespace creation,
by changing the name num_fts to num_levels.
When new flow table is created, the driver assign new level
to this flow table therefore the meaning is equivalent.
Since downstream patches will introduce the ability to create more
than one flow table per level, the name num_fts is no
longer accurate.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This API is used for modifying the flow rule destination.
This is needed for modifying the pointed flow table by the
traffic type classifier rules to point on the aRFS tables.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new TIRs for direct access per RQ.
Now we have 2 available kinds of TIRs:
- indirect TIR per traffic type, each points to one RQT (RSS RQT)
same as before.
- New direct TIR per RQ, each points to RQT with a size of one
that forwards packets to that RQ only.
Driver will open max channels (num cores) direct TIRs by default,
they will be filled with the actual RQs once channels are allocated.
Needed for downstream aRFS and ethtool direct steering functionalities.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold the rtnl lock when calling vxlan_get_rx_port().
Fixes: b7aade1548 ("vxlan: break dependency with netdev drivers")
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch adds the required match table for device tree support
(and while at, fix the indent). It's also possible to specify the
MAC address in the DT blob.
Also add the corresponding binding documentation file.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current spi_read_buf function fails on SPI host masters which
are only half-duplex capable. Splitting the Tx and Rx part solves
this issue.
Tested on Raspberry Pi (full duplex) and I2SE Duckbill (half duplex).
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define PPP device handler for use with rtnetlink.
The only PPP specific attribute is IFLA_PPP_DEV_FD. It is mandatory and
contains the file descriptor of the associated /dev/ppp instance (the
file descriptor which would have been used for ioctl(PPPIOCNEWUNIT) in
the ioctl-based API). The PPP device is removed when this file
descriptor is released (same behaviour as with ioctl based PPP
devices).
PPP devices created with the rtnetlink API behave like the ones created
with ioctl(PPPIOCNEWUNIT). In particular existing ioctls work the same
way, no matter how the PPP device was created.
The rtnl callbacks are also assigned to ioctl based PPP devices. This
way, rtnl messages have the same effect on any PPP devices.
The immediate effect is that all PPP devices, even ioctl-based
ones, can now be removed with "ip link del".
A minor difference still exists between ioctl and rtnl based PPP
interfaces: in the device name, the number following the "ppp" prefix
corresponds to the PPP unit number for ioctl based devices, while it is
just an unrelated incrementing index for rtnl ones.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move PPP device initialisation and registration out of
ppp_create_interface().
This prepares code for device registration with rtnetlink.
While there, simplify the prototype of ppp_create_interface():
* Since ppp_dev_configure() takes care of setting file->private_data,
there's no need to return a ppp structure to ppp_unattached_ioctl()
anymore.
* The unit parameter is made read/write so that ppp_create_interface()
can tell which unit number has been assigned.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
On new GMAC4 IP, MAC_MDIO_address register has been updated, and bitmaps
changed. This patch takes into account those changes.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0c867c9bf8 ("vxlan: move Ethernet initialization to a separate
function") changed initialization order and as an unintended result, when the
user specifies additional link parameters (such as IFLA_ADDRESS) while
creating vxlan interface, those are overwritten by vxlan_ether_setup later.
It's necessary to call ether_setup from withing the ->setup callback. That
way, the correct parameters are set by rtnl_create_link later. This is done
also for VXLAN-GPE, as we don't know the interface type yet at that point,
and changed to the correct interface type later.
Fixes: 0c867c9bf8 ("vxlan: move Ethernet initialization to a separate function")
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Tested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new /sys/kernel/debug/ support to dump firmware mailbox commands
and replies for debugging purpose.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new /sys/kernel/debug/ support to dump a firmware mailbox command
issued and replies for debugging purpose.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indexes should generally be avoided. So we use reg rather than port-id to
index ports.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because cpld-ctrl-reg property is offset base on cpld-syscon property,
we make it as a cell in the cpld-syscon property.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a fixed-link DT subnode is used, the phy_device was looked up so
that a PHY ID string could be constructed and passed to phy_connect().
This is not necessary, as the device_node can be passed directly to
of_phy_connect() instead. This reuses the same codepath as if the
phy-handle DT property was used.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy-mode emac property was only being processed in the phy_id
or fixed-link cases. However if phy-handle was specified instead,
an error message would complain about the lack of phy_id or
fixed-link, and then jump past the of_get_phy_mode(). This would
result in the PHY mode defaulting to MII, regardless of what the
devicetree specified.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an emac node has a phy-handle property that points to something
which is not a phy, then a segmentation fault will occur when the
interface is brought up. This is because while phy_connect() will
return ERR_PTR() on failure, of_phy_connect() will return NULL.
The common error check uses IS_ERR(), and so missed when
of_phy_connect() fails. The NULL pointer is then dereferenced.
Also, the common error message referenced slave->data->phy_id,
which would be empty in the case of phy-handle. Instead, use the
name of the device_node as a useful identifier. And in the phy_id
case add the error code for completeness.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9e42f71526 ("drivers: net: cpsw: add
phy-handle parsing") saved the "phy-handle" phandle into a new cpsw_priv
field. However, phy connections are per-slave, so the phy_node field should
be in cpsw_slave_data rather than cpsw_priv.
This would go unnoticed in a single emac configuration. But in dual_emac
mode, the last "phy-handle" property parsed for either slave would be used
by both of them, causing them both to refer to the same phy_device.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When newlink creation fails at device-registration, the port->count
is decremented twice. Francesco Ruggeri (fruggeri@arista.com) found
this issue in Macvlan and the same exists in IPvlan driver too.
While fixing this issue I noticed another issue of missing unregister
in case of failure, so adding it to the fix which is similar to the
macvlan fix by Francesco in commit 3083796075 ("macvlan: fix failure
during registration v3")
Reported-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pch_gbe_tx_ring.tx_lock is only used in the hard_xmit handler and
in the transmit completion reaper called from NAPI context.
Compile-tested only. Potential victims Cced.
Someone more knowledgeable may check if pch_gbe_tx_queue could
have some use for a mmiowb.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Cress <andy.cress@us.kontron.com>
Cc: bryan@fossetcon.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The default Pegasus setup was to append the status and CRC at the end of each
received packet. The status bits are used to update various stats, but CRC has
been ignored. The new default is to not append CRC at the end of RX packets.
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_fill_bulk_urb() receives buffer length parameter 8 bytes larger
than what's allocated by alloc_skb(); This seems to be a problem with
older (pegasus usb-1.1) devices, which may silently return more data
than the maximal packet length.
Reported-by: Lincoln Ramsay <a1291762@gmail.com>
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 13a56b44 ("at803x: Add support for hardware reset") added a
work-around for a hardware bug on the AT8030. However, the work-around
was being called for all 803x PHYs, even those that don't need it.
Function at803x_link_change_notify() checks to make sure that it only
resets the PHY on the 8030, but it makes more sense to not call that
function at all if it isn't needed.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct mlx5e_channel_param is a large structure that is allocated
on the stack of mlx5e_open_channels, and with a recent change
it has grown beyond the warning size for the maximum stack
that a single function should use:
mellanox/mlx5/core/en_main.c: In function 'mlx5e_open_channels':
mellanox/mlx5/core/en_main.c:1325:1: error: the frame size of 1072 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
The function is already using dynamic allocation and is not in
a fast path, so the easiest workaround is to use another kzalloc
for allocating the channel parameters.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d3c9bc2743 ("net/mlx5e: Added ICO SQs")
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to calculate rps hash if it was not enabled. So this
patch export rps_needed and check it before trying to get rps
hash. Tests (using pktgen to inject packets to guest) shows this can
improve pps about 13% (when rps is disabled).
Before:
~1150000 pps
After:
~1300000 pps
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
----
Changes from V1:
- Fix build when CONFIG_RPS is not set
Signed-off-by: David S. Miller <davem@davemloft.net>
The size allocated for target->hwinfo and the number of bytes copied in it
should be consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
At forced 100 Full & Half duplex mode, chip may fail to set mode correctly
when cable is switched between long(~50+m) and short one.
As workaround, set to 10 before setting to 100 at forced 100 F/H mode.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix rx_bytes, tx_bytes and tx_frames error in netdev.stats.
- rx_bytes counted bytes excluding size of struct ethhdr.
- tx_packets didn't count multiple packets in a single urb
- tx_bytes included 8 bytes of extra commands.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error return err is not initialized and there is a possibility
that err is not assigned causing mv88e6xxx_port_bridge_join to
return a garbage error return status. Fix this by initializing err
to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configured in fixed link, the DaVinci emac driver sets the
priv->phydev to NULL and further ioctl calls to the phy_mii_ioctl()
causes the kernel to crash.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Fixes: 1bb6aa56bb ("net: davinci_emac: Add support for fixed-link PHY")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath9k
* fix a couple release old throughput regression on ar9281
iwlwifi
* add new device IDs for 8265
* fix a NULL pointer dereference when paging firmware asserts
* remove a WARNING on gscan capabilities
* fix MODULE_FIRMWARE for 8260
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXHjlZAAoJEG4XJFUm622brcgIAJ127uU9S/X3oM2EK76TdbV+
yZnp8Te57bK+ypXRP7YMaL7gevR3q9TEzQkY6ZQ0iMCZenQouxB/Wg9xBZjJ/ny0
dlVtmwM2sSvYdieTSftKGWLg3FH0FaJ1VXCJirLwrbs4Hbi2FqcGKMrLxflpqgW2
m1FkTZzCbjokaHZgoWJmlDM/UbPtTz8BJgLICRd7hJ4jJ2Mi2k32LCSxsXn0GbUG
naS6bDUGBcKjly9PKomY9y+rj897lm/m3rGKFJPkX/T7Klb1UMBLCj8NQIyF+/AX
vu1fLxMwlFyXnmRJAFPyj9T2Vok3aDjRuA9xck3MufxOFjOhEGJiPjZV3wNNFj8=
=aDY4
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.6
ath9k
* fix a couple release old throughput regression on ar9281
iwlwifi
* add new device IDs for 8265
* fix a NULL pointer dereference when paging firmware asserts
* remove a WARNING on gscan capabilities
* fix MODULE_FIRMWARE for 8260
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When certain firmware variants are selected (via the sfboot utility) the
SFC7000 and SFC8000 series NICs don't support RSS. The driver still
tries (and fails) to insert filters with the RSS flag, and the NIC fails
to pass traffic.
When the firmware reports RSS_LIMITED suppress allocating a default RSS
context. The absence of an RSS context is picked up in filter insertion
and RSS flags are discarded.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_disable() can not be called with bh disabled, move locking just
around myri10ge_ss_lock_napi() .
Patches fixes following bug:
[ 114.278378] BUG: sleeping function called from invalid context at net/core/dev.c:4383
<snip>
[ 114.313712] Call Trace:
[ 114.314943] [<ffffffff817010ce>] dump_stack+0x19/0x1b
[ 114.317673] [<ffffffff810ce7f3>] __might_sleep+0x173/0x230
[ 114.320566] [<ffffffff815b3117>] napi_disable+0x27/0x90
[ 114.323254] [<ffffffffa01e437f>] myri10ge_close+0xbf/0x3f0 [myri10ge]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-04-27
This series contains updates to i40e and i40evf.
Alex Duyck cleans up the feature flags since they are becoming pretty
"massive", the primary change being that we now build our features list
around hw_encap_features. Added support for IPIP and SIT offloads,
which should improvement in throughput for IPIP and SIT tunnels with
the offload enabled.
Mitch adds support for configuring RSS on behalf of the VFs, which removes
the burden of dealing with different hardware interfaces from the VF
drivers and improves future compatibility. Fix to ensure that we do not
panic by checking that the vsi_res pointer is valid before dereferencing
it, after which we can drink beer and eat peanuts.
Shannon does come housekeeping in i40e_add_fdir_ethtool() in preparation
for more cloud filter work. Added flexibility to the nvmupdate
facility by adding the ability to specify an AQ event opcode to wait on
after Exec_AQ request.
Michal adds device capability which defines if an update is available and
if a security check is needed during the update process.
Kamil just adds a device id to support X722 QSFP+ device.
Greg fixes an issue where a mirror rule ID may be zero, so do not return
invalid parameter when the user passes in a zero for a rule ID. Adds
support to steer packets to VSIs by VLAN tag alone while being in
promiscuous mode for multicast and unicast MAC addresses.
Jesse fixes the driver from offloading the VLAN tag into the skb any
time there was a VLAN tag and the hardware stripping was enabled, to
making sure it is enabled before put_tag.
v2: Dropped patch 8 ("i40e: Allow user to change input set mask for flow
director") while Kiran reworks a more generalized solution based
on feedback from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for W5500 chip.
W5500 has similar register and memory organization with W5100 and W5200.
There are a few important differences listed below but it is still
possible to share common code with W5100 and W5200.
* W5500 register and memory are organized by multiple blocks. Each one
is selected by 16bits offset address and 5bits block select bits.
But the existing register access operations take u16 address. This change
extends the addess by u32 address and put offset address to lower 16bits
and block select bits to upper 16bits.
This change also adds the offset addresses for socket register and TX/RX
memory blocks to the driver private data structure in order to reduce
conditional switches for each chip.
* W5500 has the different register offset for socket interrupt mask
register. Newly added internal functions w5100_enable_intr() and
w5100_disable_intr() take care of the diffrence.
* W5500 has the different register offset for retry time-value register.
But this register is only used to verify that the reset value is correctly
read at initialization. So move the verification to w5100_hw_reset()
which already does different things for different chips.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If PAGE_SIZE is bigger than BNXT_RX_PAGE_SIZE, that means the native CPU
page is bigger than the maximum length of the RX BD. Divide the page
into multiple 32K buffers for the aggregation ring.
Add an offset field in the bnxt_sw_rx_agg_bd struct to keep track of the
page offset of each buffer. Since each page can be referenced by multiple
buffer entries, call get_page() as needed to get the proper reference
count.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX BD length field of this device is 16-bit, so the largest buffer
size is 65535. For LRO and GRO, we allocate native CPU pages for the
aggregation ring buffers. It won't work if the native CPU page size is
64K or bigger.
We fix this by defining BNXT_RX_PAGE_SIZE to be native CPU page size
up to 32K. Replace PAGE_SIZE with BNXT_RX_PAGE_SIZE in all appropriate
places related to the rx aggregation ring logic.
The next patch will add additional logic to divide the page into 32K
chunks for aggrgation ring buffers if PAGE_SIZE is bigger than
BNXT_RX_PAGE_SIZE.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only MSI-X can be used on a VF. The driver should fail initialization
if it cannot successfully enable MSI-X.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add necessary Linux Ethernet driver support for promiscuous mode
operation. Add a flag so the VF knows it is in promiscuous mode
and two state flags to discreetly track multicast and unicast
promiscuous states.
Change-Id: Ib2f2dc7a7582304fec90fc917ebb7ded21ba1de4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
NFV use cases require the ability to steer packets to VSIs by VLAN tag
alone while being in promiscuous mode for multicast and unicast MAC
addresses. These two new functions support that ability.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was offloading the VLAN tag into the skb
any time there was a VLAN tag and the hardware stripping was
enabled. Just check to make sure it's enabled before put_tag.
Change-Id: Ife95290c06edd9a616393b38679923938b382241
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A mirror rule ID may be zero so do not return invalid parameter when the
user passes in a zero value for a rule ID.
Change-ID: I261b8c24725ce2c6ed32f859da81093dfcbe2970
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add device capability which defines if update is available and security
check is needed during update process.
Change-ID: I380787c878275e1df18b39198df3ee3666342282
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Minor overlapping changes in the conflicts.
In the macsec case, the change of the default ID macro
name overlapped with the 64-bit netlink attribute alignment
fixes in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been observed that sometimes AP's probe response is
received after scan duration gets completed for the channel.
This happens especially when wildcard scan is performed
along with specific SSID scan.
We will increase the time from 30 msecs to 40 msecs.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As 2.4Ghz channels are overlapping, sometimes AP responds to
probe request even if it's operating on neighbouring channel.
Currently firmware drops those scan entries, as current channel
doesn't match with APs channel.
This patch enables MWIFIEX_DISABLE_CHAN_FILT flag in scan
command to disable the feature so that better scan results
will be received in 2.4Ghz band.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In cfg80211 resume handler, we query wakeup reason from firmware and
report to cfg80211. if wowlan is disabled, connection is already
terminated during suspend. We don't need to query wakeup reason in this
case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that wakeup on GTK rekey failure wasn't reported
to cfg80211. This patch corrects the check so that all valid wakeup
reasons are reported.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
tx_packets counter is incremented for aggregated packets, when it had
already been incremented for the aggregated packet's constituent
parts. Removing the extra count.
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a packet is queued from the bridge, wmm_tx_pending is not
incremented, but when the packet is dequeued the counter is decremented.
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Should have converted 'if (trylock)' to 'lock'.
Fixes: a6086a8937 ("drivers: net: remove NETDEV_TX_LOCKED")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Renesas RZ/A1H manual names the software reset bit in the software reset
register (ARSTR) ARST which makes a bit more sense than the ARSTR_ARSTR name
used now by the driver -- rename the latter to ARSTR_ARST.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_check_reset() uses a bare number where EDMR_SRST_GETHER would fit,
i.e. the receive/trasmit software reset bits that comprise EDMR_SRST_GETHER
read as 1 while the corresponding reset is in progress and thus, when both
are 0, the reset is complete.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now as rx-vlan offload can be disabled, packets can be received
with vlan tag not stripped, which means is_first_ethertype_ip will
return false, for that we need to check if the hardware reported
csum OK so we will report CHECKSUM_UNNECESSARY for those packets.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ethtool -K <interface> rxvlan <on/off> to enable/disable
C-TAG vlan stripping by hardware.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add query MCIA, PMLP registers infrastructure and commands.
Add ethtool support for get_module_info() and get_module_eeprom()
callbacks.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the needed hardware command and mlx5_ifc structs for managing LED
control.
Add set_phys_id ethtool callback to support ethtool -p flag.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new access register named Ports Check Mask Register (PCMR) to
control all HW checks on port. With this register, the driver can
enable/disable Hardware FCS validation.
When RXALL is enabled/disabled using ndo_set_features, enable/disable
fcs check at HW.
User can change HW configuration using rx-all flag at ethtool.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current mlx5e ndo_set_features implementation, setting some features
can success while others can fail. Today, we return one error code which
doesn't reflect the current features status of the netdev at the end of
the ndo callback.
Set netdev->features with features which were successfully set in order
to keep the current status in case of failure. For this purpose, define
new Macro to set/unset specific feature in netdev->features.
This patch introduces a mechanism that uses feature handlers for each
feature.
Set features will call a generic handler, which will then call a specific
handler in his turn and update netdev->features according to it's return
value. Each specific handler is responsible to perform driver specific
actions, and updating params if needed.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose link_down_events counter through ethtool -S.
This counter is read from PPort statistics, then proccessed and stored as
a special handling software counter.
This counter is stored along software counters since it is the only PPort
counter that it's size is not 64 bits.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose counters providing information for each priority level (PCP) through
ethtool -S option and DCBNL.
This includes rx/tx bytes, frames, and pause counters.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VPort and software counters names are confusing and may be unclear, all
VPort counters now have a prefix of rx/tx_vport_*.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redesign ethtool statistics handling and reporting in the driver:
1. Move counters to a separate file (en_stats.h).
2. Remove unnecessary dependencies between stats and strings.
3. Use counter descriptors which hold a name and offset for each counter,
and will be used to decide which counters will be exposed.
For example when adding a new software counter to ethtool, instead of:
1. Add to stats struct.
2. Add to strings struct in the same order.
3. Change macro defining number of software counters.
The only thing needed is to link the new counter to a counter descriptor.
VPort counters are a set of hardware traffic counters created automatically
for each virtual port opened.
PPort counters are a set of counters describing per physical port
performance statistics.
These counters are gathered from hardware register and divided to groups
according to different protocols.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide rtnl_link_stats64 with information regarding physical errors to be
seen in ifconfig and ip tool.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace the trylock by a full spin_lock and remove TX_LOCKED return value.
Followup patch will remove TX_LOCKED from the kernel.
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These drivers already call netif_stop_queue() so we should not be called
unless tx space is available. Just free the skb and return TX_OK.
Followup patch will remove NETDEV_TX_LOCKED from the kernel.
Cc: linux-parisc@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
similar to atl1c: lock is only used in ndo_start_xmit, but we also
advertised LLTX, so remove that as well and let core stack handle
tx locking.
Allows to remove the TX_LOCKED return value from the driver.
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
AFAICS this is safe: the lock is only used in the .ndo_start_xmit
function and this driver does not set LLTX.
Gets rid of TX_LOCKED return value, followup patches will remove it.
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann asked that get_phy_device() returns either NULL or the error
value, not both on error. Do as he said, return ERR_PTR(-ENODEV) instead
of NULL when the PHY ID registers read as all ones.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_dev_init() is now always called with 'true' as the 2nd argument,
so that there's no more sense in having 2 parameters to this function...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvtap_device_event(NETDEV_UNREGISTER) should check vlan->minor to
determine if it is being invoked in the context of a macvtap_newlink
that failed, for example in this code sequence:
macvtap_newlink
macvlan_common_newlink
register_netdevice
call_netdevice_notifiers(NETDEV_REGISTER, dev)
macvtap_device_event(NETDEV_REGISTER)
<fail here, vlan->minor = 0>
rollback_registered(dev);
rollback_registered_many
call_netdevice_notifiers(NETDEV_UNREGISTER, dev);
macvtap_device_event(NETDEV_UNREGISTER)
<nothing to clean up here>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If macvlan_common_newlink fails in register_netdevice after macvlan_init
then it decrements port->count twice, first in macvlan_uninit (from
register_netdevice or rollback_registered) and then again in
macvlan_common_newlink.
A similar problem may exist in the ipvlan driver.
This patch consolidates modifications to port->count into macvlan_init
and macvlan_uninit (thanks to Eric Biederman for suggesting this approach).
v3: remove macvtap specific bits.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PF minimum bandwidth update
or configuration notified by management firmware.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PF maximum bandwidth update
or configuration notified by management firmware.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds relevant APIs needed to configure WFQ
(Weighted fair queueing) values for the vports. WFQ configuration
is used per vport basis when minimum bandwidth update/configuration
is notified to the PF by the management firmware.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware can send a set of asynchronous replies through FW_PORT_CMD
with DCBX information when that's negotiated with the Link Peer. The old
code always assumed that a FW_PORT_CMD reply was always a Get Port
Information message. This change conditionalizes the code to only handle
the Get Port Information messages and throws a warning if we don't
understand what we've been given.
Also refactor t4_handle_fw_rpl() so that core functionality performed by
t4_handle_get_port_info() for a specified port.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor t4_port_init() so that the core functionality is done by
t4_init_portinfo() for a particular port. Also rename variables to
sensible ones.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decode and log port module error, unknown modules and unsupported
modules.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There could be race between t4_eth_xmit() and t4_free_sge_resources() while
freeing tx descriptors, take txq lock in t4_free_sge_resources(). We need
to stop the xmit frame path which runs in bottom half context while
unloading the driver using _bh variant of the lock. This is to prevent
the deadlock between xmit and driver unload.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new routine to print out general adapter information (various version
numbers, adapter name, part number, serial number, etc.) and remove
redundant information dumped in the Port Information.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-04-26
Here's another set of Bluetooth & 802.15.4 patches for the 4.7 kernel:
- Cleanups & refactoring of ieee802154 & 6lowpan code
- Security related additions to ieee802154 and mrf24j40 driver
- Memory corruption fix to Bluetooth 6lowpan code
- Race condition fix in vhci driver
- Enhancements to the atusb 802.15.4 driver
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PF driver reports proper support, allow the PF driver to
configure RSS on the behalf of the VF driver. This will allow for RSS
support on future hardware without changes to the VF driver.
Unfortunately, the old RSS code still needs to stay as the driver needs
to be compatible with PF drivers that don't support this interface. But
this change still simplifies the data structures a bunch and makes this
code simpler to read and maintain.
Change-ID: I0375aad40788ecdc0cb24d5cfeccf07804e69771
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To add a little flexibility to the nvmupdate facility, this code adds the
ability to specify an AQ event opcode to wait on after the Exec_AQ request.
Change-ID: Iddbfd63c3de8df3edb9d3e90678b08989bc4946e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ath.git patches for 4.7. Major changes:
ath10k
* implement set_tsf() for 10.2.4 branch
* remove rare MSI range support
* remove deprecated firmware API 1 support
ath9k
* add module parameter to invert LED polarity
wcn36xx
* fixes to get the driver properly working on Dragonboard 410c
A little bit of code cleanup in prep for more cloud filter work.
Change-ID: I0dc33ce0d4c207944336a07437640fef920c100c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Under some circumstances the driver remove function may be called before
the driver is fully initialized. So we can't assume that we know where
our towel is at, or that all of the data structures are initialized.
To ensure that we don't panic, check that the vsi_res pointer is valid
before dereferencing it. Then drink beer and eat peanuts.
Change-ID: If697b4db57348e39f9538793e16aa755e3e1af03
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for configuring RSS on behalf of the VFs. This removes the
burden of dealing with different hardware interfaces from the VF
drivers, allowing for better future compatibility.
Change-ID: Icea75d3f37241ee8e447be5779e5abb53ddf04c0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Looking over the documentation it turns out enabling IPIP and SIT offloads
for i40e is pretty straightforward. As such I decided to enable them with
this patch. In my testing I am seeing an improvement of 8 to 10 Gb/s
for IPIP and SIT tunnels with this offload enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The feature flags list for i40e and i40evf is beginning to become pretty
massive. I plan to add another 4 or so features to these drivers and
duplicating the flags for each and every flags list is becoming a bit
repetitive.
The primary change here is that we now build our features list around
hw_encap_features. After that we assign that to vlan_features,
hw_features, and finally map that onto features. In addition we end up
throwing features onto hw_encap_features that end up having no effect such
as the Rx offloads and SCTP_CRC. However that should have no impact and
makes things a bit easier for us as hw_encap_features is one of the less
updated features maps available.
For i40evf I went through and sanity checked a few features as well.
Specifically RXCSUM was being set as a read-only feature which didn't make
much sense. I have updated things so we can clear the NETIF_F_RXCSUM flag
since that is really a software feature and not a hardware one anyway so
disabling it is just a matter of ignoring the result from the hardware.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 97f95c93c8 ("iwlwifi: remove support for fw older than
-16.ucode") we accidentally changed the fw version reading code for
DVM devices. The code intended to remove the old fw version API,
because all MVM firmwares version 16 and above that we support don't
use it anymore. But DVM devices still use the old FW API.
Fix that by bringing the code back in.
Reported-by: Pat Erley <pat-lkml@erley.org>
Tested-by: Kalle Valo <kvalo@codeaurora.org>
Fixes: 97f95c93c8 ("iwlwifi: remove support for fw older than-16.ucode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If rt2800usb is loaded with nohwcrypt=1, mac80211 takes
care of the crypto with software encryption/decryption
and thus, MFP can be used.
Tested for secured mesh using ath9k_htc and ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch complains about this code:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c:335 brcmf_rx_hdrpull()
error: we previously assumed '*ifp' could be null (see line 333)
The problem is that we recently changed these from "ifp" to "*ifp" but
there was one that we didn't update.
- if (ret || !ifp || !ifp->ndev) {
+ if (ret || !(*ifp) || !(*ifp)->ndev) {
if (ret != -ENODATA && ifp)
^^^
- ifp->stats.rx_errors++;
+ (*ifp)->stats.rx_errors++;
I have updated it to *ifp as well. We always call this function is a
non-NULL "ifp" pointer, btw.
Fixes: c462ebcdfe ('brcmfmac: create common function for handling brcmf_proto_hdrpull()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB8XXX_FW_MAX_RETRY is 3. We were using a post-op loop
"while (retries--) {" but then the lines after that assume the loop
exits with retries set to zero.
I've fixed this by changing to a pre-op loop. I started with retries
set to 4 instead of 3 so that we still go through the loop the same
number of times.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We accidentally return success instead of -ENOMEM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is nothing 8723au specific about rtl8723au_iqk_phy_iq_bb_reg so
rename the array to rtl8xxxu_iqk_phy_iq_bb_reg.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This renames rtl8723bu_simularity_compare() to
rtl8xxxu_gen2_simularity_compare() to reflect it is used for all gen2
parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This renames rtl8723b_channel_to_group() to
rtl8xxxu_gen2_channel_to_group() to reflect it is used by all
currently supported gen2 parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All currently supported gen1 parts use the same mac_init_table, so
rename it to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All gen1 parts use the same enable_rf() function, so rename it to
reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All gen1 parts use the same interface for setting TX power, so rename
the function to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All gen1 parts use the same init_phy_bb() function, so rename it to
reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All supported gen1 parts use the same phy_iq_calibrate() function
(unlike their gen2 counterparts). Rename the function to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All currently supported gen1 parts use the same function for updating
the rate mask, so rename it to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All supported gen1 parts use the same config_channel() function, so
rename it to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All currently supported gen1 parts use the same disable_rf() routine,
so rename the function to reflect that.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
