Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos5250 and Exynos542x SoCs have the same CEC hardware module as
Exynos4 SoC series, so enable support for it using the same compatible
string.
Tested on Odroid XU3 (Exynos5422) and Google Snow (Exynos5250) boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In Odroid XU3 Lite board, the temperature levels reported for thermal
zone 0 were weird. In warm room:
/sys/class/thermal/thermal_zone0/temp:32000
/sys/class/thermal/thermal_zone1/temp:51000
/sys/class/thermal/thermal_zone2/temp:55000
/sys/class/thermal/thermal_zone3/temp:54000
/sys/class/thermal/thermal_zone4/temp:51000
Sometimes after booting the value was even equal to ambient temperature
which is highly unlikely to be a real temperature of sensor in SoC.
The thermal sensor's calibration (trimming) is based on fused values.
In case of the board above, the fused values are: 35, 52, 43, 58 and 43
(corresponding to each TMU device). However driver defined a minimum value
for fused data as 40 and for smaller values it was using a hard-coded 55
instead. This lead to mapping data from sensor to wrong temperatures
for thermal zone 0.
Various vendor 3.10 trees (Hardkernel's based on Samsung LSI, Artik 10)
do not impose any limits on fused values. Since we do not have any
knowledge about these limits, use 0 as a minimum accepted fused value.
This should essentially allow accepting any reasonable fused value thus
behaving like vendor driver.
The exynos5420-tmu-sensor-conf.dtsi is copied directly from existing
exynos4412 with one change - the samsung,tmu_min_efuse_value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Provide human readable names for all power domains defined in Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
UART modules can use DMA for offloading data transfers and reducing
interrupts, so enable this feature for Exynos5 boards. Tested on
Google ChromeBook Snow (Exynos5250), Odroid XU (Exynos5410) and Odroid
XU3 (Exynos5422) boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
This brings support for Hardkernel's Odroid XU board. It was the first
design with big.LITTLE SoC from Samsung: Exynos5410. The board is not
very popular. Newer XU3 and XU4 got more attention.
Board details:
1. Exynos5410 octa-core (A15+A7, however as of now only one cluster is
enabled),
2. 2 GB DDR3 RAM,
3. PowerVR SGX544MP3 GPU (not enabled in DTS),
4. USB 3.0 Host x 1, USB 3.0 OTG x 1, USB 2.0 Host x 4,
5. HDMI 1.4a, MIPI DSI and Display Port (Display Port not on all of
revisions though),
6. eMMC 4.5 and microSD slots.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7u0/
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-odroid-xu-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch for adding Exynos 5410 Odroid XU board for v4.8.
This brings support for Hardkernel's Odroid XU board. It was the first
design with big.LITTLE SoC from Samsung: Exynos5410. The board is not
very popular. Newer XU3 and XU4 got more attention.
Board details:
1. Exynos5410 octa-core (A15+A7, however as of now only one cluster is
enabled),
2. 2 GB DDR3 RAM,
3. PowerVR SGX544MP3 GPU (not enabled in DTS),
4. USB 3.0 Host x 1, USB 3.0 OTG x 1, USB 2.0 Host x 4,
5. HDMI 1.4a, MIPI DSI and Display Port (Display Port not on all of
revisions though),
6. eMMC 4.5 and microSD slots.
* tag 'samsung-dt-odroid-xu-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (28 commits)
ARM: dts: exynos: Add watchdog and Security SubSystem to Exynos5410
ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board
ARM: dts: exynos: Add Thermal Management Unit to Exynos5410
ARM: dts: exynos: Interrupt for USB DWC3-1 differs between Exynos5420 and 5410
dt-bindings: clock: Add watchdog and SSS clock IDs to Exynos5410
dt-bindings: clock: Add TMU clock ID to Exynos5410
ARM: dts: exynos: Add RTC and I2C to Exynos5410
ARM: dts: exynos: Add I2C, PWM and UART pinctrl to Exynos5410
ARM: dts: exynos: Move HSI2C nodes to exynos54xx.dtsi
ARM: dts: exynos: Add initial support for Odroid XU board
ARM: dts: exynos: Add USB to Exynos5410
ARM: dts: exynos: Move common Exynos5410/542x/5800 nodes to new DTSI
ARM: dts: exynos: MCT is not an interrupt controller and extend length of iomap
ARM: dts: exynos: Enable UART3 on Exynos5410
ARM: dts: exynos: Include common exynos5 in exynos5410.dtsi
ARM: dts: exynos: Move Exynos5250 and Exynos5420 nodes under soc
ARM: dts: exynos: Use phandle to get parent node in exynos5250-snow
ARM: dts: exynos: Prepare for inclusion of exynos5.dtsi in exynos5410.dtsi
ARM: dts: exynos: Move common nodes to exynos5.dtsi
ARM: dts: exynos: Split Odroid XU3 LEDs to separate DTSI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Move watchdog and Security SubSystem nodes from exynos5420.dtsi to file
shared with Exynos5410 and configure the clocks on the latter.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
On Exynos5410 the SPI interrupt for second USB DWC3 (called DRD: Dual
Role Device) is different - 200 instead of 73.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The USI/HSI2C nodes can be mostly shared between Exynos5420 and
Exynos5410 so move them to common DTSI.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Move USB 3.0 DWC and 2.0 EHCI/OHCI nodes from exynos5420.dtsi to
exynos54xx.dtsi common for entire family. For Exynos542x/5800 this
should not have functional impact but for Exynos5410 this effectively
adds USB support.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
The Exynos5410/542x/5800 are very similar designs. Create a new
DTSI with common nodes to remove DTS duplication. Although currently
only MCT and SysRAM are shared but in future more nodes will be added to
the common file.
The patch should not have functional impact.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Multi-Core Timer generates interrupts but it is not really an interrupt
controller so remove the "interrupt-controller" and "interrupt-cells"
properties. Additionally extend the length of mapped memory to cover all
registers (last SFR is at 0x0A40).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
The conventions is to put SoC devices under 'soc' node. In fact other
our DTSes (like exynos3250.dtsi or exynos5410.dtsi) already follow it.
Adjust exynos5250 and exynos5420 DTSI to follow this convention. This is
also necessary for the upcoming change in exynos5410.dtsi to inherit
from common exynos5.dtsi.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Exynos5420 and Exynos5250 share some nodes: the PWM, syscon
(sysreg_system_controller) and first four I2C controllers. Move them to
parent DTSI to avoid duplication.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Since commit 218e149613 ("i2c: exynos5: add support for HSI2C on
Exynos5260 SoC") the "samsung,exynos5-hsi2c" is deprecated in favor of
SoC version specific: "samsung,exynos5250-hsi2c".
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The MFC IP is also inter-connected by an Async-Bridge so the CLK_ACLK333
has to be ungated during a power domain switch. Trying to do it when the
clock is gated will fail and lead to an imprecise external abort error
when the driver tries to access the MFC registers with the PD disabled.
For example, if the s5p-mfc module is removed and the MFC PD turned off:
[ 186.835606] Power domain power-domain@10044060 disable failed
[ 186.835671] s5p-mfc 11000000.codec: Removing 11000000.codec
[ 186.837670] Power domain power-domain@10044060 disable failed
And when the module is inserted again:
[ 2395.176956] s5p_mfc_wait_for_done_dev:34: Interrupt (dev->int_type:0, command:12) timed out
[ 2395.177031] s5p_mfc_init_hw:272: Failed to load firmware
[ 2395.177384] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
[ 2395.177441] pgd = ec3b4000
[ 2395.177467] [00000000] *pgd=00000000
[ 2395.177507] Internal error: : 1406 [#1] PREEMPT SMP ARM
[ 2395.177550] Modules linked in: s5p_mfc mwifiex_sdio mwifiex uvcvideo s5p_jpeg v4l2_mem2mem videobuf2_vmalloc videobuf2_dma_contig videobuf2_memops videobuf2_v4l2 videobuf2_core v4l2_common videodev media [last unloaded: s5p_mfc]
[ 2395.177774] CPU: 1 PID: 2382 Comm: v4l_id Tainted: G W 4.6.0-rc6-next-20160502-00010-g7730dc64d2c1-dirty #179
[ 2395.177857] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 2395.177906] task: ed275500 ti: e6c8c000 task.ti: e6c8c000
[ 2395.177996] PC is at s5p_mfc_reset+0x1c4/0x284 [s5p_mfc]
[ 2395.178057] LR is at s5p_mfc_reset+0x1a4/0x284 [s5p_mfc]
This patch fixes this issue by adding the CLK_ACLK333 as an Async-Bridge
clock for the MFC power domain, so the PD configuration works properly.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT binding
in a way that only provides compatibility with old DT blobs on new
kernels but not vice versa. As a consequence, the DT changes
are based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on
other changes that got merged through the clk maintainer tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I0Be
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT
binding in a way that only provides compatibility with old DT blobs on
new kernels but not vice versa. As a consequence, the DT changes are
based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on other
changes that got merged through the clk maintainer tree"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: dts: exynos: Add support of Bus frequency using VDD_INT for exynos5422-odroidxu3
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos542x SoC
ARM: dts: exynos: Add NoC Probe dt node for Exynos542x SoC
ARM: dts: exynos: Add support of bus frequency for exynos4412-trats/odroidu3
ARM: dts: exynos: Expand the voltage range of buck1/3 regulator for exynos4412-odroidu3
ARM: dts: exynos: Add support of bus frequency using VDD_INT for exynos3250-rinato
ARM: dts: exynos: Add exynos4412-ppmu-common dtsi to delete duplicate PPMU nodes
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4210
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos3250
ARM: dts: exynos: Add DMC bus frequency for exynos3250-rinato/monk
ARM: dts: exynos: Add DMC bus node for Exynos3250
ARM: tegra: Enable XUSB on Nyan
ARM: tegra: Enable XUSB on Jetson TK1
ARM: tegra: Enable XUSB on Venice2
ARM: tegra: Add Tegra124 XUSB controller
ARM: tegra: Move Tegra124 to the new XUSB pad controller binding
ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
...
This patch adds the AMBA bus nodes using VDD_INT for Exynos542x SoC.
Exynos542x has the following AMBA buses to translate data between
DRAM and sub-blocks.
Following list specifies the detailed correlation between sub-block and clock:
- CLK_DOUT_ACLK400_WCORE clock for WCORE's AXI
- CLK_DOUT_ACLK100_NOC for NoC (Network on Chip)'s AXI
- CLK_DOUT_PCLK200_FSYS for FSYS's APB
- CLK_DOUT_ACLK200_FSYS for FSYS's AXI
- CLK_DOUT_ACLK200_FSYS2 for FSYS2's AXI
- CLK_DOUT_ACLK333 for MFC's AXI
- CLK_DOUT_ACLK266 for GEN's AXI
- CLK_DOUT_ACLK66 for PERIC/PERIR's AXI
- CLK_DOUT_ACLK333_G2D for G2D's AXI
- CLK_DOUT_ACLK266_G2D for ACP's AXI
- CLK_DOUT_ACLK300_JPEG for JPEG's AXI
- CLK_DOUT_ACLK166 for JPEG's APB
- CLK_DOUT_ACLK300_DISP1 for FIMD's AXI
- CLK_DOUT_ACLK400_DISP1 for DISP1's AXI
- CLK_DOUT_ACLK300_GSCL for GSCL Scaler's AXI
- CLK_DOUT_ACLK400_MSCL for MSCL's AXI
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the NoCP (Network on Chip Probe) Device Tree node
to measure the bandwidth of memory and g3d in Exynos542x SoC.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch changes the compatible of Exynos5420 fimd
to "exynos5420-fimd". To support MIC bypass from display
path, the new compatible is introduced for Exynos5420.
Cc: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fix following DTC warnings in all Exynos542x/5800 boards:
Warning (unit_address_vs_reg): Node /video-phy@10040728 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /video-phy@10040714 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12000000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12000000/dwc3 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /usb@12400000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12400000/dwc3 has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
The compatible string "simple-bus" is well defined in ePAPR, while
I see no documentation for the "arm,amba-bus" arnywhere in ePAPR or
Documentation/devicetree/.
DT is also used by other projects than Linux kernel. It is not a
good idea to rely on such an unofficial binding.
This commit
- replaces "arm,amba-bus" with "simple-bus"
- drops "arm,amba-bus" where it is used along with "simple-bus"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for restoring GScaler parent clocks configuration when GSCL
power domain is turned on.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For Exynos542x/5800 platforms, add CPU operating points
for migrating from Exynos specific cpufreq driver to using
generic cpufreq driver.
Changes by Bartlomiej:
- split Exynos5420 support from the original patch
- merged Exynos5422 fixes from Ben
Changes by Ben Gamari:
- Port to operating-points-v2
Cc: Doug Anderson <dianders@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Exynos5420 and Exynos5800 boards boot from big core (A15) but
Exynos5422 boards choose otherwise: LITTLE core (A7) (on Exynos5422 this
is property of the board - configurable by pulling up/down gpg2-1).
To make user-visible CPU ordering more consistent the 'cpus' node was
overridden by exynos5422-cpus.dtsi.
However this is a little bit ugly and error-prone. Overriding the CPU
child nodes requires to basically reverse what was done initially in
exynos5420.dtsi.
Instead, split CPU configuration entirely to separate files which should
be included by board DTS.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanho Park <parkch98@gmail.com>
The s5p-sss crypto HW acceleration driver supports only AES algorithms
thus it accesses only registers from feeder (offset 0x0, length 0x100)
and AES (offset 0x200, length 0x100) blocks of Security SubSystem (SSS).
The exynos-rng Pseudo Random Number Generator driver accesses only PRNG
block at offset 0x400 (length 0x100).
Narrow the size of memory mapped by s5p-sss driver so both drivers can
be loaded at the same time.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
This patch adds device node for Rotator device and it's SYSMMU to Exynos
542x device tree file.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The sysmmu_fimd1_1 should bind the clock CLK_SMMU_FIMD1M1, not the clock
CLK_SMMU_FIMD1M0. CLK_SMMU_FIMD1M0 is a clock for the sysmmu_fimd1_0.
This wrong clock binding causes the problem that is blocked in iommu_map
function when IOMMU is enabled and exynos-drm driver tries to allocate
buffer via DMA mapping API on Odroid-XU3 board.
Fixes: b700451678 ("ARM: dts: add sysmmu nodes for exynos5420")
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The dtc compiler combines all the defined nodes that have the same path
so a device node definition can be in one file and later be extended in
another one.
That's the case of the Exynos5420 pinctrl device nodes that are defined
in the exynos5420.dtsi file and extended in exynos5420-pinctrl.dtsi.
But since the exynos5420.dtsi file includes the exynos5420-pinctrl.dtsi
before the pinctrl device nodes are actually defined, the definition of
the pinctrl device nodes happens in exynos5420-pinctrl.dtsi and are
extended in exynos5420.dtsi.
That is the opposite of the original intention so even when there is no
difference in practice, the exynos5420-pinctrl.dtsi include should be
moved at the end of the exynos5420.dtsi file after the pinctrl device
nodes have been already defined.
This will also allow to later change the exynos5420-pinctrl.dtsi file
to use labels instead of full paths to extend the pinctrl nodes. Since
keeping the include at the top, would cause a dtc build error due the
pinctrl labels not being defined yet.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds System MMU nodes to all defined devices that are
specific to Exynos5420/5800/5422 series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add nodes for jpeg codec in Exynos5420 SoC.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[k.kozlowski: fixed up minor differences for applying]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes. Additionally remove duplicated serial and uart labels
for serial.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Replace fixed parent with last parent (obtained with clk_get_parent())
of clocks for devices in mfc and disp power domains. This should improve
behavior if such clocks were reparented by the drivers and new parents
are different than those specified in DTS.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add MAX98090 audio codec, I2S interface and the sound nodes
to support audio on exynos5422-odroidxu3 board. Now we can
support audio using simple-audio-card DT binding.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Since commit e4b3d38088 ("phy: exynos-video-mipi: Fix regression by
adding support for PMU regmap") the syscon property is required in
samsung,s5pv210-mipi-video-phy nodes, but this DTS hadn't been updated
yet.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Commit ea08de16eb ("ARM: dts: Add DISP1 power domain for exynos5420")
added a device node for the Exynos5420 DISP1 power domain but dit not
make the DP controller a consumer of that power domain.
This causes an "Unhandled fault: imprecise external abort" error if the
exynos-dp driver tries to access the DP controller registers and the PD
was turned off. This lead to a kernel panic and a complete system hang.
Make the DP controller device node a consumer of the DISP1 power domain
to ensure that the PD is turned on when the exynos-dp driver is probed.
Fixes: ea08de16eb ("ARM: dts: Add DISP1 power domain for exynos5420")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
- Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IPgJ
-----END PGP SIGNATURE-----
Merge tag 'irqchip-core-4.1-3' of git://git.infradead.org/users/jcooper/linux into irq/core
irqchip core change for v4.1 (round 3) from Jason Cooper
Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
- for exynos3250
: add assigned clock parents for CMU nodes
- for exynos4412-odroid
: add eMMC reset line
- for exynos5250
: fixed typo for interrupt-cells
- for exynos5250-snow
: define stdout-path property
: represent bridge and panel connection
: enable wifi power-on and add cap-sdio-irq to wifi mmc node
- for exynos5250-spring
: define stdout-path property
- for exynos5420
: fixed typo for interrupt-cells
: add async-bridge clocks for gsc and disp1 PDs
- for exynos5420 boards
: Mux XMMCnDATA[0] pad correctly
- for exynos5420-odroidxu3
: add eMMC reset line
- for Peach boards
: add HS400 support and define stdout-path property
: add mclk entry and add WiFi module support
: represent bridge and panel connection
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJVHDABAAoJEA0Cl+kVi2xqaasP/04A2twJLhYzqobi9fdNOv+U
E14Z1qWv5XBnkkD4LewVCDTShVx+T6LDCAesJoaEcgK+ox8ZgcH4TlEslQ8pQdR5
3TjT1Tf/Qeldtri0Lb8jX9k7G6A+ogT1ywhMNUXTqLP3GFTgnIj/36MPlt22zYWp
w006UXDwYLrjFkX99lQr1XpDhPnTv3H+72ZPdDlRk59wxFnymQ0gb4Ong8bbKd56
0/35bw/fhHMTAtSVjVl6j5yblDl4NSh3y+T7Ftt59TKBBfhD0JB7VaT3OXmNqX52
mdhnT5MAK+l0LjW6a2xkbq+xgNAqSFhpX1d4RWwKheSa9aF2usCZnWxwzqCkLioa
v4O20gMlOkpq7pXduX+neJPgq1j1fls0ZlWKCTtgckmXCJQxdBkRYvuLeAz/QfGK
JZu/awQMLo8ebs8UaH1+mkpGsUzVzW5aGBw0ROH8N27R8xCmqujxMr9k6g9TRDTO
kFxIJAAsP1B/zEbvoI6LsPFPISBJjjjdOXClU72qrwNWuESWYsG71iI5PU6m2/bZ
Eq2qWa1dkOh3Lp/FVW6zXEGk60I1+ghd7VBC3GhbzDb4L5RMqeuRtD41DHKp4i67
UhymfzXuzyC1FDzI8qwySm2GApGhwN2mJwXc4bdOkABznytLJ5GumE6jc13806+/
mnUb7ksYakVIJyjVCE88
=Sz8u
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v4.1" from Kukjin Kim:
- for exynos3250
: add assigned clock parents for CMU nodes
- for exynos4412-odroid
: add eMMC reset line
- for exynos5250
: fixed typo for interrupt-cells
- for exynos5250-snow
: define stdout-path property
: represent bridge and panel connection
: enable wifi power-on and add cap-sdio-irq to wifi mmc node
- for exynos5250-spring
: define stdout-path property
- for exynos5420
: fixed typo for interrupt-cells
: add async-bridge clocks for gsc and disp1 PDs
- for exynos5420 boards
: Mux XMMCnDATA[0] pad correctly
- for exynos5420-odroidxu3
: add eMMC reset line
- for Peach boards
: add HS400 support and define stdout-path property
: add mclk entry and add WiFi module support
: represent bridge and panel connection
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Fixed typo interrupt-cells for exynos5420 and exynos5250
ARM: dts: Add HS400 support for exynos5420 and exynos5800
ARM: dts: add async-bridge clocks to gsc power domain for exynos5420
ARM: dts: add async-bridge clocks to disp1 power domain for exynos5420
dt-bindings: add asynchronous bridge clock for exynos
ARM: dts: Define stdout-path property for exynos5250-spring
ARM: dts: Define stdout-path property for exynos5250-snow
ARM: dts: Define stdout-path property for Peach boards
ARM: dts: Add assigned clock parents to CMU node for exynos3250
ARM: dts: Add mclk entry for Peach boards
ARM: dts: Add WiFi module support for Peach boards
ARM: dts: Mux XMMCnDATA[0] pad correctly for Exynos5420 boards
ARM: dts: add eMMC reset line for exynos5422-odroidxu3
ARM: dts: add eMMC reset line for exynos4412-odroid-common
ARM: dts: represent bridge and panel connection for exynos5420-peach-pit
ARM: dts: represent bridge and panel connection for exynos5250-snow
ARM: dts: Add cap-sdio-irq to wifi mmc node for exynos5250-snow
ARM: dts: Enable wifi power-on for exynos5250-snow
Signed-off-by: Olof Johansson <olof@lixom.net>
Changes fixes the misspelled of #interrups-cell.
arch/arm/boot/dts/exynos5420.dtsi:224: WARNING: 'interrups'
may be misspelled - perhaps 'interrupts'?
Tested on OdroidXU3 board.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
[kgene@kernel.org: added fixing same typo in exynos5250]
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Exynos has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.
This patch does just this, updating the DT files to actually
reflect what the HW provides.
BIG FAT WARNING: because the DTs were so far lying by not
exposing the fact that the PMU block is actually the first
interrupt controller in the chain for RTC, kernels with this patch
applied wont have any suspend-resume facility when booted
with old DTs, and old kernels with updated DTs may not even boot.
Also, I strongly suspect that there is more than two wake-up
interrupts on these platforms, but I leave it to the maintainers
to fix their mess.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088693-15724-2-git-send-email-marc.zyngier@arm.com
[ jac: squash in maz's fixup from
https://lkml.kernel.org/r/5506989D.9050703@arm.com ]
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Both GSCALER IPs in gsc power domain have async-bridges (to FIMD and MIXER),
therefore their clocks should be enabled during power domain switch.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
FIMD and MIXER IPs in disp1 power domain have async-bridges (to GSCALER),
therefore their clocks should be enabled during power domain switch.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Mixed block needs to control hdmi clock to properly perform power on/off
operation, so add 'hdmi' clock also to mixer nodes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Presented device tree bindings provide data already hardcoded in the
exynos_tmu_data.c file.
After this commit, it should be possible to reuse common thermal core
framework in Exynos SoCs.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
The DISP1 power domain on Exynos5420 SoC includes the FIMD1, MIXER
and HDMI modules. Add a device node for this power domain and mark
these modules as consumer of the DISP1 power domain.
When a power domain is powered on and off, the input clocks of the
devices attached to it are reparented. So a reference to the input
and parent clocks of the devices are needed to manage that.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
