The Si2141 needs two distinct commands for powerup/reset, otherwise it
will not respond to chip revision requests. It also needs a firmware
to run properly.
Cc: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
'Reset' loop does not look correct. I tested it very many times and
it never repeated those commands. If problem, it tries to solve,
really occurs on some situations better solution should be find out.
There is another patch which does not have such hackish looking loop.
Lets change to it.
Cc: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The XV601/709 encodings are special: they signal limited range, but use the full range
to encode a larger gamut with R', G' and B' values outside the [0-1] range.
So don't clamp to limited range for these two encodings.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If DMA does not support INTERLEAVE, deinterlace_probe() breaks off
initialization, releases dma channel, but returns zero.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
TRY_FMT already disables the YUYV format if the VDOA is not available.
ENUM_FMT must do the same.
Fixes: d40e98c13b ("[media] coda: support YUYV output if VDOA is used")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Even if field order is set to V4L2_FIELD_ALTERNATE, the width and height
values in struct v4l2_mbus_framefmt still refer to frame size, not field
size.
Fixes: 4f57d27be2 ("[media] tvp5150: fix tvp5150_fill_fmt()")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To let userspace propagate formats downstream in a media controller
scenario, the video source pad (now pad 1, DEMOD_PAD_VID_OUT) must allow
setting and getting the format. Incidentally, tvp5150_fill_fmt was
implemented for this pad, not for the new analog input pad (now pad 0,
DEMOD_PAD_IF_INPUT).
Fixes: 55606310e7 ("[media] tvp5150: create the expected number of pads")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The call to v4ls_m2m_get_vq is only used to get the return value
which is not being used, so it appears to be redundant and can
be removed.
Detected with CoverityScan, CID#1420674 ("Useless call")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The em28xx driver still used the soc_camera.h header for the ov2640
driver. Since this driver no longer uses soc_camera, that include can
be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MC support is needed by the em28xx driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert v4l2_clk to normal clk and enable the clock.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert ov2640 to a standard subdev driver. The soc-camera driver no longer
uses this driver, so it can safely be converted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is a bit confusing how CEC_CAP_RC and IS_REACHABLE(CONFIG_RC_CORE)
interact. By stripping CEC_CAP_RC at the beginning rather than after #else
it should be a bit clearer what is going on.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently when the RC Core is enabled (reachable) core code located
in cec_register_adapter() attempts to populate the RC structure with
a pointer to the 'parent' passed in by the caller.
Unfortunately if the caller did not specify RC capability when calling
cec_allocate_adapter(), then there will be no RC structure to populate.
This causes a "NULL pointer dereference" error.
Fixes: f51e80804f ("[media] cec: pass parent device in register(), not allocate()")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Update the bindings documenting the new hdmi phandle and
update exynos4.dtsi accordingly.
Tested with my Odroid U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
CC: linux-samsung-soc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Support the CEC notifier framework, simplifying drivers that
depend on this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for CEC notifiers, which is used to convey CEC physical address
information from video drivers to their CEC counterpart driver(s).
Based on an earlier version from Russell King:
https://patchwork.kernel.org/patch/9277043/
The cec_notifier is a reference counted object containing the CEC physical address
state of a video device.
When a new notifier is registered the current state will be reported to
that notifier at registration time.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The DRM object does not register the pipe with the WPF object. This is
used internally throughout the driver as a means of accessing the pipe.
As such this breaks operations which require access to the pipe from WPF
interrupts.
Register the pipe inside the WPF object after it has been declared as
the output.
Fixes: ff7e97c94d ("[media] v4l: vsp1: Store pipeline pointer in rwpf")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The struct vsp1_drm references a member 'planes' which doesn't exist.
Correctly identify this documentation against the 'inputs'
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While all VSP instances can process HSV internally, on Gen3 hardware
reading or writing HSV24 or HSV32 from/to memory causes the device to
hang. Disable those pixel formats on Gen3 hardware.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix all multi-line comments to comply with the kernel coding style.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The pipe->dl is used only inside vsp1_du_atomic_flush(), and can be
obtained and stored locally to simplify the code.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With multiple inputs through the BRU it is feasible for the streams to
race each other at stream-on.
Multiple VIDIOC_STREAMON calls racing each other could have process
N-1 skipping over the pipeline setup section and then start the pipeline
early, if videobuf2 has already enqueued buffers to the driver for
process N but not called the .start_streaming() operation yet
In the case of the video pipelines, this
can present two serious issues.
1) A null-dereference if the pipe->dl is committed at the same time as
the vsp1_video_setup_pipeline() is processing
2) A hardware hang, where a display list is committed without having
called vsp1_video_setup_pipeline() first
Repair this issue, by ensuring that only the stream which configures the
pipeline is able to start it.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The RPF and WPF U/V order bits have no effect for 3-planar formats on
Gen3 hardware. Swap the U and V planes addresses manually instead in
that case.
Fixes: b915bd24a0 ("[media] v4l: vsp1: Add tri-planar memory formats support")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_fh_init is already done. So call the v4l2_fh_exit in error
condition before returing from the function.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Minor tweaks to document the swap register and make the documentation
match the struct ordering
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The colorspace is independent of whether YUV or RGB is sent to the SoC.
Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move this out of the soc_camera directory into the atmel directory
where it belongs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch converts the atmel-isi driver from a soc-camera driver to a driver
that is stand-alone.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add DT support. Use it to get the reset and pwdn pins (if there are any).
Tested with one sensor requiring reset/pwdn and one sensor that doesn't
have reset/pwdn pins.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Get the clock for this sensor.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop unnecesary memset. Drop the unnecessary extendedmode check and
set the V4L2_CAP_TIMEPERFRAME capability.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add v4l2-async support for this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for Intel SR300 depth camera in uvc driver.
This includes adding three uvc GUIDs for the required pixel formats
and updating the uvc driver GUID-to-4cc tables with the new formats.
Signed-off-by: Daniel Patrick Johnson <teknotus@teknot.us>
Signed-off-by: Aviv Greenberg <avivgr@gmail.com>
Signed-off-by: Evgeni Raikhel <evgeni.raikhel@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide the frame structure and data layout of V4L2-PIX-FMT-INZI
format utilized by Intel SR300 Depth camera.
Signed-off-by: Evgeni Raikhel <evgeni.raikhel@intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The statistics function subtracts two timespecs manually. A helper is
provided by the kernel to do this.
Replace the implementation, using the helper.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The frame counters are inadvertently counting packets with content as
empty.
Fix it by correcting the logic expression
Fixes: 7bc5edb00b [media] uvcvideo: Extract video stream statistics
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All control menus use the english capitalization rules of titles.
The only menu not following these rules is the RGB Quantization Range control
menu. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to release the snd_card also on a late allocation error.
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 2a9f8b5d25 ("V4L/DVB (5206): Usbvision: set alternate interface
modification")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Cc: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c4018fa2e4 ("[media] dib0700: fix RC support on Hauppauge
Nova-TD")
Cc: stable <stable@vger.kernel.org> # 3.16
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most ioctls do not have to write back the contents of the argument
if an error is returned. But VIDIOC_S_EDID is an exception together
with the EXT_CTRLS ioctls (already handled correctly).
Add this exception to v4l2-compat-ioctl32.
This fixes a compliance error when using compat32 and trying to
set a new EDID with more blocks than the hardware supports. In
that case the driver will return -E2BIG and set edid.blocks to the
actual maximum number of blocks. This field was never copied back
to userspace due to this bug.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When CONFIG_PM is disabled, we get a couple of unused functions:
drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:927:13: error: 'mtk_jpeg_clk_off' defined but not used [-Werror=unused-function]
static void mtk_jpeg_clk_off(struct mtk_jpeg_dev *jpeg)
^~~~~~~~~~~~~~~~
drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:916:13: error: 'mtk_jpeg_clk_on' defined but not used [-Werror=unused-function]
static void mtk_jpeg_clk_on(struct mtk_jpeg_dev *jpeg)
Rather than adding more error-prone #ifdefs around those, this patch
removes the existing #ifdef checks and marks the PM functions as __maybe_unused
to let gcc do the right thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rick Chang <rick.chang@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the surrounding goto, it is likely that 'unprep_clk_gate'
was expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Further investigation revealed that codec buffers also don't need to
be allocated at higher addresses than firmware base for MFC v6+ hardware.
Those buffers can be quite large and its size depends on the selected
format and framesize. This patch changes the way the codec buffers are
allocated - driver will use generic allocator for them instead of the
pre-allocated buffer for firmware and contexts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Clock should be turned off after calling s5p_mfc_init_hw() from the
watchdog worker, like it is already done in the s5p_mfc_open() which also
calls this function.
Fixes: af93574678 ("[media] MFC: Add MFC 5.1 V4L2 driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Documentation for MFC hardware still uses 'left' and 'right' names for
the memory channel/banks, so replace BANK1/2 defines with more appropriate
BANK_L/R names.
Suggested-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It turned out that all versions of MFC v6+ hardware doesn't have a strict
requirement for ALL buffers to be allocated on higher addresses than the
firmware base like it was documented for MFC v5. This requirement is true
only for the device and per-context buffers. All video data buffers can be
allocated anywhere for all MFC v6+ versions. Basing on this fact, the
special DMA configuration based on two reserved memory regions is not
really needed for MFC v6+ devices, because the memory requirements for the
firmware, device and per-context buffers can be fulfilled by the simple
probe-time pre-allocated block allocator introduced in previous patch.
This patch enables support for such pre-allocated block based allocator
always for MFC v6+ devices. Due to the limitations of the memory management
subsystem the largest supported size of the pre-allocated buffer when no
CMA (Contiguous Memory Allocator) is enabled is 4 MiB.
This patch also removes the requirement to provide two reserved memory
regions for MFC v6+ devices in device tree. Now the driver is fully
functional without them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The main reason for using special configuration of IOMMU domain was the
problem with MFC firmware, which failed to operate properly when placed
at 0 DMA address. Instead of adding custom code for configuring each
variant of IOMMU domain and architecture specific glue code, simply use
what arch code provides and if the DMA base address equals zero, skip
first 128 KiB to keep required alignment. This patch also make the driver
operational on ARM64 architecture, because it no longer depends on ARM
specific DMA-mapping and IOMMU glue code functions.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Current MFC driver depends on the fact that when IOMMU is available, the
DMA-mapping framework and its IOMMU glue will use first-fit allocator.
This was true for ARM architecture, but its not for ARM64 arch. However, in
case of MFC v6+ hardware and latest firmware, it turned out that there is
no strict requirement for ALL buffers to be allocated on higher addresses
than the firmware base. This requirement is true only for the device and
per-context buffers. All video data buffers can be allocated anywhere for
all MFC v6+ versions.
Such relaxed requirements for the memory buffers can be easily fulfilled
by allocating firmware, device and per-context buffers from the probe-time
preallocated larger buffer. This patch adds support for it. This way the
driver finally works fine on ARM64 architecture. The size of the
preallocated buffer is 8 MiB, what is enough for three instances H264
decoders or encoders (other codecs have smaller memory requirements).
If one needs more for particular use case, one can use "mem" module
parameter to force larger (or smaller) buffer (for example by adding
"s5p_mfc.mem=16M" to kernel command line).
[mchehab@s-opensource.com: fix two checkpatch warnings: don't initialize
static to NULL; don't use S_foo permisions]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move code for DMA memory configuration with IOMMU into separate function
to make it easier to compare what is being done in each case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Firmware for MFC v6+ variants is not larger than 400 KiB, so there is no
need to allocate a full 1 MiB buffer for it. Reduce it to 512 KiB to keep
proper alignment of allocated buffer.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Once firmware buffer has been converted to use s5p_mfc_priv_buf structure,
it is possible to allocate it with existing s5p_mfc_alloc_priv_buf()
function. This change will help to reduce code variants in the next
patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To complete DMA memory configuration for MFC device, allocation of the
firmware buffer is needed, because some parameters are dependant on its base
address. Till now, this has been handled in the s5p_mfc_alloc_firmware()
function. This patch moves that logic to s5p_mfc_configure_dma_memory() to
keep DMA memory related operations in a single place. This way
s5p_mfc_alloc_firmware() is simplified and does what it name says. The
other consequence of this change is moving s5p_mfc_alloc_firmware() call
from the s5p_mfc_probe() function to the s5p_mfc_configure_dma_memory().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use s5p_mfc_priv_buf structure for keeping the firmware image. This will
help handling of firmware buffer allocation in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Setting DMA max segment size to 32 bit mask is a part of DMA memory
configuration, so move those calls to s5p_mfc_configure_dma_memory()
function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change parameters for s5p_mfc_alloc_priv_buf() and s5p_mfc_release_priv_buf()
functions. Instead of DMA device pointer and a base, provide common MFC
device structure and memory bank context identifier.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Internal MFC driver device structure contains two entries for keeping
addresses of the DMA memory banks. Replace them with the dma_base[] array
and use defines for accessing particular banks. This will help to simplify
code in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Internal MFC driver device structure contains two pointers to devices used
for DMA memory allocation: mem_dev_l and mem_dev_r. Replace them with the
mem_dev[] array and use defines for accessing particular banks. This will
help to simplify code in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unused structures, definitions and functions
that are no longer called from the driver code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Reviewed-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Interrupt routine must wake process waiting for given interrupt AFTER
updating driver's internal structures and contexts. Doing it in-between
is a serious bug. This patch moves all calls to the wake() function to
the end of the interrupt processing block to avoid potential and real
races, especially on multi-core platforms. This also fixes following issue
reported from clock core (clocks were disabled in interrupt after being
unprepared from the other place in the driver, the stack trace however
points to the different place than s5p_mfc driver because of the race):
WARNING: CPU: 1 PID: 18 at drivers/clk/clk.c:544 clk_core_unprepare+0xc8/0x108
Modules linked in:
CPU: 1 PID: 18 Comm: kworker/1:0 Not tainted 4.10.0-next-20170223-00070-g04e18bc99ab9-dirty #2154
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: pm pm_runtime_work
[<c010d8b0>] (unwind_backtrace) from [<c010a534>] (show_stack+0x10/0x14)
[<c010a534>] (show_stack) from [<c033292c>] (dump_stack+0x74/0x94)
[<c033292c>] (dump_stack) from [<c011cef4>] (__warn+0xd4/0x100)
[<c011cef4>] (__warn) from [<c011cf40>] (warn_slowpath_null+0x20/0x28)
[<c011cf40>] (warn_slowpath_null) from [<c0387a84>] (clk_core_unprepare+0xc8/0x108)
[<c0387a84>] (clk_core_unprepare) from [<c0389d84>] (clk_unprepare+0x24/0x2c)
[<c0389d84>] (clk_unprepare) from [<c03d4660>] (exynos_sysmmu_suspend+0x48/0x60)
[<c03d4660>] (exynos_sysmmu_suspend) from [<c042b9b0>] (pm_generic_runtime_suspend+0x2c/0x38)
[<c042b9b0>] (pm_generic_runtime_suspend) from [<c0437580>] (genpd_runtime_suspend+0x94/0x220)
[<c0437580>] (genpd_runtime_suspend) from [<c042e240>] (__rpm_callback+0x134/0x208)
[<c042e240>] (__rpm_callback) from [<c042e334>] (rpm_callback+0x20/0x80)
[<c042e334>] (rpm_callback) from [<c042d3b8>] (rpm_suspend+0xdc/0x458)
[<c042d3b8>] (rpm_suspend) from [<c042ea24>] (pm_runtime_work+0x80/0x90)
[<c042ea24>] (pm_runtime_work) from [<c01322c4>] (process_one_work+0x120/0x318)
[<c01322c4>] (process_one_work) from [<c0132520>] (worker_thread+0x2c/0x4ac)
[<c0132520>] (worker_thread) from [<c0137ab0>] (kthread+0xfc/0x134)
[<c0137ab0>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
---[ end trace 1ead49a7bb83f0d8 ]---
Fixes: af93574678 ("[media] MFC: Add MFC 5.1 V4L2 driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: stable@vger.kernel.org # v4.5+
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix s5p_mfc_set_dec_frame_buffer_v6() to print buffer pointer in hex
to be consistent with the rest of the messages in the routine.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Initialize members of the internal device and context structures as early
as possible to avoid access to uninitialized objects on initialization
failures. If loading firmware or creating of the hardware instance fails,
driver will access device or context queue in error handling path, which
might not be initialized yet, what causes kernel panic. Fix this by moving
initialization of all static members as early as possible.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Changeset 1f862a68df ("[media] dvb_frontend: move kref to struct
dvb_frontend") added a kref to the struct dvb_frontend, but it
didn't document it.
Fixes: 1f862a68df ("[media] dvb_frontend: move kref to struct dvb_frontend")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use refcount_t to manage the refcount to the memory type specific buffer
videobuf2 buffer implementations. refcount_t is better suitable for the
purpose than atomic_t.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
refcount_t is better suitable for counting references than atomic_t.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VIDIOC_G_EDID implementation in vivid didn't take edid->start_block into account when
copying the EDID data.
Make sure that the internal EDID is updated with the correct CEC physical address. Currently
the returned EDID is updated, but that will only work well if edid->start_block is 0.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use for_each_sg() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The check for ret being non-zero is false as ret is always
zero, hence we have redundant dead code that can be removed.
Detected with CoverityScan, CID#112968 ("Constant' variable guards
dead code (DEADCODE)'")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The extra pairs of parentheses are not needed and cause clang
warnings like this:
drivers/media/platform/mtk-vcodec/venc/venc_vp8_if.c:158:32: error: equality comparison with extraneous parentheses [-Werror,-Wparentheses-equality]
if ((inst->work_bufs[i].size == 0))
~~~~~~~~~~~~~~~~~~~~~~~~^~~~
drivers/media/platform/mtk-vcodec/venc/venc_vp8_if.c:158:32: note: remove extraneous parentheses around the comparison to silence this warning
if ((inst->work_bufs[i].size == 0))
~ ^ ~
drivers/media/platform/mtk-vcodec/venc/venc_vp8_if.c:158:32: note: use '=' to turn this equality comparison into an assignment
if ((inst->work_bufs[i].size == 0))
^~
=
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The symptom is continuous log "mtk-jpeg 18004000.jpegdec: Context is NULL"
in kernel log. It is because the error handling in irq doesn't clear
interrupt.
The calling flow like as below when issue happen
mtk_jpeg_device_run()
mtk_jpeg_job_abort()
v4l2_m2m_job_finish() -> m2m_dev->curr_ctx = NULL;
mtk_jpeg_dec_irq()
v4l2_m2m_get_curr_priv()
-> m2m_dev->curr_ctx == NULL
-> return NULL
log "Context is NULL"
There is race condition between job_abort() and irq. In order to simplify
code, don't want to add extra flag to maintain state, empty job_abort() and
clear interrupt before v4l2_m2m_get_curr_priv() in irq.
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Acked-by: Rick Chang <rick.chang@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check the number of endpoints to avoid accessing memory
beyond the endpoint array should a device lack the expected endpoints.
Note that, as far as I can tell, the gspca framework has already made
sure there is at least one endpoint in the current alternate setting so
there should be no risk for a NULL-pointer dereference here.
Fixes: b517af7228 ("V4L/DVB: gspca_konica: New gspca subdriver for
konica chipset using cams")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The are only HIST_ENTRIES worth of entries in hist_entry however the
for-loop is iterating one too many times leasing to a read access off
the end off the array ctrls->hist_entry. Fix this by iterating by
the correct number of times.
Detected by CoverityScan, CID#1415279 ("Out-of-bounds read")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY4ZYkAAoJEHm+PkMAQRiGsq4H/R4PMXDoe2XhSSk7IoT97pXV
/A8np/scAPjzEgYUidbb54OSqWwsPRuPGWONTFeSrE2u0L4wln/REI91jg7QetLq
IisncExlYeJ/XQ+iO0ZZh9fLbqwIlEJFdSXmyIFr3m/TBxe8a61C8j93oNgM1tHT
yuwzlq7c3sLq2hsmUG2HyL2kJsEfRasv4Rk0yhFuti12zVsBoTW4qmZuMauq+gdf
f7cSYgiHhPTdb2o+azg5O7uYNHaQQBxdUMlIuhhYtVOUq+pFDO23SLHSFIW2NwOm
Zn5R6CFSrLsCw0Bx0v8Xlc151QUbaRK4h9lhUhkBr6d3uNShU1NQ9JojpSvYwBo=
=vP6E
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rc5' into patchwork
Linux 4.11-rc5
* tag 'v4.11-rc5': (1168 commits)
Linux 4.11-rc5
tty: pl011: fix earlycon work-around for QDF2400 erratum 44
kasan: do not sanitize kexec purgatory
drivers/rapidio/devices/tsi721.c: make module parameter variable name unique
mm/hugetlb.c: don't call region_abort if region_chg fails
kasan: report only the first error by default
hugetlbfs: initialize shared policy as part of inode allocation
mm: fix section name for .data..ro_after_init
mm, hugetlb: use pte_present() instead of pmd_present() in follow_huge_pmd()
mm: workingset: fix premature shadow node shrinking with cgroups
mm: rmap: fix huge file mmap accounting in the memcg stats
mm: move mm_percpu_wq initialization earlier
mm: migrate: fix remove_migration_pte() for ksm pages
nfs: flexfiles: fix kernel OOPS if MDS returns unsupported DS type
NFSv4.1 fix infinite loop on IO BAD_STATEID error
serial: 8250_EXAR: fix duplicate Kconfig text and add missing help text
tty/serial: atmel: fix TX path in atmel_console_write()
tty/serial: atmel: fix race condition (TX+DMA)
serial: mxs-auart: Fix baudrate calculation
irqchip/mips-gic: Fix Local compare interrupt
...
-----BEGIN PGP SIGNATURE-----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=xT1A
-----END PGP SIGNATURE-----
Merge tag 'media/v4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- dvb-usb-firmware: don't do DMA on stack
- coda/imx-vdoa: platform_driver should not be const
- bdisp: Clean up file handle in open() error path
- exynos-gsc: Do not swap cb/cr for semi planar formats
* tag 'media/v4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] exynos-gsc: Do not swap cb/cr for semi planar formats
[media] bdisp: Clean up file handle in open() error path
[media] coda/imx-vdoa: platform_driver should not be const
[media] dvb-usb-firmware: don't do DMA on stack
This patch fix some spelling typos found in printk.
[jkosina@suse.cz: drop arch/arm64/kernel/hibernate.c that was already
in place]
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from reset_control_get_optional and to call
reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check for the required out endpoint to avoid dereferencing
a NULL-pointer in mce_request_packet should a malicious device lack such
an endpoint. Note that this path is hit during probe.
Fixes: 66e89522af ("V4L/DVB: IR: add mceusb IR receiver driver")
Cc: stable <stable@vger.kernel.org> # 2.6.36
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If a lirc device is unplugged, the struct rc_dev is freed even though
userspace can still have a file descriptor open on the lirc chardev. The
rc_dev structure can be used in a subsequent, or even currently executing
ioctl, read or write.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This has been broken for a long time, so presumably it is not used. I
have no hardware to test this on.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=61401
Fixes: 90ab5ee ("module_param: make bool parameters really bool")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Split the protocol into two variants, one for keyboard and one for mouse
data.
Note that the mce_kbd protocol cannot be used on the igorplugusb, since
the IR is too long.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This feature was never set. The ioctl should fail if no resolution
is set.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The lirc keymap existed once upon a time to select the lirc protocol.
Since '275ddb4 [media] rc-core: remove the LIRC "protocol"', IR is
always passed to the lirc decoder so this keymap is no longer needed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the documentation, a timeout of 0 turns off timeouts,
which is not the case.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The drivers sets the hardware to idle when a timeout occurs. This can
be any reasonable value.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If timeouts or carrier range is not supported, return proper error.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We shouldn't be using ENOSYS when a feature is not available. I've tested
lirc; nothing is broken as far as I can make out.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adjust the keymap to use the correct nec scancodes, and adjust the
rc driver to output the correct nec scancodes.
Now the keymap can be used with any nec receiver, and the rc device
should work with any nec keymap.
Tested-by: Vincent McIntyre <vincent.mcintyre@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
update_subrect() adjusts the sub-rectangle to be inside a base area.
It checks width and height to not exceed those of the area, then it
checks the low border (left or top) to lie within the area, then the
high border (right or bottom) to lie there too. This latter check has
a bug, which is fixed by this patch.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[g.liakhovetski@gmx.de: dropped supposedly wrong hunks]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
After changes to v4l2_clk API introduced in v4.1 by commits a37462b919
'[media] V4L: remove clock name from v4l2_clk API' and 4f528afcfb
'[media] V4L: add CCF support to the v4l2_clk API', ov6650 sensor
stopped responding because v4l2_clk_get(), still called with
depreciated V4L2 clock name "mclk", started to return respective CCF
clock instead of the V4l2 one registered by soc_camera. Fix it by
calling v4l2_clk_get() with NULL clock name.
Created and tested on Amstrad Delta against Linux-4.7-rc3 with
omap1_camera fixes.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vpif display driver uses a static i2c adapter ID of 1 but on the
da850-evm board in DT boot mode the i2c adapter ID is actually 0.
Make the adapter ID configurable like it already is for vpif capture.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It's no longer necessary to keep the i2c_client in the device struct
unmodified until a sensor is found, so reduce stack usage in
em28xx_probe_sensor_micron() and em28xx_probe_sensor_omnivision() by using
a pointer to the client instead of a local copy.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:1296:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Rick Chang <rick.chang@mediatek.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All remaining soc-camera drivers use videobuf2, drop support for
videobuf1.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: also drop 'select VIDEOBUF_GEN' from Kconfig]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
VPU firmware has a bug and may return invalid buffer index for
some vp9 videos. Check the buffer indexes before accessing the
buffer.
Signed-off-by: Wu-Cheng Li <wuchengli@chromium.org>
Acked-by: Tiffany Lin <Tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Include <linux/slab.h> to fix these build errors:
../drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c: In function 'mtk_jpeg_open':
../drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:1017:2: error: implicit declaration of function 'kzalloc' [-Werror=implicit-function-declaration]
ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
../drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:1017:6: warning: assignment makes pointer from integer without a cast [enabled by default]
ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
../drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:1047:2: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
kfree(ctx);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ming Hsiu Tsai <minghsiu.tsai@mediatek.com>
Cc: Rick Chang <rick.chang@mediatek.com>
Cc: Bin Liu <bin.liu@mediatek.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously multiple calls to v4l2_device_register_subdev_nodes() ended up
corrupting memory and leaking some, too. This patch changes the behaviour so
that sub-devices the device nodes of which are already registered are
ignored.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Before this patch:
$ modinfo drivers/media/i2c/et8ek8/et8ek8.ko | grep alias
alias: i2c:et8ek8
After this patch:
$ modinfo drivers/media/i2c/et8ek8/et8ek8.ko | grep alias
alias: i2c:et8ek8
alias: of:N*T*Ctoshiba,et8ek8C*
alias: of:N*T*Ctoshiba,et8ek8
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Feature Abort shouldn't be sent in reply to messages from Unregistered,
since that would make it a broadcast message.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When validating the struct cec_s_log_addrs input a debug message is printed
for all except two of the 'return -EINVAL' paths.
Also log the reason for the missing two paths.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several error paths didn't log why an error was returned. Add this.
Also handle the corner case of "adapter is unconfigured AND the message
is from Unregistered to TV AND reply is non-zero" separately and return
EINVAL in that case, since it really is an invalid value and not an
unconfigured CEC device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The hardcoded function name is actually wrong. Use __func__ instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC_TRANSMIT ioctl now returns -EPERM if an attempt is made to
transmit a message for an unconfigured adapter (i.e. userspace
never called CEC_ADAP_S_LOG_ADDRS).
This differentiates this case from when LAs are configured, but no
physical address is set. In that case -ENONET is returned.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC specifications explicitly allows you to send poll messages and
Image/Text View On messages to a TV, even when unconfigured (i.e. there is
no hotplug signal detected). Some TVs will pull the HPD low when switching
to another input, or when going into standby, but CEC should still be
allowed to wake up such a display.
Add support for sending messages with initiator 0xf (Unregistered) and
destination 0 (TV) when no physical address is present.
This also required another change: the CEC adapter has to stay enabled as
long as 1) the CEC device is configured or 2) at least one filehandle is open
for the CEC device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the adapter is unloaded or unconfigured, then all transmits and
pending waits should be flushed.
Move this code into its own function and improve the code that cancels
delayed work to avoid having to unlock adap->lock.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
vivid_try_fmt_vid_cap() called tpg_calc_line_width to calculate the sizeimage
value, but that tpg function uses the current format, not the proposed (tried)
format.
Rewrote this code to calculate this correctly.
The vivid_try_fmt_vid_out() code was completely wrong w.r.t. sizeimage, and
neither did it take the vdownsampling[] factors into account.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
