When a YCBCR format is selected, we can merely copy the colorimetry
information directly as we use the same definitions for both the
unpacked AVI info frame and the hdmi_data_info structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up hdmi_set_clk_regenerator() by allowing it to take the audio
sample rate and ratio directly, rather than hiding it inside the
function. Raise the unsupported pixel clock/sample rate message from
debug to error level as this results in audio not working correctly.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy configuration is dependent on the SoC, and we look up values for
some of the registers in SoC specific data. However, we had partially
programmed the phy before we had successfully looked up the clock rate.
Also, we were only checking that we had a valid configuration for the
currctrl register.
Move all these lookups to the start of this function instead, so we can
check that all lookups were successful before beginning to program the
phy.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy comments in dw_hdmi.c applied to the iMX6 version. Move these
comments to the iMX6 dw_hdmi-imx data along side the data.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This set of patches adjust the setup of the HDMI CTS/N values for audio
support to be compliant with the work-around given in the iMX6 errata
documentation as part of the preparation for integrating audio support
for this driver, and also update the HDMI phy configuration for Rockchip
devices to improve the HDMI eye pattern.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: rockchip/dw_hdmi-rockchip: improve for HDMI electrical test
drm: bridge/dw_hdmi: separate VLEVCTRL settting into platform driver
drm: bridge/dw_hdmi: fixed codec style
drm: bridge/dw_hdmi: adjust n/cts setting order
drm: bridge/dw_hdmi: protect n/cts setting with a mutex
drm: bridge/dw_hdmi: combine hdmi_set_clock_regenerator_n() and hdmi_regenerate_cts()
Conflicts:
drivers/gpu/drm/imx/dw_hdmi-imx.c
Because of iMX6 & Rockchip have differnet mpll config parameter,
the VLEVCTRL parameter would be different. In this case we should
separate VLEVCTRL setting from the common dw_hdmi driver, config
this parameter in platform driver(dw_hdmi-imx and dw_hdmi-rockchip)
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using a local struct pointer to reduce one level of indirection
makes the code slightly more readable.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch derived from one from Yakir Yang. Yakir Yang says:
For Designerware HDMI, the following write sequence is recommended:
1. aud_n3 (set bit ncts_atomic_write if desired)
2. aud_cts3 (set CTS_manual and CTS value if desired/enabled)
3. aud_cts2 (required in CTS_manual)
4. aud_cts1 (required in CTS_manual)
5. aud_n3 (bit ncts_atomic_write with same value as in step 1.)
6. aud_n2
7. aud_n1
However, avoid the ncts_atomic_write_bit and CTS_manual settings in this
patch, both of which are marked reserved in the iMX6 documentation. All
iMX6 code in the wild seems to want CTS_manual cleared.
Having requested clarification from FSL, it appears that neither of
these bits are implemented in their version of the IP.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The HDMI n/cts settings need to be updated whenever the audio sample
rate or the video pixel clock changes. This needs to be protected
against concurrency as there is no synchronisation between these two
operations. Introduce a mutex (called audio_mutex) to protect against
two threads trying to update the video clock rate and pixel clock
simultaneously.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Combine these two functions into a single implementation. These two
functions are called consecutively anyway. Idea from a patch by
Yakir Yang.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ps8622_attach and ps8522_driver symbols are never used outside this
file, so they should be static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit fbc4572e9c48e45b ("drm/bridge: make bridge registration independent of
drm flow") introduced some drm/bridge API modifications. Make the necessary
changes so that we can avoid the build breakage:
drivers/gpu/drm/bridge/dw_hdmi.c: In function 'dw_hdmi_bridge_destroy':
drivers/gpu/drm/bridge/dw_hdmi.c:1378:2: error: implicit declaration of function 'drm_bridge_cleanup' [-Werror=implicit-function-declaration]
drivers/gpu/drm/bridge/dw_hdmi.c: At top level:
drivers/gpu/drm/bridge/dw_hdmi.c:1471:2: error: unknown field 'destroy' specified in initializer
drivers/gpu/drm/bridge/dw_hdmi.c: In function 'dw_hdmi_register':
drivers/gpu/drm/bridge/dw_hdmi.c:1535:2: error: implicit declaration of function 'drm_bridge_init' [-Werror=implicit-function-declaration]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If devm_request_threaded_irq() fails we should jump to 'err_iahb' label that
will disable the clocks that were previously enabled.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Force bridge connector detection at the end of the bridge attach.
This is needed to detect the bridge connector early.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add drm_panel calls to the driver to make the panel and
bridge work together in tandem.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently, third party bridge drivers(ptn3460) are dependent
on the corresponding encoder driver init, since bridge driver
needs a drm_device pointer to finish drm initializations.
The encoder driver passes the drm_device pointer to the
bridge driver. Because of this dependency, third party drivers
like ptn3460 doesn't adhere to the driver model.
In this patch, we reframe the bridge registration framework
so that bridge initialization is split into 2 steps, and
bridge registration happens independent of drm flow:
--Step 1: gather all the bridge settings independent of drm and
add the bridge onto a global list of bridges.
--Step 2: when the encoder driver is probed, call drm_bridge_attach
for the corresponding bridge so that the bridge receives
drm_device pointer and continues with connector and other
drm initializations.
The old set of bridge helpers are removed, and a set of new helpers
are added to accomplish the 2 step initialization.
The bridge devices register themselves onto global list of bridges
when they get probed by calling "drm_bridge_add".
The parent encoder driver waits till the bridge is available
in the lookup table(by calling "of_drm_find_bridge") and then
continues with its initialization.
The encoder driver should also call "drm_bridge_attach" to pass
on the drm_device to the bridge object.
drm_bridge_attach inturn calls "bridge->funcs->attach" so that
bridge can continue with drm related initializations.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Assign the pointer to bridge ops structure(drm_bridge_funcs) in
the bridge driver itself, instead of passing it to drm_bridge_init.
This will allow bridge driver developer to pack bridge private
information inside the bridge object and pass only the drm-relevant
information to drm_bridge_init.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch does the following changes:
-- Use usleep_range instead of udelay.
-- Remove driver_private member from ptn3460 structure.
-- Make all possible functions and structures static.
-- Use dev_err for non-DRM errors.
-- Arrange header files alphabetically.
-- s/edid/EDID in all error messages.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The encoder ->prepare() and ->mode_set() methods need to use the
hw adjusted mode, not the original mode.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Otherwise a spurious interrupt might trigger (and crash) the interrupt handler
before probing finished.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Rockchip RK3288 hdmi is compatible with dw_hdmi
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
RK3288 HDMI will not work without the spare bit of
HDMI_PHY_CONF0 enable
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
HDMI_IH_I2CMPHY_STAT0 is a clear on write register, which indicates i2cm
operation status(i2c transfer done or error), every hdmi phy register
configuration must check this register to make sure the configuration
has complete. But the indication bit should be cleared after check, otherwise
the corresponding bit will hold on forever, this may give a wrong signal for
next check.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
some platform may not support all the display mode,
add mode_valid interface check it
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
On rockchip rk3288, only word(32-bit) accesses are
permitted for hdmi registers. Byte width accesses (writeb,
readb) generate an imprecise external abort.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
the original imx hdmi driver is under drm/imx/,
which depends on imx-drm, so move the imx hdmi
driver out to drm/bridge and rename it to dw_hdmi
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many drm connectors do not need mode validation.
The patch makes this callback optional and removes dumb implementations.
v2: Rebase:
- imx move to a shared (but still dummy) ->mode_valid implementation.
- probe helpers have been extracted to drm_probe_helper.c
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch exports ptn3460_init function so that other modules
can call this function.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The recently added PTN3460 device driver uses interfaces that
are provided by the KMS helper infrastructure, so we should
explicitly select that to avoid this linker error:
ERROR: "drm_helper_probe_single_connector_modes" [drivers/gpu/drm/bridge/ptn3460.ko] undefined!
ERROR: "drm_helper_connector_dpms" [drivers/gpu/drm/bridge/ptn3460.ko] undefined!
We have to drop the I2C dependency to avoid a circular dependency
chain, but that's ok because DRM already selects I2C.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds a drm_bridge driver for the PTN3460 DisplayPort to LVDS
bridge chip.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
