Support new version of beacon template command which deprecates
the use of the tx command inside.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When resuming, it's possible for the following scenario to occur:
* iwl_pci_resume() enables the RF-kill interrupt
* iwl_pci_resume() reads the RF-kill state (e.g. to 'radio enabled')
* RF_KILL interrupt triggers, and iwl_pcie_irq_handler() reads the
state, now 'radio disabled', and acquires the &trans_pcie->mutex.
* iwl_pcie_irq_handler() further calls iwl_trans_pcie_rf_kill() to
indicate to the higher layers that the radio is now disabled (and
stops the device while at it)
* iwl_pcie_irq_handler() drops the mutex
* iwl_pci_resume() continues, acquires the mutex and calls the higher
layers to indicate that the radio is enabled.
At this point, the device is stopped but the higher layers think it's
available, and can call deeply into the driver to try to enable it.
However, this will fail since the device is actually disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support differentiating between two phys for a000 devices
in order to load the correct firmware.
Eventually when moving completely to the new phy we will be
able to remove this.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_drv structure contains trans which already contains cfg, so
storing cfg separately in iwl_drv is redundant. Remove it and access
trans->cfg instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When iwl_drv_start() is called, trans->cfg must already be set, so
there's no need to pass cfg separately, since it can be accessed
directly from trans->cfg.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a small frame is copied completely into the skb->head, the code
doesn't take alignment into account, making mac80211 copy it again
later on architectures that need the alignment. Avoid this by taking
the PAD flag from the device into account when copying.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our 9000 device supports 64 bit DMA address for RX only, and
not for TX.
Setting DMA mask to 64 for the whole device is erroneous - we
can do it only for a000 devices where device is capable of
both RX & TX DMA with 64 bit address space.
Fixes: 96a6497bc3 ("iwlwifi: pcie: add 9000 series multi queue rx DMA support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.
This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the tx_cmd length in the mvm code, which is
complicated by the fact that DQA may want to temporarily store
the SKB on the side, adjust the length in the PCIe code which
also knows about this since it's responsible for duplicating
all those headers that are account for in this code.
As the PCIe code already relies on the tx_cmd->len field, this
doesn't really introduce any new dependencies.
To make this possible we need to move the memcpy() of the TX
command until after it was updated.
This does even simplify the code though, since the PCIe code
already does a lot of manipulations to build A-MSDUs correctly
and changing the length becomes a simple operation to see how
much was added/removed, rather than predicting it.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't really need clear the skb's status area nor store the
dev_cmd into it until we really commit to the frame by handing
it to the transport - defer those operations until just before
we do that.
This doesn't entirely fix the bug with frames not getting sent
out after having been deferred due to DQA, because it doesn't
restore the info->driver_data[0] place that was already set to
zero (or another value) by the A-MSDU logic.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware will soon actually look at the AID field, and
when it does that it'll try to ensure that the AID is never
changing. Due to the way the station is added, it may start
with an invalid AID before it's associated, so to ensure a
constant AID (once it becomes non-zero), track the station
state and set the AID only when the station is associated
and when it disassociates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a long-standing bug that was introduced when this code
was introduced: cfg80211 passes a pointer, but we treat it as if
it was passing a value. The result is that we pass the pointer to
the firmware, instead of the value. It's not clear how this could
ever have worked, unless the firmware is ignoring this value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When driver needs to access the contents of a streaming DMA buffer
without unmapping it it should call dma_sync_single_for_cpu().
Once the call has been made, the CPU "owns" the DMA buffer and can
work with it as needed.
Before the device accesses the buffer, however, ownership should be
transferred back to it with dma_sync_single_for_device().
Both calls weren't performed by the driver, resulting with odd paging
errors on some platforms. Fix it.
Fixes: a6c4fb4441 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support getting alive from two LMACs and dumping debug
data from both.
Deprecate older alive notifications no one is using.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's already a variable with the result in scope, use that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If iwl_mvm_find_free_queue() doesn't find a free queue, it will
return an inactive one.
However, not all the call paths free this queue before reassigning
it, which is a bug.
Check it in other paths and act accordingly.
Fixes: 9794c64f30 ("iwlwifi: mvm: support dqa queue inactivation upon timeout")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For CDB devices we will want to configure scan parameters
per band.
Support the new scan API for now. Logic per band will be
added in the future.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For CDB arch there is another auxiliary mac.
Support statistics APIs that were changed to reflect that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we have up to 3 phy contexts - defined by NUM_PHY_CTX.
However - some code paths validate the ID by using MAX_PHYS define
which is set to 4.
While there is no harm it is incorrect - since the maximum is 3.
Remove the define and use the correct one.
Cleanup the code a bit while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since offchannel activity doesn't always require a BSS, e.g. ANQP
sessions, offchannel frames should not use the BSS queue, because it
might not be initialized.
Use the auxilary queue instead
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add to the v1 of the mfuart loading notification, the size
of the mfuart image, and write it to dmesg once the notification
is received.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 devices the INIT and RT images are unified to one
image.
The changes in the flow are the following:
* Driver load only RT firmware - meaning that the nvm access
command will be done in the RT image load flow.
* A new command (NVM_ACCESS_COMPLETE) now signals to the FW that
the driver is done accessing the NVM and FW can proceed with phy
calibrations.
* Phy DB is no longer sent from INIT FW to be restored by driver
for the RT FW - all the phy DB is now internal to the FW.
INIT complete will now follow the NVM access command, without
phy DB calls before.
* Paging command is sent earlier in the flow before NVM access
to enable a complete load of FW.
* caution must be care when restart is called since we may have
not completed init flow even though we are in RT firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We added the uAPSD enabled ACs and that made the
firmware choose to pull frames with uAPSD trigger
frames instead of PS-Poll.
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For old firmwares the memory wasn't allocated, resulting in panic.
Make it dynamically allocated as well. Allow any order of functions
call.
Fixes: eef187a7b8 ("iwlwifi: enlarge number of ucode sections")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tested-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This set of station id is redundant - it is being initialised
above.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When removing inactive queue - use the central disable queue
function. This is needed due to a000 changes to come, but is
a proper cleanup anyway.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value returned from iwl_mvm_send_cmd_pdu() in this function is not
used and always returns an error (which is the whole point of the
call). Tag the ret variable with __maybe_unused to avoid this compile
warning when W=1 is used:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/debugfs.c: In function ‘iwl_dbgfs_fw_restart_write’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/debugfs.c:875:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When compiling with W=1, we get the following warning in debugfs.c:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/debugfs.c: In function ‘iwl_dbgfs_fw_restart_write’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/debugfs.c:2313:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret;
^
Fix it by ignoring the return value in this case.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the sta_id variable, to avoid this compile warning when
compiling with W=1:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/sta.c: In function ‘iwl_mvm_change_queue_owner’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/sta.c:871:5: warning: variable ‘sta_id’ set but not used [-Wunused-but-set-variable]
s8 sta_id;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The return value from this function is never used, so make it return
void to avoid getting the following warning when compiling wiht W=1:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/rs.c: In function ‘rs_tl_turn_on_agg_for_tid’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/rs.c:400:6: warning: variable ‘load’ set but not used [-Wunused-but-set-variable]
u32 load;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
shift_param is defined and set in iwl_pcie_load_cpu_sections but not
used. Fix this to avoid -Wunused-but-set-variable warning.
The code using it turned into dead code with commit dcab8ecd56
("iwlwifi: mvm: support ucode load for family_8000 B0 only") which
added a separate function iwl_pcie_load_given_ucode_8000 (then 8000b)
for IWL_DEVICE_FAMILY_8000. Commit 76f8c0e17e ("iwlwifi: pcie:
remove dead code") removed the dead code but left shift_param as is.
iwlwifi/pcie/trans.c: In function ‘iwl_pcie_load_cpu_sections’:
iwlwifi/pcie/trans.c:871:6: warning: variable ‘shift_param’ set but not used [-Wunused-but-set-variable]
Fixes: dcab8ecd56 ("iwlwifi: mvm: support ucode load for family_8000 B0 only")
Fixes: 76f8c0e17e ("iwlwifi: pcie: remove dead code")
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Liad Kaufman <liad.kaufman@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[removed some unnecessary braces]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Commit 5fc0f76c4 introduced Rx stats from debugfs, the function
iwl_mvm_reset_frame_stats from that commit defines and sets mcs but
does not use it. Compiling iwlwifi with W=1 gives this warning -
iwlwifi/mvm/rs.c: In function ‘iwl_mvm_update_frame_stats’:
iwlwifi/mvm/rs.c:3074:14: warning: variable ‘mcs’ set but not used [-Wunused-but-set-variable]
Fixes: 5fc0f76c43 (iwlwifi: mvm: add Rx frames statistics via debugfs)
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mvmvif is defined and set in rs_mimo_allow but not used. Compiling
iwlwifi with W=1 gives the following warning, remove it. mvmsta is
used only to obtain mvmvif so remove it as well.
iwlwifi/mvm/rs.c: In function 'rs_mimo_allow':
iwlwifi/mvm/rs.c:165:22: warning: variable 'mvmvif' set but not used.[-Wunused-but-set-variable]
This fix removes calls to iwl_mvm_sta_from_mac &
iwl_mvm_vif_from_mac. They are both accessors, and do not have any
side-effects. Commit e621c2282e ("iwlwifi: rs: Remove workaround
that disables MIMO on P2P") removed a workaround that disabled MIMO on
P2P, 'mvmvif' was used for that workaround, but not removed with it.
Fixes: e621c2282e ("iwlwifi: rs: Remove workaround that disables MIMO on P2P")
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Emmanuel Grumbach <emmmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The temperature variable is set but not used in
iwl_mvm_handle_statistics(). Remove it to avoid the following
compiler warning when W=1 is used:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/rx.c: In function ‘iwl_mvm_handle_rx_statistics’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/rx.c:759:6: warning: variable ‘temperature’ set but not used [-Wunused-but-set-variable]
u32 temperature;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
IWL6000G2B_UCODE_API_MAX is not defined. ucode_api_max of
IWL_DEVICE_6030 uses IWL6000G2_UCODE_API_MAX. Use this also for
MODULE_FIRMWARE.
Fixes: 9d9b21d1b6 ("iwlwifi: remove IWL_*_UCODE_API_OK")
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For 9000 devices withg upload, FW cannot send the entire phy
flags, and will send only the band - which is what we really
care about anyway. Change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In preparation for the new TX cmd - move the rate calculation
to a diffrent function, and make it independent of the TX
command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the function changes the TX cmd itself.
Make it more generic by returning a value, as preperation
to the new TX cmd.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The maximum number of firmware sections is now 32 instead of 16 for
a000 devices. Set the appropriate define. Avoid out of bounds access
in case there are more sections than the maximum set by driver.
Make the driver extensible to FW size changes by allocating the
section memory dynamically.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The logic in the paging calculations is a bit hard to
follow. Replace it with a kernel define.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some of the code there is duplicate while the only change is
the block size. Unifying it shortens the code and make the
difference clearer.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When copying from vmalloc'ed memory to the SG list, don't crash
if the transport didn't provide any data.
Fixes: 7e62a699aa ("iwlwifi: mvm: use dev_coredumpsg()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to some new features and changes, the firmware file will now
specify what type of memory to dump, in upper 8 bits of the type
field of the TLV. Parse it (types we don't understand are errors)
and teach the code to dump periphery memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The return value is never used, so make the function void.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no reason to be validating the memory dump types, or
checking them for duplication, or anything, since we really
just pass them through from the TLV to the dump.
Thus, change the way we handle memory dump TLVs to let the
driver just blindly use anything specified there, dumping it
into the memory dump output file.
This makes the system extensible without driver changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For unified images, we shouldn't restart the HW if suspend fails. The
only reason for restarting the HW with non-unified images is to go
back to the D0 image.
Fixes: 23ae61282b ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
