The OMAP port to the common clk framework[1] resulted in spurious WARNs
while disable unused clocks. This is due to _clkdm_clk_hwmod_disable
catching clkdm->usecount's with a value of zero. Even less desirable it
would not allow the clkdm_clk_disable function pointer to get called due
to an early return of -ERANGE.
This patch adds a check for such a corner case by skipping the WARN and
early return in the event that clkdm->usecount and clk->enable_usecount
are both zero. Presumably this could only happen during the check for
unused clocks at boot-time.
[1] http://article.gmane.org/gmane.linux.ports.arm.omap/88824
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: split the hwmod and clock disable cases; modified the
code to skip the clockdomain handling during the disable-unused-clocks phase;
added COMMON_CLK ifdef; removed include of clk-private.h at Mike's request]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without this kernel would crash, since clkdm inside omap_hwmod
is accessed in some of the init functions like, _init_main_clk.
So call init_clkdm before _init_main_clk().
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Platform code can use omap2_clk_enable_init_clocks() to enable a
list of clocks that are needed to be enabled at init.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: added kerneldoc to non-trivial new function]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Platforms can call omap2_init_clk_hw_omap_clocks() to register a clock
using clk_hw_omap. omap2_clk_enable_autoidle_all() and
omap2_clk_disable_autoidle_all() can then be used to run through
all the clocks which support autoidle to enable/disable them.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: added kerneldoc on non-trivial new functions]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP2420 and OMAP2430 chips each have two on-chip APLLs. When locked,
one APLL generates a 96 MHz rate; the other, a 54 MHz rate.
Previously we treated these clocks as fixed-rate clocks at the locked
rates, but this isn't quite right. The locked rate should be returned
when the APLL is locked, and a zero rate should be returned when the
APLL is stopped. This patch adds the infrastructure that will be used
by the CCF changes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Convert all OMAP2 specific platform files to use COMMON clk
and keep all the changes under the CONFIG_COMMON_CLK macro check
so it does not break any existing code. At a later point switch
to COMMON clk and get rid of all old/legacy code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert all OMAP3 specific platform files to use COMMON clk
and keep all the changes under the CONFIG_COMMON_CLK macro check
so it does not break any existing code. At a later point switch
to COMMON clk and get rid of all old/legacy code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert all OMAP4 specific platform files to use COMMON clk
and keep all the changes under the CONFIG_COMMON_CLK macro check
so it does not break any existing code. At a later point switch
to COMMON clk and get rid of all old/legacy code.
This converts all apis which will be called directly from COMMON
clk to take a struct clk_hw parameter, and all the internal platform
apis to take a struct clk_hw_omap parameter.
Changes are based off the original patch from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: created new omap2_clksel_find_parent_index() rather than
modifying omap2_init_clksel_parent(); moved clkhwops_iclk_wait to
clkt_iclk.c to fix OMAP4-only builds; added clk-provider.h include to clock.h
to try to fix some 3430-builds]
[mturquette@ti.com: squash patch for omap2_clkops_{en,dis}able_clkdm;
omap2_dflt_clk_is_enabled should not enable clocks]
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: fix compiler warning; update to apply; added kerneldoc on
non-trivial new functions; added the dpll3xxx clockdomain modifications]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
hwmod uses deferencing the clk pointer to acccess the clkdm.
With COMMON clk hwoever this will need to be deferenced through
the clk_hw_omap pointer, so do the necessary changes.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
plat/clock.c which has most of usecounting/locking infrastructure will
be used only for OMAP1 until that is moved to use COMMON clk.
reuse most of what plat/clock.h has while we move to common clk, and
move most of what 'struct clk' was as 'struct clk_hw_omap' which
will then be used to define platform specific parameters.
All usecounting/locking related variables from 'struct clk' are
dropped as they will not be used with 'struct clk_hw_omap'.
Based on the original changes from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
arch/arm/mach-omap2/prcm.c and arch/arm/plat-omap/include/plat/prcm.h
are now completely unused and can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
The hwmod code unconditionally calls _omap4_disable_module() on all
SoCs when a module doesn't enable correctly. This "worked" due to the
weak function omap4_cminst_wait_module_idle() in
arch/arm/mach-omap2/prcm.c, which was a no-op. But now those weak
functions are going away - they should not be used. So this patch
will now call the SoC-specific disable_module code, assuming it
exists.
Needs to be done before the weak function is removed, otherwise AM33xx
will crash early in boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Consolidate all of the copies of MAX_MODULE_HARDRESET_WAIT and
MAX_MODULE_SOFTRESET_WAIT into one place, arch/arm/mach-omap2/prm.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Split omap2_set_globals_prcm() into PRM, CM, and PRCM_MPU variants, since
these are all separate IP blocks. This should make it easier to move the
PRM, CM, PRCM_MPU code into drivers/ in future patchsets.
At this point arch/arm/plat-omap/include/plat/prcm.h is empty; a
subsequent patch will remove it, and remove the #include from all the
files that #include it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Now that all users of mach-omap2/omap2_cm_wait_idlest() have been removed,
delete the function and its supporting macros and prototypes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Convert the OMAP clock code's _omap2_module_wait_ready() to use
SoC-independent CM functions that are provided by the CM code, rather
than using a deprecated function from mach-omap2/prcm.c.
This facilitates the future conversion of the CM code to a driver, and
also removes a mach-omap2/prcm.c user. mach-omap2/prcm.c will be removed
by a subsequent patch.
Some modules have IDLEST registers that aren't in the CM module, such
as the AM3517 IDLEST bits. So we also need a fallback function for
these non-CM odd cases. Create a temporary one in mach-omap2/clock.c,
intended to exist until the SCM drivers are ready.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Convert the OMAP2xxx APLL code to use omap2_cm_wait_module_ready(),
and move the low-level CM register manipulation functions to
mach-omap2/cm2xxx.c. The objectives here are to remove the dependency
on the deprecated omap2_cm_wait_idlest() function in
mach-omap2/prcm.c, so that code can be removed later; and move
low-level register accesses to the CM IP block to the CM code, which
will soon be moved into drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Modify the board files to use the SoC-specific system restart
functions. At this point it's possible to remove omap_prcm_restart()
from mach-omap2/prcm.c.
While removing the prototypes for the now-unused restart functions, clean
up a few more obsolete prototypes in mach-omap2/clock.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Split omap_prcm_restart() from mach-omap2/prcm.c into SoC-specific
variants. These functions need to be able to save the reboot reason
into the scratchpad RAM. This implies a dependency on both the PRM
and SCM IP blocks, so they've been moved into their own file. This
will eventually call functions in the PRM and SCM drivers, once those
are created.
Vaibhav Hiremath <hvaibhav@ti.com> identified an unused prototype in
the first version of this patch - now removed. Tony Lindgren
<tony@atomide.com> noted a compile problem with some RMK Kconfigs;
resolved in this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Collect all of the virt_prcm_set-specific clocktype code into
mach-omap2/clkt2xxx_virt_prcm_set.c. Remove its dependency on the
'sclk' and 'vclk' global variables. Those variables will be removed
by subsequent patches.
This is part of the process of cleaning up the OMAP2xxx clock code
and preparing for the removal of the omap_prcm_restart() function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Remove the global 'dclk' variable, instead replacing it with a
variable local to the dpllcore clock type C file. This removes some
of the special-case code surrounding the OMAP2xxx clock init.
This patch is a prerequisite for the removal of the
omap_prcm_restart() code from arch/arm/mach-omap2/prcm.c. It also
cleans up some special-case OMAP2xxx clock code in the process.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Add SoC reset functions into the PRM code. These functions are based
on code from mach-omap2/prcm.c. They reset the SoC using the CORE DPLL
reset method (as opposed to one of the other two or three chip reset
methods).
Adding them here will facilitate their removal from
arch/arm/mach-omap2/prcm.c. (prcm.c is deprecated.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Get rid of the mach-omap2/common.c globals by moving the global
initialization for IP block addresses that must occur early into
mach-omap2/io.c. In the process, remove the *_map_common_io*() and
SoC-specific *set_globals* functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
omap_prcm_get_reset_sources() is now unused; so, remove it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
The OMAP watchdog timer driver directly calls a function exported by
code in arch/arm/mach-omap2. This is not good; it tightly couples
this driver to the mach-omap2 integration code. Instead, add a
temporary platform_data function pointer to abstract this function
call. A subsequent patch will convert the watchdog driver to use this
function pointer.
This patch also moves the device creation code out of
arch/arm/mach-omap2/devices.c and into arch/arm/mach-omap2/wd_timer.c.
This is another step towards the removal of
arch/arm/mach-omap2/devices.c.
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
[paul@pwsan.com: skip wd_timer device creation when DT blob is present]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
An older version of the patch "ARM: OMAP1: create read_reset_sources()
function (for initial use by watchdog)" was sent upstream, which used
the wrong return type for the omap1_get_reset_sources() function.
Fix it to return a u32, which is what the WDTIMER platform_data
function pointer read_reset_sources() expects.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 4c98dc6b8e ("ARM: OMAP: Make
plat/fpga.h local to arch/arm/plat-omap") results in a new warning from
sparse:
arch/arm/mach-omap1/fpga.c:147:6: warning: symbol 'omap1510_fpga_init_irq' was not declared. Should it be static?
Fix by adding a missing include.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Commit 25c7d49ed4 ("ARM: OMAP: Make
omap_device local to mach-omap2") broke an OMAP5912-only build here:
arch/arm/mach-omap1/pm_bus.c: In function 'omap1_pm_runtime_init':
arch/arm/mach-omap1/pm_bus.c:69:2: error: implicit declaration of function
'cpu_class_is_omap1'
make[1]: *** [arch/arm/mach-omap1/pm_bus.o] Error 1
Fix by adding a missing include.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Prepares for the future move of the PRM/CM code to drivers/. Also
includes some prcm.[ch] cleanup patches from the WDTIMER cleanup
series that don't need external acks.
Basic test logs for this branch on top of v3.7-rc2 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121021123719/
But due to the number of unrelated regressions present in v3.7-rc[12],
it's not particularly usable as a testing base. With reverts, fixes,
and workarounds applied as documented in:
http://www.pwsan.com/omap/testlogs/test_v3.7-rc2/20121020134755/README.txt
the following test logs were obtained:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121020231757/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=asxx
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-a-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8/cleanup-prcm
The first set of OMAP PRM/CM-related cleanup patches for 3.8.
Prepares for the future move of the PRM/CM code to drivers/. Also
includes some prcm.[ch] cleanup patches from the WDTIMER cleanup
series that don't need external acks.
Basic test logs for this branch on top of v3.7-rc2 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121021123719/
But due to the number of unrelated regressions present in v3.7-rc[12],
it's not particularly usable as a testing base. With reverts, fixes,
and workarounds applied as documented in:
http://www.pwsan.com/omap/testlogs/test_v3.7-rc2/20121020134755/README.txt
the following test logs were obtained:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121020231757/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/Makefile
arch/arm/mach-omap2/clockdomain2xxx_3xxx.c
arch/arm/mach-omap2/pm24xx.c
In order to make single zImage work for ARM architecture,
we need to make sure we don't depend on private headers.
Move USB platform_data to <linux/platform_data/omap-usb.h>
and add a minimal drivers/mfd/usb-omap.h.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for local mfd/usb-omap.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's move what we can from plat/usb.h to the local usb.h
for ARM common zImage support.
This is needed so we can remove plat/usb.h for ARM common
zImage support.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For omap1, we'll keep mach/serial.h around for 8250.c hardware
workarounds. For omap2+, we no longer need mach/serial.h and
can make it local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to eventually move omap2+ to generic
debug code that's configured in Kconfig for the port.
Signed-off-by: Tony Lindgren <tony@atomide.com>
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQgLn6AAoJEBvUPslcq6VztJIQAMDLmUr4XRa0pV9ASPieMSnP
LqXQ8Gpr8JP6I2A7mjj5K/PVvU2PCIgefX5/F7PssWeDzPs1p6T5eQc6/Oo88j+k
6xIaPJtuU6aiMKiH4QJBU9mfFZN4tvKNX8sJZ4YhzAmkKshwSd2XdWQlkSWYV7Ii
QFRXOdYdX3dgvt3Pv5LYhFMlRDzXlMtCNkdyO0C5yDc038FvT5kxcgpOJ99ndX1F
aSpNPchDwEXP7WZl3O7uZs732hRHQbKraMkzalVJ5mgvLSwF7VsB+BLdjOgRqFfg
edpAPt/izpTk7cg7RQiItrW3xz3eSiN/fiAg2wLvxr6ewzB5DguPLa6DNPF+uyup
BlpQAvNsICIixfKb/qimQBOkB71TTRxqvBnG0Vt/cExS1dTuWlhyCYzA6dhZtl+w
7ETCo7Mmj+L9T1EfzhMPgjWvMZ4Luli4NHSUYxMl5Cs8nu1y6ytIXxH9e0mnZAbK
n4ANoIuFE3ZueXWnHAVCOs0YZj2F1OLB+mFkIFg3OVpB4WCXiOTgJuDNsAAQNS3/
VsYVehNFRB/E/lMWkN293j95LRSwl/sIKbvlpxe7M3XQi4IWh1bDPwcg1YhGPxRV
HIuQSSMIIzcsFoDqbQYv9qzpvslfee58fBV0L8BzMyXNd1lYzWJ5Af6A8ddSVVFS
Hh+btZObC1zP/2IKbImk
=HUTj
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-signed' into omap-for-v3.8/cleanup-headers-serial-take2
This is the first set of omap cleanup patches for v3.8 merge
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
This allows us to get rid of the ifdefs in 8250.c.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP watchdog timer driver needs to determine what caused the SoC
to reset for its GETBOOTSTATUS ioctl. So, define a set of standard
reset sources across OMAP SoCs. For OMAP2xxx, 3xxx, and 4xxx SoCs,
define mappings from the SoC-specific reset source register bits to
the standardized reset source IDs. Create SoC-specific PRM functions
that read the appropriate per-SoC register and use the mapping to
return the standardized reset bits. Register the SoC-specific PRM
functions with the common PRM code via prm_register(). Create a
function in the common PRM code, prm_read_reset_sources(), that
calls the SoC-specific function, registered during boot.
This patch does not yet handle some SoCs, such as AM33xx. Those SoCs
were not handled by the code this will replace.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP1, the existing OMAP watchdog driver reads a register directly
from a non-watchdog IP block. It also does not convert the register's
contents into the standard WDIOF_* bits expected from the
GETBOOTSTATUS ioctl().
To move towards fixing these problems, create an function in
arch/arm/mach-omap1 to return the reset source data. A subsequent
patch will provide this function to the watchdog driver via
platform_data.
In the long term, the best approach would be to move this function
to a new OMAP1 driver that handles access to the OMAP1 Clock
Generation and Reset Management IP block. Then no platform_data would
be needed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There are several CM operations which behave similarly across OMAP2+
SoCs, but which have slight differences in their underlying
implementations.
This patch creates the support code for this function pointer
registration process. No function pointers are included yet, but a
subsequent patch will create these for the module IDLEST registers.
This patch allows other code to use CM-provided data and operations
without needing to know which SoC is currently in use. A further
description of the concept is provided in the patch entitled
"ARM: OMAP2+: PRM: prepare for use of prm_ll_data function pointers".
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There are several PRM operations which behave similarly across OMAP2+
SoCs, but which have slight differences in their underlying
implementations. For example, to fetch the SoC's last reset sources,
different registers are read across OMAP2xxx, 3xxx, and 44xx, and
different bits are used on each SoC. But the information returned is
so similar that a single, common interface for drivers is useful.
This patch creates the support code for this function pointer
registration process. No function pointers are included yet, but a
subsequent patch will create one for the reset source API.
To illustrate the end goal with the above reset source example, each
per-SoC driver will use its own low-level implementation function --
e.g., prm2xxx.c would contain omap2xxx_prm_read_reset_sources(). This
function would read the appropriate register and remap the register
bits to a standard set of reset source bits. When the prm2xxx.c
driver is loaded, it would register this function with the common PRM
driver, prm.c. prm.c would then export a common function,
omap_prm_read_reset_sources(). Calling it would call through to the
function pointer for the currently-registered SoC PRM driver. This
will allow other drivers to use PRM-provided data and operations
without needing to know which SoC is currently in use.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move the low-level SoC-specific clockdomain control functions into
cm*.c and prm*.c. For example, OMAP2xxx low-level clockdomain
functions go into cm2xxx.c. Then remove the unnecessary
clockdomain*xxx*.c files.
The objective is to centralize low-level CM and PRM register accesses
into the cm*.[ch] and prm*.[ch] files, and then to export an OMAP
SoC-independent API to higher-level OMAP power management code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move OMAP3xxx-specific CM functions & macros into cm3xxx.[ch] and
OMAP2xxx-specific macros into cm2xxx.[ch]. Move basic CM register
access functions into static inline functions in cm2xxx_3xxx.h,
leaving only OMAP2/3 hardreset functions in cm2xxx_3xxx.c.
As part of this, split the CM and hwmod code that waits for devices to
become ready into SoC-specific functions.
This is in preparation for the upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move the low-level SoC-specific powerdomain control functions into
prm*.c. For example, OMAP2xxx low-level powerdomain functions go into
prm2xxx.c. Then remove the unnecessary powerdomain*xxx*.c files.
The objective is to centralize low-level PRM register accesses into
the prm*.[ch] files, and then to export an OMAP SoC-independent API to
higher-level OMAP power management code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move OMAP3xxx-specific PRM functions & macros into prm3xxx.[ch] and
OMAP2xxx-specific macros into prm2xxx.h. (prm2xxx.c will be created
by a subsequent patch when it's needed.) Move basic PRM register
access functions into static inline functions in prm2xxx_3xxx.h, leaving
only OMAP2/3 hardreset functions in prm2xxx_3xxx.c.
Also clarify the initcall function naming to reinforce that this code
is specifically for the PRM IP block.
This is in preparation for the upcoming powerdomain series and the
upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Remove the now-unused PRM weak functions from prm_common.c. These
were formerly used to ensure that some OMAP2/3 PRM code would build on
OMAP4, but none of those functions ever would have worked on OMAP4 due
to an incompatible PRM register layout. Now all that has been cleaned
up and these can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
A set of fixes and some minor cleanups for -rc2:
- A series from Arnd that fixes warnings in drivers and other code
included by ARM defconfigs. Most have been acked by corresponding
maintainers (and seem quite hard to argue not picking up anyway in the
few exception cases).
- A few misc patches from the list for integrator/vt8500/i.MX
- A batch of fixes to OMAP platforms, fixing:
- boot problems on beaglebone,
- regression fixes for local timers
- clockdomain locking fixes
- a few boot/sparse warnings
- For Tegra:
- Clock rate calculation overflow fix
- Revert a change that removed timer clocks and a fix for symbol name clashes
- For Renesas:
- IO accessor / annotation cleanups to remove warnings
- For Kirkwood/Dove/mvebu:
- Fixes for device trees for Dove (some minor cleanups, some fixes)
- Fixes for the mvebu gpio driver
- Fix build problem for Feroceon due to missing ifdefs
- Fix lsxl DTS files
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQgembAAoJEIwa5zzehBx3tbwQAJVxDjt0bNFhPDmPVnh4O3qE
qpmCQ4UZ3u153gkXO9973qZNso635yPYtiUA53TAr9kxX4La690IcBOLNMK2TwYZ
enBeg0JtjV+25lkYcsFGnggj8YNXzsL47SVymFxqiu4s4XLuQfUlBWpYyLjYVa6p
1zE5Q6oUVZMJxbqBEK3LaZ9ifV7RxG9xwpx6QiXQlPpZkKqDVYCs/efPXfXBoOeq
KinO/p6fDOQoKrYt1Kdfw5AhmHBrSw/K630/IjZHaIc6j3nDU5UjP0zhO0CE3zDH
NrYctUfJqR9VEKvrpO24RFFYiDaGK1Oge/GhmAAftiLoKK8qxTehKnxe3BUAsMnD
wldxsBBym1rDbr0ehxC9pV6ZtJhA7KZLoPNZpqwSbBYqFnmEG3pZwQV9wToswpmw
1jPJpzZOpe14edHvsixaPuaY3ACnzkkfUWu1wOlg33W5WhPInieMJuJ8hmL+1SVJ
g6Z6/7pjpHhC5CEhVqc5FJjRk1Jk+WsFa1FICoDjnkRW1Hg9DLvdUReEl+8xYuvI
oHqLvDrTabVs9ZDnyT5avBrovWVZjSxZ+TxwMIeQGU1QhW4b8hIjPx09EBb1Hy6F
BiZO3Q9zqm0+C+P1S0Cb3npumwG16ry7f6+51QXRXWNcgWWjm1ggZpWpmPY+g0Ra
BO6UABZwuUm8HzpJaEu1
=alOZ
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc fixes from Olof Johansson:
"A set of fixes and some minor cleanups for -rc2:
- A series from Arnd that fixes warnings in drivers and other code
included by ARM defconfigs. Most have been acked by corresponding
maintainers (and seem quite hard to argue not picking up anyway in
the few exception cases).
- A few misc patches from the list for integrator/vt8500/i.MX
- A batch of fixes to OMAP platforms, fixing:
- boot problems on beaglebone,
- regression fixes for local timers
- clockdomain locking fixes
- a few boot/sparse warnings
- For Tegra:
- Clock rate calculation overflow fix
- Revert a change that removed timer clocks and a fix for symbol
name clashes
- For Renesas:
- IO accessor / annotation cleanups to remove warnings
- For Kirkwood/Dove/mvebu:
- Fixes for device trees for Dove (some minor cleanups, some fixes)
- Fixes for the mvebu gpio driver
- Fix build problem for Feroceon due to missing ifdefs
- Fix lsxl DTS files"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: kirkwood: fix buttons on lsxl boards
ARM: kirkwood: fix LEDs names for lsxl boards
ARM: Kirkwood: fix disabling CACHE_FEROCEON_L2
gpio: mvebu: Add missing breaks in mvebu_gpio_irq_set_type
ARM: dove: Add crypto engine to DT
ARM: dove: Remove watchdog from DT
ARM: dove: Restructure SoC device tree descriptor
ARM: dove: Fix clock names of sata and gbe
ARM: dove: Fix tauros2 device tree init
ARM: dove: Add pcie clock support
ARM: OMAP2+: Allow kernel to boot even if GPMC fails to reserve memory
ARM: OMAP: clockdomain: Fix locking on _clkdm_clk_hwmod_enable / disable
ARM: s3c: mark s3c2440_clk_add as __init_refok
spi/s3c64xx: use correct dma_transfer_direction type
ARM: OMAP4: devices: fixup OMAP4 DMIC platform device error message
ARM: OMAP2+: clock data: Add dev-id for the omap-gpmc dummy fck
ARM: OMAP: resolve sparse warning concerning debug_card_init()
ARM: OMAP4: Fix twd_local_timer_register regression
ARM: tegra: add tegra_timer clock
ARM: tegra: rename tegra system timer
...
A collection of warning fixes on non-ARM code from Arnd Bergmann:
* 'testing/driver-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: s3c: mark s3c2440_clk_add as __init_refok
spi/s3c64xx: use correct dma_transfer_direction type
pcmcia: sharpsl: don't discard sharpsl_pcmcia_ops
USB: EHCI: mark ehci_orion_conf_mbus_windows __devinit
mm/slob: use min_t() to compare ARCH_SLAB_MINALIGN
SCSI: ARM: make fas216_dumpinfo function conditional
SCSI: ARM: ncr5380/oak uses no interrupts
