The Linksys AE3000 device is based on the RT3573
chipset. The support for this chipset is available
already, and the AE3000 device works with the driver.
Only managed mode works correctly at the moment,
for AP mode additional changes are needed in the
driver.
Also add a new RT2800USB_RT3573 Kconfig option and
only enable support for RT3573 based devices if
that is enabled.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RT3593 chipset requires different [RT]XWI size
values. Modify the driver to use the correct values.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for the RT3593 has been implemented in
the previous changes, so it is safe to mark it
supported in the driver.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for the RF3053 has been implemented in
the previous changes, so it is safe to mark it
supported in the driver.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RT3593_ChipSwitchChannel in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
References:
FreqItems3053 in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The actual code uses two default TX power values.
This is enough for 1T and for 2T devices however
on 3T devices another value is needed for the third
chain.
Add a new field to struct channel_info and initialize
it from the 'rt2800_probe_hw_mode' function. Also modify
the 'rt2800_config_channel' to handle the new field as
well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LNA_A[12] gain values are stored at a different
offset in the EEPROM on RT3593 based devices. However
the current code unconditionally reads those values
from the location used by other chipsets.
Fix the code to use the correct EEPROM offset.
Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
References:
RT3593_EEPROM_RSSI2_OFFSET_ALNAGAIN1_24G_READ in include/chip/rt3593.h
RT3593_EEPROM_RSSI2_OFFSET_ALNAGAIN2_5G_READ in include/chip/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The reference code uses hardcoded zero TX mixer gain value
for RT3593. Do the same in the rt2x00 driver.
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
NICReadEEPROMParameters in common/rtmp_init.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the TX mixer gain reading code into separate
helper functions in preparation for RT3593 support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX power values in the EEPROM are using
a different format for the RT3593 chip. The
default TX power value uses bits 0..4 only.
Bits 5..8 contains value for fine grained
power control. Additionally, the lower and
upper limits of the TX power values are the
same for both bands.
Improve the rt2800_txpower_to_dev function,
in order to compute the correct default power
values for the RT3593 chip as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new helper function for converting
the default TX power values from EEPROM into
mac80211 values.
The change improves the readability and it makes
it easier to add support for other chipsets.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On the RT3593 chipset, BBP register 86 must be
configured by different values based on the RX
antenna numbers.
Configure this register from the 'rt2800_config_ant'
function.
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RT3593_CONFIG_SET_BY_ANTENNA in include/chip/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The field must be set to 2 instead of 0 for
devices with three TX chains.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
References:
RTMPReadTxPwrPerRateExt in chips/rt3593.c
RT3593_AsicGetTxPowerOffset in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RT3593_PostBBPInitialization in chips/rt3553.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
References:
NICInitRT3593RFRegisters in chips/rt3593.c
RT3593LoadRFNormalModeSetup in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
References:
NICInitRT3593BbpRegisters in chips/rt3593.c
NICInitBBP in common/rtmp_init.c
NICInitAsicFromEEPROM in common/rtmp_init.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
NICInitRT3593MacRegisters in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Three-chain devices are using a different
EEPROM layout than the rest of the chipsets.
Add a new map which describes the new layout
and use that for the RT3593 chipset.
The index values has been computed from the
EEPROM_EXT_* defines, which can be found in
the 'include/chip/rt3593.h' file in the
Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of assign the offset value to the
enum directly use a new helper function to
convert a rt2800_eeprom_word enum into an
index of the rt2x00_dev->eeprom array.
The patch does not change the existing
behaviour, but makes it possible to add
support for three-chain devices which are
using a different EEPROM layout.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new helper function and use that for reading
single elements of various arrays in the EEPROM.
The patch does not change the current behaviour,
but it allows to use sequential values for the
rt2800_eeprom_word enums. The conversion will be
implemented in a subsequent change.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch adds rt2800 specific functions for
EEPROM data access and changes the code to use
these instead of the generic rt2x00_eeprom_*
variants.
To avoid functional changes, the new functions
are wrappers around the corresponding generic
rt2x00_eeprom_* routines for now. Functional
changes will be implemented in additional patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch converts the EEPROM_* word address defines
into new enum values. The new enum type will be used
by new functions which will be introduced in subsequent
changes.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, RTS threshold is not handled for HT. Handle
user-specified threshold values for both aggregated
and unaggregated frames. Use the wiphy's threshold
parameter for now, it can be made per-VIF later on.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the platform doesn't have rfkill support, i.e. nothing
is connected to the rfkill GPIO, there's little value in
polling the GPIO. Add a Kconfig option to allow disabling
the polling in ath9k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert the mwifiex/pci driver to use dev_pm_ops for power management and
remove Legacy PM handling. This change re-uses existing suspend and resume
interfaces for dev_pm_ops, and changes CONFIG_PM ifdefs to CONFIG_PM_SLEEP
as the driver does not support run-time PM.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Calling kthread_run with a single name parameter causes it to be handled
as a format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the workqueue creation interfaces that do not expect format strings,
make sure they cannot accidently be parsed that way. Additionally, clean
up calls made with a single parameter that would be handled as a format
string. Many callers are passing potentially dynamic string content, so
use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull second set of VFS changes from Al Viro:
"Assorted f_pos race fixes, making do_splice_direct() safe to call with
i_mutex on parent, O_TMPFILE support, Jeff's locks.c series,
->d_hash/->d_compare calling conventions changes from Linus, misc
stuff all over the place."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
Document ->tmpfile()
ext4: ->tmpfile() support
vfs: export lseek_execute() to modules
lseek_execute() doesn't need an inode passed to it
block_dev: switch to fixed_size_llseek()
cpqphp_sysfs: switch to fixed_size_llseek()
tile-srom: switch to fixed_size_llseek()
proc_powerpc: switch to fixed_size_llseek()
ubi/cdev: switch to fixed_size_llseek()
pci/proc: switch to fixed_size_llseek()
isapnp: switch to fixed_size_llseek()
lpfc: switch to fixed_size_llseek()
locks: give the blocked_hash its own spinlock
locks: add a new "lm_owner_key" lock operation
locks: turn the blocked_list into a hashtable
locks: convert fl_link to a hlist_node
locks: avoid taking global lock if possible when waking up blocked waiters
locks: protect most of the file_lock handling with i_lock
locks: encapsulate the fl_link list handling
locks: make "added" in __posix_lock_file a bool
...
John W. Linville says:
====================
Yet one more pull request for wireless updates intended for 3.11...
For the mac80211 bits, Johannes says:
"Here we have a few memory leak fixes related to BSS struct handling
mostly from Ben, including a fix for a more theoretical problem
(associating while a BSS struct times out) from myself, a compilation
warning fix from Arend, mesh fixes from Thomas, tracking the beacon
bitrate (Alex), a bandwidth change event fix (Ilan) and some initial
work for 5/10 MHz channels from Simon."
Regarding the iwlwifi bits, Johannes says:
"Emmanuel removed some unneeded/unsupported module parameters and adds a
Bluetooth 1x1 lookup-table for some upcoming products. From Alex I have
an older patch to add low-power receive support, this depended on a
mac80211 commit that only just came in with the merge from wireless-next
I did. Ilan made beacon timings better, and Eytan added some debug
statements for thermal throttling. I have a few cleanups, a fix for a
long-standing but rare warning, and, arguably the most important patch
here, the firmware API version bump for the 7260/3160 devices."
Also included is a Bluetooth pull -- Gustavo says:
"Here goes a set of patches to 3.11. The biggest work here is from Andre Guedes
on the move of the Discovery to use the new request framework. Other than that
Johan provided a bunch of fixes to the L2CAP code. The rest are just small
fixes and clean ups."
On top of all that, there are a variety of updates and fixes to
brcmfmac, rt2x00, wil6210, ath9k, ath10k, and a few others here and
there. This also includes a pull of the wireless tree, in order to
prevent some merge conflicts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
CC drivers/net/wireless/ath/ath10k/mac.o
drivers/net/wireless/ath/ath10k/mac.c: In function ‘chan_to_phymode’:
drivers/net/wireless/ath/ath10k/mac.c:229:3: warning: enumeration value ‘NL80211_CHAN_WIDTH_5’ not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/mac.c:229:3: warning: enumeration value ‘NL80211_CHAN_WIDTH_10’ not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/mac.c:247:3: warning: enumeration value ‘NL80211_CHAN_WIDTH_5’ not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/mac.c:247:3: warning: enumeration value ‘NL80211_CHAN_WIDTH_10’ not handled in switch [-Wswitch]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed so the interface combination can still be
validated when CONFIG_MAC80211_MESH is not enabled.
Otherwise wiphy registration fails.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the code of the receive path some code was dealing with how
things were done in older kernels. Not really needed for an
upstream driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the receive path a spinlock is taken upon parsing the TLV signal
header. This moves to locking to the TLV handling functions where
it protects the data structures.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivial cleanup of debug messages.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transmit packets needs to be tagged in order to receive a tx status
feedback from the firmware. Determine the tag in the netdev transmit
callback instead of determining the tag just before transfer to the
device. This reduces the number of exception flows and hence makes
the driver code simpler.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DMA engine of some old SDIO host controllers require block size alignment for
data length of each scatterlist item. This patch introduces an intermediate
buffer list to support this kind of platform. It decreases the throughput
because of an extra memcpy in critical data path. So don't turn this on unless
it's necessary.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a unified dongle backplane address preparation function
brcmf_sdio_addrprep to replace duplicate address prep code.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove SDIO_REQ_ASYNC from brcmfmac since it is not being used.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Used NL80211_NUM_ACS to indicate the BCMC fifo used in the driver
which has the same value now, but it is a bad idea relying on that.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When getting a transmit packet from the networking layer simply
enqueue the packet unconditional and have it handled by the dequeue
worker. The transfer of the packet to the bus-specific driver part
is now done from one context.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows enabling support for extra hardware with just a module
param, without kernel/module recompilation.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
