sugov_start() only initializes struct sugov_cpu per-CPU structures
for shared policies, but it should do that for single-CPU policies too.
That in particular makes the IO-wait boost mechanism work in the
cases when cpufreq policies correspond to individual CPUs.
Fixes: 21ca6d2c52 (cpufreq: schedutil: Add iowait boosting)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
qcom_smd_register_edge() is provided by either QCOM_SMD or RPMSG_QCOM_SMD,
and if both of them are disabled, it does nothing.
The check for the PIL drivers however only checks for QCOM_SMD, so it breaks
with QCOM_SMD=n && RPMSG_QCOM_SMD=m:
drivers/remoteproc/built-in.o: In function `smd_subdev_remove':
qcom_wcnss_iris.c:(.text+0x231c): undefined reference to `qcom_smd_unregister_edge'
drivers/remoteproc/built-in.o: In function `smd_subdev_probe':
qcom_wcnss_iris.c:(.text+0x2344): undefined reference to `qcom_smd_register_edge'
drivers/remoteproc/built-in.o: In function `smd_subdev_probe':
qcom_q6v5_pil.c:(.text+0x3538): undefined reference to `qcom_smd_register_edge'
qcom_q6v5_pil.c:(.text+0x3538): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `qcom_smd_register_edge'
This clarifies the Kconfig dependency.
Fixes: 4b48921a8f ("remoteproc: qcom: Use common SMD edge handler")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In the 'commit ebee76f7fa ("ath10k: allow setting coverage class")',
it inherits the design and the address offset from ath9k, but the address
is not applicable to QCA6174, which leads to a random crash while doing the
resume() operation, since the set_coverage_class.ops will be called from
ieee80211_reconfig() when resume() (if the wow is not configured).
Fix the incorrect address offset here to avoid the random crash.
Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2.
kvalo: this also seems to fix a regression with firmware restart.
Fixes: ebee76f7fa ("ath10k: allow setting coverage class")
Cc: <stable@vger.kernel.org> # v4.10
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds to account free nids for each NAT blocks, and while
scanning all free nid bitmap, do check count and skip lookuping in
full NAT block.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This is to avoid build warning reported by kbuild test robot.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch fixes that SSR can overwrite previous warm node block consisting of
a node chain since the last checkpoint.
Fixes: 5b6c6be2d8 ("f2fs: use SSR for warm node as well")
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The new syscall statx is implemented as generic code, so enable it
for architectures like openrisc which use the generic syscall table.
Fixes: a528d35e8b ("statx: Add a system call to make enhanced file info available")
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This tested patch adds missing initialization for Line-In/Out PINs for
the docking station for HP 840 G3.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This tested patch adds missing initialization for Line-In/Out PINs for
the docking station for HP 820 G2.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We concluded there may be a window where the idle wakeup code could get
to pnv_wakeup_tb_loss() (which clobbers non-volatile GPRs), but the
hardware may set SRR1[46:47] to 01b (no state loss) which would result
in the wakeup code failing to restore non-volatile GPRs.
I was not able to trigger this condition with trivial tests on real
hardware or simulator, but the ISA (at least 2.07) seems to allow for
it, and Gautham says that it can happen if there is an exception pending
when the sleep/winkle instruction is executed.
Fixes: 1706567117 ("powerpc/kvm: make hypervisor state restore a function")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit e66f81bbd7 ("clk: sunxi-ng: Implement factors offsets"), the
final formula of NKMP clocks' recalc_rate is refactored; however, the
refactored formula broke the calculation due to some C language operand
priority problem -- the priority of operand >> is lower than * and /,
makes the formula being parsed as "(parent_rate * n * k) >> (p / m)", but
it should be "(parent_rate * n * k >> p) / m".
Add the pair of parentheses to fix up this issue. This pair of
parentheses used to exist in the old formula.
Fixes: e66f81bbd7 ("clk: sunxi-ng: Implement factors offsets")
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fix a boundary condition where in some cases an eeh event with state ==
pci_channel_io_perm_failure wont be passed on to a driver attached to
the virtual PCI device associated with a slice. This will happen in case
the slice just before (n-1) doesn't have any vPHB bus associated with
it, that results in an early return from cxl_pci_error_detected()
callback.
With state == pci_channel_io_perm_failure, the adapter will be removed
irrespective of the return value of cxl_vphb_error_detected(). So we now
always return PCI_ERS_RESULT_DISCONNECTED for this case i.e even if
the AFU isn't using a vPHB (currently returns PCI_ERS_RESULT_NONE).
Fixes: e4f5fc001a6("cxl: Do not create vPHB if there are no AFU configuration records")
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the commit [15c75b09f8: ALSA: ctxfi: Fallback DMA mask to 32bit],
I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while
cthw20k2.c is OK). This patch fixes that obvious bug.
(As a side note: although the original commit was completely wrong,
it's still working for most of machines, as it sets to 32bit DMA mask
in the end. So the bug severity is low.)
Fixes: 15c75b09f8 ("ALSA: ctxfi: Fallback DMA mask to 32bit")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mult/div for osc12M was previously backwards (giving a 48M rate
for osc12M). Fix it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The bl_en_pin GPIO pinmux is configured as "gpio_in", which makes it
conflicts with the real GPIO usage (out), and makes the backlight not
usable.
Drop the GPIO pinmux for it, thus this GPIO can be correctly used.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CPU port of the BCM53125 is configured with RGMII (no delays) but
this should actually be RGMII with transmit delay (rgmii-txid) because
STMMAC takes care of inserting the transmitter delay. This fixes
occasional packet loss encountered.
Fixes: d7b9eaff5f ("ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This BUG_ON() triggered for me once at shutdown, and I don't see a
reason for the check. The code correctly checks whether the swap slot
cache is usable or not, so an uninitialized swap slot cache is not
actually problematic afaik.
I've temporarily just switched the BUG_ON() to a WARN_ON_ONCE(), since
I'm not sure why that seemingly pointless check was there. I suspect
the real fix is to just remove it entirely, but for now we'll warn about
it but not bring the machine down.
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Wire up statx() syscall
- Don't print a warning on memory hotplug when HPT resizing isn't available
Thanks to:
David Gibson, Chandan Rajendra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TfiW
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc fixes from Michael Ellerman:
"A couple of minor powerpc fixes for 4.11:
- wire up statx() syscall
- don't print a warning on memory hotplug when HPT resizing isn't
available
Thanks to: David Gibson, Chandan Rajendra"
* tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Don't give a warning when HPT resizing isn't available
powerpc: Wire up statx() syscall
Pull parisc fixes from Helge Deller:
- Mikulas Patocka added support for R_PARISC_SECREL32 relocations in
modules with CONFIG_MODVERSIONS.
- Dave Anglin optimized the cache flushing for vmap ranges.
- Arvind Yadav provided a fix for a potential NULL pointer dereference
in the parisc perf code (and some code cleanups).
- I wired up the new statx system call, fixed some compiler warnings
with the access_ok() macro and fixed shutdown code to really halt a
system at shutdown instead of crashing & rebooting.
* 'parisc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix system shutdown halt
parisc: perf: Fix potential NULL pointer dereference
parisc: Avoid compiler warnings with access_ok()
parisc: Wire up statx system call
parisc: Optimize flush_kernel_vmap_range and invalidate_kernel_vmap_range
parisc: support R_PARISC_SECREL32 relocation in modules
Pull SCSI target fixes from Nicholas Bellinger:
"The bulk of the changes are in qla2xxx target driver code to address
various issues found during Cavium/QLogic's internal testing (stable
CC's included), along with a few other stability and smaller
miscellaneous improvements.
There are also a couple of different patch sets from Mike Christie,
which have been a result of his work to use target-core ALUA logic
together with tcm-user backend driver.
Finally, a patch to address some long standing issues with
pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices,
which will make folks using physical (or virtual) magnetic tape happy"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
qla2xxx: Update driver version to 9.00.00.00-k
qla2xxx: Fix delayed response to command for loop mode/direct connect.
qla2xxx: Change scsi host lookup method.
qla2xxx: Add DebugFS node to display Port Database
qla2xxx: Use IOCB interface to submit non-critical MBX.
qla2xxx: Add async new target notification
qla2xxx: Export DIF stats via debugfs
qla2xxx: Improve T10-DIF/PI handling in driver.
qla2xxx: Allow relogin to proceed if remote login did not finish
qla2xxx: Fix sess_lock & hardware_lock lock order problem.
qla2xxx: Fix inadequate lock protection for ABTS.
qla2xxx: Fix request queue corruption.
qla2xxx: Fix memory leak for abts processing
qla2xxx: Allow vref count to timeout on vport delete.
tcmu: Convert cmd_time_out into backend device attribute
tcmu: make cmd timeout configurable
tcmu: add helper to check if dev was configured
target: fix race during implicit transition work flushes
target: allow userspace to set state to transitioning
target: fix ALUA transition timeout handling
...
Pull device-dax fixes from Dan Williams:
"The device-dax driver was not being careful to handle falling back to
smaller fault-granularity sizes.
The driver already fails fault attempts that are smaller than the
device's alignment, but it also needs to handle the cases where a
larger page mapping could be established. For simplicity of the
immediate fix the implementation just signals VM_FAULT_FALLBACK until
fault-size == device-alignment.
One fix is for -stable to address pmd-to-pte fallback from the
original implementation, another fix is for the new (introduced in
4.11-rc1) pud-to-pmd regression, and a typo fix comes along for the
ride.
These have received a build success notification from the kbuild
robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix debug output typo
device-dax: fix pud fault fallback handling
device-dax: fix pmd/pte fault fallback handling
Fixes: 290a6ce11d (iio: imu: add support to lsm6dsx driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.
Following commands are being routed through IOCB interface
- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The main lock that needs to be held for CMD or TMR submission
to upper layer is the sess_lock. The sess_lock is used to
serialize cmd submission and session deletion. The addition
of hardware_lock being held is not necessary. This patch removes
hardware_lock dependency from CMD/TMR submission.
Use hardware_lock only for error response in this case.
Path1
CPU0 CPU1
---- ----
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
Path2/deadlock
*** DEADLOCK ***
Call Trace:
dump_stack+0x85/0xc2
print_circular_bug+0x1e3/0x250
__lock_acquire+0x1425/0x1620
lock_acquire+0xbf/0x210
_raw_spin_lock_irqsave+0x53/0x70
qlt_sess_work_fn+0x21d/0x480 [qla2xxx]
process_one_work+0x1f4/0x6e0
Cc: <stable@vger.kernel.org>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reported-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Normally, ABTS is sent to Target Core as Task MGMT command.
In the case of error, qla2xxx needs to send response, hardware_lock
is required to prevent request queue corruption.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of putting cmd_time_out under ../target/core/user_0/foo/control,
which has historically been used by parameters needed for initial
backend device configuration, go ahead and move cmd_time_out into
a backend device attribute.
In order to do this, tcmu_module_init() has been updated to create
a local struct configfs_attribute **tcmu_attrs, that is based upon
the existing passthrough_attrib_attrs along with the new cmd_time_out
attribute. Once **tcm_attrs has been setup, go ahead and point
it at tcmu_ops->tb_dev_attrib_attrs so it's picked up by target-core.
Also following MNC's previous change, ->cmd_time_out is stored in
milliseconds but exposed via configfs in seconds. Also, note this
patch restricts the modification of ->cmd_time_out to before +
after the TCMU device has been configured, but not while it has
active fabric exports.
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A single daemon could implement multiple types of devices
using multuple types of real devices that may not support
restarting from crashes and/or handling tcmu timeouts. This
makes the cmd timeout configurable, so handlers that do not
support it can turn if off for now.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This adds a helper to check if the dev was configured. It
will be used in the next patch to prevent updates to some
config settings after the device has been setup.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
-----BEGIN PGP SIGNATURE-----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=lNoR
-----END PGP SIGNATURE-----
Merge tag 'openrisc-for-linus' of git://github.com/openrisc/linux
Pull OpenRISC fixes from Stafford Horne:
"OpenRISC fixes for build issues that were exposed by kbuild robots
after 4.11 merge. All from allmodconfig builds. This includes:
- bug in the handling of 8-byte get_user() calls
- module build failure due to multile missing symbol exports"
* tag 'openrisc-for-linus' of git://github.com/openrisc/linux:
openrisc: Export symbols needed by modules
openrisc: fix issue handling 8 byte get_user calls
openrisc: xchg: fix `computed is not used` warning
This fixes the following races:
1. core_alua_do_transition_tg_pt could have read
tg_pt_gp_alua_access_state and gone into this if chunk:
if (!explicit &&
atomic_read(&tg_pt_gp->tg_pt_gp_alua_access_state) ==
ALUA_ACCESS_STATE_TRANSITION) {
and then core_alua_do_transition_tg_pt_work could update the
state. core_alua_do_transition_tg_pt would then only set
tg_pt_gp_alua_pending_state and the tg_pt_gp_alua_access_state would
not get updated with the second calls state.
2. core_alua_do_transition_tg_pt could be setting
tg_pt_gp_transition_complete while the tg_pt_gp_transition_work
is already completing. core_alua_do_transition_tg_pt then waits on the
completion that will never be called.
To handle these issues, we just call flush_work which will return when
core_alua_do_transition_tg_pt_work has completed so there is no need
to do the complete/wait. And, if core_alua_do_transition_tg_pt_work
was running, instead of trying to sneak in the state change, we just
schedule up another core_alua_do_transition_tg_pt_work call.
Note that this does not handle a possible race where there are multiple
threads call core_alua_do_transition_tg_pt at the same time. I think
we need a mutex in target_tg_pt_gp_alua_access_state_store.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Userspace target_core_user handlers like tcmu-runner may want to set the
ALUA state to transitioning while it does implicit transitions. This
patch allows that state when set from configfs.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The implicit transition time tells initiators the min time
to wait before timing out a transition. We currently schedule
the transition to occur in tg_pt_gp_implicit_trans_secs
seconds so there is no room for delays. If
core_alua_do_transition_tg_pt_work->core_alua_update_tpg_primary_metadata
needs to write out info to a remote file, then the initiator can
easily time out the operation.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If tcmu-runner is processing a STPG and needs to change the kernel's
ALUA state then we cannot use the same work queue for task management
requests and ALUA transitions, because we could deadlock. The problem
occurs when a STPG times out before tcmu-runner is able to
call into target_tg_pt_gp_alua_access_state_store->
core_alua_do_port_transition -> core_alua_do_transition_tg_pt ->
queue_work. In this case, the tmr is on the work queue waiting for
the STPG to complete, but the STPG transition is now queued behind
the waiting tmr.
Note:
This bug will also be fixed by this patch:
http://www.spinics.net/lists/target-devel/msg14560.html
which switches the tmr code to use the system workqueues.
For both, I am not sure if we need a dedicated workqueue since
it is not a performance path and I do not think we need WQ_MEM_RECLAIM
to make forward progress to free up memory like the block layer does.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We do not setup the LU group for pscsi devices, so if you write
a state to alua_access_state that will cause a transition you will
get a NULL pointer dereference.
This patch will fail attempts to try and transition the path
for backend devices that set the TRANSPORT_FLAG_PASSTHROUGH_ALUA
flag.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch allows passthrough backends to use the core/base LIO
ALUA setup and state checks, but still handle the execution of
commands.
This will allow the target_core_user module to execute STPG and RTPG
in userspace, and not have to duplicate the ALUA state checks, path
information (needed so we can check if command is executable on
specific paths) and setup (rtslib sets/updates the configfs ALUA
interface like it does for iblock or file).
For STPG, the target_core_user userspace daemon, tcmu-runner will
still execute the STPG, and to update the core/base LIO state it
will use the existing configfs interface. For RTPG, tcmu-runner
will loop over configfs and/or cache the state.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>