Add support for setting debounce on a line via the GPIO uAPI.
Where debounce is not supported by hardware, a software debounce is
provided.
The implementation of the software debouncer waits for the line to be
stable for the debounce period before determining if a level change,
and a corresponding edge event, has occurred. This provides maximum
protection against glitches, but also introduces a debounce_period
latency to edge events.
The software debouncer is integrated with the edge detection as it
utilises the line interrupt, and integration is simpler than getting
the two to interwork. Where software debounce AND edge detection is
required, the debouncer provides both.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for edge detection to lines requested using
GPIO_V2_GET_LINE_IOCTL.
The edge_detector implementation is based on the v1 lineevent
implementation. Unlike the v1 implementation, an overflow of the event
buffer results in discarding older events, rather than the most
recent, so the final event in a burst will correspond to the current
state of the line.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Replace usage of atomic_notifier_call_chain with
blocking_notifier_call_chain as the notifier function,
lineinfo_changed_notify, calls gpio_desc_to_lineinfo,
which calls pinctrl_gpio_can_use_line, which can sleep.
The chain isn't being called from an atomic context so the
the blocking notifier is a suitable substitute.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Move gpiolib-sysfs function declarations into their own header.
These functions are in gpiolib-sysfs.c, and are only required by gpiolib.c,
and so should be in a module header, not gpiolib.h.
This brings gpiolib-sysfs into line with gpiolib-cdev, and is another step
towards removing the sysfs inferface.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
As GPIO hogs are configured at GPIO controller initialization time,
adding/removing GPIO hogs in DT overlays does not work.
Add support for GPIO hogs described in DT overlays by registering an OF
reconfiguration notifier, to handle the addition and removal of GPIO hog
subnodes to/from a GPIO controller device node.
Note that when a GPIO hog device node is being removed, its "gpios"
properties is no longer available, so we have to keep track of which
node a hog belongs to, which is done by adding a pointer to the hog's
device node to struct gpio_desc.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200220130149.26283-3-geert+renesas@glider.be
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently there is no way for user-space to be informed about changes
in status of GPIO lines e.g. when someone else requests the line or its
config changes. We can only periodically re-read the line-info. This
is fine for simple one-off user-space tools, but any daemon that provides
a centralized access to GPIO chips would benefit hugely from an event
driven line info synchronization.
This patch adds a new ioctl() that allows user-space processes to reuse
the file descriptor associated with the character device for watching
any changes in line properties. Every such event contains the updated
line information.
Currently the events are generated on three types of status changes: when
a line is requested, when it's released and when its config is changed.
The first two are self-explanatory. For the third one: this will only
happen when another user-space process calls the new SET_CONFIG ioctl()
as any changes that can happen from within the kernel (i.e.
set_transitory() or set_debounce()) are of no interest to user-space.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
- improvements in the gpio-pca953x driver
- use platform_irq_count() in gpio-mvebu and gpio-bcm-kona
- remove unneeded MODULE_VERSION() usage in the gpio directory
- irq-related improvements in gpio-tegra driver
- several improvements for the core subsystem code: fix confusing indentation,
fix int type casting, unduplicate code in several places
-----BEGIN PGP SIGNATURE-----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=ia2k
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.6-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.6
- improvements in the gpio-pca953x driver
- use platform_irq_count() in gpio-mvebu and gpio-bcm-kona
- remove unneeded MODULE_VERSION() usage in the gpio directory
- irq-related improvements in gpio-tegra driver
- several improvements for the core subsystem code: fix confusing indentation,
fix int type casting, unduplicate code in several places
gpiochip_get_desc() takes a u16 hwnum, but it turns out most users don't
respect that and usually pass an unsigned int. Since implicit casting to
a smaller type is dangerous - let's change the type of hwnum to unsigned
int in gpiochip_get_desc() and in gpiochip_request_own_desc() where the
size of hwnum is not respected either and who's a user of the former.
This is safe as we then check the hwnum against the number of lines
before proceeding in gpiochip_get_desc().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The string literal "gpiochip" is used in several places.
Add a definition for it, and use it everywhere, to make sure everything
stays in sync.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191127084253.16356-2-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow pull up/down bias to be disabled, allowing the line to float
or to be biased only by external circuitry.
Use case is for where the bias has been applied previously, either
by default or by the user, but that setting may conflict with the
current use of the line.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This is a follow up to the commit
f626d6dfb7 ("gpio: of: Break out OF-only code")
which broke down OF parts of GPIO library. Here we do the similar to ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190730104337.21235-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The core gpiolib should not contain any OF/device tree-only
code. Try to break out the main part of it and push it down
into the optional gpiolib-of.c part of the library.
Create a local gpiolib-of.h header and move stuff around a
bit to get a clean cut.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190717071001.3858-1-linus.walleij@linaro.org
For spinlocks the type spinlock_t should be used instead of "struct
spinlock".
Use spinlock_t for spinlock's definition.
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20190704153803.12739-8-bigeasy@linutronix.de
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to
be handled consistently. Unsurprisingly, we enforce the lines to
be either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone
does, so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed.
Such nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs
and outputs at the same time and after improving the MMIO library
we handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM
work as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update.
-----BEGIN PGP SIGNATURE-----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=rhto
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.2 kernel cycle. A bit
later than usual because I was ironing out my own mistakes. I'm
holding some stuff back for the next kernel as a result, and this
should be a healthy and well tested batch.
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to be
handled consistently. Unsurprisingly, we enforce the lines to be
either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone does,
so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed. Such
nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs and
outputs at the same time and after improving the MMIO library we
handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM work
as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update"
* tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: Update documentation
docs: gpio: convert docs to ReST and rename to *.rst
gpio: sch: Remove write-only core_base
gpio: pxa: Make two symbols static
gpiolib: acpi: Respect pin bias setting
gpiolib: acpi: Add acpi_gpio_update_gpiod_lookup_flags() helper
gpiolib: acpi: Set pin value, based on bias, more accurately
gpiolib: acpi: Change type of dflags
gpiolib: Introduce GPIO_LOOKUP_FLAGS_DEFAULT
gpiolib: Make use of enum gpio_lookup_flags consistent
gpiolib: Indent entry values of enum gpio_lookup_flags
gpio: pca953x: add support for pca6416
dt-bindings: gpio: pca953x: document the nxp,pca6416
gpio: pca953x: add pcal6416 to the of_device_id table
gpio: gpio-omap: Remove conditional pm_runtime handling for GPIO interrupts
gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup
tracing: stop making gpio tracing configurable
gpio: pca953x: Configure wake-up path when wake-up is enabled
gpio: of: Optimize quirk checks
gpio: mmio: Drop bgpio_dir_inverted
...
For now, we don't take into account the pin bias settings supplied by ACPI.
This change is targeting the mentioned gap.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This helper consolidates all settings of GPIO descriptor lookup flags and
quirks in the future if any.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The library uses enum gpio_lookup_flags to define the possible
characteristics of GPIO pin. Since enumerator listed only individual
bits the common use of it is in a form of a bitmask of
gpio_lookup_flags GPIO_* values. The more correct type for this is
unsigned long.
Due to above convert all users to use unsigned long instead of
enum gpio_lookup_flags except enumerator definition.
While here, make field and parameter descriptions consistent as well.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function is needed in mcp23s08. That driver is a special snowflake
because it supports several hardware chips as a single "GPIO chip" under
Linux.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Phil Reid <preid@electromag.com.au>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds support for configuring the pull-up and pull-down
resistors available in some GPIO controllers. While configuring
pull-up/pull-down is already possible through the pinctrl subsystem,
some GPIO controllers, especially simple ones such as GPIO expanders
on I2C, don't have any pinmuxing capability and therefore do not use
the pinctrl subsystem.
This commit implements the GPIO_PULL_UP and GPIO_PULL_DOWN flags,
which can be used from the Device Tree, to enable a pull-up or
pull-down resistor on a given GPIO.
The flag is simply propagated all the way to the core GPIO subsystem,
where it is used to call the gpio_chip ->set_config callback with the
appropriate existing PIN_CONFIG_BIAS_* values.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function already exist inside gpiolib, we were just
reluctant to make it available to the kernel at large as
the devm_* seemed to be enough for anyone.
However we found out that regulators need to do their own
lifecycle/refcounting on GPIO descriptors and explicitly
call gpiod_put() when done with a descriptor, so export
this function so we can hand the refcounting over to the
regulator core for these descriptors after retrieveal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the SPDX headers and cut down on boilerplate to indicate the
license in the core gpiolib implementation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Certain GPIO array lookup results may map directly to GPIO pins of a
single GPIO chip in hardware order. If that condition is recognized
and handled efficiently, significant performance gain of get/set array
functions may be possible.
While processing a request for an array of GPIO descriptors, identify
those which represent corresponding pins of a single GPIO chip. Skip
over pins which require open source or open drain special processing.
Moreover, identify pins which require inversion. Pass a pointer to
that information with the array to the caller so it can benefit from
enhanced performance as soon as get/set array functions can accept and
make efficient use of it.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO drivers call gpiochip_(un)lock_as_irq whenever they want to use a gpio
as an interrupt. This is done when the irq is requested and it marks the
gpio as in use by an interrupt.
This is problematic for cases where a gpio pin is used as an interrupt
pin, then, after the irq is disabled, is used as a regular gpio pin.
Currently it is not possible to do this other than by first freeing
the interrupt so gpiochip_unlock_as_irq is called, since an attempt to
switch the gpio direction for output will fail since gpiolib believes
that the gpio is in use for an interrupt and it does not know that it
the irq is actually disabled.
There are currently two drivers that would like to be able to do this:
the tda998x_drv.c driver where a regular gpio pin needs to be temporarily
reconfigured as an interrupt pin during CEC calibration, and the cec-gpio
driver where you want to configure the gpio pin as an interrupt while
waiting for traffic over the CEC bus, or as a regular pin when receiving or
transmitting a CEC message.
The solution is to add a new flag that is set when the irq is enabled,
and have gpiod_direction_output check for that flag.
We also add functions that drivers that do not use GPIOLIB_IRQCHIP
can call when they enable/disable the irq.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.
Mark gpio_suffixes array with __maybe_unused to hide a compiler warning:
In file included from
drivers/gpio/gpiolib-legacy.c:6:0:
drivers/gpio/gpiolib.h:95:27: warning: ‘gpio_suffixes’ defined but not used [-Wunused-const-variable=]
static const char * const gpio_suffixes[] = { "gpios", "gpio" };
^~~~~~~~~~~~~
In file included from drivers/gpio/gpiolib-devprop.c:17:0:
drivers/gpio/gpiolib.h:95:27: warning: ‘gpio_suffixes’ defined but not used [-Wunused-const-variable=]
static const char * const gpio_suffixes[] = { "gpios", "gpio" };
^~~~~~~~~~~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new challenge is to remove VLAs from the kernel
(see https://lkml.org/lkml/2018/3/7/621) to eventually
turn on -Wvla.
Using a kmalloc array is the easy way to fix this but kmalloc is still
more expensive than stack allocation. Introduce a fast path with a
fixed size stack array to cover most chip with gpios below some fixed
amount. The slow path dynamically allocates an array to cover those
chips with a large number of gpios.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Reviewed-and-tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are forward-declaring enum gpiod_flags, but this is not referenced
by pointer, it is a real struct member, so we need to actually include
it to compile anything including the local gpiolib.h header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Disallow open drain and open source flags to be set
simultaneously. This doesn't make electrical sense, and would
the hardware actually respond to this setting, the result
would be short circuit.
- ACPI GPIO has a new core infrastructure for handling quirks.
The quirks are there to deal with broken ACPI tables centrally
instead of pushing the work to individual drivers. In the world
of BIOS writers, the ACPI tables are perfect. Until they find a
mistake in it. When such a mistake is found, we can patch it
with a quirk. It should never happen, the problem is that it
happens. So we accomodate for it.
- Several documentation updates.
- Revert the patch setting up initial direction state from
reading the device. This was causing bad things for drivers
that can't read status on all its pins. It is only affecting
debugfs information quality.
- Label descriptors with the device name if no explicit label is
passed in.
- Pave the ground for transitioning SPI and regulators to use
GPIO descriptors by implementing some quirks in the device tree
GPIO parsing code.
New drivers:
- New driver for the Access PCIe IDIO 24 family.
Other:
- Major refactorings and improvements to the GPIO mockup driver
used for test and verification.
- Moved the AXP209 driver over to pin control since it gained a
pin control back-end. These patches will appear (with the same
hashes) in the pin control pull request as well.
- Convert the onewire GPIO driver w1-gpio to use descriptors.
This is merged here since the W1 maintainers send very few
pull requests and he ACKed it.
- Start to clean up driver headers using <linux/gpio.h> to just
use <linux/gpio/driver.h> as appropriate.
-----BEGIN PGP SIGNATURE-----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=k5nL
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"The is the bulk of GPIO changes for the v4.16 kernel cycle. It is
pretty calm this time around I think. I even got time to get to things
like starting to clean up header includes.
Core changes:
- Disallow open drain and open source flags to be set simultaneously.
This doesn't make electrical sense, and would the hardware actually
respond to this setting, the result would be short circuit.
- ACPI GPIO has a new core infrastructure for handling quirks. The
quirks are there to deal with broken ACPI tables centrally instead
of pushing the work to individual drivers. In the world of BIOS
writers, the ACPI tables are perfect. Until they find a mistake in
it. When such a mistake is found, we can patch it with a quirk. It
should never happen, the problem is that it happens. So we
accomodate for it.
- Several documentation updates.
- Revert the patch setting up initial direction state from reading
the device. This was causing bad things for drivers that can't read
status on all its pins. It is only affecting debugfs information
quality.
- Label descriptors with the device name if no explicit label is
passed in.
- Pave the ground for transitioning SPI and regulators to use GPIO
descriptors by implementing some quirks in the device tree GPIO
parsing code.
New drivers:
- New driver for the Access PCIe IDIO 24 family.
Other:
- Major refactorings and improvements to the GPIO mockup driver used
for test and verification.
- Moved the AXP209 driver over to pin control since it gained a pin
control back-end. These patches will appear (with the same hashes)
in the pin control pull request as well.
- Convert the onewire GPIO driver w1-gpio to use descriptors. This is
merged here since the W1 maintainers send very few pull requests
and he ACKed it.
- Start to clean up driver headers using <linux/gpio.h> to just use
<linux/gpio/driver.h> as appropriate"
* tag 'gpio-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (103 commits)
gpio: Timestamp events in hardirq handler
gpio: Fix kernel stack leak to userspace
gpio: Fix a documentation spelling mistake
gpio: Documentation update
gpiolib: remove redundant initialization of pointer desc
gpio: of: Fix NPE from OF flags
gpio: stmpe: Delete an unnecessary variable initialisation in stmpe_gpio_probe()
gpio: stmpe: Move an assignment in stmpe_gpio_probe()
gpio: stmpe: Improve a size determination in stmpe_gpio_probe()
gpio: stmpe: Use seq_putc() in stmpe_dbg_show()
gpio: No NULL owner
gpio: stmpe: i2c transfer are forbiden in atomic context
gpio: davinci: Include proper header
gpio: da905x: Include proper header
gpio: cs5535: Include proper header
gpio: crystalcove: Include proper header
gpio: bt8xx: Include proper header
gpio: bcm-kona: Include proper header
gpio: arizona: Include proper header
gpio: amd8111: Include proper header
...
We have been holding back on adding an API for fetching GPIO handles
directly from device nodes, strongly preferring to get it from the
spawn devices instead.
The fwnode interface however already contains an API for doing this,
as it is used for opaque device tree nodes or ACPI nodes for getting
handles to LEDs and keys that use GPIO: those are specified as one
child per LED/key in the device tree and are not individual devices.
However regulators present a special problem as they already have
helper functions to traverse the device tree from a regulator node
and two levels down to fill in data, and as it already traverses
GPIO nodes in its own way, and already holds a pointer to each
regulators device tree node, it makes most sense to export an
API to fetch the GPIO descriptor directly from the node.
We only support the devm_* version for now, hopefully no non-devres
version will be needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Following commit 9427ecbed4 ("gpio: Rework of_gpiochip_set_names()
to use device property accessors"), "gpio-line-names" DT property is
not retrieved anymore when chip->parent is not set by the driver.
This is due to OF based property reads having been replaced by device
based property reads.
This patch fixes that by making use of
fwnode_property_read_string_array() instead of
device_property_read_string_array() and handing over either
of_fwnode_handle(chip->of_node) or dev_fwnode(chip->parent)
to that function.
Fixes: 9427ecbed4 ("gpio: Rework of_gpiochip_set_names() to use device property accessors")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This string is never modified. Make it const.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
General support for state persistence is added to gpiolib with the
introduction of a new pinconf parameter to propagate the request to
hardware. The existing persistence support for sleep is adapted to
include hardware support if the GPIO driver provides it. Persistence
continues to be enabled by default; in-kernel consumers can opt out, but
userspace (currently) does not have a choice.
The *_SLEEP_MAY_LOSE_VALUE and *_SLEEP_MAINTAIN_VALUE symbols are
renamed, dropping the SLEEP prefix to reflect that the concept is no
longer sleep-specific. I feel that renaming to just *_MAY_LOSE_VALUE
could initially be misinterpreted, so I've further changed the symbols
to *_TRANSITORY and *_PERSISTENT to address this.
The sysfs interface is modified only to keep consistency with the
chardev interface in enforcing persistence for userspace exports.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some broken ACPI tables might require quirks in the OS.
Introduce quirks field in struct acpi_gpio_mapping.
Propagate them to struct acpi_gpio_info for further use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have the duplicated debug strings printed whenever
acpi_gpio_update_gpiod_flags() fails. Instead of doing this by callers,
move the debug output inside function.
In one case convert almost useless pr_debug() to dev_dbg() where
actual consumer of GPIO resource is disclosed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The further improvements are based on this change since
struct acpi_gpio_lookup is not available in some cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Literally.
I expect "lose" was meant here, rather than "loose", though you could feasibly
use a somewhat uncommon definition of "loose" to mean what would be meant by
"lose": "Loose the hounds" for instance, as in "Release the hounds".
Substituting in "value" for "hounds" gives "release the value", and makes some
sense, but futher substituting back to loose gives "loose the value" which
overall just seems a bit anachronistic.
Instead, use modern, pragmatic English and save a character.
Cc: Russell Currey <ruscur@russell.cc>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SPI-attached GPIO controllers typically read out all inputs in one go.
If callers desire the values of multipe inputs, ideally a single readout
should take place to return the desired values. However the current
driver API only offers a ->get callback but no ->get_multiple (unlike
->set_multiple, which is present). Thus, to read multiple inputs, a
full readout needs to be performed for every single value (barring
driver-internal caching), which is inefficient.
In fact, the lack of a ->get_multiple callback has been bemoaned
repeatedly by the gpio subsystem maintainer:
http://www.spinics.net/lists/linux-gpio/msg10571.htmlhttp://www.spinics.net/lists/devicetree/msg121734.html
Introduce the missing callback. Add corresponding consumer functions
such as gpiod_get_array_value(). Amend linehandle_ioctl() to take
advantage of the newly added infrastructure. Update the documentation.
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows ACPI GPIO code to modify flags based on
ACPI GpioIo() / GpioInt() resources.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is preparatory patch for enabling GPIO ACPI to configure a pin
accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add new flags to allow users to specify that they are not concerned with
the status of GPIOs whilst in a sleep/low power state.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It seems the code had been changed, but description left untouched.
Update description of the struct acpi_gpio_info and relative comments
accordingly.
Fixes: commit 52044723cd ("ACPI / gpio: Add irq_type when a GPIO is used as an interrupt")
Cc: Christophe RICARD <christophe.ricard@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to use "gpio-line-names" property in systems not having DT as
their boot firmware, rework of_gpiochip_set_names() to use device property
accessors. This reworked function is placed in a separate file making it
clear it deals with universal device properties.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_get_named_gpiod_flags() was missing a static inline version
when compiling without OF_GPIO. Add this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_gpiochip_add() and of_gpiochip_remove() are only used locally
in the gpio subsystem so move these functions to the local
header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic GPIO library directly implement code for acpi_find_gpio()
which is only used with CONFIG_ACPI. This was probably done because
OF did the same thing, but I removed that so remove this too.
Rename the internal acpi_find_gpio() in gpiolib-acpi.c to
acpi_populate_gpio_lookup() which seems to be more appropriate anyway
so as to avoid a namespace clash with the same function.
Make the stub return -ENOENT rather than -ENOSYS (as that is for
syscalls!).
For some reason the sunxi pin control driver was including the private
gpiolib header, it works just fine without it so remove that oneliner.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
