When the swdev device learns a new mac/vlan on a port, it sends some async
notification to the driver and the driver installs an FDB in the device.
To give a holistic system view, the learned mac/vlan should be reflected
in the bridge's FBD table, so the user, using normal iproute2 cmds, can view
what is currently learned by the device. This API on the bridge driver gives
a way for the swdev driver to install an FBD entry in the bridge FBD table.
(And remove one).
This is equivalent to the device running these cmds:
bridge fdb [add|del] <mac> dev <dev> vid <vlan id> master
This patch needs some extra eyeballs for review, in paricular around the
locking and contexts.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To notify switch driver of change in STP state of bridge port, add new
.ndo op and provide switchdev wrapper func to call ndo op. Use it in bridge
code then.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevice represents a port in a switch, it will expose
IFLA_PHYS_SWITCH_ID value via rtnl. Two netdevices with the same value
belong to one physical switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this is to provide a possibility to support various switch
chips. Drivers should implement relevant ndos to do so. Now there is
only one ndo defined:
- for getting physical switch id is in place.
Note that user can use random port netdevice to access the switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So this can be reused for identification of other "items" as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some Staging and IIO driver fixes for 3.18-rc7 that resolve a
number of reported issues, and a new device id for a staging wireless
driver.
All of these have been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlR4+R4ACgkQMUfUDdst+ynr6ACgwT/lNLkrC9it9f46Wzlrx+G7
vH0An1OPrgAGjpiu8LYou1CpzsJkMTAq
=3+bs
-----END PGP SIGNATURE-----
Merge tag 'staging-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are some staging and IIO driver fixes for 3.18-rc7 that resolve a
number of reported issues, and a new device id for a staging wireless
driver.
All of these have been in linux-next"
* tag 'staging-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Add new device ID for DLink GO-USB-N150
staging: r8188eu: Fix scheduling while atomic error introduced in commit fadbe0cd
iio: accel: bmc150: set low default thresholds
iio: accel: bmc150: Fix iio_event_spec direction
iio: accel: bmc150: Send x, y and z motion separately
iio: accel: bmc150: Error handling when mode set fails
iio: gyro: bmg160: Fix iio_event_spec direction
iio: gyro: bmg160: Send x, y and z motion separately
iio: gyro: bmg160: Don't let interrupt mode to be open drain
iio: gyro: bmg160: Error handling when mode set fails
iio: adc: men_z188_adc: Add terminating entry for men_z188_ids
iio: accel: kxcjk-1013: Fix kxcjk10013_set_range
iio: Fix IIO_EVENT_CODE_EXTRACT_DIR bit mask
No excitement, here are only minor fixes: an endian fix for the
new DSD format we added in 3.18, a fix for HP mute LED, and a
fix for Native Instrument quirk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=azkh
-----END PGP SIGNATURE-----
Merge tag 'sound-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"No excitement, here are only minor fixes: an endian fix for the new
DSD format we added in 3.18, a fix for HP mute LED, and a fix for
Native Instrument quirk"
* tag 'sound-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Add big-endian DSD sample formats and fix XMOS DSD sample format
ALSA: hda - One more HP machine needs to change mute led quirk
ALSA: usb-audio: Use snd_usb_ctl_msg() for Native Instruments quirk
Pull networking fixes from David Miller:
"Several small fixes here:
1) Don't crash in tg3 driver when the number of tx queues has been
configured to be different from the number of rx queues. From
Thadeu Lima de Souza Cascardo.
2) VLAN filter not disabled properly in promisc mode in ixgbe driver,
from Vlad Yasevich.
3) Fix OOPS on dellink op in VTI tunnel driver, from Xin Long.
4) IPV6 GRE driver WCCP code checks skb->protocol for ETH_P_IP
instead of ETH_P_IPV6, whoops. From Yuri Chislov.
5) Socket matching in ping driver is buggy when packet AF does not
match socket's AF. Fix from Jane Zhou.
6) Fix checksum calculation errors in VXLAN due to where the
udp_tunnel6_xmit_skb() helper gets it's saddr/daddr from. From
Alexander Duyck.
7) Fix 5G detection problem in rtlwifi driver, from Larry Finger.
8) Fix NULL deref in tcp_v{4,6}_send_reset, from Eric Dumazet.
9) Various missing netlink attribute verifications in bridging code,
from Thomas Graf.
10) tcp_recvmsg() unconditionally calls ipv4 ip_recv_error even for
ipv6 sockets, whoops. Fix from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net-timestamp: make tcp_recvmsg call ipv6_recv_error for AF_INET6 socks
bridge: Sanitize IFLA_EXT_MASK for AF_BRIDGE:RTM_GETLINK
bridge: Add missing policy entry for IFLA_BRPORT_FAST_LEAVE
net: Check for presence of IFLA_AF_SPEC
net: Validate IFLA_BRIDGE_MODE attribute length
bridge: Validate IFLA_BRIDGE_FLAGS attribute length
stmmac: platform: fix default values of the filter bins setting
net/mlx4_core: Limit count field to 24 bits in qp_alloc_res
net: dsa: bcm_sf2: reset switch prior to initialization
net: dsa: bcm_sf2: fix unmapping registers in case of errors
tg3: fix ring init when there are more TX than RX channels
tcp: fix possible NULL dereference in tcp_vX_send_reset()
rtlwifi: Change order in device startup
rtlwifi: rtl8821ae: Fix 5G detection problem
Revert "netfilter: conntrack: fix race in __nf_conntrack_confirm against get_next_corpse"
vxlan: Fix boolean flip in VXLAN_F_UDP_ZERO_CSUM6_[TX|RX]
ip6_udp_tunnel: Fix checksum calculation
net-timestamp: Fix a documentation typo
net/ping: handle protocol mismatching scenario
af_packet: fix sparse warning
...
TCP timestamping introduced MSG_ERRQUEUE handling for TCP sockets.
If the socket is of family AF_INET6, call ipv6_recv_error instead
of ip_recv_error.
This change is more complex than a single branch due to the loadable
ipv6 module. It reuses a pre-existing indirect function call from
ping. The ping code is safe to call, because it is part of the core
ipv6 module and always present when AF_INET6 sockets are active.
Fixes: 4ed2d765 (net-timestamp: TCP timestamping)
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
It may also be worthwhile to add WARN_ON_ONCE(sk->family == AF_INET6)
to ip_recv_error.
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of these are fairly standard little fixes, a bmc150 and bmg160 patch
is to make an ABI change to indicated a specific axis in an event rather
than the generic option in the original drivers. As both of these drivers
are new in this cycle it would be ideal to push this minor change through
even though it isn't strictly a fix. A couple of other 'fixes' change
defaults for some settings on these new drivers to more intuitive calues.
Looks like some useful feedback has been coming in for this driver
since it was applied.
* IIO_EVENT_CODE_EXTRACT_DIR bit mask was wrong and has been for a while
0xCF clearly doesn't give a contiguous bitmask.
* kxcjk-1013 range setting was failing to mask out the previous value
in the register and hence was 'enable only'.
* men_z188 device id table wasn't null terminated.
* bmg160 and bmc150 both failed to correctly handling an error in mode
setting.
* bmg160 and bmc150 both had a bug in setting the event direction in the
event spec (leads to an attribute name being incorrect)
* bmg160 defaulted to an open drain output for the interrupt - as a default
this obviously only works with some interrupt chips - hence change the
default to push-pull (note this is a new driver so we aren't going to
cause any regressions with this change).
* bmc150 had an unintuitive default for the rate of change (motion detector)
so change it to 0 (new driver so change of default won't cause any
regressions).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IPMl
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.18c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Third set of IIO fixes for the 3.18 cycle.
Most of these are fairly standard little fixes, a bmc150 and bmg160 patch
is to make an ABI change to indicated a specific axis in an event rather
than the generic option in the original drivers. As both of these drivers
are new in this cycle it would be ideal to push this minor change through
even though it isn't strictly a fix. A couple of other 'fixes' change
defaults for some settings on these new drivers to more intuitive calues.
Looks like some useful feedback has been coming in for this driver
since it was applied.
* IIO_EVENT_CODE_EXTRACT_DIR bit mask was wrong and has been for a while
0xCF clearly doesn't give a contiguous bitmask.
* kxcjk-1013 range setting was failing to mask out the previous value
in the register and hence was 'enable only'.
* men_z188 device id table wasn't null terminated.
* bmg160 and bmc150 both failed to correctly handling an error in mode
setting.
* bmg160 and bmc150 both had a bug in setting the event direction in the
event spec (leads to an attribute name being incorrect)
* bmg160 defaulted to an open drain output for the interrupt - as a default
this obviously only works with some interrupt chips - hence change the
default to push-pull (note this is a new driver so we aren't going to
cause any regressions with this change).
* bmc150 had an unintuitive default for the rate of change (motion detector)
so change it to 0 (new driver so change of default won't cause any
regressions).
This function does the work to update a checksum field as part of
remote checksum offload.
remcsum_adjust does the following:
1) Subtract out the calculated checksum from the beginning of the
packet (ptr arg) to the start offset.
2) Adjust the checksum field indicated by offset based on the modified
checksum value from above step.
3) Return the difference in the old checksum field value and the
new one. The caller will use this to update skb->csum and NAPI csum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 85c8555ff0 ("KVM: check for !is_zero_pfn() in
kvm_is_mmio_pfn()") and renames the function to kvm_is_reserved_pfn.
The problem being addressed by the patch above was that some ARM code
based the memory mapping attributes of a pfn on the return value of
kvm_is_mmio_pfn(), whose name indeed suggests that such pfns should
be mapped as device memory.
However, kvm_is_mmio_pfn() doesn't do quite what it says on the tin,
and the existing non-ARM users were already using it in a way which
suggests that its name should probably have been 'kvm_is_reserved_pfn'
from the beginning, e.g., whether or not to call get_page/put_page on
it etc. This means that returning false for the zero page is a mistake
and the patch above should be reverted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull powerpc fixes from Ben Herrenschmidt:
"This series fix a nasty issue with radeon adapters on powerpc servers,
it's all CC'ed stable and has the relevant maintainers ack's/reviews.
Basically, some (radeon) adapters have issues with MSI addresses above
1T (only support 40-bits). We had powerpc specific quirk but it only
listed a specific revision of an adapter that we shipped with our
machines and didn't properly handle the audio function which some
distros enable nowadays.
So we made the quirk generic and fixed both the graphic and audio
drivers properly to use it.
Without that, ppc64 server machines will crash at boot with a radeon
adapter.
Note: This has been brewing for a while, it just needed a last respin
which got delayed due to us moving ozlabs to a new location in town
and other such things taking priority"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pci: Remove unused force_32bit_msi quirk
powerpc/pseries: Honor the generic "no_64bit_msi" flag
powerpc/powernv: Honor the generic "no_64bit_msi" flag
sound/radeon: Move 64-bit MSI quirk from arch to driver
gpu/radeon: Set flag to indicate broken 64-bit MSI
PCI/MSI: Add device flag indicating that 64-bit MSIs don't work
ALSA: hda - Limit 40bit DMA for AMD HDMI controllers
single fix in one of the basic clock templates. No fixes to the core
this time around. As with most clock driver fixes these run the gamut
from fixing a build warning to fixing wrecked memory timings, with a
little USB tossed in for fun. Please consider pulling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4O2k
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of https://git.linaro.org/people/mike.turquette/linux
Pull clock fixes from Mike Turquette:
"The fixes for the clock framework are all regressions in drivers, plus
a single fix in one of the basic clock templates. No fixes to the
core this time around.
As with most clock driver fixes these run the gamut from fixing a
build warning to fixing wrecked memory timings, with a little USB
tossed in for fun"
* tag 'clk-fixes-for-linus' of https://git.linaro.org/people/mike.turquette/linux:
clk: pxa: fix pxa27x CCCR bit usage
clk-divider: Fix READ_ONLY when divider > 1
clk: qcom: Fix duplicate rbcpr clock name
clk: at91: usb: fix at91sam9x5 recalc, round and set rate
clk: at91: usb: fix at91rm9200 round and set rate
tipc_netlink.h is the user-space header for the new netlink api. It
was accidentally left out of the uapi Kbuild list when the api was
added.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should be u16. So fix it to kill the sparse warning.
Fixes: c7e2b9689e "sched: introduce vlan action"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter/ipvs updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, this includes the NAT redirection support for nf_tables, the
cgroup support for nft meta and conntrack zone support for the connlimit
match. Coming after those, a bunch of sparse warning fixes, missing
netns bits and cleanups. More specifically, they are:
1) Prepare IPv4 and IPv6 NAT redirect code to use it from nf_tables,
patches from Arturo Borrero.
2) Introduce the nf_tables redir expression, from Arturo Borrero.
3) Remove an unnecessary assignment in ip_vs_xmit/__ip_vs_get_out_rt().
Patch from Alex Gartrell.
4) Add nft_log_dereference() macro to the nf_log infrastructure, patch
from Marcelo Leitner.
5) Add some extra validation when registering logger families, also
from Marcelo.
6) Some spelling cleanups from stephen hemminger.
7) Fix sparse warning in nf_logger_find_get().
8) Add cgroup support to nf_tables meta, patch from Ana Rey.
9) A Kconfig fix for the new redir expression and fix sparse warnings in
the new redir expression.
10) Fix several sparse warnings in the netfilter tree, from
Florian Westphal.
11) Reduce verbosity when OOM in nfnetlink_log. User can basically do
nothing when this situation occurs.
12) Add conntrack zone support to xt_connlimit, again from Florian.
13) Add netnamespace support to the h323 conntrack helper, contributed
by Vasily Averin.
14) Remove unnecessary nul-pointer checks before free_percpu() and
module_put(), from Markus Elfring.
15) Use pr_fmt in nfnetlink_log, again patch from Marcelo Leitner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is very similar to the macvlan driver except that it
uses L3 on the frame to determine the logical interface while
functioning as packet dispatcher. It inherits L2 of the master
device hence the packets on wire will have the same L2 for all
the packets originating from all virtual devices off of the same
master device.
This driver was developed keeping the namespace use-case in
mind. Hence most of the examples given here take that as the
base setup where main-device belongs to the default-ns and
virtual devices are assigned to the additional namespaces.
The device operates in two different modes and the difference
in these two modes in primarily in the TX side.
(a) L2 mode : In this mode, the device behaves as a L2 device.
TX processing upto L2 happens on the stack of the virtual device
associated with (namespace). Packets are switched after that
into the main device (default-ns) and queued for xmit.
RX processing is simple and all multicast, broadcast (if
applicable), and unicast belonging to the address(es) are
delivered to the virtual devices.
(b) L3 mode : In this mode, the device behaves like a L3 device.
TX processing upto L3 happens on the stack of the virtual device
associated with (namespace). Packets are switched to the
main-device (default-ns) for the L2 processing. Hence the routing
table of the default-ns will be used in this mode.
RX processins is somewhat similar to the L2 mode except that in
this mode only Unicast packets are delivered to the virtual device
while main-dev will handle all other packets.
The devices can be added using the "ip" command from the iproute2
package -
ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This can be set by quirks/drivers to be used by the architecture code
that assigns the MSI addresses.
We additionally add verification in the core MSI code that the values
assigned by the architecture do satisfy the limitation in order to fail
gracefully if they don't (ie. the arch hasn't been updated to deal with
that quirk yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Pull percpu fix from Tejun Heo:
"This contains one patch to fix a race condition which can lead to
percpu_ref using a percpu pointer which is corrupted with a set DEAD
bit. The bug was introduced while separating out the ATOMIC mode flag
from the DEAD flag. The fix is pretty straight forward.
I just committed the patch to the percpu tree but am sending out the
pull request early as I'll be on vacation for a week. The patch
should be fairly safe and while the latency will be higher I'll be
checking emails"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu-ref: fix DEAD flag contamination of percpu pointer
While decoupling ATOMIC and DEAD flags, f47ad45784 ("percpu_ref:
decouple switching to percpu mode and reinit") updated
__ref_is_percpu() so that it only tests ATOMIC flag to determine
whether the ref is in percpu mode or not; however, while DEAD implies
ATOMIC, the two flags are set separately during percpu_ref_kill() and
if __ref_is_percpu() races percpu_ref_kill(), it may see DEAD w/o
ATOMIC. Because __ref_is_percpu() returns @ref->percpu_count_ptr
value verbatim as the percpu pointer after testing ATOMIC, the pointer
may now be contaminated with the DEAD flag.
This can be fixed by clearing the flag bits before returning the
pointer which was the fix proposed by Shaohua; however, as DEAD
implies ATOMIC, we can just test for both flags at once and avoid the
explicit masking.
Update __ref_is_percpu() so that it tests that both ATOMIC and DEAD
are clear before returning @ref->percpu_count_ptr as the percpu
pointer.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-Reviewed-by: Shaohua Li <shli@kernel.org>
Link: http://lkml.kernel.org/r/995deb699f5b873c45d667df4add3b06f73c2c25.1416638887.git.shli@kernel.org
Fixes: f47ad45784 ("percpu_ref: decouple switching to percpu mode and reinit")
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix BUG when decrypting empty packets in mac80211, from Ronald Wahl.
2) nf_nat_range is not fully initialized and this is copied back to
userspace, from Daniel Borkmann.
3) Fix read past end of b uffer in netfilter ipset, also from Dan
Carpenter.
4) Signed integer overflow in ipv4 address mask creation helper
inet_make_mask(), from Vincent BENAYOUN.
5) VXLAN, be2net, mlx4_en, and qlcnic need ->ndo_gso_check() methods to
properly describe the device's capabilities, from Joe Stringer.
6) Fix memory leaks and checksum miscalculations in openvswitch, from
Pravin B SHelar and Jesse Gross.
7) FIB rules passes back ambiguous error code for unreachable routes,
making behavior confusing for userspace. Fix from Panu Matilainen.
8) ieee802154fake_probe() doesn't release resources properly on error,
from Alexey Khoroshilov.
9) Fix skb_over_panic in add_grhead(), from Daniel Borkmann.
10) Fix access of stale slave pointers in bonding code, from Nikolay
Aleksandrov.
11) Fix stack info leak in PPP pptp code, from Mathias Krause.
12) Cure locking bug in IPX stack, from Jiri Bohac.
13) Revert SKB fclone memory freeing optimization that is racey and can
allow accesses to freed up memory, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (71 commits)
tcp: Restore RFC5961-compliant behavior for SYN packets
net: Revert "net: avoid one atomic operation in skb_clone()"
virtio-net: validate features during probe
cxgb4 : Fix DCB priority groups being returned in wrong order
ipx: fix locking regression in ipx_sendmsg and ipx_recvmsg
openvswitch: Don't validate IPv6 label masks.
pptp: fix stack info leak in pptp_getname()
brcmfmac: don't include linux/unaligned/access_ok.h
cxgb4i : Don't block unload/cxgb4 unload when remote closes TCP connection
ipv6: delete protocol and unregister rtnetlink when cleanup
net/mlx4_en: Add VXLAN ndo calls to the PF net device ops too
bonding: fix curr_active_slave/carrier with loadbalance arp monitoring
mac80211: minstrel_ht: fix a crash in rate sorting
vxlan: Inline vxlan_gso_check().
can: m_can: update to support CAN FD features
can: m_can: fix incorrect error messages
can: m_can: add missing delay after setting CCCR_INIT bit
can: m_can: fix not set can_dlc for remote frame
can: m_can: fix possible sleep in napi poll
can: m_can: add missing message RAM initialization
...
This batch ended up as a relatively high volume due to pending
ASoC fixes. But most of fixes there are trivial and/or device-
specific fixes and quirks, so safe to apply. The only (ASoC)
core fixes are the DPCM race fix and the machine-driver matching
fix for componentization.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=oc6T
-----END PGP SIGNATURE-----
Merge tag 'sound-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This batch ended up as a relatively high volume due to pending ASoC
fixes. But most of fixes there are trivial and/or device- specific
fixes and quirks, so safe to apply. The only (ASoC) core fixes are
the DPCM race fix and the machine-driver matching fix for
componentization"
* tag 'sound-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - fix the mic mute led problem for Latitude E5550
ALSA: hda - move DELL_WMI_MIC_MUTE_LED to the tail in the quirk chain
ASoC: wm_adsp: Avoid attempt to free buffers that might still be in use
ALSA: usb-audio: Set the Control Selector to SU_SELECTOR_CONTROL for UAC2
ALSA: usb-audio: Add ctrl message delay quirk for Marantz/Denon devices
ASoC: sgtl5000: Fix SMALL_POP bit definition
ASoC: cs42l51: re-hook of_match_table pointer
ASoC: rt5670: change dapm routes of PLL connection
ASoC: rt5670: correct the incorrect default values
ASoC: samsung: Add MODULE_DEVICE_TABLE for Snow
ASoC: max98090: Correct pclk divisor settings
ASoC: dpcm: Fix race between FE/BE updates and trigger
ASoC: Fix snd_soc_find_dai() matching component by name
ASoC: rsnd: remove unsupported PAUSE flag
ASoC: fsi: remove unsupported PAUSE flag
ASoC: rt5645: Mark RT5645_TDM_CTRL_3 as readable
ASoC: rockchip-i2s: fix infinite loop in rockchip_snd_rxctrl
ASoC: es8328-i2c: Fix i2c_device_id name field in es8328_id
ASoC: fsl_asrc: Add reg_defaults for regmap to fix kernel dump
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: two NUMA fixes, two cputime fixes and an RCU/lockdep fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cputime: Fix clock_nanosleep()/clock_gettime() inconsistency
sched/cputime: Fix cpu_timer_sample_group() double accounting
sched/numa: Avoid selecting oneself as swap target
sched/numa: Fix out of bounds read in sched_init_numa()
sched: Remove lockdep check in sched_move_task()
Pull core fix from Ingo Molnar:
"Fix GENMASK macro shift overflow"
Nobody seems to currently use GENMASK() to fill every single last bit
(which is what overflows) in-tree, and gcc would warn about it, so we
have that going for us. But apparently there are pending changes that
want this.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
bitops: Fix shift overflow in GENMASK macros
John W. Linville says:
====================
pull request: wireless-next 2014-11-21
Please pull this batch of updates intended for the 3.19 stream...
For the mac80211 bits, Johannes says:
"It has been a while since my last pull request, so we accumulated
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people"
For the Bluetooth bits, Johan says:
"Here's another set of patches for 3.19. Most of it is again fixes and
cleanups to ieee802154 related code from Alexander Aring. We've also got
better handling of hardware error events along with a proper API for HCI
drivers to notify the HCI core of such situations. There's also a minor
fix for mgmt events as well as a sparse warning fix. The code for
sending HCI commands synchronously also gets a fix where we might loose
the completion event in the case of very fast HW (particularly easily
reproducible with an emulated HCI device)."
And...
"Here's another bluetooth-next pull request for 3.19. We've got:
- Various fixes, cleanups and improvements to ieee802154/mac802154
- Support for a Broadcom BCM20702A1 variant
- Lots of lockdep fixes
- Fixed handling of LE CoC errors that should trigger SMP"
For the Atheros bits, Kalle says:
"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:
o fix resume (Bartosz)
o firmware restart is now faster and more reliable (Michal)
o it's now possible to test hardware restart functionality without
crashing the firmware using hw-restart parameter with
simulate_fw_crash debugfs file (Michal)"
On top of that...both ath9k and mwifiex get their usual level of
updates. Of note is the ath9k spectral scan work from Oleksij Rempel.
I also pulled from the wireless tree in order to avoid some merge issues.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NAME_TABLE_GET command to the new tipc netlink API.
This command supports dumping the name table of all nodes.
Netlink logical layout of name table response message:
-> name table
-> publication
-> type
-> lower
-> upper
-> scope
-> node
-> ref
-> key
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NET_SET command to the new tipc netlink API.
This command can set the network id and network (tipc) address.
Netlink logical layout of network set message:
-> net
[ -> id ]
[ -> address ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NET_GET command to the new tipc netlink API.
This command dumps the network id of the node.
Netlink logical layout of returned network data:
-> net
-> id
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NODE_GET to the new tipc netlink API.
This command can dump the address and node status of all nodes in the
tipc cluster.
Netlink logical layout of returned node/address data:
-> node
-> address
-> up flag
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_MEDIA_SET command to the new tipc netlink API.
This command can set one or more link properties for a particular
media.
Netlink logical layout of bearer set message:
-> media
-> name
-> link properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_MEDIA_GET command to the new tipc netlink API.
This command supports dumping all information about all defined
media as well as getting all information about a specific media.
The information about a media includes name and link properties.
Netlink logical layout of media get response message:
-> media
-> name
-> link properties
-> tolerance
-> priority
-> window
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_LINK_RESET_STATS command to the new netlink API.
This command resets the link statistics for a particular link.
Netlink logical layout of link reset message:
-> link
-> name
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_LINK_SET to the new tipc netlink API.
This command can set one or more link properties for a particular
link.
Netlink logical layout of link set message:
-> link
-> name
-> properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_LINK_GET command to the new tipc netlink API.
This command supports dumping all information about all links
(including the broadcast link) or getting all information about a
specific link (not the broadcast link).
The information about a link includes name, transmission info,
properties and link statistics.
As the tipc broadcast link is special we unfortunately have to treat
it specially. It is a deliberate decision not to abstract the
broadcast link on this (API) level.
Netlink logical layout of link response message:
-> port
-> name
-> MTU
-> RX
-> TX
-> up flag
-> active flag
-> properties
-> priority
-> tolerance
-> window
-> statistics
-> rx_info
-> rx_fragments
-> rx_fragmented
-> rx_bundles
-> rx_bundled
-> tx_info
-> tx_fragments
-> tx_fragmented
-> tx_bundles
-> tx_bundled
-> msg_prof_tot
-> msg_len_cnt
-> msg_len_tot
-> msg_len_p0
-> msg_len_p1
-> msg_len_p2
-> msg_len_p3
-> msg_len_p4
-> msg_len_p5
-> msg_len_p6
-> rx_states
-> rx_probes
-> rx_nacks
-> rx_deferred
-> tx_states
-> tx_probes
-> tx_nacks
-> tx_acks
-> retransmitted
-> duplicates
-> link_congs
-> max_queue
-> avg_queue
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_PUBL_GET command to the new tipc netlink API.
This command supports dumping of all publications for a specific
socket.
Netlink logical layout of request message:
-> socket
-> reference
Netlink logical layout of response message:
-> publication
-> type
-> lower
-> upper
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
