Commit Graph

136 Commits

Author SHA1 Message Date
Raul E Rangel
9e4be8d03f mmc: core: Verify SD bus width
The SD Physical Layer Spec says the following: Since the SD Memory Card
shall support at least the two bus modes 1-bit or 4-bit width, then any SD
Card shall set at least bits 0 and 2 (SD_BUS_WIDTH="0101").

This change verifies the card has specified a bus width.

AMD SDHC Device 7806 can get into a bad state after a card disconnect
where anything transferred via the DATA lines will always result in a
zero filled buffer. Currently the driver will continue without error if
the HC is in this condition. A block device will be created, but reading
from it will result in a zero buffer. This makes it seem like the SD
device has been erased, when in actuality the data is never getting
copied from the DATA lines to the data buffer.

SCR is the first command in the SD initialization sequence that uses the
DATA lines. By checking that the response was invalid, we can abort
mounting the card.

Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-05-06 12:33:03 +02:00
hongjiefang
099b648116 mmc: core: Add a debug print when the card may have been replaced
If the card was removed in suspended state and a new one was inserted,
print a debug log when the check detects that it's not the old card.

Signed-off-by: hongjiefang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-28 09:28:27 +01:00
Avri Altman
bc47e2f6f9 mmc: core: Add discard support to sd
SD spec v5.1 adds discard support. The flows and commands are similar to
mmc, so just set the discard arg in CMD38.

A host which supports DISCARD shall check if the DISCARD_SUPPORT (b313)
is set in the SD_STATUS register.  If the card does not support discard,
the host shall not issue DISCARD command, but ERASE command instead.

Post the DISCARD operation, the card may de-allocate the discarded
blocks partially or completely. So the host mustn't make any assumptions
concerning the content of the discarded region. This is unlike ERASE
command, in which the region is guaranteed to contain either '0's or
'1's, depends on the content of DATA_STAT_AFTER_ERASE (b55) in the scr
register.

One more important difference compared to ERASE is the busy timeout
which we will address on the next patch.

Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-28 09:16:12 +01:00
Avri Altman
68539e2bc3 mmc: core: Indicate SD specs higher than 4.0
SD specs version 4.x and 5.x have a dedicated slices in the SCR register.
Higher versions will rely on a combination of the existing fields.

Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25 08:40:58 +01:00
Avri Altman
01904ff776 mmc: core: Calculate the discard arg only once
In MMC, the discard arg is a read-only ext_csd parameter - set it once
on card init. To be consistent, do that for SD as well even though its
discard arg is always 0x0.

Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25 08:40:58 +01:00
Ulf Hansson
3a3db6030b mmc: core: Rename ->reset() bus ops to ->hw_reset()
The bus ops ->reset() executes a full HW reset of the card, as the calling
function mmc_hw_reset() also indicates by its name. Let's convert to follow
the similar names, for both the bus ops callback and for the corresponding
bus ops functions, as to clarify the purpose of code.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:33:29 +02:00
Kyle Roeschley
247cfe5355 mmc: core: Add capability to avoid 3.3V signaling
Some SD host controllers cannot handle extended use of 3.3V signaling.
To accommodate these controllers, add a capability that requires us to
negotiate the voltage down from 3.3V during card initialization.

Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:44 +02:00
Harish Jenny K N
974e85e90c mmc: core: Export card RCA register via sysfs
This patch exports RCA register to sysfs which will help in reading the
disk identification information.

Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-15 14:43:05 +01:00
Shawn Lin
3715ce57f4 mmc: sd: Remove redundant err assignment from mmc_read_switch
Variable err would be firstly initialized by the return value of
mmc_sd_switch().

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-15 09:32:30 +01:00
Shawn Lin
d6743a8a1a mmc: core: Don't try UHS-I mode if 4-bit mode isn't supported
Per SD specification physical layer v4.0, section 3.9.4, it
says "UHS-I supports only 4-bit mode. Host shall select 4-bit
mode by ACMD6. However mmc_sd_init_uhs_card() still go ahead
to initialize the cards anyway, whether card or host won't
support 4-bit mode.

  This breaks the platforms which could support UHS-I mode but on
some certain boards only support 1-bit mode with a UHS-I card inserted,
as all the tuning process is broken due to this. Alternatively, we
should check the return value from mmc_set_bus_width() to see if host
could finish the request to switch the bus width on its side. But that
needs more thing to do than this patch that just bails out early to try
high speed mode if 4-bit mode isn't available for whatever reason. And
this patch could also fix the same problem for sdio since R4_18V_PRESENT
won't be set for ocr when mmc_sdio_init_card() finds mmc_host_uhs()
is false.

  Note that this patch doesn't keep the checking of card->scr.sda_spec3
and comparing card->scr.bus_widths with SD_SCR_BUS_WIDTH_4 within
mmc_sd_init_uhs_card() since if the sd cards response with SD_ROCR_S18A,
it definitely supports UHS-I mode, which implicitly means these checkings
are always true.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-15 09:30:39 +01:00
Bastian Stender
c892b0d817 mmc: core: prepend 0x to OCR entry in sysfs
The sysfs entry "ocr" was missing the 0x prefix to identify it as hex
formatted.

Fixes: 5fb06af7a3 ("mmc: core: Extend sysfs with OCR register")
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: <stable@vger.kernel.org> # v4.8+
[Ulf: Amended change to also cover SD-cards]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-11-29 10:46:53 +01:00
Adrian Hunter
6a11fc47f1 mmc: sd: Fix signal voltage when there is no power cycle
Some boards have SD card connectors where the power rail cannot be switched
off by the driver. However there are various circumstances when a card
might be re-initialized, such as after system resume, warm re-boot, or
error handling. However, a UHS card will continue to use 1.8V signaling
unless it is power cycled.

If the card has not been power cycled, it may still be using 1.8V
signaling. According to the SD spec., the Bus Speed Mode (function group 1)
bits 2 to 4 are zero if the card is initialized at 3.3V signal level. Thus
they can be used to determine if the card has already switched to 1.8V
signaling. Detect that situation and try to initialize a UHS-I (1.8V)
transfer mode.

Tested with the following cards:
  Transcend 4GB High Speed
  Kingston 64GB SDR104
  Lexar by Micron HIGH-PERFORMANCE 300x 16GB DDR50
  SanDisk Ultra 8GB DDR50
  Transcend Ultimate 600x 16GB SDR104
  Transcend Premium 300x 64GB SDR104
  Lexar by Micron Professional 1000x 32GB UHS-II SDR104
  SanDisk Extreme Pro 16GB SDR104

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Zhoujie Wu <zjwu@marvell.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-10-30 11:45:57 +01:00
Adrian Hunter
6c0cedd1ef mmc: core: Introduce host claiming by context
Currently the host can be claimed by a task.  Change this so that the host
can be claimed by a context that may or may not be a task.  This provides
for the host to be claimed by a block driver queue to support blk-mq, while
maintaining compatibility with the existing use of mmc_claim_host().

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-10-30 11:45:49 +01:00
Shawn Lin
4406ae215b mmc: core: correct taac parameter according to the specification
Per the spec of JESD84-B51, section 7.3, replace tacc with taac to
fix the obvious typo.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 14:01:46 +02:00
Ulf Hansson
a147373250 mmc: core: Re-factor code for sending CID
Instead of having the caller to check for SPI mode, let's leave that to
internals of mmc_send_cid(). In this way the code gets cleaner and it
becomes clear what is specific to SPI and non-SPI mode.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2017-06-20 10:30:45 +02:00
Markus Elfring
e1df7ae30b mmc: core: Delete error messages for failed memory allocations
Omit an extra message for memory allocation failures.

This issue was detected by using the Coccinelle software.

Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20 10:30:21 +02:00
Winkler, Tomas
06c9ccb78e mmc: core: add proper be32 annotation
Annotate big endian values correctly and make sparse happy.
In mmc_app_send_scr remove scr function parameter as it was
updating card->raw_scr anyway.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:42:19 +02:00
Ulf Hansson
2ed573b603 mmc: core: Clarify usage of mmc_set_signal_voltage()
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to
1.8V for UHS mode. To clarify this let's do the following changes.

- We are always providing MMC_SIGNAL_VOLTAGE_180 as the signal_voltage
  parameter to the function. Then, let's just remove the parameter as it
  serves no purpose.
- Rename the function to mmc_set_uhs_voltage().

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
2017-02-13 13:20:43 +01:00
Ulf Hansson
5857b29b96 mmc: core: Move public functions from host.h to private headers
A significant amount of functions are available through the public mmc
host.h header file. Let's slim down this public mmc interface, as to
prevent users from abusing it, by moving some of the functions to private
mmc host.h header file.

This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2017-02-13 13:20:25 +01:00
Ulf Hansson
4facdde113 mmc: core: Move public functions from card.h to private headers
A significant amount of functions and other definitions are available
through the public mmc card.h header file. Let's slim down this public mmc
interface, as to prevent users from abusing it, by moving some of the
functions/definitions to private mmc header files.

This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2017-02-13 13:20:24 +01:00
Paul Burton
e85baa8868 mmc: sd: Meet alignment requirements for raw_ssr DMA
The mmc_read_ssr() function results in DMA to the raw_ssr member of
struct mmc_card, which is not guaranteed to be cache line aligned & thus
might not meet the requirements set out in Documentation/DMA-API.txt:

  Warnings:  Memory coherency operates at a granularity called the cache
  line width.  In order for memory mapped by this API to operate
  correctly, the mapped region must begin exactly on a cache line
  boundary and end exactly on one (to prevent two separately mapped
  regions from sharing a single cache line).  Since the cache line size
  may not be known at compile time, the API will not enforce this
  requirement.  Therefore, it is recommended that driver writers who
  don't take special care to determine the cache line size at run time
  only map virtual regions that begin and end on page boundaries (which
  are guaranteed also to be cache line boundaries).

On some systems where DMA is non-coherent this can lead to us losing
data that shares cache lines with the raw_ssr array.

Fix this by kmalloc'ing a temporary buffer to perform DMA into. kmalloc
will ensure the buffer is suitably aligned, allowing the DMA to be
performed without any loss of data.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 5275a652d2 ("mmc: sd: Export SD Status via “ssr” device attribute")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-21 08:34:30 +01:00
Shawn Lin
349583d666 mmc: core: remove BUG_ONs from sd
BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-05 10:31:10 +01:00
Uri Yanai
5275a652d2 mmc: sd: Export SD Status via “ssr” device attribute
The SD Status register contains several important fields related to the
SD Card proprietary features.
Those fields may be used by user space applications for vendor specific
usage.
None of those fields are exported today by the driver to user space.
In this patch, we are reading the SD Status register and exporting
(using MMC_DEV_ATTR) the SD Status register to the user space.

Signed-off-by: Uri Yanai <uri.yanai@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-09-26 21:31:09 +02:00
Bojan Prtvar
6825a60658 mmc: core: Extend sysfs with DSR register
Export DSR register through sysfs same as we did for the CID, CSD and
OCR registers.

Signed-off-by: Bojan Prtvar <prtvar.b@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:51 +02:00
Bojan Prtvar
5fb06af7a3 mmc: core: Extend sysfs with OCR register
Registers CID and CSD are already exported through sysfs so let's make
this interface complete by adding missing OCR register.

Signed-off-by: Bojan Prtvar <prtvar.b@gmail.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:48 +02:00
Shawn Lin
0076c71e37 mmc: core: remove redundant memset of mmc_decode_cid
When initializing sd or sdio card, we get struct mmc_card
from mmc_alloc_card which allocates it by kzalloc. So we don't
need another memset while decoding cid.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-03-17 14:54:41 +01:00
Carlo Caione
e10c321977 mmc: core: Enable tuning according to the actual timing
While in sdhci_execute_tuning() the choice whether or not to enable the
tuning is done on the actual timing, in the mmc_sdio_init_uhs_card() the
check is done on the capability of the card.

This difference is causing some issues with some SDIO cards in DDR50
mode where the CDM19 is wrongly issued.

With this patch we modify the check in both
mmc_(sd|sdio)_init_uhs_card() functions to take the proper decision
only according to the actual timing specification.

Cc: stable@vger.kernel.org
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-01-14 10:59:09 +01:00
Russell King
d9812780a0 mmc: sd: limit SD card power limit according to cards capabilities
The SD card specification allows cards to error out a SWITCH command
where the requested function in a group is not supported.  The spec
provides for a set of capabilities which indicate which functions are
supported.

In the case of the power limit, requesting an unsupported power level
via the SWITCH command fails, resulting in the power level remaining at
the power-on default of 0.72W, even though the host and card may support
higher powers levels.

This has been seen with SanDisk 8GB cards, which support the default
0.72W and 1.44W (200mA and 400mA) in combination with an iMX6 host,
supporting up to 2.88W (800mA).  This currently causes us to try to set
a power limit function value of '3' (2.88W) which the card errors out
on, and thereby causes the power level to remain at 0.72W rather than
the desired 1.44W.

Arrange to limit the selected current limit by the capabilities reported
by the card to avoid the SWITCH command failing.  Select the highest
current limit that the host and card combination support.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes: a39ca6ae0a ("mmc: core: Simplify and fix for SD switch processing")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-01-13 10:56:27 +01:00
Adrian Hunter
520322d92e mmc: It is not an error for the card to be removed while suspended
A card can be removed while it is runtime suspended.
Do not print an error message.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-12-28 12:51:38 +01:00
Ulf Hansson
c29536e85b mmc: core: Make runtime resume default behavior for MMC/SD
MMC_CAP_RUNTIME_RESUME was invented to decrease system PM resume time for
systems that particularly needs this. As the feature has matured let's
make it the default behavior for MMC/SD.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-12-22 11:32:03 +01:00
Sergei Shtylyov
2860d060ac mmc: skip reclaiming host on mmc_add_card() error
There's little sense in releasing the host on mmc_add_card() error
immediately after reclaiming  it, so reclaim the host  only in case
of success.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-10-26 16:00:14 +01:00
Ulf Hansson
9eadcc0581 mmc: core: Remove MMC_CLKGATE
MMC_CLKGATE was once invented to save power by gating the bus clock at
request inactivity. At that time it served its purpose. The modern way to
deal with power saving for these scenarios, is by using runtime PM.

Nowadays, several host drivers have deployed runtime PM, but for those
that haven't and which still cares power saving at request inactivity,
it's certainly time to deploy runtime PM as it has been around for several
years now.

To simplify code to mmc core and thus decrease maintenance efforts, this
patch removes all code related to MMC_CLKGATE.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-26 16:00:09 +01:00
Weijun Yang
4324f6de6d mmc: core: enable CMD19 tuning for DDR50 mode
As SD Specifications Part1 Physical Layer Specification Version
3.01 says, CMD19 tuning is available for unlocked cards in transfer
state of 1.8V signaling mode. The small difference between v3.00
and 3.01 spec means that CMD19 tuning is also available for DDR50
mode.

Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-10-26 16:00:03 +01:00
Yousong Zhou
bf8b8511af mmc: sd: Remove superfluous error code assignment
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-10-26 15:59:53 +01:00
Ulf Hansson
3056c49c35 mmc: core: Remove redundant ->power_restore() callback for SD
Since the ->reset() callback is implemented for SD, the ->power_restore()
callback has become redundant, let's remove it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-04 10:03:51 +02:00
Adrian Hunter
3853a04232 mmc: core: Record card drive strength
In preparation for adding drive strength support
for eMMC, add drive_strength to struct mmc_card
to record the card drive strength for UHS-I modes
and HS200 / HS400. For eMMC this will be needed
when switching between HS200 and HS400.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01 09:07:13 +02:00
Adrian Hunter
e23350b35d mmc: core: Factor out common code in drive strength selection
Make a new function out of common code used for drive
strength selection.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01 09:07:12 +02:00
Adrian Hunter
f168359efb mmc: core: Add 'card' to drive strength selection callback
In preparation for supporting also eMMC drive strength,
add the 'card' as a parameter so that the callback can
distinguish different types of cards if necessary.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01 09:07:12 +02:00
Adrian Hunter
fa021cef1a mmc: core: Simplify card drive strength mask
Card drive strength selection uses a callback to
which a mask of supported drive strengths is passed.
Currently, the bits are checked against the values
in the SD specifications. That is not necessary
because the callback will anyway match the mask
against a valid value. Simplify by taking the mask
as is but still ensuring that the default mandatory
value (type B) is always supported.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01 09:07:11 +02:00
Adrian Hunter
b4f30a174e mmc: core: Allow card drive strength to be different to host
Initialization of UHS-I modes for SD and SDIO cards
employs a callback to allow the host driver to
choose a drive strength value. Currently that
assumes the card drive strength and host driver
type must be the same value. Change to let the
callback make that decision and return both the
card drive strength and host driver type.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01 09:07:11 +02:00
Lars-Peter Clausen
9f6e0bff2a mmc: Add support for disabling write-protect detection
It is not uncommon to see systems where there is no physical write-protect
signal (e.g. when using eMMC or microSD card slots). For some controllers,
which have a dedicated write-protection detection logic (like SDHCI
controllers), the get_ro() callback can return bogus data in such a case.

Instead of handling this on a per controller basis this patch adds a new
capability flag to the MMC core that can be set to specify that the result
of get_ro() is invalid. When the flag is set the core will not call
get_ro() and assume that the card is always read-write.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01 09:06:59 +02:00
Linus Torvalds
d0bbe0dd35 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
 "Usual trivial tree updates.  Nothing outstanding -- mostly printk()
  and comment fixes and unused identifier removals"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
  goldfish: goldfish_tty_probe() is not using 'i' any more
  powerpc: Fix comment in smu.h
  qla2xxx: Fix printks in ql_log message
  lib: correct link to the original source for div64_u64
  si2168, tda10071, m88ds3103: Fix firmware wording
  usb: storage: Fix printk in isd200_log_config()
  qla2xxx: Fix printk in qla25xx_setup_mode
  init/main: fix reset_device comment
  ipwireless: missing assignment
  goldfish: remove unreachable line of code
  coredump: Fix do_coredump() comment
  stacktrace.h: remove duplicate declaration task_struct
  smpboot.h: Remove unused function prototype
  treewide: Fix typo in printk messages
  treewide: Fix typo in printk messages
  mod_devicetable: fix comment for match_flags
2015-04-14 09:50:27 -07:00
Masanari Iida
f42cf8d6a3 treewide: Fix typo in printk messages
This patch fix spelling typo in printk messages.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-06 23:04:40 +01:00
Adrian Hunter
63e415c640 mmc: core: Simplify by adding mmc_execute_tuning()
For each MMC, SD and SDIO there is code that
holds the clock, calls ops->execute_tuning, and
releases the clock. Simplify the code a bit by
providing a separate function to do that.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-19 09:56:30 +01:00
Johan Rudholm
dc0ecfef29 mmc: sd: add reset bus_ops callback
Enable power cycle and re-initialization of SD cards via the reset
bus_ops. Power cycling a buggy SD card sometimes helps it get back on
track.

Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-19 09:56:28 +01:00
Doug Anderson
eac86321b5 mmc: core: Support the optional init_card() callback for MMC and SD
In (3fcb027 ARM: MXC: mxcmmc: work around a bug in the SDHC busy line
handling) the optional init_card() callback was added.  According to
the original change it was "for now only called from
mmc_sdio_init_card()".

This callback really ought to be called from the SD and MMC init
functions as well.  One current user of this callback
(mxcmci_init_card) will not work as expected if you insert an SDIO
card, then eject it and put a normal SD card in.  Specifically the
normal SD card will not get to run with 4-bit data.

I'd like to use the init_card() callback to handle a similar quirk on
dw_mmc when using SDIO Interrupts (the "low power" feature of the card
needs to be disabled), so that will add a second user of the function.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-19 09:56:04 +01:00
Joe Perches
6606110d89 mmc: Convert pr_warning to pr_warn
Use the much more common pr_warn instead of pr_warning.

Other miscellanea:

o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-24 10:13:09 +02:00
Sascha Hauer
3d705d14fe mmc: implement Driver Stage Register handling
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.

Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.

This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:07 +02:00
Seungwon Jeon
cdc991790c mmc: drop the speed mode of card's state
Timing mode identifier has same role and can take the place
of speed mode. This change removes all related speed mode.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12 18:05:53 -04:00
Axel Lin
d1e58212ca mmc: Convert to use ATTRIBUTE_GROUPS
Use new ATTRIBUTE_GROUPS macro to declare attribute groups.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
2014-04-22 07:06:38 -04:00