When freeing a gpio that has not been exported, gpio_unexport() prints a
debug message when it should just fall through silently.
Example spurious message:
gpio_unexport: gpio0 status -22
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
Cc: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found in the Versatile build:
WARNING: drivers/built-in.o(.data+0x14c): Section mismatch in reference from the variable pl061_gpio_driver to the (unknown reference) .init.data:(unknown)
The variable pl061_gpio_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x40f8): Section mismatch in reference from the variable pl011_driver to the (unknown reference) .init.data:(unknown)
The variable pl011_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x5ab4): Section mismatch in reference from the variable pl031_driver to the (unknown reference) .init.data:(unknown)
The variable pl031_driver references
the (unknown reference) __initdata (unknown)
Basically, amba_id structures must not be __initdata. Also fix:
WARNING: drivers/built-in.o(.data+0x138): Section mismatch in reference from the variable pl061_gpio_driver to the function .init.text:pl061_probe()
The variable pl061_gpio_driver references
the function __init pl061_probe()
which is an incorrectly annotated probe function. Fix it to reflect
the other AMBA bus probe functions by removing the __init attributation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
My Collabora address is no longer enabled - update the MODULE_AUTHOR
fields of drivers to my current email address.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update Kconfig and Makefile in drivers/gpio to discourage inappropriate
addition of platform-specific code.
[akpm@linux-foundation.org: fix tpyo]
Signed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rdc_gpio_set_value_impl has the gpio data registers 1 and 2 inverted, fix this.
Signed-off-by: Bernhard Loos <bernhardloos@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The rdc321x southbridge PCI device has no MEM PCI resources that we could
pass to mfd_add_devices. Since 33254dd5, mfd_add_device checks for the
mem_base argument that we set to NULL. Changing the resources passed to
our MFD cells from IORESOURCE_MEM to IORESOURCE_IO fixes that. Since we use
those resources as offsets to the PCI configuration space base address of
the southbridge device this is also more adequate.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix rdc321x-southbridge build: GPIO_RDC321X needs to select
MFD_CORE so that the core is built at the same (or higher)
tristate level.
rdc321x-southbridge.c:(.devinit.text+0x6103): undefined reference to `mfd_add_devices'
rdc321x-southbridge.c:(.devexit.text+0xe5f): undefined reference to `mfd_remove_devices'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a GPIO driver to support the GPIOs on the TC35892 I/O Expander.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Janz VMOD-TTL is a MODULbus daughterboard which fits onto any MODULbus
carrier board. It essentially consists of some various logic and a Zilog
Z8536 CIO Counter/Timer and Parallel IO Unit.
The board must be physically configured with jumpers to enable a user to
drive output signals. I am only interested in outputs, so I have made this
driver as simple as possible. It only supports a very minimal subset of the
features provided by the Z8536 chip.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a new GPIO driver for the RDC321x SoC GPIO controller.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This eliminates the following build warning:
drivers/gpio/it8761e_gpio.c: In function `it8761e_gpio_exit':
drivers/gpio/it8761e_gpio.c:220: warning: ignoring return value of `gpiochip_remove', declared with attribute warn_unused_result
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel Penwell chip has two 96 pins GPIO blocks, which are very similiar as
Intel Langwell chip GPIO block, except for pin number difference. This
patch expends the original Langwell GPIO driver to support Penwell's.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few architectures, like OMAP, allow you to set a debouncing time for the
gpio before generating the IRQ. Teach gpiolib about that.
Mark said:
: This would be generally useful for embedded systems, especially where
: the interrupt concerned is a wake source. It allows drivers to avoid
: spurious interrupts from noisy sources so if the hardware supports it
: the driver can avoid having to explicitly wait for the signal to become
: stable and software has to cope with fewer events. We've lived without
: it for quite some time, though.
David said:
: I looked at adding debounce support to the generic GPIO calls (and thus
: gpiolib) some time back, but decided against it. I forget why at this
: time (check list archives) but it wasn't because of lack of utility in
: certain contexts.
:
: One thing to watch out for is just how variable the hardware capabilities
: are. Atmel GPIOs have something like a fixed number of 32K clock cycles
: for debounce, twl4030 had something odd, OMAPs were more like the Atmel
: chips but with a different clock. In some cases debouncing had to be
: ganged, not per-GPIO. And so forth.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current message, 'not registered' is confusing as it implies it was
not registered with something, whereas printing 'failed to register'
implies it was the gpiochip_add() call that did not work correctly.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug I noticed while hacking on the max732x driver for interrupt
support. According to the datasheets, open-drain pins have to be
configured as output-high (which in that case is actually high impedance)
to be used as input.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setup both client_group_a and client_group_b if nr_port > 8 (not including
nr_port==8).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The valid offset value is 0..PL061_GPIO_NR-1, this patch corrects the
offset value range checking.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gpiolib doesn't need to modify the names and I assume most initializers
use string constants that shouldn't be modified anyhow.
[akpm@linux-foundation.org: fix drivers/gpio/cs5535-gpio.c]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kevin Wells <kevin.wells@nxp.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the GPIO expanders supported by the max732x driver have interrupt
generation capability by reporting changes on input pins through an INT#
pin. This patch implements the irq_chip functionnality (edge detection
only).
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jebediah Huang <jebediah.huang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The problem. When implementing a network namespace I need to be able
to have multiple network devices with the same name. Currently this
is a problem for /sys/class/net/*, /sys/devices/virtual/net/*, and
potentially a few other directories of the form /sys/ ... /net/*.
What this patch does is to add an additional tag field to the
sysfs dirent structure. For directories that should show different
contents depending on the context such as /sys/class/net/, and
/sys/devices/virtual/net/ this tag field is used to specify the
context in which those directories should be visible. Effectively
this is the same as creating multiple distinct directories with
the same name but internally to sysfs the result is nicer.
I am calling the concept of a single directory that looks like multiple
directories all at the same path in the filesystem tagged directories.
For the networking namespace the set of directories whose contents I need
to filter with tags can depend on the presence or absence of hotplug
hardware or which modules are currently loaded. Which means I need
a simple race free way to setup those directories as tagged.
To achieve a reace free design all tagged directories are created
and managed by sysfs itself.
Users of this interface:
- define a type in the sysfs_tag_type enumeration.
- call sysfs_register_ns_types with the type and it's operations
- sysfs_exit_ns when an individual tag is no longer valid
- Implement mount_ns() which returns the ns of the calling process
so we can attach it to a sysfs superblock.
- Implement ktype.namespace() which returns the ns of a syfs kobject.
Everything else is left up to sysfs and the driver layer.
For the network namespace mount_ns and namespace() are essentially
one line functions, and look to remain that.
Tags are currently represented a const void * pointers as that is
both generic, prevides enough information for equality comparisons,
and is trivial to create for current users, as it is just the
existing namespace pointer.
The work needed in sysfs is more extensive. At each directory
or symlink creating I need to check if the directory it is being
created in is a tagged directory and if so generate the appropriate
tag to place on the sysfs_dirent. Likewise at each symlink or
directory removal I need to check if the sysfs directory it is
being removed from is a tagged directory and if so figure out
which tag goes along with the name I am deleting.
Currently only directories which hold kobjects, and
symlinks are supported. There is not enough information
in the current file attribute interfaces to give us anything
to discriminate on which makes it useless, and there are
no potential users which makes it an uninteresting problem
to solve.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SIO chip contains 16 possible gpio lines, not 14. The schematic was
not read carefully.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
spi: spidev_test gives error upon 1-byte transfer
omap2_mcspi: small fixes of output data format
omap2_mcspi: Flush posted writes
spi: spi_device memory should be released instead of device.
spi: release device claimed by bus_find_device_by_name
of: check for IS_ERR()
serial/mpc52xx_uart: Drop outdated comments
gpio: potential null dereference
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6061/1: PL061 GPIO: Bug fix - setting gpio for HIGH_LEVEL interrupt is not working.
ARM: 5957/1: ARM: RealView SD/MMC Card detection and write-protect using GPIOLIB
ARM: 6030/1: KS8695: enable console
ARM: 6060/1: PL061 GPIO: Setting gpio val after changing direction to OUT.
ARM: 6059/1: PL061 GPIO: Changing *_irq_chip_data with *_irq_data for real irqs.
ARM: 6023/1: update bcmring_defconfig to latest version and fix build error
ARM: fix build error in arch/arm/kernel/process.c
In current implementation of PL061, setting type of irq to HIGH_LEVEL is not
working. This patch fixes this bug.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Smatch found a potential null dereference in gpio_setup_irq(). The
"pdesc" variable is allocated with idr_find() that can return NULL. If
gpio_setup_irq() is called with 0 as gpio_flags and "pdesc" is null, it
would OOPs here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Bill Gatliff reported the following bug when using the irq_chip facility
of the pca953x driver on a PPC platform:
BUG: scheduling while atomic: insmod/1530/0x00000002
He traced it back to an i2c transaction in pca953x_irq_set_type(), which
can be called with interrupt disabled (from __setup_irq()). As the i2c
controller can sleep while sending a message, this qualifies as a bad
idea.
This patch moves the i2c transaction to pca953x_irq_bus_sync_unlock(),
where it is actually safe to send an i2c message.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Reported-by: Bill Gatliff <bgat@billgatliff.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pl061_direction_output doesn't set value of gpio to value passed to it.
This patch sets value of GPIO pin to requested value after changing direction
to OUT.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL061 driver is using set_irq_chip_data and get_irq_chip_data for real
irq lines. It must be using *_irq_data functions instead. As chip_data
is used by interrupt controllers also, which makes vic write at incorrect
addresses.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In an error handling case the lock is not unlocked. The return is
converted to a goto, to share the unlock at the end of the function.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E1;
identifier f;
@@
f (...) { <+...
* spin_lock_irqsave (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
According to the header in max730x it is licensed GPLv2.
Add a MODULE_LICENSE to avoid getting the kernel tainted.
[w.sang@pengutronix.de: add MODULE_AUTHOR and MODULE_DESCRIPTION also]
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.
Also drivers can extend the attributes with own data fields
and use that in the low level function.
This makes the class attributes the same as sysdev_class attributes
and plain attributes.
This will allow further cleanups in drivers.
Full tree sweep converting all users.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
LPC_SCH is selected by GPI_SCH and I2C_ISCH, even when PCI is not
enabled, but LPC_SCH depends on PCI, so make GPI_SCH and I2C_ISCH
also depend on PCI.
Those 2 selects also need to select what LPC_SCH selects,
since kconfig does not follow selects.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is the chip default but it's possible the bootloader or OTP
will have been configured to a different mode (eg, to provide
feedback during startup).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Revision B of the WM831x devices changes the sense of the tristate
bit for GPIO configuration, inverting it to become an enable instead.
Take account of this in the gpiolib driver.
A current sink regulation status bit has also been added in revision B,
add a flag indicating if it's present but don't use it yet.
This revision also adds an interrupt on key up for the ON pin event
which the existing code is able to take advantage of.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
wm831x_gpio_direction_output() ignored the state passed into it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cs5535-gpio driver's get() function was returning the output value.
This means that the GPIO pins would never work as an input, even if
configured as an input.
The driver should return the READ_BACK value, which is the sensed line
value. To make that work when the direction is 'output', INPUT_ENABLE
needs to be set.
In addition, the driver was not disabling OUTPUT_ENABLE when the direction
is set to 'input'. That would cause the GPIO to continue to drive the pin
if the direction was ever set to output.
This issue was noticed when attempting to use the gpiolib driver to read
an external input. I had previously been using the char/cs5535-gpio
driver.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@kernel.org> [2.6.33.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
