In kernel Bugzilla #15825, a case where routine ssb_bus_pcibus_register()
fails silently is reported. The cause for the failure is still being
investigated; however, the diagnosis would be easier if the failure
had been reported.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our offset handling becomes even a little more hackish now. For some reason I
do not understand all offsets as inrelative. It assumes base offset is 0x1000
but it will work for now as we make offsets relative anyway by removing base
0x1000. Should be cleaner however.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Attempting to read registers that don't exist on the SSB bus can cause
hangs on some boxes. At least some b43 devices are 'in the wild' that
don't have SPROMs at all. When the SSB bus support loads, it attempts
to read these (non-existant) SPROMs and causes hard hangs on the box --
no console output, etc.
This patch adds some intelligence to determine whether or not the SPROM
is present before attempting to read it. This avoids those hard hangs
on those devices with no SPROM attached to their SSB bus. The
SSB-attached devices (e.g. b43, et al.) won't work, but at least the box
will survive to test further patches. :-)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Michael Buesch <mb@bu3sch.de>
The latest changes in the N PHY core require the symbol
ssb_chipco_gpio_control to be exported.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the N PHYs need a revision in the handling of the PMU.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Explicitely enable shared interrupt 2 for any core that didn't get a dedicated IRQ
anymore (fallthrough case) and for EXTIF cores to make gpio interrupts work.
Also remove a bogus comment.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a CONFIG_SSB_SDIOHOST typo.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Reported-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Tested-By: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The range check in the sprom image parser hex2sprom() is broken.
One sprom word is 4 hex characters.
This fixes the check and also adds much better sanity checks to the code.
We better make sure the image is OK by doing some sanity checks to avoid
bricking the device by accident.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SPROM writing routines were broken since we rewrote the suspend
handling on wireless devices, because SPROM writing depended on suspend.
This patch changes it and freezes devices with the driver remove(), probe()
callbacks instead. This also simplifies the whole logics a lot.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At present, the results of an SSB core scan are only logged when
CONFIG_SSB_DEBUG is "y". As this may not be set in a distro kernel,
it is difficult interpret many problems posted in bug reports or in
help forums.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan function was using 32 bit access which does not
work on 16bit CF cards.
This patch corrects this by doing two 16 bit reads like
ssb_pcmcia_read32 already does.
mb -- Removed locking. That early in init there's no need for locking.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SSB is a prime example of how to make use of the new CIS helpers.
CC: Michael Buesch <mb@bu3sch.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fix printk format warnings:
drivers/ssb/sdio.c:336: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
drivers/ssb/sdio.c:443: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an SPROM revision is not recognized, the code falls back to a V1
SPROM; however, that revision is not forced in the appropriate structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for communicating with a Sonics Silicon Backplane through a
SDIO interface, as found in the Nintendo Wii WLAN daughter card.
The Nintendo Wii WLAN card includes a custom Broadcom 4318 chip with
a SDIO host interface.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SSB modinit should not succeed, if busattach failed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the "PMU LDO set voltage" and "PMU LDO PA ref enable"
functions, and use them during LP-PHY baseband init in b43.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a "SPEX32" macro for extracting 32-bit SPROM variables.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
cxgb3: Fix crash caused by stashing wrong netdev_queue
ixgbe: Fix coexistence of FCoE and Flow Director in 82599
memory barrier: adding smp_mb__after_lock
net: adding memory barrier to the poll and receive callbacks
netpoll: Fix carrier detection for drivers that are using phylib
includecheck fix: include/linux, rfkill.h
p54: tx refused but queue active
Atheros Kconfig needs to be dependent on WLAN_80211
mac80211: fix docbook
mac80211_hwsim: avoid NULL access
ssb: Add support for 4318E
b43: Add support for 4318E
zd1211rw: adding SONY IFU-WLM2 (054c:0257) as a zd1211b device
zd1211rw: 07b8:6001 is a ZD1211B
r6040: bump driver version to 0.24 and date to 08 July 2009
r6040: restore MIER register correctly when IRQ line is shared
ipv4: Fix fib_trie rebalancing, part 4 (root thresholds)
davinci_emac: fix kernel oops when changing MAC address while interface is down
igb: set lan id prior to configuring phy
mac80211: minstrel: avoid accessing negative indices in rix_to_ndx()
...
Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: Clyde McPherson <ccmcphe@verizon.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current ssb irq setup in ssb_mipscore_init has the problem that it
configures some device on some irq without checking that the irq is not
taken by an other device.
For example in my case PCI host is on irq 0 and IPSEC on irq 3.
The current code:
- store in dev->irq that IPSEC irq is 3 + 2
- do a set_irq 0->3 on PCI host
But now IPSEC irq is not routed anymore to the mips code and dev->irq is
wrong. This causes a problem described in [1].
This patch tries to solve the problem by making set_irq configure the
device we want to take the irq on the shared irq0. The previous example
becomes:
- store in dev->irq that IPSEC irq is 3 + 2
- do a set_irq 0->3 on PCI host:
- irq 3 is already taken by IPSEC. do a set_irq 3->0 on IPSEC
I also added some code to print the irq configuration after irq setup to
allow easier debugging. And I add extra checking in ssb_mips_irq to report
device without irq or device with not routed irq.
[1] http://www.danm.de/files/src/bcm5365p/REPORTED_DEVICES
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by : Michael Buesch <mb@bu3sch.de>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
this patch export ssb_watchdog_timer_set to allow to use it in a Linux
watchdog driver.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by : Michael Buesch <mb@bu3sch.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds SSB functionality to register a fallback SPROM image from the
architecture setup code.
Weird architectures exist that have half-assed SSB devices without SPROM attached to
their PCI busses. The architecture can register a fallback SPROM image that is
used if no SPROM is found on the SSB device.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for the SSB PMU.
A PMU is found on Low-Power devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds detection code for the LP-PHY and SPROM
extraction code for version 8, which is needed by the LP-PHY and
newer N-PHY.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used on my macbook. N PHY, obviously nothing works
yet, but we can detect the chip with this patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
CC: Michael Buesch <mb@bu3sch.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the target system cannot support SSB, then don't show the menu option as
it'll simply be an empty submenu.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SSB_BUSTYPE_SSB type devices, we need to initialize dma_mask using
coherent_dma_mask so that calls to dma_set_mask() succeed.
It fixes the regression on the b44 driver introduced by commit
f225763a7d
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Only rev 1 and 2 ssb SPROMs have fields named et0mac and et1mac;
however, all of the extraction routines extract pseudo data for these
fields from regions that are all 1's resulting in a hardware address
of FF:FF:FF:FF:FF:FF. This patch forces such a fill at the beginning of
the data extraction process, and only does the formal extraction if the
SPROM rev is 1 or 2.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although a revision 5 SPROM has not been seen in the wild, the
open-source portion of the MIPS driver 4.150.10.5 describes its
layout, which is mostly inherited from revision 4. This patch
implements the differences.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CS_NO_MORE_ITEMS is returned by the CIS tuple reading and parsing code if
the end of a tuple chain is reached. As at least one PCMCIA driver relies
on matching this return value, replace it with -ENOSPC which is now
uniquely used for this purpose within the in-kernel pcmcia subsystem.
CC: Russell King <rmk+kernel@arm.linux.org.uk>
CC: linux-serial@vger.kernel.org
CC: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of using own error or success codes, the PCMCIA code should rely on
the generic return values. Therefore, replace all occurrences of CS_SUCCESS
with 0.
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Makes ssb work on system without a PCI bus.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On embedded devices we must not route the interrupts through
the PCI core, if our host-bus is not PCI.
Reported-by: Steve Brown <sbrown@cortland.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a rewrite of the DMA API for SSB devices.
This is needed, because the old (non-existing) "API" made too many bad
assumptions on the API of the host-bus (PCI).
This introduces an almost complete SSB-DMA-API that maps to the lowlevel
bus-API based on the bustype.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
