Pull x86 asm updates from Ingo Molnar:
"The main changes in this cycle were:
- MSR access API fixes and enhancements (Andy Lutomirski)
- early exception handling improvements (Andy Lutomirski)
- user-space FS/GS prctl usage fixes and improvements (Andy
Lutomirski)
- Remove the cpu_has_*() APIs and replace them with equivalents
(Borislav Petkov)
- task switch micro-optimization (Brian Gerst)
- 32-bit entry code simplification (Denys Vlasenko)
- enhance PAT handling in enumated CPUs (Toshi Kani)
... and lots of other cleanups/fixlets"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
x86/arch_prctl/64: Restore accidentally removed put_cpu() in ARCH_SET_GS
x86/entry/32: Remove asmlinkage_protect()
x86/entry/32: Remove GET_THREAD_INFO() from entry code
x86/entry, sched/x86: Don't save/restore EFLAGS on task switch
x86/asm/entry/32: Simplify pushes of zeroed pt_regs->REGs
selftests/x86/ldt_gdt: Test set_thread_area() deletion of an active segment
x86/tls: Synchronize segment registers in set_thread_area()
x86/asm/64: Rename thread_struct's fs and gs to fsbase and gsbase
x86/arch_prctl/64: Remove FSBASE/GSBASE < 4G optimization
x86/segments/64: When load_gs_index fails, clear the base
x86/segments/64: When loadsegment(fs, ...) fails, clear the base
x86/asm: Make asm/alternative.h safe from assembly
x86/asm: Stop depending on ptrace.h in alternative.h
x86/entry: Rename is_{ia32,x32}_task() to in_{ia32,x32}_syscall()
x86/asm: Make sure verify_cpu() has a good stack
x86/extable: Add a comment about early exception handlers
x86/msr: Set the return value to zero when native_rdmsr_safe() fails
x86/paravirt: Make "unsafe" MSR accesses unsafe even if PARAVIRT=y
x86/paravirt: Add paravirt_{read,write}_msr()
x86/msr: Carry on after a non-"safe" MSR access fails
...
When I added support for the Memory Protection Keys processor
feature, I had to reindent the REQUIRED/DISABLED_MASK macros, and
also consult the later cpufeature words.
I'm not quite sure how I bungled it, but I consulted the wrong
word at the end. This only affected required or disabled cpu
features in cpufeature words 14, 15 and 16. So, only Protection
Keys itself was screwed over here.
The result was that if you disabled pkeys in your .config, you
might still see some code show up that should have been compiled
out. There should be no functional problems, though.
In verifying this patch I also realized that the DISABLE_PKU/OSPKE
macros were defined backwards and that the cpu_has() check in
setup_pku() was not doing the compile-time disabled checks.
So also fix the macro for DISABLE_PKU/OSPKE and add a compile-time
check for pkeys being enabled in setup_pku().
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: dfb4a70f20 ("x86/cpufeature, x86/mm/pkeys: Add protection keys related CPUID definitions")
Link: http://lkml.kernel.org/r/20160513221328.C200930B@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a new CPUID leaf to hold the contents of CPUID 0x80000007_EBX (RasCap).
Define bits that are currently in use:
Bit 0: McaOverflowRecov
Bit 1: SUCCOR
Bit 3: ScalableMca
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
[ Shorten comment. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1462971509-3856-5-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use static_cpu_has() in the timing-sensitive paths in fpstate_init() and
fpu__copy().
While at it, simplify the use in init_cyrix() and get rid of the ternary
operator.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1459801503-15600-6-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use static_cpu_has() in __flush_tlb_all() due to the time-sensitivity of
this one.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1459266123-21878-10-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kirill Shutemov pointed this out to me.
The tip tree currently has commit:
dfb4a70f2 [x86/cpufeature, x86/mm/pkeys: Add protection keys related CPUID definitions]
whioch added support for two new CPUID bits: X86_FEATURE_PKU and
X86_FEATURE_OSPKE. But, those bits were mis-merged and put in
cpufeature.h instead of cpufeatures.h.
This didn't cause any breakage *except* it keeps the "ospke" and
"pku" bits from showing up in cpuinfo.
Now cpuinfo has the two new flags:
flags : ... pku ospke
BTW, is it really wise to have cpufeature.h and cpufeatures.h?
It seems like they can only cause confusion and mahem with tab
completion.
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160310221213.06F9DB53@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are two CPUID bits for protection keys. One is for whether
the CPU contains the feature, and the other will appear set once
the OS enables protection keys. Specifically:
Bit 04: OSPKE. If 1, OS has set CR4.PKE to enable
Protection keys (and the RDPKRU/WRPKRU instructions)
This is because userspace can not see CR4 contents, but it can
see CPUID contents.
X86_FEATURE_PKU is referred to as "PKU" in the hardware documentation:
CPUID.(EAX=07H,ECX=0H):ECX.PKU [bit 3]
X86_FEATURE_OSPKE is "OSPKU":
CPUID.(EAX=07H,ECX=0H):ECX.OSPKE [bit 4]
These are the first CPU features which need to look at the
ECX word in CPUID leaf 0x7, so this patch also includes
fetching that word in to the cpuinfo->x86_capability[] array.
Add it to the disabled-features mask when its config option is
off. Even though we are not using it here, we also extend the
REQUIRED_MASK_BIT_SET() macro to keep it mirroring the
DISABLED_MASK_BIT_SET() version.
This means that in almost all code, you should use:
cpu_has(c, X86_FEATURE_PKU)
and *not* the CONFIG option.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20160212210201.7714C250@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When GCC cannot do constant folding for this macro, it falls back to
cpu_has(). But static_cpu_has() is optimal and it works at all times
now. So use it and speedup the fallback case.
Before we had this:
mov 0x99d674(%rip),%rdx # ffffffff81b0d9f4 <boot_cpu_data+0x34>
shr $0x2e,%rdx
and $0x1,%edx
jne ffffffff811704e9 <do_munmap+0x3f9>
After alternatives patching, it turns into:
jmp 0xffffffff81170390
nopl (%rax)
...
callq ffffffff81056e00 <mpx_notify_unmap>
ffffffff81170390: mov 0x170(%r12),%rdi
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1455578358-28347-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move the code to do the dynamic check to the altinstr_aux
section so that it is discarded after alternatives have run and
a static branch has been chosen.
This way we're changing the dynamic branch from C code to
assembly, which makes it *substantially* smaller while avoiding
a completely unnecessary call to an out of line function.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
[ Changed it to do TESTB, as hpa suggested. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Young <dyoung@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: Laura Abbott <labbott@fedoraproject.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1452972124-7380-1-git-send-email-brgerst@gmail.com
Link: http://lkml.kernel.org/r/20160127084525.GC30712@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I can simply quote hpa from the mail:
"Get rid of the non-asm goto variant and just fall back to
dynamic if asm goto is unavailable. It doesn't make any sense,
really, if it is supposed to be safe, and by now the asm
goto-capable gcc is in more wide use. (Originally the gcc 3.x
fallback to pure dynamic didn't exist, either.)"
Booy, am I lazy.
Cleanup the whole CC_HAVE_ASM_GOTO ifdeffery too, while at it.
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160127084325.GB30712@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
So the old one didn't work properly before alternatives had run.
And it was supposed to provide an optimized JMP because the
assumption was that the offset it is jumping to is within a
signed byte and thus a two-byte JMP.
So I did an x86_64 allyesconfig build and dumped all possible
sites where static_cpu_has() was used. The optimization amounted
to all in all 12(!) places where static_cpu_has() had generated
a 2-byte JMP. Which has saved us a whopping 36 bytes!
This clearly is not worth the trouble so we can remove it. The
only place where the optimization might count - in __switch_to()
- we will handle differently. But that's not subject of this
patch.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1453842730-28463-6-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move them to a separate header and have the following
dependency:
x86/cpufeatures.h <- x86/processor.h <- x86/cpufeature.h
This makes it easier to use the header in asm code and not
include the whole cpufeature.h and add guards for asm.
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1453842730-28463-5-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This brings .text savings of about ~1.6K when building a tinyconfig. It
is off by default so nothing changes for the default.
Kconfig help text from Josh.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Link: http://lkml.kernel.org/r/1449481182-27541-5-git-send-email-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Those are stupid and code should use static_cpu_has_safe() or
boot_cpu_has() instead. Kill the least used and unused ones.
The remaining ones need more careful inspection before a conversion can
happen. On the TODO.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1449481182-27541-4-git-send-email-bp@alien8.de
Cc: David Sterba <dsterba@suse.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add an enum for the ->x86_capability array indices and cleanup
get_cpu_cap() by killing some redundant local vars.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1449481182-27541-3-git-send-email-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
After 32-bit syscall rewrite, and specifically after commit:
5f310f739b ("x86/entry/32: Re-implement SYSENTER using the new C path")
... the stack frame that is passed to xen_sysexit is no longer a
"standard" one (i.e. it's not pt_regs).
Since we end up calling xen_iret from xen_sysexit we don't need
to fix up the stack and instead follow entry_SYSENTER_32's IRET
path directly to xen_iret.
We can do the same thing for compat mode even though stack does
not need to be fixed. This will allow us to drop usergs_sysret32
paravirt op (in the subsequent patch)
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: david.vrabel@citrix.com
Cc: konrad.wilk@oracle.com
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1447970147-1733-2-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
AMD Fam17h processors introduce support for the CLZERO
instruction. It zeroes out the 64 byte cache line specified in
RAX.
Add the bit here to allow /proc/cpuinfo to list the feature.
Boris: we're adding this as a separate ->x86_capability leaf
because CPUID_80000008_EBX is going to contain more feature bits
and it will fill out with time.
Signed-off-by: Wan Zongshun <Vincent.Wan@amd.com>
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
[ Wrap code in patch form, fix comments. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1446207099-24948-4-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 cpu updates from Ingo Molnar:
"Two changes: a suspend/resume quirk and a new CPUID bit definition"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpufeature: Add feature bit for Intel's Silicon Debug CPUID bit
x86/cpu: Restore MSR_IA32_ENERGY_PERF_BIAS after resume
AMD Carrizo processors (Family 15h, Models 60h-6fh) added a new
feature called MWAITX (MWAIT with extensions) as an extension to
MONITOR/MWAIT.
This new instruction controls a configurable timer which causes
the core to exit wait state on timer expiration, in addition to
"normal" MWAIT condition of reading from a monitored VA.
Compared to MONITOR/MWAIT, there are minor differences in opcode
and input parameters:
MWAITX ECX[1]: enable timer if set
MWAITX EBX[31:0]: max wait time expressed in SW P0 clocks ==
TSC. The software P0 frequency is the same as the TSC frequency.
MWAIT MWAITX
opcode 0f 01 c9 | 0f 01 fb
ECX[0] value of RFLAGS.IF seen by instruction
ECX[1] unused/#GP if set | enable timer if set
ECX[31:2] unused/#GP if set
EAX unused (reserve for hint)
EBX[31:0] unused | max wait time (SW P0 == TSC)
MONITOR MONITORX
opcode 0f 01 c8 | 0f 01 fa
EAX (logical) address to monitor
ECX #GP if not zero
Max timeout = EBX/(TSC frequency)
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andreas Herrmann <herrmann.der.user@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Li <tony.li@amd.com>
Link: http://lkml.kernel.org/r/1439201994-28067-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add Intel CPUID for Intel Secure Hash Algorithm Extensions. This feature
provides new instructions for accelerated computation of SHA-1 and SHA-256.
This allows the feature to be shown in the /proc/cpuinfo for cpus that
support it.
Refer to SHA extension programming guide in chapter 8.2 of the Intel
Architecture Instruction Set Extensions Programming reference
for definition of this feature's cpuid: CPUID.(EAX=07H, ECX=0):EBX.SHA [bit 29] = 1
https://software.intel.com/sites/default/files/managed/07/b7/319433-023.pdf
Originally-by: Chandramouli Narayanan <mouli_7982@yahoo.com>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Link: http://lkml.kernel.org/r/1440194206.3940.6.camel@schen9-mobl2
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a CPUID feature bit for the SDBG (Silicon Debug) CPU feature
found on recent Intel systems starting with Haswell.
Using the IA32_DEBUG_INTERFACE MSR (index C80H) one can at least
detect if SDBG has been enabled by the firmware and if it has
been used or not.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1437330403-12102-1-git-send-email-minipli@googlemail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
AMD CPUs don't reinitialize the SS descriptor on SYSRET, so SYSRET with
SS == 0 results in an invalid usermode state in which SS is apparently
equal to __USER_DS but causes #SS if used.
Work around the issue by setting SS to __KERNEL_DS __switch_to, thus
ensuring that SYSRET never happens with SS set to NULL.
This was exposed by a recent vDSO cleanup.
Fixes: e7d6eefaaa x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull perf changes from Ingo Molnar:
"Core kernel changes:
- One of the more interesting features in this cycle is the ability
to attach eBPF programs (user-defined, sandboxed bytecode executed
by the kernel) to kprobes.
This allows user-defined instrumentation on a live kernel image
that can never crash, hang or interfere with the kernel negatively.
(Right now it's limited to root-only, but in the future we might
allow unprivileged use as well.)
(Alexei Starovoitov)
- Another non-trivial feature is per event clockid support: this
allows, amongst other things, the selection of different clock
sources for event timestamps traced via perf.
This feature is sought by people who'd like to merge perf generated
events with external events that were measured with different
clocks:
- cluster wide profiling
- for system wide tracing with user-space events,
- JIT profiling events
etc. Matching perf tooling support is added as well, available via
the -k, --clockid <clockid> parameter to perf record et al.
(Peter Zijlstra)
Hardware enablement kernel changes:
- x86 Intel Processor Trace (PT) support: which is a hardware tracer
on steroids, available on Broadwell CPUs.
The hardware trace stream is directly output into the user-space
ring-buffer, using the 'AUX' data format extension that was added
to the perf core to support hardware constraints such as the
necessity to have the tracing buffer physically contiguous.
This patch-set was developed for two years and this is the result.
A simple way to make use of this is to use BTS tracing, the PT
driver emulates BTS output - available via the 'intel_bts' PMU.
More explicit PT specific tooling support is in the works as well -
will probably be ready by 4.2.
(Alexander Shishkin, Peter Zijlstra)
- x86 Intel Cache QoS Monitoring (CQM) support: this is a hardware
feature of Intel Xeon CPUs that allows the measurement and
allocation/partitioning of caches to individual workloads.
These kernel changes expose the measurement side as a new PMU
driver, which exposes various QoS related PMU events. (The
partitioning change is work in progress and is planned to be merged
as a cgroup extension.)
(Matt Fleming, Peter Zijlstra; CPU feature detection by Peter P
Waskiewicz Jr)
- x86 Intel Haswell LBR call stack support: this is a new Haswell
feature that allows the hardware recording of call chains, plus
tooling support. To activate this feature you have to enable it
via the new 'lbr' call-graph recording option:
perf record --call-graph lbr
perf report
or:
perf top --call-graph lbr
This hardware feature is a lot faster than stack walk or dwarf
based unwinding, but has some limitations:
- It reuses the current LBR facility, so LBR call stack and
branch record can not be enabled at the same time.
- It is only available for user-space callchains.
(Yan, Zheng)
- x86 Intel Broadwell CPU support and various event constraints and
event table fixes for earlier models.
(Andi Kleen)
- x86 Intel HT CPUs event scheduling workarounds. This is a complex
CPU bug affecting the SNB,IVB,HSW families that results in counter
value corruption. The mitigation code is automatically enabled and
is transparent.
(Maria Dimakopoulou, Stephane Eranian)
The perf tooling side had a ton of changes in this cycle as well, so
I'm only able to list the user visible changes here, in addition to
the tooling changes outlined above:
User visible changes affecting all tools:
- Improve support of compressed kernel modules (Jiri Olsa)
- Save DSO loading errno to better report errors (Arnaldo Carvalho de Melo)
- Bash completion for subcommands (Yunlong Song)
- Add 'I' event modifier for perf_event_attr.exclude_idle bit (Jiri Olsa)
- Support missing -f to override perf.data file ownership. (Yunlong Song)
- Show the first event with an invalid filter (David Ahern, Arnaldo Carvalho de Melo)
User visible changes in individual tools:
'perf data':
New tool for converting perf.data to other formats, initially
for the CTF (Common Trace Format) from LTTng (Jiri Olsa,
Sebastian Siewior)
'perf diff':
Add --kallsyms option (David Ahern)
'perf list':
Allow listing events with 'tracepoint' prefix (Yunlong Song)
Sort the output of the command (Yunlong Song)
'perf kmem':
Respect -i option (Jiri Olsa)
Print big numbers using thousands' group (Namhyung Kim)
Allow -v option (Namhyung Kim)
Fix alignment of slab result table (Namhyung Kim)
'perf probe':
Support multiple probes on different binaries on the same command line (Masami Hiramatsu)
Support unnamed union/structure members data collection. (Masami Hiramatsu)
Check kprobes blacklist when adding new events. (Masami Hiramatsu)
'perf record':
Teach 'perf record' about perf_event_attr.clockid (Peter Zijlstra)
Support recording running/enabled time (Andi Kleen)
'perf sched':
Improve the performance of 'perf sched replay' on high CPU core count machines (Yunlong Song)
'perf report' and 'perf top':
Allow annotating entries in callchains in the hists browser (Arnaldo Carvalho de Melo)
Indicate which callchain entries are annotated in the
TUI hists browser (Arnaldo Carvalho de Melo)
Add pid/tid filtering to 'report' and 'script' commands (David Ahern)
Consider PERF_RECORD_ events with cpumode == 0 in 'perf top', removing one
cause of long term memory usage buildup, i.e. not processing PERF_RECORD_EXIT
events (Arnaldo Carvalho de Melo)
'perf stat':
Report unsupported events properly (Suzuki K. Poulose)
Output running time and run/enabled ratio in CSV mode (Andi Kleen)
'perf trace':
Handle legacy syscalls tracepoints (David Ahern, Arnaldo Carvalho de Melo)
Only insert blank duration bracket when tracing syscalls (Arnaldo Carvalho de Melo)
Filter out the trace pid when no threads are specified (Arnaldo Carvalho de Melo)
Dump stack on segfaults (Arnaldo Carvalho de Melo)
No need to explicitely enable evsels for workload started from perf, let it
be enabled via perf_event_attr.enable_on_exec, removing some events that take
place in the 'perf trace' before a workload is really started by it.
(Arnaldo Carvalho de Melo)
Allow mixing with tracepoints and suppressing plain syscalls. (Arnaldo Carvalho de Melo)
There's also been a ton of infrastructure work done, such as the
split-out of perf's build system into tools/build/ and other changes -
see the shortlog and changelog for details"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (358 commits)
perf/x86/intel/pt: Clean up the control flow in pt_pmu_hw_init()
perf evlist: Fix type for references to data_head/tail
perf probe: Check the orphaned -x option
perf probe: Support multiple probes on different binaries
perf buildid-list: Fix segfault when show DSOs with hits
perf tools: Fix cross-endian analysis
perf tools: Fix error path to do closedir() when synthesizing threads
perf tools: Fix synthesizing fork_event.ppid for non-main thread
perf tools: Add 'I' event modifier for exclude_idle bit
perf report: Don't call map__kmap if map is NULL.
perf tests: Fix attr tests
perf probe: Fix ARM 32 building error
perf tools: Merge all perf_event_attr print functions
perf record: Add clockid parameter
perf sched replay: Use replay_repeat to calculate the runavg of cpu usage instead of the default value 10
perf sched replay: Support using -f to override perf.data file ownership
perf sched replay: Fix the EMFILE error caused by the limitation of the maximum open files
perf sched replay: Handle the dead halt of sem_wait when create_tasks() fails for any task
perf sched replay: Fix the segmentation fault problem caused by pr_err in threads
perf sched replay: Realloc the memory of pid_to_task stepwise to adapt to the different pid_max configurations
...
Add support for the new CLWB (cache line write back)
instruction. This instruction was announced in the document
"Intel Architecture Instruction Set Extensions Programming
Reference" with reference number 319433-022.
https://software.intel.com/sites/default/files/managed/0d/53/319433-022.pdf
The CLWB instruction is used to write back the contents of
dirtied cache lines to memory without evicting the cache lines
from the processor's cache hierarchy. This should be used in
favor of clflushopt or clflush in cases where you require the
cache line to be written to memory but plan to access the data
again in the near future.
One of the main use cases for this is with persistent memory
where CLWB can be used with PCOMMIT to ensure that data has been
accepted to memory and is durable on the DIMM.
This function shows how to properly use CLWB/CLFLUSHOPT/CLFLUSH
and PCOMMIT with appropriate fencing:
void flush_and_commit_buffer(void *vaddr, unsigned int size)
{
void *vend = vaddr + size - 1;
for (; vaddr < vend; vaddr += boot_cpu_data.x86_clflush_size)
clwb(vaddr);
/* Flush any possible final partial cacheline */
clwb(vend);
/*
* Use SFENCE to order CLWB/CLFLUSHOPT/CLFLUSH cache flushes.
* (MFENCE via mb() also works)
*/
wmb();
/* PCOMMIT and the required SFENCE for ordering */
pcommit_sfence();
}
After this function completes the data pointed to by vaddr is
has been accepted to memory and will be durable if the vaddr
points to persistent memory.
Regarding the details of how the alternatives assembly is set
up, we need one additional byte at the beginning of the CLFLUSH
so that we can flip it into a CLFLUSHOPT by changing that byte
into a 0x66 prefix. Two options are to either insert a 1 byte
ASM_NOP1, or to add a 1 byte NOP_DS_PREFIX. Both have no
functional effect with the plain CLFLUSH, but I've been told
that executing a CLFLUSH + prefix should be faster than
executing a CLFLUSH + NOP.
We had to hard code the assembly for CLWB because, lacking the
ability to assemble the CLWB instruction itself, the next
closest thing is to have an xsaveopt instruction with a 0x66
prefix. Unfortunately XSAVEOPT itself is also relatively new,
and isn't included by all the GCC versions that the kernel needs
to support.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1422377631-8986-3-git-send-email-ross.zwisler@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
