This sysctl setting controls whether packet priority should be updated
after forwarding. Configure RGCR.usp accordingly so that the device is
in sync with the kernel handling.
Note that RGCR doesn't allow changing arbitrary parameters
mid-operation, however "usp" is exempt and can be reconfigured.
Also react to NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE notifications
that signify change in this configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The boilerplate to schedule NETEVENT_IPV4_MPATH_HASH_UPDATE and
NETEVENT_IPV6_MPATH_HASH_UPDATE handling is almost equivalent to that of
NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE that's coming in the next
patch. The only difference is which actual worker function should be
called. Extract this boilerplate into a named function in order to allow
reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may make offloading decision based on whether
ip_forward_update_priority is enabled or not. Therefore distribute
netevent notifications to give them a chance to react to a change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After IPv4 packets are forwarded, the priority of the corresponding SKB
is updated according to the TOS field of IPv4 header. This overrides any
prioritization done earlier by e.g. an skbedit action or ingress-qos-map
defined at a vlan device.
Such overriding may not always be desirable. Even if the packet ends up
being routed, which implies this is an L3 network node, an administrator
may wish to preserve whatever prioritization was done earlier on in the
pipeline.
Therefore introduce a sysctl that controls this behavior. Keep the
default value at 1 to maintain backward-compatible behavior.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'protocol' is a user-controlled value, so sanitize it after the bounds
check to avoid using it for speculative out-of-bounds access to arrays
indexed by it.
This addresses the following accesses detected with the help of smatch:
* net/netlink/af_netlink.c:654 __netlink_create() warn: potential
spectre issue 'nlk_cb_mutex_keys' [w]
* net/netlink/af_netlink.c:654 __netlink_create() warn: potential
spectre issue 'nlk_cb_mutex_key_strings' [w]
* net/netlink/af_netlink.c:685 netlink_create() warn: potential spectre
issue 'nl_table' [w] (local cap)
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The construction "net->ipv4.sysctl_ip_nonlocal_bind || inet->freebind
|| inet->transparent" is present three times and its IPv6 counterpart
is also present three times. We introduce two small helpers to
characterize these tests uniformly.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neterion was standalone for several years, then acquired by Exar and
shutdown in 11 months without ever making any new Exar branded adapters.
Users would probably think of them as Neterion and not Exar (as there
have been no follow-on adapters and the vast majority ever sold were
under the Neterion name).
6c541b4595 ("net: ethernet: Sort Kconfig sourcing alphabetically")
sorted Kconfig sourcing based on directory names, but in a couple cases,
the menu item text is quite different from the directory name and is not
sorted correctly:
drivers/net/ethernet/neterion/Kconfig => "Exar devices"
To address that and clear up any confusion about the name, "Exar" was
changed to "Neterion (Exar)" and the relevant entries in the Makefile
and Kconfig were reordered to match the alphabetical organization.
Inspired-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kmemdup is better than kmalloc+memcpy. So replace them.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables 'tn' and 'oport' are being assigned but are never used hence
they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'oport' set but not used [-Wunused-but-set-variable]
warning: variable 'tn' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add overline heading adornment to document title in order to comply
with kernel doc requirements.
Fixes: 60b9131 staging: fsl-mc: Convert documentation to rst format
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh Reddy says:
====================
be2net: patch-set
v1->v2 : Modified the subject line and commit log.
Please consider applying these two patches to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch handles a TX-timeout as follows:
1) This patch gathers and prints the following info that can
help in diagnosing the cause of a TX-timeout.
a) TX queue and completion queue entries.
b) SKB and TCP/UDP header details.
2) For Lancer NICs (TX-timeout recovery is not supported for
BE3/Skyhawk-R NICs), it recovers from the TX timeout as follows:
a) On a TX-timeout, driver sets the PHYSDEV_CONTROL_FW_RESET_MASK
bit in the PHYSDEV_CONTROL register. Lancer firmware goes into
an error state and indicates this back to the driver via a bit
in a doorbell register.
b) Driver detects this and calls be_err_recover(). DMA is disabled,
all pending TX skbs are unmapped and freed (be_close()). All rings
are destroyed (be_clear()).
c) The driver waits for the FW to re-initialize and re-creates all
rings along with other data structs (be_resume())
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential execution path in which variable *err* is returned
without being properly initialized previously.
Fix this by initializing variable *err* to 0.
Addresses-Coverity-ID: 1472116 ("Uninitialized scalar variable")
Fixes: 0ec13877ce ("net/mlx5e: Gather all XDP pre-requisite checks in a single function")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:1534:6: warning: symbol 'qed_cm_init_pf' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:233:4: warning: symbol 'qed_init_qm_get_num_tcs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:238:5: warning: symbol 'qed_init_qm_get_num_vfs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:246:5: warning: symbol 'qed_init_qm_get_num_pf_rls' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:264:5: warning: symbol 'qed_init_qm_get_num_vports' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:276:5: warning: symbol 'qed_init_qm_get_num_pqs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:573:5: warning: symbol 'qed_mcp_nvm_wr_cmd' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:3012:1: warning: symbol '__qed_mcp_resc_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:870:6: warning: symbol 'qed_dcbx_aen' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7841:5: warning: symbol 'qed_dbg_nvm_image_length' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7857:5: warning: symbol 'qed_dbg_nvm_image' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:675:6: warning: symbol '_qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:690:6: warning: symbol 'qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:3982:6: warning: symbol 'qed_iov_pf_get_pending_events' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_vf.c:172:5: warning: symbol '_qed_vf_pf_release' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:137:5: warning: symbol 'qed_rdma_get_sb_id' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:709:5: warning: symbol 'qed_rdma_stop' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_ll2.c:161:6: warning: symbol 'qed_ll2b_complete_rx_packet' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_roce.c:160:6: warning: symbol 'qed_roce_free_cid_pair' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:380:12: warning: symbol 'iwarp_state_names' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:946:1: warning: symbol 'qed_iwarp_parse_private_data' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:971:1: warning: symbol 'qed_iwarp_mpa_reply_arrived' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2504:1: warning: symbol 'qed_iwarp_ll2_slowpath' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2806:6: warning: symbol 'qed_iwarp_qp_in_error' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2827:6: warning: symbol 'qed_iwarp_exception_received' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2958:1: warning: symbol 'qed_iwarp_connect_complete' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:876:6: warning: symbol 'qed_iscsi_free_connection' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <Denis.Bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL won't work in PCI-based setups because we are not saving the PCI EP
state before entering suspend state and not allowing D3 wake.
Fix this by using a wrapper around stmmac_{suspend/resume} which
correctly sets the PCI EP state.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the IPv6 dependency from RDS.
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, rds_ib_conn_alloc() calls rds_ib_recv_alloc_caches()
without passing along the gfp_t flag. But rds_ib_recv_alloc_caches()
and rds_ib_recv_alloc_cache() should take a gfp_t parameter so that
rds_ib_recv_alloc_cache() can call alloc_percpu_gfp() using the
correct flag instead of calling alloc_percpu().
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace ugly macroses on functions.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the optimizations for TLB invalidation from commit 0cef77c779
("powerpc/64s/radix: flush remote CPUs out of single-threaded
mm_cpumask"), the scope of a TLBI (global vs. local) can now be
influenced by the value of the 'copros' counter of the memory context.
When calling mm_context_remove_copro(), the 'copros' counter is
decremented first before flushing. It may have the unintended side
effect of sending local TLBIs when we explicitly need global
invalidations in this case. Thus breaking any nMMU user in a bad and
unpredictable way.
Fix it by flushing first, before updating the 'copros' counter, so
that invalidations will be global.
Fixes: 0cef77c779 ("powerpc/64s/radix: flush remote CPUs out of single-threaded mm_cpumask")
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Immediately flush any outstanding ACK on entry to rxrpc_recvmsg_data() -
which transfers data to the target buffers - if we previously had an Rx
underrun (ie. we returned -EAGAIN because we ran out of received data).
This lets the server know what we've managed to receive something.
Also flush any outstanding ACK after calling the function if it hit -EAGAIN
to let the server know we processed some data.
It might be better to send more ACKs, possibly on a time-based scheme, but
that needs some more consideration.
With this and some additional AFS patches, it is possible to get large
unencrypted O_DIRECT reads to be almost as fast as NFS over TCP. It looks
like it might be theoretically possible to improve performance yet more for
a server running a single operation as investigation of packet timestamps
indicates that the server keeps stalling.
The issue appears to be that rxrpc runs in to trouble with ACK packets
getting batched together (up to ~32 at a time) somewhere between the IP
transmit queue on the client and the ethernet receive queue on the server.
However, this case isn't too much of a worry as even a lightly loaded
server should be receiving sufficient packet flux to flush the ACK packets
to the UDP socket.
Signed-off-by: David Howells <dhowells@redhat.com>
The final ACK that closes out an rxrpc call needs to be transmitted by the
client unless we're going to follow up with a DATA packet for a new call on
the same channel (which implicitly ACK's the previous call, thereby saving
an ACK).
Currently, we don't do that, so if no follow on call is immediately
forthcoming, the server will resend the last DATA packet - at which point
rxrpc_conn_retransmit_call() will be triggered and will (re)send the final
ACK. But the server has to hold on to the last packet until the ACK is
received, thereby holding up its resources.
Fix the client side to propose a delayed final ACK, to be transmitted after
a short delay, assuming the call isn't superseded by a new one.
Signed-off-by: David Howells <dhowells@redhat.com>
Increase the size of a call's Rx window from 32 to 63 - ie. one less than
the size of the ring buffer. This makes large data transfers perform
better when the Tx window on the other side is around 64 (as is the case
with Auristor's YFS fileserver).
If the server window size is ~32 or smaller, this should make no
difference.
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the ACK proposal tracepoint outcomes list by making the one that's an
empty string not an empty string - which gets rendered as a hex number
string instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Trace successful packet transmission (kernel_sendmsg() succeeded, that is)
in AF_RXRPC. We can share the enum that defines the transmission points
with the trace_rxrpc_tx_fail() tracepoint, so rename its constants to be
applicable to both.
Also, save the internal call->debug_id in the rxrpc_channel struct so that
it can be used in retransmission trace lines.
Signed-off-by: David Howells <dhowells@redhat.com>
Show the four current call IDs in /proc/net/rxrpc/conns.
Show the current packet Rx serial number in /proc/net/rxrpc/calls.
Signed-off-by: David Howells <dhowells@redhat.com>
Display in /proc/net/rxrpc/calls the timeout by which a call next expects
to receive a packet.
This makes it easier to debug timeout issues.
Signed-off-by: David Howells <dhowells@redhat.com>
Variables 'sp' and 'did_discard' are being assigned,
but are never used, hence they are redundant and can be removed.
fix following warning:
net/rxrpc/call_event.c:165:25: warning: variable 'sp' set but not used [-Wunused-but-set-variable]
net/rxrpc/conn_client.c:1054:7: warning: variable 'did_discard' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Merge turbostat utility fixes for final 4.18:
- Fix the -S option on 1-CPU systems.
- Fix computations using incorrect processor core counts.
- Fix the x2apic debug message.
- Fix logical node enumeration to allow for non-sequential physical nodes.
- Fix reported family on modern AMD processors.
- Clarify the RAPL column information in the man page.
* pm-tools:
tools/power turbostat: version 18.07.27
tools/power turbostat: Read extended processor family from CPUID
tools/power turbostat: Fix logical node enumeration to allow for non-sequential physical nodes
tools/power turbostat: fix x2apic debug message output file
tools/power turbostat: fix bogus summary values
tools/power turbostat: fix -S on UP systems
tools/power turbostat: Update turbostat(8) RAPL throttling column description
In commit ab123fe071 ("enic: handle mtu change for vf properly")
ASSERT_RTNL() is added to _enic_change_mtu() to prevent it from being
called without rtnl held. enic_probe() calls enic_change_mtu()
without rtnl held. At this point netdev is not registered yet.
Remove call to enic_change_mtu and assign the mtu to netdev->mtu.
Fixes: ab123fe071 ("enic: handle mtu change for vf properly")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_frag_queue() might call pskb_pull() on one skb that
is already in the fragment queue.
We need to take care of possible truesize change, or we
might have an imbalance of the netns frags memory usage.
IPv6 is immune to this bug, because RFC5722, Section 4,
amended by Errata ID 3089 states :
When reassembling an IPv6 datagram, if
one or more its constituent fragments is determined to be an
overlapping fragment, the entire datagram (and any constituent
fragments) MUST be silently discarded.
Fixes: 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently check current frags memory usage only when
a new frag queue is created. This allows attackers to first
consume the memory budget (default : 4 MB) creating thousands
of frag queues, then sending tiny skbs to exceed high_thresh
limit by 2 to 3 order of magnitude.
Note that before commit 648700f76b ("inet: frags: use rhashtables
for reassembly units"), work queue could be starved under DOS,
getting no cpu cycles.
After commit 648700f76b, only the per frag queue timer can eventually
remove an incomplete frag queue and its skbs.
Fixes: b13d3cbfb8 ("inet: frag: move eviction of queues to work queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Peter Oskolkov <posk@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbYMQXAAoJEEg/ir3gV/o+BNcH/R6X7oxLoskYIO9nWejdMKUj
GzojL3mne33mKGEwGyFfLmRWQMbgPUvYrk5mXu/1uFPAHzRA+BwioZeyeWxfCYFe
blJuv59A1EBudSvQKUDEMeXaQYD7/6T92fbu3ZvGiZEZI+OTj3z6PtBU0Tr6NEMZ
zxRKWkpLPdjUwJh51tXEgfmEqy+gnn9tNIZt8ClRJ0w5wbgnignhzx1lCry1SE95
6zNS8aZKRxSIaVY41MxLSTRb9jLBmeZtiD67ntJAZIaLaMIMUqZbhW5Rtt7rz8HZ
chAiY8KdmEM35Ix6+ovzT9FKz/Jhp6/0nDioNYPRT5D3rHcqe+wUb8/8zROnhgs=
=b9YA
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-07-31
The following series includes four mlx5 fixes.
Please pull and let me know if there's any problem.
For -stable v4.14
net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager
For -stable v4.16
net/mlx5e: Set port trust mode to PCP as default
For -stable v4.17
net/mlx5e: IPoIB, Set the netdevice sw mtu in ipoib enhanced flow
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=MN3z
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20180731' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fix from Paul Moore:
"A single small audit fix to guard against memory allocation failures
when logging information about a kernel module load.
It's small, easy to understand, and self-contained; while nothing is
zero risk, this should be pretty low"
* tag 'audit-pr-20180731' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: fix potential null dereference 'context->module.name'
local_timer_softirq_pending() checks whether the timer softirq is
pending with: local_softirq_pending() & TIMER_SOFTIRQ.
This is wrong because TIMER_SOFTIRQ is the softirq number and not a
bitmask. So the test checks for the wrong bit.
Use BIT(TIMER_SOFTIRQ) instead.
Fixes: 5d62c183f9 ("nohz: Prevent a timer interrupt storm in tick_nohz_stop_sched_tick()")
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Cc: bigeasy@linutronix.de
Cc: peterz@infradead.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180731161358.29472-1-anna-maria@linutronix.de
After introduction of the cited commit, mlx5e_build_nic_params
receives the netdevice mtu in order to set the sw_mtu of mlx5e_params.
For enhanced IPoIB, the netdevice mtu is not set in this stage,
therefore, the initial sw_mtu equals zero. As a result, the hw_mtu
of the receive queue will be calculated incorrectly causing traffic
issues.
To fix this issue, query for port mtu before building the nic params.
Fixes: 472a1e44b3 ("net/mlx5e: Save MTU in channels params")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MTU helper function is used by both conventional mlx5e
instances (PF/VF) and the eswitch representors. The representor
shouldn't change the nic vport context MTU, the VF is responsible for
that. Therefore set_mtu_cb has a null value when changing the
representor MTU.
Fixes: 250a42b6a7 ("net/mlx5e: Support configurable MTU for vport representors")
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The hairpin offload code has dependency on the trust mode being PCP.
Hence we should set PCP as the default for handling cases where we are
disallowed to read the trust mode from the FW, or failed to initialize it.
Fixes: 106be53b6b ('net/mlx5e: Set per priority hairpin pairs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Execute mlx5_eswitch_init() only if we have MLX5_ESWITCH_MANAGER
capabilities.
Do the same for mlx5_eswitch_cleanup().
Fixes: a9f7705ffd ("net/mlx5: Unify vport manager capability check")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We never use RCU protection for it, just a lot of cargo-cult
rcu_deference_protects calls.
Note that we do keep the kfree_rcu call for it, as the references through
struct sock are RCU protected and thus might require a grace period before
freeing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version 1 of the patch adding SERDES support to the 88E6141/6341
correctly added the ops to the 88E6141/6341. However, by the time
version 3 was committed, the ops had moved to the 88E6085/6175. Put
them back where they belong.
Fixes: 5bafeb6e7e ("net: dsa: mv88e6xxx: 88E6141/6341 SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last set of fixes before 4.18 is released
iwlwifi
* add new IDs for cards already available on the market
brcmfmac
* fix a regression introduced in v4.17
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbYDWEAAoJEG4XJFUm622bPGUH+QHGcuazgPqR4TsQXwmfNdJB
HJdsx90WW6TLMDzF9EquA4ontBggq2Mdnorxt1SIXK+ZeajFWZlKyl5ol24TtOH3
9uFhQRID2KlWPnwgrBTsFAiNNJar+X4GoUX1SqFz8VJnkYgfdtBHaVK59HdWSp5e
2rVaG/ORUMNnY58f6jr9wOhn/miC1CKuJk5j83CN2KlETkqj/VoGUE2dShdJl0wu
+4iYznIwhG9f6KykReaBmJbh4xu6AEqkFbadKGwWcChR3DDmzDAsWzkcWEocx8ZY
EpoF6vW8GoBB2RE2Syg/Y6exQGnDb4itYQYxvJV1qV52XwYfvDzCdlbLn+kv34I=
=4wJj
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.18
Last set of fixes before 4.18 is released
iwlwifi
* add new IDs for cards already available on the market
brcmfmac
* fix a regression introduced in v4.17
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't maintain tx counters in rx stats any more. There's no need
for an extra container of rq stats.
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5b8f3c8d30 ("virtio_net: Add XDP related stats") tries to
count TX XDP stats in virtnet_receive(). This will cause several
issues:
- virtnet_xdp_sq() was called without checking whether or not XDP is
set. This may cause out of bound access when there's no enough txq
for XDP.
- Stats were updated even if there's no XDP/XDP_TX.
Fixing this by reusing virtnet_xdp_xmit() for XDP_TX which can counts
TX XDP counter itself and remove the unnecessary tx stats embedded in
rx stats.
Reported-by: syzbot+604f8271211546f5b3c7@syzkaller.appspotmail.com
Fixes: 5b8f3c8d30 ("virtio_net: Add XDP related stats")
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
xsk: improvements to RX queue check and replace
First 3 patches of my recent RFC. The first one make the check against
real_num_rx_queues slightly more reliable, while the latter two redefine
XDP_QUERY_XSK_UMEM slightly to disallow replacing UMEM in the driver at
the stack level.
I'm not sure where this lays on the bpf vs net trees scale, but there
should be no conflicts with either tree.
====================
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drivers have to check if they already have a umem
installed for a given queue and return an error if so. Make
better use of XDP_QUERY_XSK_UMEM and move this functionality
to the core.
We need to keep rtnl across the calls now.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
