When attaching an imx28 or imx53 in USB gadget mode to a Windows host and
starting a rndis connection we see this message every 4-10 seconds:
g_ether gadget: high speed config #2: RNDIS
Analysis shows that each time this message is printed, the rndis connection is
re-establish due to a reset because of a stalled endpoint (ep 0, dir 1). The
endpoint is stalled because the reqeust complete bit on that endpoint is set,
but in isr_tr_complete_low() the endpoint request list (mEp->qh.queue) is
empty.
This patch removed this check, because the code doesn't take the following
situation into account:
The loop over all endpoints in isr_tr_complete_handler() will call ep_nuke() on
both ep0/dir0 and ep/dir1 in the first loop. Pending reqeusts will be flushed
and completed here. There seems to be a race condition, the request is nuked,
but the request complete bit will be set, too. The subsequent check (in
ep0/dir1's loop cycle) for endpoint request list (mEp->qh.queue) empty will
fail.
Both other mainline chipidea drivers (mv_udc_core.c and fsl_udc_core.c) don't
have this check.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If udc_start() fails the qh_pool dma-pool cannot be closed because
it's still in use. This patch factors out the dma_pool_free() loop
into destroy_eps() and calls it in the error path of udc_start(),
too.
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the error path of udc_start(). Now NULL is used to
unset the peripheral with otg_set_peripheral().
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add function to physicaly enable or disable of pullup connection on the USB-D+
line. The uvc gaget will fail, if this function is not implemented.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the setup of the endpoint maxpacket size. All non control
endpoints are initialized with an undefined ((unsigned short)~0) maxpacket
size. The maxpacket size of Endpoint 0 will be kept at CTRL_PAYLOAD_MAX.
Some gadget drivers check for the maxpacket size before they enable the
endpoint, which leads to a wrong state in these drivers.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possibility of QH overlay region having reference to a stale
qTD pointer during unlink.
Consider an endpoint having two pending qTD before unlink process begins.
The endpoint's QH queue looks like this.
qTD1 --> qTD2 --> Dummy
To unlink qTD2, QH is removed from asynchronous list and Asynchronous
Advance Doorbell is programmed. The qTD1's next qTD pointer is set to
qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell
interrupt. If QH's current qTD pointer points to qTD1, transfer overlay
region still have reference to qTD2. But qtD2 is just unlinked and freed.
This may cause EHCI system error. Fix this by updating qTD next pointer
in QH overlay region with the qTD next pointer of the current qTD.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A logic error made the wdm_find_device* functions
return a bogus pointer into static data instead of
the intended NULL no matching device was found.
Cc: stable <stable@vger.kernel.org> # v3.4+
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Microchip vid:pid 04d8:000a is used for their CDC ACM
demo firmware application. This is a device with a single
function conforming to the CDC ACM specification and with
the intention of demonstrating CDC ACM class firmware and
driver interaction. The demo is used on a number of
development boards, and may also be used unmodified by
vendors using Microchip hardware.
Some vendors have re-used this vid:pid for other types of
firmware, emulating FTDI chips. Attempting to continue to
support such devices without breaking class based
applications that by matching on interface
class/subclass/proto being ff/ff/00. I have no information
about the actual device or interface descriptors, but this
will at least make the proper CDC ACM devices work again.
Anyone having details of the offending device's descriptors
should update this entry with the details.
Reported-by: Florian Wöhrl <fw@woehrl.biz>
Reported-by: Xiaofan Chen <xiaofanc@gmail.com>
Cc: stable <stable@vger.kernel.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a rather big set of fixes for v3.6-rc4.
There are some fixes for bugs which have been pending for a long
time and only now were uncovered, like the musb and dwc3 patches.
We have some remaining fixes for the ep->desc patch series from
Ido, a fix for renesas DMA usage, IRQ check on musb's DMA and
an oops fix on musb Host implementation.
All patches have been pending on linux-usb for a long time and
shouldn't cause any further regressions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F4Vw
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into work-linus
usb: fixes for v3.6-rc4
Here's a rather big set of fixes for v3.6-rc4.
There are some fixes for bugs which have been pending for a long
time and only now were uncovered, like the musb and dwc3 patches.
We have some remaining fixes for the ep->desc patch series from
Ido, a fix for renesas DMA usage, IRQ check on musb's DMA and
an oops fix on musb Host implementation.
All patches have been pending on linux-usb for a long time and
shouldn't cause any further regressions.
If xfernotready is received and there is no request in request_list then
REQUEST_PENDING flag must be set, so that next request in ep queue is executed.
In case of isoc transfer, if xfernotready is already elapsed and even first
request has not been queued to request_list, then issue END TRANSFER, so that
you can receive xfernotready again and can have notion of current microframe.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs dma can transport 8byte alignment data, not 4byte.
This patch fixup it.
Reported-by: Sugnan Prabhu S <sugnan.prabhu@renesasmobile.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Earlier we used to check for ep->ep.desc to figure out if this ep has
already been enabled and if so, abort.
Ido Shayevitz removed the usb_endpoint_descriptor from private udc
structure 5a6506f00 ("usb: gadget: Update at91_udc to use
usb_endpoint_descriptor inside the struct usb_ep") but did not fix up
the ep_enable condition because _now_ the member is always true and we
can't check if this ep is enabled twice.
Cc: Ido Shayevitz <idos@codeaurora.org>
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt>
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The driver was converted to the new start/stop interface in f3d8bf34c2
("usb: gadget: at91_udc: convert to new style start/stop interface").
I overlooked that the driver is overwritting the private data which is
used by the composite framework. The udc driver doesn't read it, it is
only written here.
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt>
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Populate the resources for xhci afresh instead of directly using the
*struct resource* of core. *resource* structure has parent, sibling,
child pointers which should be filled only by resource API's. By
directly using the *resource* pointer of core in xhci, these parent,
sibling, child pointers are already populated even before
*platform_device_add* causing side effects.
Cc: stable@vger.kernel.org # v3.4, v3.5
Reported-by: Ruchika Kharwar <ruchika@ti.com>
Tested-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dma_controller_create() in this MUSB DMA driver only regards 0 as a wrong IRQ
number, despite platform_get_irq_byname() that it calls returns -ENXIO in that
case. It leads to calling request_irq() with a negative IRQ number, and when it
naturally fails, the following is printed to the console:
request_irq -6 failed!
and the DMA controller is not created.
Fix this function to filter out the error values as well as 0.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On platform_device_add() failure, the TUSB6010 glue layer forgets to call
platform_device_put() -- probably due to a typo...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
when using musb_urb_enqueue to submit three urbs to the same endpoint, when
hep->hcpriv is NULL, qh will be allocated when the first urb is completed.
When the IRQ completes the next two urbs, qh->hep->hcpriv will be set to NULL.
Now the second urb get musb->lock and executes musb_schedule(), but
next_urb(qh) is NULL, so musb_start_urb will Oops.
[ balbi@ti.com : practically rewrote commit log so it makes sense ]
Signed-off-by: mayuzheng <myz147@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without a reply for USB_DT_BOS the USB3 mode does not work since
448b6eb1 ("USB: Make sure to fetch the BOS desc for roothubs.).
Cc: stable@vger.kernel.org #v3.5
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If USB2 host controller probes fine but USB3 does not then we don't
remove the USB controller properly and lock up the system while the HUB
code will try to enumerate the USB2 controller and access memory which
is no longer available in case the dummy_hcd was compiled as a module.
This is a problem since 448b6eb1 ("USB: Make sure to fetch the BOS desc
for roothubs.) if used in USB3 mode because dummy does not provide this
descriptor and explodes later.
Cc: stable@vger.kernel.org # v3.5
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of ep0 out, if length is not aligned to maxpacket size then we use
dwc->ep_bounce_addr for dma transfer and not request->dma. Since, we have
alreday done memcpy from dwc->ep0_bounce to request->buf, so we do not need to
issue cache sync function. In fact, cache sync function will bring wrong data
in request->buf from request->dma in this scenario.
So, cache sync function must not be executed in case of ep0 bounced.
Cc: <stable@vger.kernel.org> # v3.4 v3.5
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If f_fs.c and u_serial.c are combined together using #include, which has
been a common practice so far, the pr_vdebug macro is defined multiple
times. Define it only once.
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Hi Greg,
Here's seven bugfixes for 3.6. All of them are marked for stable, and
most are vendor-specific fixes.
Details:
--------
- Commits 052c7f9 and 2963657 fix a couple stupid mistakes I made in a
Intel xHCI bug fix patch I pushed just before I left for vacation.
- Commits 29d2145 and a96874a fix issues with the Intel Panther Point
EHCI to xHCI port switchover.
- Commit 71c731a adds the work-around for the TI redriver "dead port"
issue.
- Commit 319acdf adds a fix for non-PCI xHCI platform drivers.
- Commit e955a1c works around the UEFI issue with the xHCI host
sometimes returning 0xff's in the MMIO on boot.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=124d
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-09-05' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xHCI 3.6 bug fixes.
Hi Greg,
Here's seven bugfixes for 3.6. All of them are marked for stable, and
most are vendor-specific fixes.
Details:
--------
- Commits 052c7f9 and 2963657 fix a couple stupid mistakes I made in a
Intel xHCI bug fix patch I pushed just before I left for vacation.
- Commits 29d2145 and a96874a fix issues with the Intel Panther Point
EHCI to xHCI port switchover.
- Commit 71c731a adds the work-around for the TI redriver "dead port"
issue.
- Commit 319acdf adds a fix for non-PCI xHCI platform drivers.
- Commit e955a1c works around the UEFI issue with the xHCI host
sometimes returning 0xff's in the MMIO on boot.
Sarah Sharp
This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss
infrared touchboard device. The device doesn't like to be asked for
its interface strings.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: adam ? <adam3337@wp.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the number of ports present on the SoC/board is not the maximum
and that the platform data is not filled with all data, there is
an easy way to mess the PIO setup for this interface.
This quick fix addresses mis-configuration in USB host platform data
that is common in at91 boards since commit 0ee6d1e (USB: ohci-at91:
change maximum number of ports) that did not modified the associatd
board files.
Reported-by: Klaus Falkner <klaus.falkner@solectrix.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Stable <stable@vger.kernel.org> [3.4+]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the USB PID for the NZR SEM 16+ USB energy monitor device
<http://www.nzr.de>. It works perfectly with the GPL software on
<http://schou.dk/linux/sparometer/>.
Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b69cc67205 added support for the E-861. After acquiring a C-867, I
realised that every Physik Instrumente's device has a different PID. They are
listed in the Windows device driver's .inf file. So here are all PIDs for the
current (and probably future) USB devices from Physik Instrumente.
Compiled, but only actually tested on the E-861 and C-867.
Signed-off-by: Éric Piel <piel@delmic.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.
Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.
[ balbi@ti.com: slight improvement to commit log ]
This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f474 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.
Signed-off-by: Moiz Sonasath<m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Use the ioremap_nocache variant of the ioremap API in
order to make sure our memory will be marked uncachable.
This patch should be backported to kernels as old as 3.4, that contain
the commit 3429e91a66 "usb: host: xhci:
add platform driver support".
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch is intended to work around a known issue on the
SN65LVPE502CP USB3.0 re-driver that can delay the negotiation
between a device and the host past the usual handshake timeout.
If that happens on the first insertion, the host controller
port will enter in Compliance Mode and NO port status event will
be generated (as per xHCI Spec) making impossible to detect this
event by software. The port will remain in compliance mode until
a warm reset is applied to it.
As a result of this, the port will seem "dead" to the user and no
device connections or disconnections will be detected.
For solving this, the patch creates a timer which polls every 2
seconds the link state of each host controller's port (this
by reading the PORTSC register) and recovers the port by issuing a
Warm reset every time Compliance mode is detected.
If a xHC USB3.0 port has previously entered to U0, the compliance
mode issue will NOT occur only until system resumes from
sleep/hibernate, therefore, the compliance mode timer is stopped
when all xHC USB 3.0 ports have entered U0. The timer is initialized
again after each system resume.
Since the issue is being caused by a piece of hardware, the timer
will be enabled ONLY on those systems that have the SN65LVPE502CP
installed (this patch uses DMI strings for detecting those systems)
therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK
has been added to the xhci stack).
This patch applies for these systems:
Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820.
This patch should be backported to kernels as old as 3.2, as that was
the first kernel to support warm reset. The kernels will need to
contain both commit 10d674a82e "USB: When
hot reset for USB3 fails, try warm reset" and commit
8bea2bd37d "usb: Add support for root hub
port status CAS". The first patch add warm reset support, and the
second patch modifies the USB core to issue a warm reset when the port
is in compliance mode.
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.
I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.
This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd8d "USB: xhci: BIOS handoff
and HW initialization."
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The intent was to test whether the flag was set.
This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f474 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
With a previous patch to enable the EHCI/XHCI port switching, it switches
all the available ports.
The assumption is not correct because the BIOS may expect some ports
not switchable by the OS.
There are two more registers that contains the information of the switchable
and non-switchable ports.
This patch adds the checking code for the two register so that only the
switchable ports are altered.
This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
On Intel Panther Point chipset USB 3.0 devices show up as
high-speed devices on powerup, but after an s3 cycle they are
correctly recognized as SuperSpeed. At powerup switch the port
to xHCI so that USB 3.0 devices are correctly recognized.
BugLink: http://bugs.launchpad.net/bugs/1000424
This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Here are 10 more USB patches for 3.6-rc3. They all fix reported
problems (build problems for one of them, and easily repeatable oopses
for the others.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAyjj4ACgkQMUfUDdst+yn8gQCgkNpc92Ux5hBYJIX/AQYoBrTB
ktAAoLiXxIhVP+D4C42R1VLw9vGeB1QH
=+8kb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull more USB patches from Greg Kroah-Hartman:
"Here are 10 more USB patches for 3.6-rc3. They all fix reported
problems (build problems for one of them, and easily repeatable oopses
for the others.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
gpu/mfd/usb: Fix USB randconfig problems
USB: CDC ACM: Fix NULL pointer dereference
USB: emi62: remove __devinit* from the struct usb_device_id table
USB: winbond: remove __devinit* from the struct usb_device_id table
USB: vt6656: remove __devinit* from the struct usb_device_id table
USB: rtl8187: remove __devinit* from the struct usb_device_id table
USB: p54usb: remove __devinit* from the struct usb_device_id table
USB: spca506: remove __devinit* from the struct usb_device_id table
USB: jl2005bcd: remove __devinit* from the struct usb_device_id table
USB: smsusb: remove __devinit* from the struct usb_device_id table
Fix config warning:
warning: ( ... && DRM_USB) selects USB which has unmet direct dependencies
(USB_SUPPORT && USB_ARCH_HAS_HCD)
and build error:
ERROR: "usb_speed_string" [drivers/usb/core/usbcore.ko] undefined!
by adding the missing dependency on USB_ARCH_HAS_HCD to DRM_UDL and DRM_USB.
This exposes:
drivers/video/Kconfig:36:error: recursive dependency detected!
drivers/video/Kconfig:36: symbol FB is selected by DRM_KMS_HELPER
drivers/gpu/drm/Kconfig:28: symbol DRM_KMS_HELPER is selected by DRM_UDL
drivers/gpu/drm/udl/Kconfig:1: symbol DRM_UDL depends on USB_ARCH_HAS_HCD
drivers/usb/Kconfig:78: symbol USB_ARCH_HAS_HCD depends on USB_ARCH_HAS_OHCI
drivers/usb/Kconfig:16: symbol USB_ARCH_HAS_OHCI depends on I2C
drivers/i2c/Kconfig:5: symbol I2C is selected by FB_DDC
drivers/video/Kconfig:86: symbol FB_DDC is selected by FB_CYBER2000_DDC
drivers/video/Kconfig:385: symbol FB_CYBER2000_DDC depends on FB_CYBER2000
drivers/video/Kconfig:373: symbol FB_CYBER2000 depends on FB
which is due to drivers/usb/Kconfig:
config USB_ARCH_HAS_OHCI
...
default y if ARCH_PNX4008 && I2C
Fix by dropping I2C from the above dependency; logic is that this is not a
platform dependency but a configuration dependency: the _architecture_ still
supports USB even is I2C is not selected.
This exposes:
drivers/video/Kconfig:36:error: recursive dependency detected!
drivers/video/Kconfig:36: symbol FB is selected by DRM_KMS_HELPER
drivers/gpu/drm/Kconfig:28: symbol DRM_KMS_HELPER is selected by DRM_UDL
drivers/gpu/drm/udl/Kconfig:1: symbol DRM_UDL depends on USB_ARCH_HAS_HCD
drivers/usb/Kconfig:78: symbol USB_ARCH_HAS_HCD depends on USB_ARCH_HAS_OHCI
drivers/usb/Kconfig:17: symbol USB_ARCH_HAS_OHCI depends on MFD_TC6393XB
drivers/mfd/Kconfig:396: symbol MFD_TC6393XB depends on GPIOLIB
drivers/gpio/Kconfig:35: symbol GPIOLIB is selected by FB_VIA
drivers/video/Kconfig:1560: symbol FB_VIA depends on FB
which can be fixed by having MFD_TC6393XB select GPIOLIB instead of depending on
it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device specifies zero endpoints in its interface descriptor,
the kernel oopses in acm_probe(). Even though that's clearly an
invalid descriptor, we should test wether we have all endpoints.
This is especially bad as this oops can be triggered by just
plugging a USB device in.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a number of small USB patches for 3.6-rc3. The "large" one is just a
number of device id updates to the option driver, done by the manufacturer,
properly fixing up the device ids based on shipping devices. Other than that,
some gadget driver fixes, the obligitary XHCI patches, and some other device
ids and bugs fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAuedoACgkQMUfUDdst+yl2DwCgzuMNDjzik/MKCTTCYARznsJ0
QIwAoMOGh+7xvCNYf9Cp8MMr/mmHZmF3
=ZEBb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are a number of small USB patches for 3.6-rc3.
The "large" one is just a number of device id updates to the option
driver, done by the manufacturer, properly fixing up the device ids
based on shipping devices.
Other than that, some gadget driver fixes, the obligitary XHCI
patches, and some other device ids and bugs fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: qcserial: fix port handling on Gobi 1K and 2K+
USB: serial: Fix mos7840 timeout
USB: option: add ZTE K5006-Z
usb: gadget: u_ether: fix kworker 100% CPU issue with still used interfaces in eth_stop
usb: host: tegra: fix warning messages in ehci_remove
usb: host: mips: sead3: Update for EHCI register structure.
usb: renesas_usbhs: fixup resume method for autonomy mode
usb: renesas_usbhs: mod_host: add missing .bus_suspend/resume
update MAINTAINERS for Oliver Neukum
usb: usb_wwan: resume/suspend can be called after port is gone
usb: serial: prevent suspend/resume from racing against probe/remove
usb: usb_wwan: replace release and disconnect with a port_remove hook
usb: serial: mos7840: Fixup mos7840_chars_in_buffer()
USB: isp1362-hcd.c: usb message always saved in case of underrun
OMAP: USB : Fix the EHCI enumeration and core retention issue
usb: chipidea: fix and improve dependencies if usb host or gadget support is built as module
USB: support the new interfaces of Huawei Data Card devices in option driver
USB: ftdi_sio: Add VID/PID for Kondo Serial USB
xhci: Switch PPT ports to EHCI on shutdown.
xhci: Fix bug after deq ptr set to link TRB.
...
Bjorn's latest patchset does break Gobi 1K and 2K because on both
devices as it claims usb interface 0. That's because usbif 0 is not
handled in the switch statement, and thus the if0 gets claimed when it
should not. So let's just make things even simpler yet, and handle both
the 1K and 2K+ cases separately. This patch should not affect the new
Sierra device support, because those devices are matched via
interface-specific matching and thus should never hit the composite
code.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mos7840 driver was using multiple of HZ for the timeout handed off to
usb_control_msg(). Changed the timeout to use msecs instead.
* Remove unused WAIT_FOR_EVER definition
Signed-off-by: Mark Ferrell <mferrell@uplogix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ZTE (Vodafone) K5006-Z use the following
interface layout:
00 DIAG
01 secondary
02 modem
03 networkcard
04 storage
Ignoring interface #3 which is handled by the qmi_wwan
driver.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are a bunch of bug fixes that came in after the merge window and
one update for the MAINTAINERS file. The largest part of the fixes
are patches that address bugs found by building all the ARM defconfig
files. There are a lot more warnings that we have patches for, but
the others are either still under discussion or are harmless and
do not cause actual problems besides making the build slightly noisy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=TmsX
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Arnd Bergmann:
"These are a bunch of bug fixes that came in after the merge window and
one update for the MAINTAINERS file.
The largest part of the fixes are patches that address bugs found by
building all the ARM defconfig files. There are a lot more warnings
that we have patches for, but the others are either still under
discussion or are harmless and do not cause actual problems besides
making the build slightly noisy."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: davinci: remove broken ntosd2_init_i2c
ARM: s3c24xx: enable CONFIG_BUG for tct_hammer
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
ARM: imx: gpmi-nand depends on mxs-dma
ARM: integrator: include <linux/export.h>
ARM: s3c24xx: use new PWM driver
ARM: sa1100: include linux/io.h in hackkit leds code
Input: eeti_ts: pass gpio value instead of IRQ
ARM: pxa: remove irq_to_gpio from ezx-pcap driver
ARM: tegra: more regulator fixes for Harmony
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
ARM: kirkwood: fix typo in Makefile.boot
i.MX27: Fix emma-prp and csi clocks.
ARM: integrator: use clk_prepare_enable() for timer
MAINTAINERS: update entry for Linus Walleij
...
This patch fixes an issue introduced by patch:
72c973d usb: gadget: add usb_endpoint_descriptor to struct usb_ep
Without this patch we see a kworker taking 100% CPU, after this sequence:
- Connect gadget to a windows host
- load g_ether
- ifconfig up <ip>; ifconfig down; ifconfig up
- ping <windows host>
The "ifconfig down" results in calling eth_stop(), which will call
usb_ep_disable() and, if the carrier is still ok, usb_ep_enable():
usb_ep_disable(link->in_ep);
usb_ep_disable(link->out_ep);
if (netif_carrier_ok(net)) {
usb_ep_enable(link->in_ep);
usb_ep_enable(link->out_ep);
}
The ep should stay enabled, but will not, as ep_disable set the desc
pointer to NULL, therefore the subsequent ep_enable will fail. This leads
to permanent rescheduling of the eth_work() worker as usb_ep_queue()
(called by the worker) will fail due to the unconfigured endpoint.
We fix this issue by saving the ep descriptors and re-assign them before
usb_ep_enable().
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing implementation of tegra_ehci_remove() calls
usb_put_hcd(hcd) first and then iounmap(hcd->regs).
usb_put_hcd() implementation calls hcd_release()
which frees up memory allocated for hcd.
As iounmap is trying to unmap hcd->regs, after hcd
getting freed up, warning messages were observed during
unload of USB.
Hence fixing it.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One line fix after 'struct ehci_regs' definition was changed
in commit a46af4ebf9 (USB: EHCI: define
extension registers like normal ones).
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If renesas_usbhs is probed as autonomy mode,
phy reset should be called after power resumed,
and manual cold-plug should be called with slight delay.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
suspend/resume will failed on renesas_usbhs without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
