Trivial fix to spelling mistake in MFD headers.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the function ab8500_fg_reinit() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Make ab8500_btemp_get_temp interface public, export it and also export the
ab8500_btemp_get, ab8500_btemp_get_batctrl_temp interfaces, so that the
ab8500 hwmon driver can use them.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
When the state of USB Charge detection is changed then the calls
use a define for another register in other bank. This change
creates a new define for the correct register and removes the
magic numbers that are present.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Provide AB8540 platform specific information required to run the
Battery Management subsystem on AB8540 based devices. For this to
happen we see the introduction of separate platform specific data
structures and a means in which to process them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
AB8540 supports power path function in USB charging mode for fast
power up with dead and weak battery, and it could extend
the battery age.
When USB charging starts, if the Vbattrue is below than SW cut off
voltage, power path and pre-charge should be enabled. If Vbattrue
is higher than SW cut off voltage, power path and pre-charge should
be disabled. This is to make sure full current to battery charge.
At the end of charge, power path should be enable again to reduce
charging the battery again.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add 2.7v, 2.9v, 3.0v, 3.2v and 3.3v charging voltages for backup
battery. Before that only 2.5v, 2.6v, 2.8v, 3.1v were available.
Signed-off-by: Yang QU <yang.qu@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Maxime COQUELIN <maxime.coquelin@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Tested-by: Xiao Mei ZHANG <xiaomei.zhang@stericsson.com>
Add support for a power cut feature which allows user to
configure when ab8505 and ab8540 based platforms should shut
down system due to low battery.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
o goldfish_battery:
This is Android Emulator battery driver. Originally from Google, but
Intel folks reshaped it for mainline;
o pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses AB8500
battery management core;
o qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes;
o restart-poweroff:
A generic driver that implements 'power off by restarting'. The actual
poweroff functionality is implemented through a bootloader, so Linux'
task is just to restart the box. The driver is useful on Buffalo
Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked on
submitting the driver (as well as qnap-poweroff above).
- A lot of fixes for ab8500 drivers. This is a part of efforts of syncing
internal ST-Ericsson development tree with the mainline. Lee Jones @
Linaro worked on compilation and reshaping these series;
- New health properties for the power supplies: "Watchdog timer expire"
and "Safety timer expire";
- As usual, a bunch of fixes/cleanups here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJRIww1AAoJEGgI9fZJve1bJ7sP/1hR8SYQZ/k0ayxA/kIxNEDA
Qa2sAcdP5pa4F/A2Wi5MTrckSHuLlRRigWRCPM09emVOvt6g2MdM3Eq6ShuYb2p0
g2bX0F9KBEa9gdiJC1wNVe9DilXbrJsk86V5E+ZkuVnNzM3S1FA1sPWGhdH66YVq
9IKxm2XntyXFpuvhSYE01KQoFY+Crv1NEGXoIR7tB6Q1KOf3XswnsFwdKJ95IO5r
8f/lVYRAYUfeplhrYd3eJTtb/GHhK7CutFV/E6kWlumGCWNVH2xt+dTlAmTUdQvO
jKe9R5iq5eXFTQmN8QZDH7QdXO1DdmJZ9F112hIAud/93bmNrnc0WqMKM7CFHkfH
S6ptGgeIdpGEM1KMgzKTNrQeNIYsVNtqbEiIiodR8S4e0cX2pb2n5IfzmELIVc0n
QMZylORpGaH1lBxTE2RoT4raGeWF5jH0t0b0YRqccRPvQ4VjCJslDOq9IOETUe+/
YxWpELJigW7FGLMfx0SB2/3s1P4EUaufWvHANCVaPuBsOZga854R4dzms4hKyKsL
JQg+OKp/Bt78yAj/8/n0FWdxgldp/NjF4485ITQ1eOZyg8VSeIp93Lk6lgSTukux
R1xLruxfPgdynpmYFCGF99JG2G8RmRuJFSTf8JttvyztkAxQw6zBtdmdiPk38wst
qpUxdPpNDIvt65Ix7x+D
=955B
-----END PGP SIGNATURE-----
Merge tag 'for-v3.9' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Four new drivers:
- goldfish_battery:
This is Android Emulator battery driver. Originally from Google,
but Intel folks reshaped it for mainline
- pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses
AB8500 battery management core
- qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes
- restart-poweroff:
A generic driver that implements 'power off by restarting'. The
actual poweroff functionality is implemented through a bootloader,
so Linux' task is just to restart the box. The driver is useful on
Buffalo Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked
on submitting the driver (as well as qnap-poweroff above).
Additionally:
- A lot of fixes for ab8500 drivers. This is a part of efforts of
syncing internal ST-Ericsson development tree with the mainline.
Lee Jones @ Linaro worked on compilation and reshaping these
series.
- New health properties for the power supplies: "Watchdog timer
expire" and "Safety timer expire"
- As usual, a bunch of fixes/cleanups here and there"
* tag 'for-v3.9' of git://git.infradead.org/battery-2.6: (81 commits)
bq2415x_charger: Add support for offline and 100mA mode
generic-adc-battery: Fix forever loop in gab_remove()
goldfish_battery: Add missing GENERIC_HARDIRQS dependency
da9030_battery: Include notifier.h
bq27x00_battery: Fix reporting battery temperature
power/reset: Remove newly introduced __dev* annotations
lp8727_charger: Small cleanup in naming
ab8500_btemp: Demote initcall sequence
ds2782_battery: Add power_supply_changed() calls for proper uevent support
power: Add battery driver for goldfish emulator
u8500-charger: Delay for USB enumeration
ab8500-bm: Remove individual [charger|btemp|fg|chargalg] pdata structures
ab8500-charger: Do not touch VBUSOVV bits
ab8500-fg: Use correct battery charge full design
pm2301: LPN mode control support
pm2301: Enable vbat low monitoring
ab8500-bm: Flush all work queues before suspending
ab8500-fg: Go to INIT_RECOVERY when charger removed
ab8500-charger: Add support for autopower on AB8505 and AB9540
abx500-chargalg: Add new sysfs interface to get current charge status
...
Fix up fairly straightforward conflicts in the ab8500 driver. But since
it seems to be ARM-specific, I can't even compile-test the result..
None of the aforementioned components have their own dedicated
platform data structures anymore. Instead they have all been
merged into one big Battery Management container. Let's remove
them and place all the nice newly added attributes into the core
container.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add AB9540 and AB8505 support to ABx500 BTEMP driver.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
AC charger driver for the DB9540 based platforms.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
drivers/mfd/ab8500-core.c:1015:21: error: ‘ab8500_bm_data’ undeclared here
include/linux/mfd/abx500/ab8500-bm.h:445:13: warning: ‘ab8500_fg_reinit’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:448:13: warning: ‘ab8500_charger_usb_state_changed’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:451:29: warning: ‘ab8500_btemp_get’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:455:12: warning: ‘ab8500_btemp_get_batctrl_temp’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:463:12: warning: ‘ab8500_fg_inst_curr_blocking’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:442:12: warning: ‘ab8500_fg_inst_curr_done’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:447:26: warning: ‘ab8500_fg_get’ defined but not used
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Travel and Carkit adapter should be handled directly by
the charger driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Today the battery recharge is determined with a voltage threshold. This
voltage threshold is only valid when the battery is relaxed. In charging
algorithm the voltage read is the loaded battery voltage and no
compensation is done to get the relaxed voltage. When maintenance
charging is not selected, this makes the recharging condition to almost
immediately activate when there is a discharge present on the battery.
Depending on which vendor the battery comes from this behavior can wear
out the battery much faster than normal.
The fuelgauge driver is responsible to monitor the actual battery
capacity and is able to estimate the remaining capacity. It is better to
use the remaining capacity as a limit to determine when battery should
be recharged.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
When enabling the CCEOC irq we might get false interrupt
from ab8500-driver due to the latched value will be saved
and interpreted as an IRQ when enabled
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Johan Bjornstedt <johan.bjornstedt@stericsson.com>
Signed-off-by: Henrik Solver <henrik.solver@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The struct is duplicated, plus causes the following flood:
CC drivers/power/ab8500_fg.o
ab8500_fg.c: In function ‘ab8500_fg_get_ext_psy_data’:
b8500_fg.c:2081:8: warning: assignment from incompatible pointer type [enabled by default]
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The struct is duplicated, plus when used it causes the following
warnings:
CHECK drivers/power/ab8500_fg.c
ab8500_fg.c:818:13: warning: incorrect type in assignment (different base types)
ab8500_fg.c:818:13: expected struct v_to_cap *tbl
ab8500_fg.c:818:13: got struct abx500_v_to_cap *const v_to_cap_tbl
CC drivers/power/ab8500_fg.o
ab8500_fg.c: In function 'ab8500_fg_volt_to_capacity':
ab8500_fg.c:818:6: warning: assignment from incompatible pointer type [enabled by default]
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This is the same as abx500_adc_therm, but when the former is used,
the following warning flood pops up:
drivers/power/ab8500_btemp.c: In function 'ab8500_btemp_batctrl_volt_to_res':
ab8500_btemp.c:150:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c: In function 'ab8500_btemp_curr_source_enable':
ab8500_btemp.c:212:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c:244:32: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c: In function 'ab8500_btemp_measure_temp':
ab8500_btemp.c:462:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c: In function 'ab8500_btemp_id':
ab8500_btemp.c:528:121: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c:551:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
This patch fixes the issue by switching the driver to use more
namespace-friendly enum.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This driver is responsible for detecting the ac/usb plugin and also includes
function to enable ac/usb charging and re-kick the watchdog.
It registers with the power supply class and provides information to the user
space. The information include status of ac/usb charger device.
This information in turn will be used by the abx500 charging algorithm driver
to enable/disable and monitor charging.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
