Do DMAFLUSHP _before_ the first DMAWFP to ensure controller
and peripheral are in agreement about dma request state before first
transfer. Add support for burst transfers to/from peripherals. In the new
scheme, the controller does as many burst transfers as it can then
transfers the remaining dregs with either single transfers for
peripherals, or with a reduced size burst for memory-to-memory transfers.
Signed-off-by: Frank Mori Hess <fmh6jj@gmail.com>
Tested-by: Frank Mori Hess <fmh6jj@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If two concurrent threads call pl330_get_desc() when DMAC descriptor
pool is empty it is possible that allocation for one of threads will fail
with message:
kernel: dma-pl330 20078000.dma-controller: pl330_get_desc:2469 ALERT!
Here how that can happen. Thread A calls pl330_get_desc() to get
descriptor. If DMAC descriptor pool is empty pl330_get_desc() allocates
new descriptor on shared pool using add_desc() and then get newly
allocated descriptor using pluck_desc(). At the same time thread B calls
pluck_desc() and take newly allocated descriptor. In that case descriptor
allocation for thread A will fail.
Using on-stack pool for new descriptor allow avoid the issue described.
The patch modify pl330_get_desc() to use on-stack pool for allocation
new descriptors.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
- removal of AVR32 support in dw driver as AVR32 is gone
- new driver for Broadcom stream buffer accelerator (SBA) RAID driver
- add support for Faraday Technology FTDMAC020 in amba-pl08x driver
- IOMMU support in pl330 driver
- updates to bunch of drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=srPZ
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.13-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- removal of AVR32 support in dw driver as AVR32 is gone
- new driver for Broadcom stream buffer accelerator (SBA) RAID driver
- add support for Faraday Technology FTDMAC020 in amba-pl08x driver
- IOMMU support in pl330 driver
- updates to bunch of drivers
* tag 'dmaengine-4.13-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (36 commits)
dmaengine: qcom_hidma: correct API violation for submit
dmaengine: zynqmp_dma: Remove max len check in zynqmp_dma_prep_memcpy
dmaengine: tegra-apb: Really fix runtime-pm usage
dmaengine: fsl_raid: make of_device_ids const.
dmaengine: qcom_hidma: allow ACPI/DT parameters to be overridden
dmaengine: fsldma: set BWC, DAHTS and SAHTS values correctly
dmaengine: Kconfig: Simplify the help text for MXS_DMA
dmaengine: pl330: Delete unused functions
dmaengine: Replace WARN_TAINT_ONCE() with pr_warn_once()
dmaengine: Kconfig: Extend the dependency for MXS_DMA
dmaengine: mxs: Use %zu for printing a size_t variable
dmaengine: ste_dma40: Cleanup scatterlist layering violations
dmaengine: imx-dma: cleanup scatterlist layering violations
dmaengine: use proper name for the R-Car SoC
dmaengine: imx-sdma: Fix compilation warning.
dmaengine: imx-sdma: Handle return value of clk_prepare_enable
dmaengine: pl330: Add IOMMU support to slave tranfers
dmaengine: DW DMAC: Handle return value of clk_prepare_enable
dmaengine: pl08x: use GENMASK() to create bitmasks
dmaengine: pl08x: Add support for Faraday Technology FTDMAC020
...
When removing a device with less than 9 IRQs (AMBA_NR_IRQS), we'll get a
big WARN_ON from devres.c because pl330_remove calls devm_free_irqs for
unallocated irqs. Similarly to pl330_probe, check that IRQ number is
present before calling devm_free_irq.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Wire up dma_map_resource() for slave transfers, so that we can let the
PL330 use IOMMU-backed DMA mapping ops on systems with an appropriate
IOMMU and RAM above 4GB, to avoid CPU bounce buffering.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver is now used only on platforms which support device tree, so
it is safe to remove legacy platform data based initialization code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
For plat-samsung:
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The static bug finder EBA (http://www.iagoabal.eu/eba/) reported the
following double-lock bug:
Double lock:
1. spin_lock_irqsave(pch->lock, flags) at pl330_free_chan_resources:2236;
2. call to function `pl330_release_channel' immediately after;
3. call to function `dma_pl330_rqcb' in line 1753;
4. spin_lock_irqsave(pch->lock, flags) at dma_pl330_rqcb:1505.
I have fixed it as suggested by Marek Szyprowski.
First, I have replaced `pch->lock' with `pl330->lock' in functions
`pl330_alloc_chan_resources' and `pl330_free_chan_resources'. This avoids
the double-lock by acquiring a different lock than `dma_pl330_rqcb'.
NOTE that, as a result, `pl330_free_chan_resources' executes
`list_splice_tail_init' on `pch->work_list' under lock `pl330->lock',
whereas in the rest of the code `pch->work_list' is protected by
`pch->lock'. I don't know if this may cause race conditions. Similarly
`pch->cyclic' is written by `pl330_alloc_chan_resources' under
`pl330->lock' but read by `pl330_tx_submit' under `pch->lock'.
Second, I have removed locking from `pl330_request_channel' and
`pl330_release_channel' functions. Function `pl330_request_channel' is
only called from `pl330_alloc_chan_resources', so the lock is already
held. Function `pl330_release_channel' is called from
`pl330_free_chan_resources', which already holds the lock, and from
`pl330_del'. Function `pl330_del' is called in an error path of
`pl330_probe' and at the end of `pl330_remove', but I assume that there
cannot be concurrent accesses to the protected data at those points.
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The PL330 is hard-wired such that instruction fetches on both the
manager and channel threads go out onto the bus with the "privileged"
bit set. This can become troublesome once there is an IOMMU or other
form of memory protection downstream, since those will typically be
programmed by the DMA mapping subsystem in the expectation of normal
unprivileged transactions (such as the PL330 channel threads' own data
accesses as currently configured by this driver).
To avoid the case of, say, an IOMMU blocking an unexpected privileged
transaction with a permission fault, use the newly-introduced
DMA_ATTR_PRIVILEGED attribute for the mapping of our microcode buffer.
That way the DMA layer can do whatever it needs to do to make things
continue to work as expected on more complex systems.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mitchel Humpherys <mitchelh@codeaurora.org>
[rm: remove now-redundant local variable, clarify commit message]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
PL330 DMA engine driver is leaking a runtime reference after any terminated
DMA transactions. This patch fixes this issue by tracking runtime PM state
of the device and making additional call to pm_runtime_put() in terminate_all
callback if needed.
Fixes: ae43b32891 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In pl330_add(), variable ‘regs’ is initialized but never used, which
leads to warning with W=1.
drivers/dma/pl330.c: In function 'pl330_add':
drivers/dma/pl330.c:1891:16: warning: variable 'regs' set but not used [-Wunused-but-set-variable]
So remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After executing DMAGO it's possible that a request can come in for the
current xferred count, but if that happens too soon then DMAMOV SAR/DAR
may not have yet completed. If that happens, we should explicitly return 0
since nothing has been transferred yet.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is a racing when accessing dmac thread in pl330_tx_status that
the pl330_update is handling active request at the same time and
changing the status of descriptors. This could cause an invalid
transferred count from BUSY descriptor added up to the residual number.
Fix the bug by using the dmac's spinlock in pl330_tx_status to protect
thread resources from changing.
Note that the nested order of holding dmac's and dma_chan's spinlock is
consistent with the rest of the driver: dma_chan first and then dmac,
so it is safe from deadlock scenario.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Only one descriptor in the work list should be running at
any given time, but it's possible to have an enqueued BUSY
descriptor that has not yet transferred any data, or for
a BUSY descriptor to linger briefly before transitioning
to DONE. These cases should be handled to keep residual
calculations consistent even with the non-running BUSY
descriptors in the work list.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is in preperation of moving to a callback that provides results to the
callback for the transaction. The conversion will maintain current behavior
and the driver must convert to new callback mechanism at a later time in
order to receive results.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine device should explicitly call devm_free_irq() when using
devm_request_irq().
The irq is still ON when devices remove is executed and irq should be
quiesced before remove is completed.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
If kzalloc() fails it will issue it's own error message including
a dump_stack(). So remove the site specific error messages.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the burst mode that will break DMA uart on SoCFPGA.
In some cases, some SoCS didn't support the multi-burst
even if the devices who use the pl330 claim support the maxburst.
Fixes: commit 848e977
"dmaengine: pl330: support burst mode for dev-to-mem and mem-to-dev transmit"
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add max burst capability for dmaengine and
limit burst capability to one for PL330_QUIRK_BROKEN_NO_FLUSHP
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add "arm,pl330-broken-no-flushp" quirk to avoid execute
DMAFLUSHP if Soc doesn't support it.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
cc: Doug Anderson <dianders@chromium.org>
cc: Heiko Stuebner <heiko@sntech.de>
cc: Olof Johansson <olof@lixom.net>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds to support burst mode for dev-to-mem and
mem-to-dev transmit.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
cc: Heiko Stuebner <heiko@sntech.de>
cc: Doug Anderson <dianders@chromium.org>
cc: Olof Johansson <olof@lixom.net>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time we have aded a new capability for scatter-gathered memset using
dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Others
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2 which is
deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gQZ6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have aded a new capability for scatter-gathered memset
using dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Other:
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2
which is deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers"
[ The Kconfig and Makefile entries got re-sorted alphabetically, and I
handled the conflict with the new Intel integrated IDMA driver by
slightly mis-sorting it on purpose: "IDMA64" got sorted after "IMX" in
order to keep the Intel entries together. I think it might be a good
idea to just rename the IDMA64 config entry to INTEL_IDMA64 to make
the sorting be a true sort, not this mismash.
Also, this merge disables the COMPILE_TEST for the sun4i DMA
controller, because it does not compile cleanly at all. - Linus ]
* tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (89 commits)
dmaengine: ioatdma: add Broadwell EP ioatdma PCI dev IDs
dmaengine :ipu: change ipu_irq_handler() to remove compile warning
dmaengine: ioatdma: Fix variable array length
dmaengine: ioatdma: fix sparse "error" with prep lock
dmaengine: hdmac: Add memset capabilities
dmaengine: sort the sh Makefile
dmaengine: sort the sh Kconfig
dmaengine: sort the dw Kconfig
dmaengine: sort the Kconfig
dmaengine: sort the makefile
drivers/dma: make mv_xor.c driver explicitly non-modular
dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller
devicetree: Add bindings documentation for Analog Devices AXI-DMAC
dmaengine: xgene-dma: Fix the lock to allow client for further submission of requests
dmaengine: ioatdma: fix coccinelle warning
dmaengine: ioatdma: fix zero day warning on incompatible pointer type
dmaengine: tegra-apb: Simplify locking for device using global pause
dmaengine: tegra-apb: Remove unnecessary return statements and variables
dmaengine: tegra-apb: Avoid unnecessary channel base address calculation
dmaengine: tegra-apb: Remove unused variables
...
When there is only one burst required do not emit loop instructions to
loop exactly once. Emit just the body of the loop.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When pl330 driver was used during sound playback, after some time or
after a number of plays the sound became choppy or totally noisy. For
example on Odroid XU3 board the first four executions of aplay with
small WAVE worked fine, but fifth was unrecognizable with errors:
$ aplay /usr/share/sounds/alsa/Front_Right.wava
underrun!!! (at least 0.095 ms long)
Issue was caused by wrong residue reported by pl330 driver to
pcm_dmaengine for its cyclic dma transfers.
The pl330_tx_status(), residue reporting function, used a "last" flag in
a descriptor to indicate that there is no more data to send.
The pl330_tx_submit() iterated over descriptors trying to remove this
flag from them and then mark last descriptor as "last". However when
iterating it actually removed the flag not from descriptors but always
from last of it (and then reset it). Thus effectively once some
descriptor was marked as last, then it stayed like this forever causing
residue to be reported too low.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Fixes: aee4d1fac8 ("dmaengine: pl330: improve pl330_tx_status() function")
Cc: <stable@vger.kernel.org>
Reported-by: gabriel@unseen.is
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During memcpy operations the residue was always set to an u32 overflowed
value.
In pl330_tx_status() function number of currently transferred bytes was
subtracted from internal "bytes_requested" field. However this
"bytes_requested" was not initialized at start to length of memcpy
buffer so transferred bytes were subtracted from 0 causing overflow.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: aee4d1fac8 ("dmaengine: pl330: improve pl330_tx_status() function")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time we have support for few new devices, few new features and odd
fixes spread thru the subsystem.
New devices added
- support for CSRatlas7 dma controller
- Allwinner H3(sun8i) controller
- TI DMA crossbar driver on DRA7x
- new pxa driver
New features added:
- memset support is bought back now that we have a user in xdmac controller
- interleaved transfers support different source and destination strides
- supporting DMA routers and configuration thru DT
- support for reusing descriptors
- xdmac memset and interleaved transfer support
- hdmac support for interleaved transfers
- omap-dma support for memcpy
Others
- Constify platform_device_id
- mv_xor fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VM4w
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have support for few new devices, few new features and
odd fixes spread thru the subsystem.
New devices added:
- support for CSRatlas7 dma controller
- Allwinner H3(sun8i) controller
- TI DMA crossbar driver on DRA7x
- new pxa driver
New features added:
- memset support is bought back now that we have a user in xdmac controller
- interleaved transfers support different source and destination strides
- supporting DMA routers and configuration thru DT
- support for reusing descriptors
- xdmac memset and interleaved transfer support
- hdmac support for interleaved transfers
- omap-dma support for memcpy
Others:
- Constify platform_device_id
- mv_xor fixes and improvements"
* tag 'dmaengine-4.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: xgene: fix file permission
dmaengine: fsl-edma: clear pending interrupts on initialization
dmaengine: xdmac: Add memset support
Documentation: dmaengine: document DMA_CTRL_ACK
dmaengine: virt-dma: don't always free descriptor upon completion
dmaengine: Revert "drivers/dma: remove unused support for MEMSET operations"
dmaengine: hdmac: Implement interleaved transfers
dmaengine: Move icg helpers to global header
dmaengine: mv_xor: improve descriptors list handling and reduce locking
dmaengine: mv_xor: Enlarge descriptor pool size
dmaengine: mv_xor: add support for a38x command in descriptor mode
dmaengine: mv_xor: Rename function for consistent naming
dmaengine: mv_xor: bug fix for racing condition in descriptors cleanup
dmaengine: pl330: fix wording in mcbufsz message
dmaengine: sirf: add CSRatlas7 SoC support
dmaengine: xgene-dma: Fix "incorrect type in assignement" warnings
dmaengine: fix kernel-doc documentation
dmaengine: pxa_dma: add support for legacy transition
dmaengine: pxa_dma: add debug information
dmaengine: pxa: add pxa dmaengine driver
...
The kernel is not trying to increase mcbufsz. It suggests you should try
doing so. Also print the calculated required size of mcbufsz.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently pch pointer is already dereferenced before NULL check
and thus we are getting below warning:
warn: variable dereferenced before check 'pch'
So initialize struct pl330_dmac *pl330 after NULL check
of dma_pl330_chan *pch.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330 device could hang infinitely on certain boards when DMA
channels are terminated.
It was caused by lack of runtime resume when executing
pl330_terminate_all() which calls the _stop() function. _stop() accesses
device register and can loop infinitely while checking for device state.
The hang was confirmed by Dinh Nguyen on Altera SOCFPGA Cyclone V
board during boot. It can be also triggered with:
$ echo 1 > /sys/module/dmatest/parameters/iterations
$ echo dma1chan0 > /sys/module/dmatest/parameters/channel
$ echo 1 > /sys/module/dmatest/parameters/run
$ sleep 1
$ cat /sys/module/dmatest/parameters/run
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: ae43b32891 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12")
Cc: <stable@vger.kernel.org>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330_tx_status() function returns the desc->status if the
dma_cookie_status() call does indicate the cookie completed,
however the desc->status is not look directly compatible. Sparse
throws the following warning:
pl330.c:2262:35: warning: mixing different enum types
pl330.c:2262:35: int enum desc_status versus
pl330.c:2262:35: int enum dma_status
Attempt to fix this by adding a switch statement to turn the
desc->status into a dma_status.
Note, this has only been tested with the dmatest suite.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
--
Vinod Koul <vinod.koul@intel.com>
Dan Williams <dan.j.williams@intel.com>
DMA List <dmaengine@vger.kernel.org>
Maxime Ripard <maxime.ripard@free-electrons.com>
Jassi Brar <jassisinghbrar@gmail.com>
Liviu Dudau <Liviu.Dudau@arm.com>
Linux ARM Kernel <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Whilst running sparse on pl330 driver it was noticed there are
two functions that are not static but not exported to any other
users in the kernel.
Fix the following warnings by making 'pl330_pause' and the
'pl330_get_current_xferred_count' static:
pl330.c:2165:5: warning: symbol 'pl330_pause' was not declared. Should it be static?
pl330.c:2206:5: warning: symbol 'pl330_get_current_xferred_count' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
--
Vinod Koul <vinod.koul@intel.com>
Dan Williams <dan.j.williams@intel.com>
DMA List <dmaengine@vger.kernel.org>
Maxime Ripard <maxime.ripard@free-electrons.com>
Jassi Brar <jassisinghbrar@gmail.com>
Liviu Dudau <Liviu.Dudau@arm.com>
Linux ARM Kernel <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When running Xilinx Zynq in big-endian mode the pl330 driver
fails to pass the dmatest suite. To fix this, ensure all non
byte values are written in little endian.
As a note, the documentation does not mention if it will do
big-endian descriptor fetches, only that it will swap the
data in flight.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
--
Vinod Koul <vinod.koul@intel.com>
Dan Williams <dan.j.williams@intel.com>
DMA List <dmaengine@vger.kernel.org>
Maxime Ripard <maxime.ripard@free-electrons.com>
Jassi Brar <jassisinghbrar@gmail.com>
Liviu Dudau <Liviu.Dudau@arm.com>
Linux ARM Kernel <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DMA_PAUSE command is used for halting DMA transfer on chosen channel.
It can be useful when we want to safely read residue before terminating
all requests on channel. Otherwise there can be situation when some data
is transferred before channel termination but after reading residue,
which obviously results with data loss. To avoid this situation we can
pause channel, read residue and then terminate all requests.
This scenario is common, for example, in serial port drivers.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds possibility to read residue of DMA transfer. It's useful
when we want to know how many bytes have been transferred before we
terminate channel. It can take place, for example, on timeout interrupt.
Signed-off-by: Lukasz Czerwinski <l.czerwinski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the AMBA PL330 DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dmaengine header abbreviates destination as at least two different strings.
Make a coherent use of a single one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull ARM updates from Russell King:
"The major updates included in this update are:
- Clang compatible stack pointer accesses by Behan Webster.
- SA11x0 updates from Dmitry Eremin-Solenikov.
- kgdb handling of breakpoints with read-only text/modules
- Support for Privileged-no-execute feature on ARMv7 to prevent
userspace code execution by the kernel.
- AMBA primecell bus handling of irq-safe runtime PM
- Unwinding support for memset/memzero/memmove/memcpy functions
- VFP fixes for Krait CPUs and improvements in detecting the VFP
architecture
- A number of code cleanups (using pr_*, removing or reducing the
severity of a couple of kernel messages, splitting ftrace asm code
out to a separate file, etc.)
- Add machine name to stack dump output"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (62 commits)
ARM: 8247/2: pcmcia: sa1100: make use of device clock
ARM: 8246/2: pcmcia: sa1111: provide device clock
ARM: 8245/1: pcmcia: soc-common: enable/disable socket clocks
ARM: 8244/1: fbdev: sa1100fb: make use of device clock
ARM: 8243/1: sa1100: add a clock alias for sa1111 pcmcia device
ARM: 8242/1: sa1100: add cpu clock
ARM: 8221/1: PJ4: allow building in Thumb-2 mode
ARM: 8234/1: sa1100: reorder IRQ handling code
ARM: 8233/1: sa1100: switch to hwirq usage
ARM: 8232/1: sa1100: merge GPIO multiplexer IRQ to "normal" irq domain
ARM: 8231/1: sa1100: introduce irqdomains support
ARM: 8230/1: sa1100: shift IRQs by one
ARM: 8229/1: sa1100: replace irq numbers with names in irq driver
ARM: 8228/1: sa1100: drop entry-macro.S
ARM: 8227/1: sa1100: switch to MULTI_IRQ_HANDLER
ARM: 8241/1: Update processor_modes for hyp and monitor mode
ARM: 8240/1: MCPM: document mcpm_sync_init()
ARM: 8239/1: Introduce {set,clear}_pte_bit
ARM: 8238/1: mm: Refine set_memory_* functions
ARM: 8237/1: fix flush_pfn_alias
...
Pull dmaengine updates from Vinod Koul:
"Main features this time are:
- BAM v1.3.0 support form qcom bam dma
- support for Allwinner sun8i dma
- atmels eXtended DMA Controller driver
- chancnt cleanup by Maxime
- fixes spread over drivers"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (56 commits)
dmaenegine: Delete a check before free_percpu()
dmaengine: ioatdma: fix dma mapping errors
dma: cppi41: add a delay while setting the TD bit
dma: cppi41: wait longer for the HW to return the descriptor
dmaengine: fsl-edma: fixup reg offset and hw S/G support in big-endian model
dmaengine: fsl-edma: fix calculation of remaining bytes
drivers/dma/pch_dma: declare pch_dma_id_table as static
dmaengine: ste_dma40: fix error return code
dma: imx-sdma: clarify about firmware not found error
Documentation: devicetree: Fix Xilinx VDMA specification
dmaengine: pl330: update author info
dmaengine: clarify the issue_pending expectations
dmaengine: at_xdmac: Add DMA_PRIVATE
ARM: dts: at_xdmac: fix bad value of dma-cells in documentation
dmaengine: at_xdmac: fix missing spin_unlock
dmaengine: at_xdmac: fix a bug in transfer residue computation
dmaengine: at_xdmac: fix software lockup at_xdmac_tx_status()
dmaengine: at_xdmac: remove chancnt affectation
dmaengine: at_xdmac: prefer usage of readl/writel_relaxed
dmaengine: xdmac: fix print warning on dma_addr_t variable
...
Update email-id to a personal one, as I have changed employment.
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add system suspend/resume capabilities to the pl330 driver so the amba
bus clock could be also unprepared to conserve energy.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds runtime PM support to pl330 DMA engine driver.
The runtime power management for pl330 DMA driver allows gating of AMBA
clock (PDMA) in FSYS clock domain, when the device is not processing any
requests. This is necessary to enter low power modes on Exynos SoCs
(e.g. LPA on Exynos4x12 or W-AFTR on Exynos3250).
Runtime PM resuming of the device may happen in atomic context (during
call device_issue_pending()) so pm_runtime_irq_safe() is used. This will
lead only to disabling/enabling of the clock but this is sufficient for
gating the clock and for reducing energy usage.
Driver uses runtime PM callbacks from amba/bus.c driver only.
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
