When the video timings are suitably aligned so that all different
periods start at phase 0 (ie. none of the periods start mid-pixel)
we can inform the sink about this. Supposedly the sink can then
optimize certain things. Obviously this is only relevant when
outputting >8bpc data since otherwise there are no mid-pixel phases.
v2: Rebased due to crtc->config changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GCP infoframes are required to inform the HDMI sink about the color
depth.
Send the GCP infoframe whenever the sink supports any deep color modes
since such sinks must anyway be capable of receiving them. For sinks
that don't support deep color let's skip the GCP in case it might
confuse the sink, although HDMI 1.4 spec does say all sinks must be
capable of reciving them. In theory we could skip the GCP infoframe
for deep color sinks in 8bpc mode as well since sinks must fall back to
8bpc whenever GCP isn't received for some time.
BSpec says we should disable GCP after disabling the port, so do that as
well.
v2: s/intel_set_gcp_infoframe/intel_hdmi_set_gcp_infoframe/
Rebased due to crtc->config changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict with lack of chv phy patches and fixup typo
Chandra spotted.]
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we can have requests even if though the active list is empty,
so do the request retirement regardless of whether there's anything
on the active list.
The way it happened here is that during suspend intel_ring_idle()
notices the olr hanging around and then proceeds to get rid of it by
adding a request. However since there was nothing on the active lists
i915_gem_retire_requests() didn't clean those up, and so the idle work
never runs, and we leave the GPU "busy" during suspend resulting in a
WARN later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
CPT/PPT require a specific procedure for enabling 12bpc HDMI. Implement
it, and to keep things neat pull the code into a function.
v2: Rebased due to crtc->config changes
s/HDMI_GC/HDMIUNIT_GC/ to match spec better
Factor out intel_enable_hdmi_audio()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-By: Chandra Konduru <Chandra.konduru@intel.com>
Testecase: igt/kms_render/*
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix warnings related to size_t when building for 64-bit architectures:
drivers/gpu/drm/drm_gem_cma_helper.c: In function ‘drm_gem_cma_create’:
drivers/gpu/drm/drm_gem_cma_helper.c:114:4: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t’ [-Wformat=]
size);
^
drivers/gpu/drm/drm_gem_cma_helper.c: In function ‘drm_gem_cma_describe’:
drivers/gpu/drm/drm_gem_cma_helper.c:393:4: warning: format ‘%d’ expects argument of type ‘int’, but argument 8 has type ‘size_t’ [-Wformat=]
off, &cma_obj->paddr, cma_obj->vaddr, obj->size);
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rework the crtc event/flip_wait system as follows:
- If we enable a crtc (full modeset), we set omap_crtc->pending and
register vblank irq.
- If we need to set GO bit (page flip), we do the same but also set the
GO bit.
- On vblank we unregister the irq, clear the 'pending' flag, send vblank
event to userspace if crtc->state->event != NULL, and wake up
'pending_wait' wq.
- In omap_atomic_complete() we wait for the 'pending' flag to get reset
for all enabled crtcs using 'pending_wait' wq.
The above ensures that we send the events to userspace in vblank, and
that after the wait in omap_atomic_complete() everything for the
affected crtcs has been completed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_crtc_atomic_flush() is the only user of omap_crtc_flush(), so just
move the code from omap_crtc_flush() to omap_crtc_atomic_flush().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Before atomic modesetting omap_framebuffer_pin() and
omap_framebuffer_unpin() were always called with modesetting locks
taken. With atomic modesetting support this is no longer the case, and
we need locking to protect the pin_count and the paddr, as multiple
threads may pin the same fb concurrently.
This patch adds a mutex to struct omap_framebuffer, and uses it in
omap_framebuffer_pin() and omap_framebuffer_unpin().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_plane_atomic_update() calls dispc_ovl_setup(), which can fail (but
shouldn't). To make the code a bit more robust, make sure the plane gets
disabled if dispc_ovl_setup() fails, as otherwise we might get illegal
HW configuration leading to error interrupts.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
At the moment we have omap_plane_setup() function which handles both
enabling (and configuring) and disabling the plane. With atomic
modesetting we have separate hooks for plane enable/config and disable.
This patch moves the code from omap_plane_setup() to
omap_plane_atomic_update() and omap_plane_atomic_disable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
With atomic modesetting, omap_plane_setup()'s return value is ignored as
the functions using it cannot fail. dispc_ovl_setup(), called by
omap_plane_setup(), can fail (but shouldn't).
Instead of returning an error from omap_plane_setup() which gets
ignored, return void and use WARN if dispc_ovl_setup() fails.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Planes setup is handled by the DRM core through the atomic helpers,
there's no need to duplicate the code in the CRTC .enable() and
.disable() operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_crtc_flush() call in omap_crtc_enable() and omap_crtc_disable()
is a no-op, as the display manager is always disabled at this point. Just
remove the function call.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the driver is fully converted to atomic operations, and that
the atomic helpers call the operations in the right order, we can move
encoder setup to where it belongs, in the encoder operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of sprinkling dispc_runtime_get() and dispc_runtime_put() calls
in various CRTC operations, move all power management code to the atomic
commit function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_crtc_encoder_setup() function is always called with the DSS
enabled. Remove the dispc_runtime_get() and dispc_runtime_put() calls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DRM page flip vblank events requested by page flips or atomic commits
are created by the DRM core and then passed to driver through CRTC
states (for atomic commit) or directly to the page flip handler (for
legacy page flips). The events are then kept aside until the page flip
completes, at which point drivers queue them for delivery with a call to
drm_send_vblank_event().
When a DRM file handle is closed events pending for delivery are cleaned
up automatically by the DRM core. Events that have been passed to the
driver but haven't completed yet, however, are not handled by the DRM
core. Drivers are responsible for destroying them and must not attempt
to queue them for delivery. This is usually handled by drivers'
preclose() handlers that cancel and destroy page flip events that
reference the file handle being closed.
With asynchronous atomic updates the story becomes more complex. Several
asynchronous atomic updates can be pending, each of them carrying
per-CRTC events. As the atomic_commit() operation doesn't receive a file
handle context, drivers can't know which file handle a pending update
refers to, making it difficult to cancel or wait for completion of
updates related to the file handle being closed.
It should be noted that cancelling page flips or waiting for atomic
updates completion isn't required by the DRM core when closing a file
handle. The only requirement is that no event gets queued for delivery
after the preclose() operation returns. This can easily be achieved by
storing events for atomic commits in a list, unlinking events from the
file handle being closed by setting the file_priv field to NULL, and
skipping delivery of unlinked events.
This logic replaces the page flip cancellation completely.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When performing asynchronous atomic updates the modeset lock isn't taken
around the callers of omap_crtc_flush(). This isn't an issue though, as
access to the CRTC is properly serialized. Just drop the warning.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_crtc_flush() function is always called with a reference to the
dispc held. Remove unnecessary calls to dispc_runtime_get() and
dispc_runtime_put().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function isn't used outside of its compilation unit, make it static.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The field tracks the plane state to avoid double-enable or -disable.
This isn't required anymore, as
- the DRM atomic core guarantees that the plane atomic_update and
atomic_disable functions will never be called on an enabled/disabled
plane
- the CRTC enable/disable operations that enable/disable the plane are
already guarded against double enable/disable
We can thus remove the enabled field completely. The
omap_plane_set_enable() function then becomes a wrapper around
omap_plane_setup() which can be called directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The field tracks the CRTC state to avoid double-enable or -disable. As
the DRM atomic core guarantees that the CRTC enable and disable
functions won't be called on an already enabled or disabled CRTC, such
tracking isn't needed. Remove the enabled field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The crtc info structure is only used to setup the crtc through the DSS
API. Move it from the crtc structure to local variables in
omap_crtc_dss_enable().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The plane info and win structures are only used to setup the plane
through the DSS API. Move them from the plane structure to local
variables in omap_plane_setup().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Allow setting up plane properties atomically using the plane
set_property atomic helper. The properties are now stored in the plane
state (requiring subclassing it) and applied when updating the planes.
The CRTC exposes the properties of its primary plane for legacy reason.
We can't get rid of that API, so simply delegate it to the primary
plane.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since the removal of omap_plane_mode_set(), framebuffers are now pinned
exclusively through the plane .prepare_fb() and .cleanup_fb() operations
as the remaining callers of omap_plane_setup() don't modify the
framebuffer. Remove the manual pin/unpin infrastructure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The atomic page flip helper implements the page flip operation using
asynchronous commits.
As the legacy page flip was the last caller of omap_plane_mode_set(),
remove the function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implement a custom .atomic_commit() handler that supports asynchronous
commits using a work queue. This can be used for userspace-driven
asynchronous commits, as well as for an atomic page flip implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The encoder .mode_fixup() operation is legacy, atomic updates uses the
new .atomic_check() operation. Convert the encoder driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The atomic connector DPMS helper implements the connector DPMS operation
using atomic commit, removing the need for DPMS helper operations on
CRTCs and encoders.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This removes the legacy mode config code. The CRTC and encoder prepare
and commit operations are not used anymore, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This removes the legacy plane update code. Wire up the default atomic
check and atomic commit mode config helpers as needed by the plane
update atomic helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the new CRTC atomic transitional helpers drm_helper_crtc_mode_set()
and drm_helper_crtc_mode_set_base() to implement the CRTC .mode_set and
.mode_set_base operations. This delegates primary plane configuration to
the plane .atomic_update and .atomic_disable operations, removing
duplicate code from the CRTC implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implement the CRTC .atomic_begin() and .atomic_flush() operations, the
plane .atomic_check(), .atomic_update() and operations, and use the
transitional atomic helpers to implement the plane update and disable
operations on top of the new atomic operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hook up the default .reset(), .atomic_duplicate_state() and
.atomic_free_state() helpers to ensure that state objects are properly
created and destroyed, and call drm_mode_config_reset() at init time to
create the initial state objects.
Framebuffer reference count also gets maintained automatically by the
transitional helpers except for the legacy page flip operation. Maintain
it explicitly there.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The operations are required by the atomic helpers, implement them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When using atomic updates the CRTC .enable() and .disable() helper
operations are preferred over the (then legacy) .prepare() and .commit()
operations. Implement .enable() and rework .disable() to not depend on
DPMS, easing DPMS removal later on.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_crtc_enable() and omap_crtc_disable() DSS operations functions
will clash with the new CRTC enable and disable helpers. Rename them to
omap_crtc_dss_*, as well as the other DSS operations for consistency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the <...> include style instead of "..." for DRM headers and sort
the headers alphabetically to ease detection of duplicates.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can't rely on crtc->primary->fb in the page flip worker, as a racing
CRTC disable (due for instance to an explicit framebuffer deletion from
userspace) would set that field to NULL before the worker gets a change
to run. Store the framebuffer queued for page flip in a new field of
omap_crtc instead, and hold a reference to it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DRM core vblank handling mechanism requires drivers to forcefully
turn vblank reporting off when disabling the CRTC, and to restore the
vblank reporting status when enabling the CRTC.
Implement this using the drm_crtc_vblank_on/off helpers. When disabling
vblank we must first wait for page flips to complete, so implement page
flip completion wait as well.
Finally, drm_crtc_vblank_off() must be called at startup to synchronize
the state of the vblank core code with the hardware, which is initially
disabled. An interesting side effect is that the .disable_vblank()
operation will now be called for the first time with the CRTC disabled
and the DISPC runtime suspended. The dispc_runtime_get() call in
.disable_vblank() is supposed to take care of that, but the operation is
called with a spinlock held, which prevents it from sleeping.
To fix that move DISPC runtime PM handling out of the vblank operations
to the CRTC code, ensuring that the display controller will always be
powered when enabling or disabling vblank interrupts.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To implement proper vblank control the driver will need to wait for page
flip completion before disabling the vblank interrupt. This is made
complex by the page flip implementation which queues and submits page
flips to the hardware in two separate steps between which DRM locks are
released. We thus need to avoid waiting on a page flip that has been
queued but not submitted as submission and wait are covered by the same
lock.
Rework page flip handling as a first step by splitting the flip_pending
boolean variable into an enumerated state and moving between states
based on flip queue, submission and completion. The CANCELLED state will
be used in a second step.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pending page flips must be cancelled when closing the device, otherwise
their completion at next vblank will result in nasty effects, including
possible oopses due to resources required to complete the page flip
being freed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm can't use drm_irq_install() and drm_irq_uninstall() as it
delegates IRQ handling to the omapdss driver. However, the code still
declares IRQ-related operations used by the DRM IRQ helpers, and calls
them indirectly.
Simplify the implementation by calling the functions directly or
inlining them. The irq_enabled checks can then also be simplified as
the call stacks guarantees that omap_drm_irq_install() and
omap_drm_irq_uninstall() will never run concurrently.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The old_fb field is only used to indicate whether a page flip is
pending. Turn it into a bool named flip_pending. Rename event and
page_flip_work to flip_event and flip_work for consistency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The operation is called page_flip, rename its implementation
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm driver implements a mechanism to apply new settings (due to
plane update, plane disable, plane property set, CRTC mode set or CRTC
DPMS) asynchronously. While this improves performance, it adds a level
of complexity that makes transition to the atomic update API close to
impossible. Furthermore the atomic update API requires part of the apply
operations to be synchronous (such as pinning the framebuffers), so the
current implementation needs to be changed.
Simplify the CRTC and plane code by making updates synchronous to
prepare for the switch to the atomic update API. Asynchronous update
will be implemented in a second step.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rotation is a standard property, store it in
dev->mode_config.rotation_property. While at it, extract the properties
initialization code to a separate function instead of running it for
every plane.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds the bus_format field to the HSD100PXN1 panel structure.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Hannstar HSD100PXN1 to the DRM simple panel driver.
The HSD100PXN1 is an XGA (1024x768) panel with an 18-bit LVDS interface.
It supports pixel clocks in the range of 55-75 MHz.
This panel is offered for sale by Freescale as a companion part to its'
i.MX5x Quick Start board and i.MX6 SABRE platforms with under the name
MCIMX-LVDS1.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The DPAUX registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pages allocated from shmemfs don't end up being cleared and flushed on
ARMv7, so they must be flushed explicitly. Use the DMA mapping API for
that purpose, even though it's not used for anything else.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The IOMMU may not always be able to address 2 GiB of memory. On Tegra20,
the GART supports 32 MiB starting at 0x58000000. Also the aperture on
Tegra30 and later is in fact the full 4 GiB, rather than just 2 GiB as
currently assumed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX read/write FIFO registers aren't sequential in the register
space, causing transfers larger than 4 bytes to cause accesses to non-
existing FIFO registers.
Fixes: 6b6b604215 ("drm/tegra: Add eDP support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
This was introduced after converting hw readout to atomic,
so it should have been part of the revert too.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90929
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use a full atomic call instead. intel_crtc_page_flip will still
have to live until async updates are allowed.
This doesn't seem to be a regression from the convert to atomic,
part 3 patch. During GPU reset it fixes the following warning:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 752 at drivers/gpu/drm/drm_crtc.c:5337 drm_mode_page_flip_ioctl+0x27b/0x360()
Modules linked in: i915
CPU: 0 PID: 752 Comm: Xorg Not tainted 4.1.0-rc7-patser+ #4090
Hardware name: NUC5i7RYB, BIOS RYBDWi35.86A.0246.2015.0309.1355 03/09/2015
ffffffff81c90866 ffff8800d87c3ca8 ffffffff817f7d87 0000000080000001
0000000000000000 ffff8800d87c3ce8 ffffffff81084955 ffff880000000000
ffff8800d87c3dc0 ffff8800d93d1208 0000000000000000 ffff8800b7d1f3e0
Call Trace:
[<ffffffff817f7d87>] dump_stack+0x4f/0x7b
[<ffffffff81084955>] warn_slowpath_common+0x85/0xc0
[<ffffffff81084a35>] warn_slowpath_null+0x15/0x20
[<ffffffff8146dffb>] drm_mode_page_flip_ioctl+0x27b/0x360
[<ffffffff8145ccb0>] drm_ioctl+0x1a0/0x6a0
[<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[<ffffffff812e5540>] ? avc_has_perm+0x20/0x280
[<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[<ffffffff811ea0f8>] do_vfs_ioctl+0x2f8/0x530
[<ffffffff811f6001>] ? expand_files+0x261/0x270
[<ffffffff812e7c16>] ? selinux_file_ioctl+0x56/0x100
[<ffffffff811ea3b1>] SyS_ioctl+0x81/0xa0
[<ffffffff81801b97>] system_call_fastpath+0x12/0x6f
---[ end trace 9ce834560085bd64 ]---
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This should fix fallout caused by making intel_crtc_control
and update_dpms atomic, which became a problem after reverting the
atomic hw readout patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90929
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 3bae26eb2991c00670df377cf6c3bc2b0577e82a.
Seems it introduces regressions for 3 different reasons, oh boy..
In bug #90868 as I can see the atomic state will be restored on
resume without the planes being set up properly. Because plane
setup here requires the atomic state, we'll have to settle
for committing atomic planes first.
In bug #90861 the failure appears to affect mostly DP devices,
and happens because reading out the atomic state prevents a modeset
on boot, which would require better hw state readout.
In bug #90874 it's shown that cdclk should be part of the atomic
state, so only performing a single modeset during resume excarbated
the issue.
It's better to fix those issues first, and then commit this patch,
so do that temporarily.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 490f400db5d886fc28566af69b02f6497f31be4b.
We're not ready yet to make it atomic, we calculate some state in
advance, but without atomic plane support atomic the hw readout will
fail.
It's required to revert this commit to revert the atomic hw
state readout patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
crtc->active will be gone eventually, and this check should be just as good.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a small behavioral change because it leaves DVO_2X_MODE
set between crtc_disable and crtc_enable. This is probably harmless
though and if not should be fixed by calculating 2x mode before
enable/disable pll.
This is needed because intel_crtc->active will be removed eventually.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This needs to be done last after all modesets have been calculated.
A modeset first disables all crtc's, so any crtc that undergoes a
modeset counts as inactive.
If no modeset's done, or > 1 crtc's stay w/a doesn't apply.
Apply workaround on the first crtc if 1 crtc stays active.
Apply workaround on the second crtc if no crtc was active.
Changes since v1:
- Use intel_crtc->atomic as a place to put hsw_workaround_pipe.
- Make sure quirk only applies to haswell.
- Use first loop to iterate over newly enabled crtc's only.
This increases readability.
Changes since v2:
- Move hsw_workaround_pipe back to crtc_state.
Changes since v3:
- Return errors from haswell_mode_set_planes_workaround.
Changes since v4:
- Clean up commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
crtc->config is updated to always contain to the active crtc_state
and only differs from crtc_state during crtc_disable. It will
eventually be removed, so start with some low hanging fruit.
For crtc->active the situation is the same; it will be removed
eventually. Instead use crtc->state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
intel_crtc->config will be removed eventually, so use crtc->hwmode.
drm_atomic_helper_update_legacy_modeset_state updates hwmode,
but crtc->active will eventually be gone too. Set dotclock to zero
to indicate the crtc is inactive.
Changes since v1:
- With the hwmode update in drm*update_legacy_modeset_state removed,
intel_modeset_update_state has to assign it instead.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a preparation for passing crtc state to the helpers.
When converting all users of crtc->config to use the old or
new state it's easier to find regressions when swap_state is
done first.
If crtc->config is swapped at the same place as swap_state
bugs will never be found.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Calculate all state using a normal transition, but afterwards fudge
crtc->state->active back to its old value. This should still allow
state restore in setup_hw_state to work properly.
Calling intel_set_mode will cause intel_display_set_init_power to be
called, make sure init_power gets set again afterwards.
Changes since v1:
- Fix to compile with v2 of the patch that adds intel_display_suspend.
- Add intel_display_set_init_power.
- Set return value to int to allow error checking.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Assume the callers lock everything with drm_modeset_lock_all.
This change had to be done after converting suspend/resume to
use atomic_state so the atomic state is preserved, otherwise
all transitional state is erased.
Now all callers of .crtc_enable and .crtc_disable go through
atomic modeset! :-D
Changes since v1:
- Only check for crtc_state->active in valleyview_modeset_global_pipes.
- Only check for crtc_state->active in modeset_update_crtc_power_domains.
Changes since v2:
- Rework on top of the changed patch order.
Changes since v3:
- Rename intel_crtc_toggle in description to *_control
- Change return value to int.
- Do not add plane state, should be done implicitly already.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
To make this work we load the new hardware state into the
atomic_state, then swap it with the sw state.
This lets us change the force restore path in setup_hw_state()
to use a single call to intel_mode_set() to restore all the
previous state.
As a nice bonus this kills off encoder->new_encoder,
connector->new_enabled and crtc->new_enabled. They were used only
to restore the state after a modeset.
Changes since v1:
- Make sure all possible planes are added with their crtc set,
so they will be turned off on first modeset.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
It makes more sense there, since these are computation steps that can
fail.
Changes since v1:
- Rename __intel_set_mode_checks to intel_modeset_checks (Matt Roper)
- Move intel_modeset_checks to before check_planes, so it won't
have to be moved later.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Repeated calls to begin_crtc_commit can cause warnings like this:
[ 169.127746] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616
[ 169.127835] in_atomic(): 0, irqs_disabled(): 1, pid: 1947, name: kms_flip
[ 169.127840] 3 locks held by kms_flip/1947:
[ 169.127843] #0: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffff814774bc>] __drm_modeset_lock_all+0x9c/0x130
[ 169.127860] #1: (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffff814774cd>] __drm_modeset_lock_all+0xad/0x130
[ 169.127870] #2: (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffff81477178>] drm_modeset_lock+0x38/0x110
[ 169.127879] irq event stamp: 665690
[ 169.127882] hardirqs last enabled at (665689): [<ffffffff817ffdb5>] _raw_spin_unlock_irqrestore+0x55/0x70
[ 169.127889] hardirqs last disabled at (665690): [<ffffffffc0197a23>] intel_pipe_update_start+0x113/0x5c0 [i915]
[ 169.127936] softirqs last enabled at (665470): [<ffffffff8108a766>] __do_softirq+0x236/0x650
[ 169.127942] softirqs last disabled at (665465): [<ffffffff8108ae75>] irq_exit+0xc5/0xd0
[ 169.127951] CPU: 1 PID: 1947 Comm: kms_flip Not tainted 4.1.0-rc4-patser+ #4039
[ 169.127954] Hardware name: LENOVO 2349AV8/2349AV8, BIOS G1ETA5WW (2.65 ) 04/15/2014
[ 169.127957] ffff8800c49036f0 ffff8800cde5fa28 ffffffff817f6907 0000000080000001
[ 169.127964] 0000000000000000 ffff8800cde5fa58 ffffffff810aebed 0000000000000046
[ 169.127970] ffffffff81c5d518 0000000000000268 0000000000000000 ffff8800cde5fa88
[ 169.127981] Call Trace:
[ 169.127992] [<ffffffff817f6907>] dump_stack+0x4f/0x7b
[ 169.128001] [<ffffffff810aebed>] ___might_sleep+0x16d/0x270
[ 169.128008] [<ffffffff810aed38>] __might_sleep+0x48/0x90
[ 169.128017] [<ffffffff817fc359>] mutex_lock_nested+0x29/0x410
[ 169.128073] [<ffffffffc01635f0>] ? vgpu_write64+0x220/0x220 [i915]
[ 169.128138] [<ffffffffc017fddf>] ? ironlake_update_primary_plane+0x2ff/0x410 [i915]
[ 169.128198] [<ffffffffc0190e75>] intel_frontbuffer_flush+0x25/0x70 [i915]
[ 169.128253] [<ffffffffc01831ac>] intel_finish_crtc_commit+0x4c/0x180 [i915]
[ 169.128279] [<ffffffffc00784ac>] drm_atomic_helper_commit_planes+0x12c/0x240 [drm_kms_helper]
[ 169.128338] [<ffffffffc0184264>] __intel_set_mode+0x684/0x830 [i915]
[ 169.128378] [<ffffffffc018a84a>] intel_crtc_set_config+0x49a/0x620 [i915]
[ 169.128385] [<ffffffff817fdd39>] ? mutex_unlock+0x9/0x10
[ 169.128391] [<ffffffff81467b69>] drm_mode_set_config_internal+0x69/0x120
[ 169.128398] [<ffffffff8119b547>] ? might_fault+0x57/0xb0
[ 169.128403] [<ffffffff8146bf93>] drm_mode_setcrtc+0x253/0x620
[ 169.128409] [<ffffffff8145c600>] drm_ioctl+0x1a0/0x6a0
[ 169.128415] [<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[ 169.128424] [<ffffffff811e9ab8>] do_vfs_ioctl+0x2f8/0x530
[ 169.128429] [<ffffffff810d0fcd>] ? trace_hardirqs_on+0xd/0x10
[ 169.128435] [<ffffffff812e7676>] ? selinux_file_ioctl+0x56/0x100
[ 169.128439] [<ffffffff811e9d71>] SyS_ioctl+0x81/0xa0
[ 169.128445] [<ffffffff81800697>] system_call_fastpath+0x12/0x6f
Solve it by using the newly introduced drm_atomic_helper_commit_planes_on_crtc.
The problem here was that the drm_atomic_helper_commit_planes() helper
we were using was basically designed to do
begin_crtc_commit(crtc #1)
begin_crtc_commit(crtc #2)
...
commit all planes
finish_crtc_commit(crtc #1)
finish_crtc_commit(crtc #2)
The problem here is that since our hardware relies on vblank evasion,
our CRTC 'begin' function waits until we're out of the danger zone in
which register writes might wind up straddling the vblank, then disables
interrupts; our 'finish' function re-enables interrupts after the
registers have been written. The expectation is that the operations between
'begin' and 'end' must be performed without sleeping (since interrupts
are disabled) and should happen as quickly as possible. By clumping all
of the 'begin' calls together, we introducing a couple problems:
* Subsequent 'begin' invocations might sleep (which is illegal)
* The first 'begin' ensured that we were far enough from the vblank that
we could write our registers safely and ensure they all fell within
the same frame. Adding extra delay waiting for subsequent CRTC's
wasn't accounted for and could put us back into the 'danger zone' for
CRTC #1.
This commit solves the problem by using a new helper that allows an
order of operations like:
for each crtc {
begin_crtc_commit(crtc) // sleep (maybe), then disable interrupts
commit planes for this specific CRTC
end_crtc_commit(crtc) // reenable interrupts
}
so that sleeps will only be performed while interrupts are enabled and
we can be sure that registers for a CRTC will be written immediately
once we know we're in the safe zone.
The crtc->config->base.crtc update may seem unrelated, but the helper
will use it to obtain the crtc for the state. Without the update it
will dereference NULL and crash.
Changes since v1:
- Use Matt Roper's commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
And update crtc->config to point to the new state. There is no point
in swapping only part of the state when the rest of the state
should be untouched.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that we can subclass drm_atomic_state we can also use it to keep
track of all the pll settings. atomic_state is a better place to hold
all shared state than keeping pll->new_config everywhere.
Changes since v1:
- Assert connection_mutex is held.
Changes since v2:
- Fix swapped arguments to kzalloc for intel_atomic_state_alloc. (Jani Nikula)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The primary plane can still be configured when crtc is off,
furthermore this is also a noop now that affected planes are
added on modesets.
Changes since v1:
- Move commit so no frontbuffer_bits warnings are generated.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Compute new pipe_configs for all crtcs in the atomic state. The commit
part of the mode set (__intel_set_mode()) is already enabled to support
multiple pipes, the only thing missing was calculating a new pipe_config
for every crtc.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This should be much cleaner, with the same effects.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This can happen when turning off a sprite plane. Because the crtc state
is not yet always swapped correctly and transitional helpers are used
the crtc state cannot be relied on.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Atomic planes updates rely on having a accurate plane_mask.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add missing calls to drm_atomic_add_affected_*. This is needed
to convert to atomic planes. When converting to atomic all planes
are needed on modeset. For good measure make sure all connectors
are added too.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
crtc_state->enable means a crtc is configured, but it may be turned
off for dpms. Until the commit "use intel_crtc_control everywhere"
crtc_state->active was not updated on crtc off, but now
crtc_state->active should be used for tracking whether a crtc is
scanning out or not.
A few commits from now dpms will be handled by calling
intel_set_mode with a different value for crtc_state->active,
which causes a crtc to turn on or off.
At this point crtc->active should mirror crtc_state->active,
so some paranoia from the crtc_disable functions can be removed.
intel_set_mode_setup_plls still checks for ->enable, because all
resources that are needed have to be calculated, else
dpms changes may not succeed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
A follow up patch will make intel_modeset_compute_config() deal with
multiple crtcs, so move crtc specific stuff into the lower level crtc
specific function.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With the use of drm_atomic_helper_update_legacy_modeset_state the
last user of modeset_crtc is removed from this function.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that the helper is exported there's no need to duplicate
this code any more.
Changes since v1:
- move intel_modeset_update_staged_output_state call to the right place.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Having a single path for everything makes it a lot easier to keep
crtc_state->active in sync with intel_crtc->active.
A crtc cannot be changed to active when not enabled, because it means
no mode is set and no connectors are connected.
This should also make intel_crtc->active match crtc_state->active.
Changes since v1:
- Reworded commit message, there's no intel_crtc_toggle.
Changes since v2:
- Change some callers of intel_crtc_control to intel_display_suspend.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a function used to disable all crtc's. This makes it clearer
to distinguish between when mode needs to be preserved and when
it can be trashed.
Changes since v1:
- Copy power changes from intel_crtc_control.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that the dpll updates are (mostly) atomic, the .off() code is a noop,
and intel_crtc_disable does mostly the same as intel_modeset_update_state.
Move all logic for connectors_active and setting dpms to that function.
Changes since v1:
- Move drm_atomic_helper_swap_state up.
Changes since v2:
- Split out intel_put_shared_dpll removal.
Changes since v3:
- Rebase on top of latest drm-intel.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that the pll updates are staged the put_shared_dpll function
consists only of checks that are done in check_shared_dpll_state
after a modeset too.
The changes to pll->config are overwritten by
intel_shared_dpll_commit, so this entire function is a noop.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
According to bspec the DDI PHY vswing scale value is "don't care" in
case the scale enable bit [27] is clear. But this doesn't seem to be
correct. The scale value seems to also matter if the scale mode bit
[26] is set. So both bit 26 and 27 depend on the value. Setting the
scale value to 0 while either bit is set results in a failed modeset on
HDMI (sink reports no signal).
After reset the scale value is 0x98, but according to the spec we have
to program it to 0x9a. So for consistency program it always to 0x9a
regardless of the scale enable bit.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville's and Mika's cdclk series was in flight at the same time as the
SKL S3 patches so we were missing that update.
intel_update_max_cdclk() and intel_update_cdclk() had to be moved up a
bit to avoid forward declarations.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
intel_update_cdclk() will already display the boot CDCLK for DDI
platforms, no need to repeat there.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We can operate with DPLL0 off with CDCLK backed by the 24Mhz reference
clock, and that's a supported configuration. Don't warn when notice
DPLL0 is off then.
We still have a separate warn at boot if cdclk is disabled (because we
don't currently try to handle the case (that shouldn't happen on SKL as
far as I know) where we boot with display not initialized.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add support for changing cdclk frequency during runtime on BDW.
Also with IPS enabled the actual pixel rate mustn't exceed 95% of cdclk,
so take that into account when computing the max pixel rate.
v2: Grab rps.hw_lock around sandybridge_pcode_write()
v3: Rebase due to power well vs. .global_resources() reordering
v4: Rebased to the latest
v5: Rebased to the latest
v6: Patch order shuffle so that Broadwell CD clock change is
applied before the patch for Haswell CD clock change
v7: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We need to tell BDW ULT and ULX apart.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bspec says we shouldn't enable IPS on BDW when the pipe pixel rate
exceeds 95% of the core display clock. Apparently this can cause
underruns.
There's no similar restriction listed for HSW, so leave that one alone
for now.
v2: Add pipe_config_supports_ips() (Chris)
v3: Compare against the max cdclk insted of the current cdclk
v4: Rebased to the latest
v5: Rebased to the latest
v6: Fix for patch style problems
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83497
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Keep the cdclk maximum supported frequency around in dev_priv so that we
can verify certain things against it before actually changing the cdclk
frequency.
For now only VLV/CHV have support changing cdclk frequency, so other
plarforms get to assume cdclk is fixed.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Rather than reading out the current cdclk value use the cached value we
have tucked away in dev_priv.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Rather that extracting the current cdclk freuqncy every time someone
wants to know it, cache the current value and use that. VLV/CHV already
stored a cached value there so just expand that to cover all platforms.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Rebased to the latest
v5: Removed spurious call to 'intel_update_cdclk(dev)' based on
Damien Lespiau's comment
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Main pull req for 4.2.. I think there will be a secondary pull-req..
I'd like to land the hdcp support patches, since all the review
comments have been long since addressed, and they have been ready to
merge for a couple release cycles now other than the scm dependency
(which should be coming in through arm-soc tree for 4.2). So I am not
including them in this initial pull req to avoid merge ordering
issues.
Main highlights:
1) adreno a306 support (for apq8x16 and upcoming dragonboard 410c)
2) various dsi bits
3) various 64bit fixes (mostly warnings)
4) NV12MT support, pulled in via msm-next rather than drm-misc since
dependency on on regenerated envytools headers (but lgtm'd-by danvet)
5) random fixes and cleanups
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (36 commits)
drm/msm: restart queued submits after hang
drm/msm: fix timeout calculation
drm/msm/hdmi: Use pinctrl in HDMI driver
drm/msm/hdmi: Point to the right struct device
drm/msm/mdp: Add support for more 32-bit RGB formats
drm/msm: use __s32, __s64, __u32 and __u64 from linux/types.h for uabi
drm/msm/atomic: Clean up planes in the error paths of .atomic_commit()
drm/msm/mdp5: Always generate active-high sync signals for DSI
drm/msm: dsi: fix compile errors when CONFIG_GPIOLIB=n
drm/msm: use devm_gpiod_get_optional for optional reset gpio
drm/msm/dsi: Separate PHY to another platform device
drm/msm/dsi: Enable PLL driver in MSM DSI
drm/msm/dsi: Add DSI PLL clock driver support
drm/msm: use IS_ERR() to check regulator_get() return
drm/msm: use IS_ERR() to check msm_ioremap() return
drm/msm/mdp5: Wait for PP_DONE irq for command mode CRTC atomic commit
drm/msm: Use customized function to wait for atomic commit done
dt-bindings: Add MSM eDP controller documentation
dt-bindings: Add MSM DSI controller documentation
drm/msm: drop redundant debug output
...
firmware name fix
* tag 'drm-intel-next-fixes-2015-06-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915/skl: Fix DMC API version in firmware file name
- Make the reset wavefronts action be per process per device instead of
per process, because one device can be stuck but the other one won't be
- Add some missing properties to the CZ device_info structure
- Rename symbols to not have CONFIG_ prefix
- Some more cleanups and debug prints
* tag 'drm-amdkfd-next-fixes-2015-06-10' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: remove not used defines from cik_regs.h
drm/amdkfd: Add missing properties to CZ device info
drm/amdkfd: make reset wavefronts per process per device
drm/amdkfd: add debug print to kfd_events.c
drm/amdkfd: avoid CONFIG_ prefix for non-Kconfig symbols
Mainly it is fixing timing on HDMI to be compliant with CEA-861E spec.
* '2015-06-08-st-drm-next' of http://git.linaro.org/people/benjamin.gaignard/kernel:
drm/sti: vtg fix CEA-861E video format timing error
drm/sti: hdmi fix CEA-861E video format timing error
drm/sti: VTG interrupt names are badly displayed
drm/sti: missing first pixel column on HDMI display
drm/sti: correctly test devm_ioremap() return
Track the list of in-flight submits. If the gpu hangs, retire up to an
including the offending submit, and then re-submit the remainder. This
way, for concurrently running piglit tests (for example), one failing
test doesn't cause unrelated tests to fail simply because it's submit
was queued up after one that triggered a hang.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The 'timeout' value comes from userspace (CLOCK_MONOTONIC), but
converting this directly to jiffies doesn't take into account the
initial jiffies count at boot, which may differ from the base time
of CLOCK_MONOTONIC.
TODO: add ktime_delta_jiffies() when rebasing on 4.1 and use that
instead of ktime_sub/ktime_to_timespec/timespec_to_jiffies combo (as
suggested by Arnd)
v2: switch over from 'struct timespec' to ktime_t throughout, since
'struct timespec' will be deprecated (as suggested by Arnd)
v3: minor cosmetic tweaks
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some targets (eg: msm8994) use the pinctrl framework to configure
interface pins. This change adds support for initialization and
pinctrl active/sleep state control for the HDMI driver.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DRM device's dev (hdmi->dev->dev) points to the mdss_mdp device
handle. Instead, we should get a reference to the mdss_hdmi
handle.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
That will complete the lists of Alpha + RGB formats.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When the .atomic_commit() handler fails, clean up planes previoulsy
prepared by drm_atomic_helper_prepare_planes() with a call to
drm_atomic_helper_cleanup_planes().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI video mode engine can only take active-high sync signals. This
change prevents MDP5 sending active-low sync signals to DSI in any
case.
Signed-off-by: Hai Li <hali@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
I'm not sure where, exactly, but somewhere in here we must be relying on
an implicit include.
drivers/gpu/drm/msm/dsi/dsi_host.c: In function ‘dsi_host_init_panel_gpios’:
drivers/gpu/drm/msm/dsi/dsi_host.c:1356:2: error: implicit declaration of function ‘devm_gpiod_get’ [-Werror=implicit-function-declaration]
msm_host->disp_en_gpio = devm_gpiod_get(panel_device,
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1356:25: warning: assignment makes pointer from integer without a cast [enabled by default]
msm_host->disp_en_gpio = devm_gpiod_get(panel_device,
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1364:3: error: implicit declaration of function ‘gpiod_direction_output’ [-Werror=implicit-function-declaration]
ret = gpiod_direction_output(msm_host->disp_en_gpio, 0);
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1371:20: warning: assignment makes pointer from integer without a cast [enabled by default]
msm_host->te_gpio = devm_gpiod_get(panel_device, "disp-te");
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1378:3: error: implicit declaration of function ‘gpiod_direction_input’ [-Werror=implicit-function-declaration]
ret = gpiod_direction_input(msm_host->te_gpio);
^
drivers/gpu/drm/msm/dsi/dsi_host.c: In function ‘msm_dsi_host_power_on’:
drivers/gpu/drm/msm/dsi/dsi_host.c:1918:3: error: implicit declaration of function ‘gpiod_set_value’ [-Werror=implicit-function-declaration]
gpiod_set_value(msm_host->disp_en_gpio, 1);
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Also there is a variant to find optional gpios that returns NULL if
there is no gpio instead of -ENOENT.
Make use of both features to simplify the driver.
This makes error checking more strict because errors like -ENOSYS ("no
gpio support compiled in") or -EPROBE_DEFER ("gpio not ready yet") are
handled correctly now.
Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are different types of PHY from one chipset to another, while
the DSI host controller is relatively consistent across platforms.
Also, the PLL inside PHY is providing the source of DSI byte and
pixel clocks, which are used by DSI host controller. Separated devices
for clock provider and clock consumer make DSI driver better fit into
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change activates PLL driver for DSI to work with
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI byte clock and pixel clocks are sourced from DSI PLL.
This change adds the DSI PLL source clock driver under
common clock framework.
This change handles DSI 28nm PLL only.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
regulator_get() never returns NULL. There's no need for IS_ERR_OR_NULL()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rob Clark <robdclark@gmail.com>
msm_ioremap() never returns NULL. There's no need for IS_ERR_OR_NULL()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rob Clark <robdclark@gmail.com>
CRTCs in DSI command mode data path should wait for pingpong done,
instead of vblank, to finish atomic commit.
This change is to enable PP_DONE irq on command mode CRTCs and wait for
this irq happens before atomic commit completion.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP FLUSH registers could indicate if the previous flush updates
has taken effect at vsync boundary. Making use of this H/W feature
can catch the vsync that happened between CRTC atomic_flush and
*_wait_for_vblanks, to avoid unnecessary wait.
This change allows kms CRTCs to use their own *_wait_for_commit_done
functions to wait for FLUSH register cleared at vsync, before commit
completion.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
wait_for_completion_timeout returns 0 in case of timeout and never
return < 0 so there is no additional information in printing the
value of time_left here as it will always be 0, thus it can be dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
wait_for_completion_timeout returns >= 0 but never
negative - so the error check should be against equality
to 0 not <= 0.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
return type of wait_for_completion_timeout is unsigned long not int, this
patch assigns the return value of wait_for_completion_timeout to an
appropriately typed and named variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some DSI peripherals rely on the HS clock on DSI clock lane as their clock
source. If the clock lane transitions between HS and LP states, it
can disrupt the functioning of such peripherals.
The mipi dsi mode flag MIPI_DSI_CLOCK_NON_CONTINUOUS already exists for
such peripheral drivers. Use it to configure the bit CLKLN_HS_FORCE_REQUEST
in DSI_LANE_CTRL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If the GEM object is imported, drm_prime_gem_destroy needs to be
called to clean up dma buffer related information.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Fix build warning when building edp/edp_aux.o due to missing
prototype for edp_aux_transfer.
This function is only used in edp_aux.c so just make it static.
Reported-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
wait_for_completion_timeout returns 0 in case of timeout so printing the
return value here will always yield 0 and is therefor redundant - dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The timeout is passed as a constant which makes it HZ dependent because
jiffies are expected so it should be converted to jiffies. The actual
value is not clear from the code - my best guess is that this should be
300 milliseconds given that other timeouts are in milliseconds based on
looking at other drm drivers (e.g. exynos_drm_dsi.c:356 300ms,
tegra/dpaux.c:188 250ms) - this needs to be confirmed by someone who
knows the details of the driver.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
wait_for_completion_timeout return >= 0 but never negative so the check
logic looks inconsistent. Further the return value of
wait_for_completion_timeout was being passed up the call chain but the
x call sites as drm_dp_i2c_do_msg()/drm_dp_dpcd_access() check for < 0
thus timeout was being treated as success case.
<snip> drivers/gpu/drm/drm_dp_helper.c:drm_dp_i2c_do_msg()
mutex_lock(&aux->hw_mutex);
ret = aux->transfer(aux, msg);
mutex_unlock(&aux->hw_mutex);
if (ret < 0) {
<snip>
logic in edp_aux_transfer() seems incorrect as it could return 0 (timeout)
but checks of <= 0 to indicate error so the return probably should be
-ETIMEDOUT in case wait_for_completion_timeout returns 0 (timeout
occurred).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Seems like disable can race with complete_flip() in process of disabling
a crtc, leading to:
[ 49.065364] Call trace:
[ 49.071441] [<ffffffc00041d5a0>] mdp5_ctl_blend+0x20/0x1c0
[ 49.073788] [<ffffffc00041ebcc>] mdp5_crtc_disable+0x3c/0xa8
[ 49.079348] [<ffffffc0003e7854>] disable_outputs.isra.4+0x11c/0x220
[ 49.085164] [<ffffffc0003e7afc>] drm_atomic_helper_commit_modeset_disables+0x14/0x38
[ 49.091155] [<ffffffc000425c80>] complete_commit+0x40/0xb8
[ 49.099136] [<ffffffc0004260ac>] msm_atomic_commit+0x364/0x398
[ 49.104430] [<ffffffc00040a614>] drm_atomic_commit+0x3c/0x70
[ 49.110249] [<ffffffc0003e67b8>] drm_atomic_helper_set_config+0x1b0/0x3e0
[ 49.116065] [<ffffffc0003f99bc>] drm_mode_set_config_internal+0x64/0xf8
[ 49.122746] [<ffffffc0003fa624>] drm_framebuffer_remove+0xe4/0x128
[ 49.129171] [<ffffffc0003feaf8>] drm_mode_rmfb+0xc0/0x100
[ 49.135420] [<ffffffc0003efba8>] drm_ioctl+0x258/0x4d0
[ 49.140889] [<ffffffc0001b0388>] do_vfs_ioctl+0x338/0x5d0
[ 49.145921] [<ffffffc0001b06a8>] SyS_ioctl+0x88/0xa0
It makes no sense to free the ctl without disabling all stages, so lets
just move them together to avoid the crash.
Signed-off-by: Rob Clark <robdclark@gmail.com>
As found in apq8016 (used in DragonBoard 410c) and msm8916.
Note that numerically a306 is actually 307 (since a305c already claimed
306). Nice and confusing.
Signed-off-by: Rob Clark <robdclark@gmail.com>
A few spots in the driver have support for downstream android
CONFIG_MSM_BUS_SCALING. This is mainly to simplify backporting the
driver for various devices which do not have sufficient upstream
kernel support. But the intentionally dead code seems to cause
some confusion. Rename the #define to make this more clear.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Using fb modifier flag, support NV12MT format in MDP4.
v2:
- rework the modifier's description [Daniel Vetter's comment]
- drop .set_mode_config() callback [Rob Clark's comment]
v3:
- change VENDOR's name and restrict usage to NV12 [pointed by Daniel]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Dump a bit more info when the GPU hangs, without having hang_debug
enabled (which dumps a *lot* of registers). Also dump the scratch
registers, as they are useful for determining where in the cmdstream
the GPU hung (and they seem always safe to read when GPU has hung).
Note that the freedreno gallium driver emits increasing counter values
to SCRATCH6 (to identify tile #) and SCRATCH7 (to identify draw #), so
these two in particular can be used to "triangulate" where in the
cmdstream the GPU hung.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The goto is correct, and we never reach the return statement so just
delete the dead code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
virtio_gpu_alloc_object() returns an error pointer, it never returns
NULL.
Fixes: dc5698e80c ('Add virtio gpu driver.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were doing it in the common code and in the IP specific code.
Remove the IP specific code. The common code handles the
ordering properly.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable VCE dpm and powergating. VCE dpm dynamically scales the VCE clocks on
demand.
Signed-off-by: Sonny Jiang <sonny.jiang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
smu_init allocates buffers and initializes them. It does not
touch the hw. There is no need to do it again on resume. It
should really be part of sw_init (and smu_fini should be part
of sw_fini), but we need the firmware sizes from the other IPs
for firmware loading so we have to wait until sw init is done
for all other IPs.
Reviewed-by: Sonny Jiang <Sonny.Jiang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smu_init allocates buffers and initializes them. It does not
touch the hw. There is no need to do it again on resume. It
should really be part of sw_init (and smu_fini should be part
of sw_fini), but we need the firmware sizes from the other IPs
for firmware loading so we have to wait until sw init is done
for all other IPs.
Reviewed-by: Sonny Jiang <Sonny.Jiang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smu_init allocates buffers and initializes them. It does not
touch the hw. There is no need to do it again on resume. It
should really be part of sw_init (and smu_fini should be part
of sw_fini), but we need the firmware sizes from the other IPs
for firmware loading so we have to wait until sw init is done
for all other IPs.
Reviewed-by: Sonny Jiang <Sonny.Jiang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some leftover copy and pastes from radeon that never
got updated.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to adjust the number of CUs and RBs.
v2: get proper values
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Samuel Li <samuel.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The driver makes use of this information so print if to aid in
debugging.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Samuel Li <samuel.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the unnecessary returned status and make the IOCTL write only.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
We need to reset the bo_va address, otherwise new mappings
wouldn't be updated in the page table.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
HDMI analyzer tests showed that Vsync and Hsync signal were not
compliant with the HDMI protocol.
HDMI_DELAY should be taken into account in the VTG Vsync
programming to reflect the 6 pixels shift introduced in the VTG
Hsync programming.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
HDMI analyzer tests showed that Vsync and Hsync signal were not
compliant with the HDMI protocol.
The first active pixel of a line is defined by HDMI_ACTIVE_VID_XMIN.
The last active pixel of a line is defined by HDMI_ACTIVE_VID_XMAX.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
VTG interrupt names are badly displayed using "cat /proc/interrupts".
Simply use the VTG device name while registering the VTG interrupts
to fix it.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
In case of error, the function devm_ioremap_nocache() returns NULL
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
This patch adds two missing properties initializations to the device
info structure of CZ.
As we don't have CZ support yet, it isn't critical, but its important to
fix this now instead of forgetting about it later.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This commit moves the reset wavefront flag to per process per device
data structure, so we can support multiple devices.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The CONFIG_ prefix is reserved for Kconfig options in Make and CPP
syntax. Various static analysis tools rely on this naming convention
and check if CONFIG_ prefixed symbols are defined Kconfig. Hence add
yet another prefix AMD_ to CONFIG_REG_{BASE,END,SISE} to apply to this
convention and make static analysis tools happy.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
amdgpu submits both kernel and user fences, but just need one interrupt,
disable user fence interrupt and don't effect user fence.
v2: fix merge error
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
There's some useless padding in the struct spi_driver definition. Remove
it since it serves no useful purpose.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both the Samsung LD9040 and Samsung S6E8AA0 panel drivers are missing
a const qualifier for their OF match tables. This data is static and
never changes, so can be read-only.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This header file declares prototypes of functions that are no longer
used. Remove this file and all references to it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If GPIOLIB=n and asm-generic/gpio.h is not used:
drivers/gpu/drm/bridge/ps8622.c: In function ‘ps8622_pre_enable’:
drivers/gpu/drm/bridge/ps8622.c:368: error: implicit declaration of function ‘gpiod_set_value’
drivers/gpu/drm/bridge/ps8622.c: In function ‘ps8622_probe’:
drivers/gpu/drm/bridge/ps8622.c:584: error: implicit declaration of function ‘devm_gpiod_get’
drivers/gpu/drm/bridge/ps8622.c:584: warning: assignment makes pointer from integer without a cast
drivers/gpu/drm/bridge/ps8622.c:590: error: implicit declaration of function ‘gpiod_direction_output’
drivers/gpu/drm/bridge/ps8622.c:596: warning: assignment makes pointer from integer without a cast
Add the missing #include <linux/gpio/consumer.h> to fix this.
Fixes: f1336e6afb ("drm/bridge: Add I2C based driver for ps8622/ps8625 bridge")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
If GPIOLIB=n and asm-generic/gpio.h is not used:
drivers/gpu/drm/bridge/ptn3460.c: In function ‘ptn3460_pre_enable’:
drivers/gpu/drm/bridge/ptn3460.c:135: error: implicit declaration of function ‘gpiod_set_value’
drivers/gpu/drm/bridge/ptn3460.c: In function ‘ptn3460_probe’:
drivers/gpu/drm/bridge/ptn3460.c:333: error: implicit declaration of function ‘devm_gpiod_get’
drivers/gpu/drm/bridge/ptn3460.c:333: warning: assignment makes pointer from integer without a cast
drivers/gpu/drm/bridge/ptn3460.c:340: error: implicit declaration of function ‘gpiod_direction_output’
drivers/gpu/drm/bridge/ptn3460.c:346: warning: assignment makes pointer from integer without a cast
Add the missing #include <linux/gpio/consumer.h> to fix this.
Fixes: af478d8823 ("drm/bridge: ptn3460: use gpiod interface")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
The dw_hdmi_connector_get_modes() function accidentally forgets to
return the number of modes it added, although it has this information
stored in a local variable. Let's fix that.
Without this fix, drm_helper_probe_single_connector_modes_merge_bits()
could get confused and always call drm_add_modes_noedid(). That's not
right.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
04 is the minor version. API version is ver1.
So let's follow same scheme used on published version at 01.org.
If really needed the minor version a follow-up updated will be
done. But for now we need to move fwd and unblock end users.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is the big pull request for amdgpu, the new driver for VI+ AMD
asics. I currently supports Tonga, Iceland, and Carrizo and also
contains a Kconfig option to build support for CI parts for testing.
All major functionality is supported (displays, gfx, compute, dma,
video decode/encode, etc.). Power management is working on Carrizo,
but is still being worked on for Tonga and Iceland.
* 'drm-next-4.2-amdgpu' of git://people.freedesktop.org/~agd5f/linux: (106 commits)
drm/amdgpu: only support IBs in the buffer list (v2)
drm/amdgpu: add vram_type and vram_bit_width for interface query (v2)
drm/amdgpu: add ib_size/start_alignment interface query
drm/amdgpu: add me/ce/pfp_feature_version interface query
drm/amdgpu add ce_ram_size for interface query
drm/amdgpu add max_memory_clock for interface query (v2)
drm/amdgpu: add hdp flush for gfx8 compute ring
drm/amdgpu: fix no hdp flush for compute ring
drm/amdgpu: add HEVC/H.265 UVD support
drm/amdgpu: stop loading firmware with pm.mutex locked
drm/amdgpu: remove mclk_lock
drm/amdgpu: fix description of vm_size module parameter (v2)
drm/amdgpu: remove all sh mem register modification in vm flush
drm/amdgpu: rename GEM_OP_SET_INITIAL_DOMAIN -> GEM_OP_SET_PLACEMENT
drm/amdgpu: fence should be added to shared slot
drm/amdgpu: sync fence of clear_invalids (v2)
drm/amdgpu: max_pde_used usage should be under protect
drm/amdgpu: fix bug of vm_bo_map (v2)
drm/amdgpu: implement the allocation range (v3)
drm/amdgpu: rename amdgpu_ip_funcs to amd_ip_funcs (v2)
...
This function could return a NULL pointer in case of handle not
present and in case of out of memory conditions however caller
function always returned EINVAL error hiding a possible ENOMEM.
This patch change the function to return the error instead to
be able to propagate the error instead of assuming EINVAL.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In qxlhw_handle_to_bo we incremented counters twice, one time for release object
and one for reloc_info.
In the main function however reloc_info references was drop much earlier than
release so keeping the pointer only on release is safe and make cleaning
process easier.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
qxl_bo structure has two reference counters, one in the GEM object and
another in the TTM object. The GEM object keep a counter to the TTM object
so when GEM counter reached zero the TTM counter (using qxl_bo_unref) was
decremented. The qxl object is fully freed (both GEM and TTM part are cleaned)
when the TTM counter reach zero.
One issue was that surface idr structure has no owning on qxl_bo objects however
it contains a pointer to qxl_bo object. This caused some nasty race condition
for instance qxl_bo object was reaped even after counter was already zero.
This patch fix these races moving main counter (the one used by qxl_bo_(un)ref)
to GEM object which cleanup routine (qxl_gem_object_free) remove the idr pointer
(using qxl_surface_evict) when the counters are still valid.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Enable format string checks for qxl_io_log and remove resulting warnings
which could lead to memory errors on different platform or just printing
wrong information.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Free resources correctly if function fails
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This function return handle to allocated release object which is an int.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only EBUSY error was handled. This could cause code to believe
reserve was successful while it failed.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Is we are not able to get source bo object from handle we free
destination bo object and call cleanup code however destination
object was already inserted in reloc_info array (num_relocs was
already incremented) so on cleanup we free destination again.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
reloc_info[i] is not still initialized in the print statement.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the function fails reference counter to the object is not decremented
causing leaks.
This is hard to spot as it happens only on very low memory situations.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If objects are moved back from system memory to VRAM (and spice id
created again) memory is already initialized so we need to set flag
to not clear memory.
If you don't do it after a while using desktop many images turns to
black or transparents.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
amdgpu_cs_find_mapping doesn't work without all buffers being validated,
so the TTM validation must be done first.
v2: only use amdgpu_cs_find_mapping for UVD/VCE VM emulation
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Track the type of vram on the board and provide a query for it.
User mode drivers and tools want this information for determining
bandwidth information and form informational purposes.
v2: fix build when CI support is not enabled
Signed-off-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Query the IB alignment requirements from the kernel rather
than hardcoding them in the user mode drivers.
Signed-off-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Provide this information to usermode drivers. We were previously
missing this info.
Signed-off-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Add a query for the CE ram size. User mode drivers
will want to use this to determine how much size
of the cache on the CE.
Signed-off-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewd-by: Jammy Zhou <Jammy.Zhou@amd.com>
Add a query for the max memory clock.
v2: handle the dpm enabled case properly
Signed-off-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewd-by: Jammy Zhou <Jammy.Zhou@amd.com>
We had forgotten to register the callback.
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: jammy zhou <jammy.zhou@amd.com>
Loading firmware is a rather complicated process, in the end we add a
dependency between the pm mutex and the mm semaphore which results in
a harmless but annoying error message.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Leave that at the values set during init. No need to update
them repeatedly.
Signed-off-by: monk.liu <monk.liu@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
bo_va may un-initialized, fix it.
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
Need to take the lock when accessing this.
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
call reservation_object_reserve_shared before amdgpu_bo_fence
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
Pass a ttm_placement pointer to amdgpu_bo_create_restricted
add min_offset to amdgpu_bo_pin_restricted. This makes it
easier to allocate memory with address restrictions. With
this patch we can also enable 2-ended allocation again.
v2: fix rebase conflicts
v3: memset placements before using
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The structure is renamed and moved to amd_shared.h to make
the component independent. This makes it easier to add
new components in the future.
v2: fix include path
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: yanyang1 <young.yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's causing issues with VMID handling and comparing the
fence value two times actually doesn't make handling faster.
Port of radeon commit "d6d5c5b8364bcc4d52cddc68bcb0a330d2af20f3".
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Enable UVD dpm (dynamic power management) and powergating. UVD dpm dynamically scales the UVD
clocks on demand. Powergating turns off the power to the block when it's not in use.
Signed-off-by: Sonny Jiang <sonny.jiang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
VCE 3.0 has two indentical instances in the engine, they share
the same registers name in differrent memory block distinguished
by the grbm_gfx_index, we set to master instance after init, it
will dispatch task to slave instance. These two instances will
share the same firmware, but have their own stacks and heaps.
v2: add mutex for using grbm_gfx_index
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Firmware required BO size changes in terms of ASIC family
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Deny user and kernel mapping if we said we never want to do so.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Retry the dpcd fetch several times. Some eDP panels
fail several times before the fetch is successful.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=73530
Ported from radeon.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use %*ph rather than walking the array.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Properly protect the state and also handle submission failures.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Otherwise a process can access the GDS data of another process.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
The CE preamble IB can be dropped for the same context
v2: use the flags directly
v3: remove 'CE' for potential preamble usage by other rings
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
check the filp is not robust, and sometimes different contexts may
have same filp value.
v2: check both filp and ctx_id
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
It is required to support fence per context.
v2: add amdgpu_ctx_get/put
v3: improve get/put
v4: squash hlock fix
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Set up the CP and SDMA for proper unaligned memory access.
Required for OpenCL 2.x
v2: udpate commit message
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
The existing locks were protecting the list, but not the elements.
v2: rename hlock to lock
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
If ctx was released between put and get, then "get" would crash.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
sg could point to array of contigiouse page*, only free page could lead
to memory leak.
v2: use iterator
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This flag isn't used by user mode drivers, remove it to avoid
confusion. And rename GTT_WC to GTT_USWC to make it clear.
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Avoids possibility that info may leak via the uninitialized
_pad element.
Noticed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
