Change type of active_fec to u32 to match the type expected by
mlx5e_get_fec_mode. Copy active_fec and configured_fec values to
unsigned long before preforming bitwise manipulations.
Take the same approach when configuring FEC over 50G link modes: copy
the policy into an unsigned long and only than preform bitwise
operations.
Fixes: 2132b71f78 ("net/mlx5e: Advertise globaly supported FEC modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On tunnel decap rule insertion, the indirect mechanism will attempt to
offload the rule on all uplink representors which will trigger the
"devices are not on same switch HW, can't offload forwarding" message
for the uplink which isn't on the same switch HW as the VF representor.
The above flow is valid and shouldn't cause warning message,
fix by removing the warning and only report this flow using extack.
Fixes: 321348475d ("net/mlx5e: Fix allowed tc redirect merged eswitch offload cases")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently a Linux system with the mlx5 NIC always crashes upon
hibernation - suspend/resume.
Add basic callbacks so the NIC could be suspended and resumed.
Fixes: 9603b61de1 ("mlx5: Move pci device handling from mlx5_ib to mlx5_core")
Tested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-05-29
1) Several fixes for ESP gro/gso in transport and beet mode when
IPv6 extension headers are present. From Xin Long.
2) Fix a wrong comment on XFRMA_OFFLOAD_DEV.
From Antony Antony.
3) Fix sk_destruct callback handling on ESP in TCP encapsulation.
From Sabrina Dubroca.
4) Fix a use after free in xfrm_output_gso when used with vxlan.
From Xin Long.
5) Fix secpath handling of VTI when used wiuth IPCOMP.
From Xin Long.
6) Fix an oops when deleting a x-netns xfrm interface.
From Nicolas Dichtel.
7) Fix a possible warning on policy updates. We had a case where it was
possible to add two policies with the same lookup keys.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern device tree bindings are supposed to be created as YAML-files
in accordance with dt-schema. This commit replaces two DW SPI legacy
bare text bindings with YAML file. As before the bindings file states
that the corresponding dts node is supposed to be compatible either
with generic DW APB SSI controller or with Microsemi/Amazon/Renesas/Intel
vendors-specific controllers, to have registers, interrupts and clocks
properties. Though in case of Microsemi version of the controller
there must be two registers resources specified. Properties like
clock-names, reg-io-width, cs-gpio, num-cs, DMA and slave device
sub-nodes are optional.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@vger.kernel.org
Link: https://lore.kernel.org/r/20200529182544.9807-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
It's better to understand what bits are set for DMA and for IRQ handling
in mid_spi_dma_setup() if they are grouped accordingly. Thus,
refactor mid_spi_dma_setup() to separate DMA and IRQ configuration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200529183150.44149-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 2afccbd283 ("spi: dw: Discard static DW DMA slave structures")
did a clean up of global variables, which is fine, but messed up with
the carefully provided information in the custom DMA slave structures.
There reader can find an assignment of the DMA request lines in use.
Partially revert the above mentioned commit to restore readability
and maintainability of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200529183150.44149-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit ecfbd3cf3b since Lukas Wunner noticed that we
start operating on the hardware before we check to see if this is a
spurious interrupt.
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals
Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW
APB SSI devices embedded into the SoC. Currently the DMA-based transfers
are supported by the DW APB SPI driver only as a middle layer code for
Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal
platform DMAC device we introduced a set of patches to fix it within this
series.
First of all we need to add the Tx and Rx DMA channels support into the DW
APB SSI binding. Then there are several fixes and cleanups provided as a
initial preparation for the Generic DMA support integration: add Tx/Rx
finish wait methods, clear DMAC register when done or stopped, Fix native
CS being unset, enable interrupts in accordance with DMA xfer mode,
discard static DW DMA slave structures, discard unused void priv pointer
and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst
length parametrisation and make sure it's optionally set in accordance
with the DMA max-burst capability.
In order to have the DW APB SSI MMIO driver working with DMA we need to
initialize the paddr field with the physical base address of the DW APB SSI
registers space. Then we unpin the Intel MID specific code from the
generic DMA one and placed it into the spi-dw-pci.c driver, which is a
better place for it anyway. After that the naming cleanups are performed
since the code is going to be used for a generic DMAC device. Finally the
Generic DMA initialization can be added to the generic version of the
DW APB SSI IP.
Last but not least we traditionally convert the legacy plain text-based
dt-binding file with yaml-based one and as a cherry on a cake replace
the manually written DebugFS registers read method with a ready-to-use
for the same purpose regset32 DebugFS interface usage.
This patchset is rebased and tested on the spi/for-next (5.7-rc5):
base-commit: fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next")
Link: https://lore.kernel.org/linux-spi/20200508132943.9826-1-Sergey.Semin@baikalelectronics.ru/
Changelog v2:
- Rebase on top of the spi repository for-next branch.
- Move bindings conversion patch to the tail of the series.
- Move fixes to the head of the series.
- Apply as many changes as possible to be applied the Generic DMA
functionality support is added and the spi-dw-mid is moved to the
spi-dw-dma driver.
- Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized"
since the problem has already been fixed.
- Add new patch "spi: dw: Discard unused void priv pointer".
- Add new patch "spi: dw: Discard dma_width member of the dw_spi structure".
n_bytes member of the DW SPI data can be used instead.
- Build the DMA functionality into the DW APB SSI core if required instead
of creating a separate kernel module.
- Use conditional statement instead of the ternary operator in the ref
clock getter.
Link: https://lore.kernel.org/linux-spi/20200515104758.6934-1-Sergey.Semin@baikalelectronics.ru/
Changelog v3:
- Use spi_delay_exec() method to wait for the DMA operation completion.
- Explicitly initialize the dw_dma_slave members on stack.
- Discard the dws->fifo_len utilization in the Tx FIFO DMA threshold
setting from the patch where we just add the default burst length
constants.
- Use min() method to calculate the optimal burst values.
- Add new patch which moves the spi-dw.c source file to spi-dw-core.c in
order to preserve the DW APB SSI core driver name.
- Add commas in the debugfs_reg32 structure initializer and after the last
entry of the dw_spi_dbgfs_regs array.
Link: https://lore.kernel.org/linux-spi/20200521012206.14472-1-Sergey.Semin@baikalelectronics.ru
Changelog v4:
- Get back ndelay() method to wait for an SPI transfer completion.
spi_delay_exec() isn't suitable for the atomic context.
Link: https://lore.kernel.org/linux-spi/20200522000806.7381-1-Sergey.Semin@baikalelectronics.ru
Changelog v5:
- Refactor the Tx/Rx DMA-based SPI transfers wait methods.
- Add a new patch "spi: dw: Set xfer effective_speed_hz".
- Add a new patch "spi: dw: Return any value retrieved from the
dma_transfer callback" as a preparation patch before implementing
the local DMA, Tx SPI and Rx SPI transfers wait methods.
- Add a new patch "spi: dw: Locally wait for the DMA transactions
completion", which provides a local DMA transaction complete
method
- Create a dedicated patch which adds the Rx-done wait method:
"spi: dw: Add SPI Rx-done wait method to DMA-based transfer".
- Add more detailed description of the problems the Tx/Rx-wait
methods-related patches fix.
- Wait for the SPI Tx and Rx transfers being finished in the
mid_spi_dma_transfer() method executed in the task context.
- Use spi_delay_exec() to wait for the SPI Tx/Rx completion, since now
the driver calls the wait methods in the kernel thread context.
- Use SPI_DELAY_UNIT_SCK spi_delay unit for Tx-wait delay, since SPI
xfer's are now have the effective_speed_hz initialized.
- Rx-wait for a delay correlated with the APB/SSI synchronous clock
rate instead of using the SPI bus clock rate.
Link: https://lore.kernel.org/linux-spi/20200529035915.20790-1-Sergey.Semin@baikalelectronics.ru
Changelog v6:
- Provide a more detailed description of the patch:
2901db35bea1 ("spi: dw: Locally wait for the DMA transfers completion")
- Calculate the Rx delay with better accuracy by moving 4-multiplication
to the head of the formulae:
ns = 4U * NSEC_PER_SEC / dws->max_freq * nents.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Ekaterina Skachko <Ekaterina.Skachko@baikalelectronics.ru>
Cc: Vadim Vlasov <V.Vlasov@baikalelectronics.ru>
Cc: Alexey Kolotnikov <Alexey.Kolotnikov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Serge Semin (16):
spi: dw: Set xfer effective_speed_hz
spi: dw: Return any value retrieved from the dma_transfer callback
spi: dw: Locally wait for the DMA transfers completion
spi: dw: Add SPI Tx-done wait method to DMA-based transfer
spi: dw: Add SPI Rx-done wait method to DMA-based transfer
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Fix Rx-only DMA transfers
spi: dw: Add core suffix to the DW APB SSI core source file
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Use regset32 DebugFS method to create regdump file
dt-bindings: spi: Convert DW SPI binding to DT schema
.../bindings/spi/snps,dw-apb-ssi.txt | 44 --
.../bindings/spi/snps,dw-apb-ssi.yaml | 127 +++++
.../devicetree/bindings/spi/spi-dw.txt | 24 -
drivers/spi/Kconfig | 15 +-
drivers/spi/Makefile | 5 +-
drivers/spi/{spi-dw.c => spi-dw-core.c} | 95 ++--
drivers/spi/spi-dw-dma.c | 482 ++++++++++++++++++
drivers/spi/spi-dw-mid.c | 382 --------------
drivers/spi/spi-dw-mmio.c | 4 +
drivers/spi/spi-dw-pci.c | 50 +-
drivers/spi/spi-dw.h | 20 +-
11 files changed, 719 insertions(+), 529 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
create mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml
delete mode 100644 Documentation/devicetree/bindings/spi/spi-dw.txt
rename drivers/spi/{spi-dw.c => spi-dw-core.c} (82%)
create mode 100644 drivers/spi/spi-dw-dma.c
delete mode 100644 drivers/spi/spi-dw-mid.c
--
2.26.2
Add mechanism to get the reset control and deassert it in order to bring
the IP out of reset.
Signed-off-by: Liang Jin J <liang.j.jin@ericsson.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20200529155806.16758-1-dinguyen@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm2711, Rasberry Pi 4's SoC, shares one interrupt for multiple
instances of the bcm2835 SPI controller. So this enables shared
interrupt support for them.
The early bail out in the interrupt routine avoids messing with buffers
of transfers being done by other means. Otherwise, the driver can handle
receiving interrupts asserted by other controllers during an IRQ based
transfer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200528185805.28991-1-nsaenzjulienne@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add new trace points for the start and end of enabling bypass on a
regulator, to allow monitoring of when regulators are moved into bypass
and how long that takes.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200529152216.9671-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix several issues in the previous gfs2_find_jhead fix:
* When updating @blocks_submitted, @block refers to the first block block not
submitted yet, not the last block submitted, so fix an off-by-one error.
* We want to ensure that @blocks_submitted is far enough ahead of @blocks_read
to guarantee that there is in-flight I/O. Otherwise, we'll eventually end up
waiting for pages that haven't been submitted, yet.
* It's much easier to compare the number of blocks added with the number of
blocks submitted to limit the maximum bio size.
* Even with bio chaining, we can keep adding blocks until we reach the maximum
bio size, as long as we stop at a page boundary. This simplifies the logic.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Bob Peterson <rpeterso@redhat.com>
Since the common code in the spi-dw-dma.c driver is ready to be used
by the MMIO driver and now provides a method to generically (on any
DT or ACPI-based platforms) retrieve the Tx/Rx DMA channel handlers,
we can use it and a set of the common DW SPI DMA callbacks to enable
DMA at least for generic "snps,dw-apb-ssi" and "snps,dwc-ssi-1.01a"
devices.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-15-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since from now the former Intel MID platform layer is used as a generic
DW SPI DMA module, let's alter the internal methods naming to be
DMA-related instead of having the "mid_" prefix.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since there is a generic method available to initialize the DW SPI DMA
interface on any DT and ACPI-based platforms, which in general can be
designed with not only DW DMAC but with any DMA engine on board, we can
freely remove the CONFIG_DW_DMAC_PCI config from dependency list of
CONFIG_SPI_DW_DMA. Especially seeing that we don't use anything DW DMAC
specific in the new driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a preparation patch before adding the DW DMA support into the
DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the
intended to be generic DW APB SSI DMA code. This isn't that hard,
since the most part of the spi-dw-mid.c driver in fact implements a
generic DMA interface for the DW SPI controller driver. The only Intel
MID specifics concern getting the max frequency from the MRST Clock
Control Unit and fetching the DMA controller channels from
corresponding PCIe DMA controller. Since first one is related with the
SPI interface configuration we moved it' implementation into the
DW PCIe-SPI driver module. After that former spi-dw-mid.c file
can be just renamed to be the DW SPI DMA module optionally compiled in to
the DW APB SSI core driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic DMA support is going to be part of the DW APB SSI core object.
In order to preserve the kernel loadable module name as spi-dw.ko, let's
add the "-core" suffix to the object with generic DW APB SSI code and
build it into the target spi-dw.ko driver.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Tx-only DMA transfers are working perfectly fine since in this case
the code just ignores the Rx FIFO overflow interrupts. But it turns
out the SPI Rx-only transfers are broken since nothing pushing any
data to the shift registers, so the Rx FIFO is left empty and the
SPI core subsystems just returns a timeout error. Since DW DMAC
driver doesn't support something like cyclic write operations of
a single byte to a device register, the only way to support the
Rx-only SPI transfers is to fake it by using a dummy Tx-buffer.
This is what we intend to fix in this commit by setting the
SPI_CONTROLLER_MUST_TX flag for DMA-capable platform.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Each channel of DMA controller may have a limited length of burst
transaction (number of IO operations performed at ones in a single
DMA client request). This parameter can be used to setup the most
optimal DMA Tx/Rx data level values. In order to avoid the Tx buffer
overrun we can set the DMA Tx level to be of FIFO depth minus the
maximum burst transactions length. To prevent the Rx buffer underflow
the DMA Rx level should be set to the maximum burst transactions length.
This commit setups the DMA channels and the DW SPI DMA Tx/Rx levels
in accordance with these rules.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
It isn't good to have numeric literals in the code especially if there
are multiple of them and they are related. Let's replace the Tx and Rx
burst level literals with the corresponding constants.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Having any data left in the Rx FIFO after the DMA engine claimed it has
finished all DMA transactions is an abnormal situation, since the DW SPI
controller driver expects to have all the data being fetched and placed
into the SPI Rx buffer at that moment. In case if that has happened we
hopefully assume that the DMA engine may still be doing the data fetching,
thus we give it sometime to finish. If after a short period of time the
data is still left in the Rx FIFO, the driver will give up waiting and
return an error indicating that the SPI controller/DMA engine must have
hung up or failed at some point of doing their duties.
Fixes: 7063c0d942 ("spi/dw_spi: add DMA support")
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since DMA transfers are performed asynchronously with actual SPI bus
transfers, then even if DMA transactions are finished it doesn't mean
all data is actually pushed to the SPI bus. Some data might still be
in the controller FIFO. This is specifically true for Tx-only transfers.
In this case if the next SPI transfer is recharged while a tail of the
previous one is still in FIFO, we'll loose that tail data. In order to
fix that problem let's add the wait procedure of the Tx SPI transfer
completion after the DMA transactions are finished.
Fixes: 7063c0d942 ("spi/dw_spi: add DMA support")
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In general each DMA-based SPI transfer can be split up into two stages:
DMA data transmission/reception and SPI-bus transmission/reception. DMA
asynchronous transactions completion can be tracked by means of the
DMA async Tx-descriptor completion callback. But that callback being
called indicates that the DMA transfer has been finished, it doesn't
mean that SPI data transmission is also done. Moreover in fact it isn't
for at least Tx-only SPI transfers. Upon DMA transfer completion some
data is left in the Tx FIFO and being pushed out by the SPI controller.
So in order to make sure that an SPI transfer is completely pushed to the
SPI-bus, the driver has to wait for both DMA transaction and the SPI-bus
transmission/reception are finished. Note if there is a way to
asynchronously track the former event by means of the DMA async Tx
callback, there isn't easy one for the later (IRQ-based solution won't
work since SPI controller doesn't notify about Rx FIFO being empty).
The DMA transfer completion callback isn't suitable to wait for the
SPI controller activity finish either. The callback might (in case of DW
DMAC it will) be called in the tasklet context. Waiting for the SPI
controller to complete the transfer might take a considerable amount of
time since SPI-bus might be pretty slow. In this case delaying the
execution in the tasklet atomic context might cause significant system
performance drop.
So to speak the best option we've got to solve the problem is to
consequently wait for both stages being finished in the locally
implemented SPI transfer execution procedure even if it costs us of the
local wait-function re-implementation. In this case we don't need to use
the SPI-core transfer-wait functionality, but we'll make sure that
all DMA and SPI-bus transactions are completely finished before the
SPI-core transfer_one callback returns. In this commit we provide an
implementation of the DMA-transfers completion wait functionality.
The DW APB SSI DMA-specific SPI transfer_one function waits for both
Tx and Rx DMA transfers being finished, and only then exits with zero
returned signalling to the SPI core that the SPI transfer is finished.
This implementation is fully equivalent to the currently used
DMA-execution-SPI-core-wait algorithm. The SPI-bus transmission/reception
wait methods will be added in the follow-up commits.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
DW APB SSI DMA-part of the driver may need to perform the requested
SPI-transfer synchronously. In that case the dma_transfer() callback
will return 0 as a marker of the SPI transfer being finished so the
SPI core doesn't need to wait and may proceed with the SPI message
trasnfers pumping procedure. This will be needed to fix the problem
when DMA transactions are finished, but there is still data left in
the SPI Tx/Rx FIFOs being sent/received. But for now make dma_transfer
to return 1 as the normal dw_spi_transfer_one() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Seeing DW APB SSI controller doesn't support setting the exactly
requested SPI bus frequency, but only a rounded frequency determined
by means of the odd-numbered half-worded reference clock divider,
it would be good to tune the SPI core up and initialize the current
transfer effective_speed_hz. By doing so the core will be able to
execute the xfer-related delays with better accuracy.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The Debian kernel v5.6 triggers this kernel panic:
Kernel panic - not syncing: Bad Address (null pointer deref?)
Bad Address (null pointer deref?): Code=26 (Data memory access rights trap) at addr 0000000000000000
CPU: 0 PID: 0 Comm: swapper Not tainted 5.6.0-2-parisc64 #1 Debian 5.6.14-1
IAOQ[0]: mem_init+0xb0/0x150
IAOQ[1]: mem_init+0xb4/0x150
RP(r2): start_kernel+0x6c8/0x1190
Backtrace:
[<0000000040101ab4>] start_kernel+0x6c8/0x1190
[<0000000040108574>] start_parisc+0x158/0x1b8
on a HP-PARISC rp3440 machine with this memory layout:
Memory Ranges:
0) Start 0x0000000000000000 End 0x000000003fffffff Size 1024 MB
1) Start 0x0000004040000000 End 0x00000040ffdfffff Size 3070 MB
Fix the crash by avoiding virt_to_page() and similar functions in
mem_init() until the memory zones have been fully set up.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.0+
Hi!
This patchset is another attempt to fix the regulator coupling on
Exynos5800/5422 SoCs. Here are links to the previous attempts:
https://lore.kernel.org/linux-samsung-soc/20191008101709.qVNy8eijBi0LynOteWFMnTg4GUwKG599n6OyYoX1Abs@z/https://lore.kernel.org/lkml/20191017102758.8104-1-m.szyprowski@samsung.com/https://lore.kernel.org/linux-pm/cover.1589528491.git.viresh.kumar@linaro.org/https://lore.kernel.org/linux-pm/20200528131130.17984-1-m.szyprowski@samsung.com/
The problem is with "vdd_int" regulator coupled with "vdd_arm" on Odroid
XU3/XU4 boards family. "vdd_arm" is handled by CPUfreq. "vdd_int" is
handled by devfreq. CPUfreq initialized quite early during boot and it
starts changing OPPs and "vdd_arm" value. Sometimes CPU activity during
boot goes down and some low-frequency OPPs are selected, what in turn
causes lowering "vdd_arm". This happens before devfreq applies its
requirements on "vdd_int". Regulator balancing code reduces "vdd_arm"
voltage value, what in turn causes lowering "vdd_int" value to the lowest
possible value. This is much below the operation point of the wcore bus,
which still runs at the highest frequency.
The issue was hard to notice because in the most cases the board managed
to boot properly, even when the regulator was set to lowest value allowed
by the regulator constraints. However, it caused some random issues,
which can be observed as "Unhandled prefetch abort" or low USB stability.
Adding more and more special cases to the generic code has been rejected,
so the only way to ensure the desired behavior on Exynos5800-based SoCs
is to make a custom regulator coupler driver.
Best regards,
Marek Szyprowski
Patch summary:
Marek Szyprowski (2):
regulator: extract voltage balancing code to separate function
soc: samsung: Add simple voltage coupler for Exynos5800
arch/arm/mach-exynos/Kconfig | 1 +
drivers/regulator/core.c | 49 ++++++++-------
drivers/soc/samsung/Kconfig | 3 +
drivers/soc/samsung/Makefile | 1 +
.../soc/samsung/exynos-regulator-coupler.c | 59 +++++++++++++++++++
include/linux/regulator/coupler.h | 8 +++
6 files changed, 101 insertions(+), 20 deletions(-)
create mode 100644 drivers/soc/samsung/exynos-regulator-coupler.c
--
2.17.1
base-commit: 8f3d9f3542
Move the coupled regulators voltage balancing code to the separate
function and allow to call it from the custom regulator couplers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200529124940.10675-2-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
kobject_init_and_add() takes reference even when it fails.
Thus, when kobject_init_and_add() returns an error,
kobject_put() must be called to properly clean up the kobject.
Fixes: d72e31c937 ("iommu: IOMMU Groups")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Link: https://lore.kernel.org/r/20200527210020.6522-1-wu000273@umn.edu
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The variable ret is being assigned with a value that is never read
and it is being updated later with a new value. The initialization is
redundant so remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200429154847.287001-1-colin.king@canonical.com
Bartosz Golaszewski <bgolaszewski@baylibre.com>:
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
I noticed that oftentimes I use regmap_update_bits() for simple bit
setting or clearing. In this case the fourth argument is superfluous as
it's always 0 or equal to the mask argument.
This series proposes to add simple bit operations for setting, clearing
and testing specific bits with regmap.
The second patch uses all three in a driver that got recently picked into
the net-next tree.
The patches obviously target different trees so - if you're ok with
the change itself - I propose you pick the first one into your regmap
tree for v5.8 and then I'll resend the second patch to add the first
user for these macros for v5.9.
v1 -> v2:
- convert the new macros to static inline functions
v2 -> v3:
- drop unneeded ternary operator
Bartosz Golaszewski (2):
regmap: provide helpers for simple bit operations
net: ethernet: mtk-star-emac: use regmap bitops
drivers/base/regmap/regmap.c | 22 +++++
drivers/net/ethernet/mediatek/mtk_star_emac.c | 80 ++++++++-----------
include/linux/regmap.h | 36 +++++++++
3 files changed, 93 insertions(+), 45 deletions(-)
base-commit: 8f3d9f3542
--
2.26.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Looking at the Felix and Ocelot drivers, Maxim asked if it would be
possible to use them as a base for a new driver for the switch inside
NXP T1040. Turns out, it is! The result is a driver eerily similar to
Felix.
The biggest challenge seems to be getting register read/write API
generic enough to cover such wild bitfield variations between hardware
generations. There is a patch on the regmap core which I would like to
get in through the networking subsystem, if possible (and if Mark is
ok), since it's a trivial addition.
Maxim Kochetkov (4):
soc/mscc: ocelot: add MII registers description
net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield
net: mscc: ocelot: extend watermark encoding function
net: dsa: ocelot: introduce driver for Seville VSC9953 switch
Vladimir Oltean (7):
regmap: add helper for per-port regfield initialization
net: mscc: ocelot: unexport ocelot_probe_port
net: mscc: ocelot: convert port registers to regmap
net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to
regfields
net: dsa: ocelot: create a template for the DSA tags on xmit
net: mscc: ocelot: split writes to pause frame enable bit and to
thresholds
net: mscc: ocelot: disable flow control on NPI interface
drivers/net/dsa/ocelot/Kconfig | 12 +
drivers/net/dsa/ocelot/Makefile | 6 +
drivers/net/dsa/ocelot/felix.c | 49 +-
drivers/net/dsa/ocelot/felix_vsc9959.c | 72 +-
drivers/net/dsa/ocelot/seville.c | 742 +++++++++++++++
drivers/net/dsa/ocelot/seville.h | 50 +
drivers/net/dsa/ocelot/seville_vsc9953.c | 1064 ++++++++++++++++++++++
drivers/net/ethernet/mscc/ocelot.c | 87 +-
drivers/net/ethernet/mscc/ocelot.h | 9 +-
drivers/net/ethernet/mscc/ocelot_board.c | 21 +-
drivers/net/ethernet/mscc/ocelot_io.c | 18 +-
drivers/net/ethernet/mscc/ocelot_regs.c | 57 ++
include/linux/regmap.h | 8 +
include/soc/mscc/ocelot.h | 68 +-
include/soc/mscc/ocelot_dev.h | 78 --
include/soc/mscc/ocelot_qsys.h | 13 -
include/soc/mscc/ocelot_sys.h | 23 -
net/dsa/tag_ocelot.c | 21 +-
18 files changed, 2196 insertions(+), 202 deletions(-)
create mode 100644 drivers/net/dsa/ocelot/seville.c
create mode 100644 drivers/net/dsa/ocelot/seville.h
create mode 100644 drivers/net/dsa/ocelot/seville_vsc9953.c
base-commit: 8f3d9f3542
--
2.25.1
In many instances regmap_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.
This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200528154503.26304-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Similar to the standalone regfields, add an initializer for the users
who need to set .id_size and .id_offset in order to use the
regmap_fields_update_bits_base API.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200527234113.2491988-2-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We provided the right semantics on open drain lines being
by definition output but incidentally the irq set up function
would only allow IRQs on lines that were "not output".
Fix the semantics to allow output open drain lines to be used
for IRQs.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Russell King <linux@armlinux.org.uk>
Cc: stable@vger.kernel.org # v5.3+
Link: https://lore.kernel.org/r/20200527140758.162280-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch is to fix a crash:
[ ] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ ] general protection fault: 0000 [#1] SMP KASAN PTI
[ ] RIP: 0010:ipv6_local_error+0xac/0x7a0
[ ] Call Trace:
[ ] xfrm6_local_error+0x1eb/0x300
[ ] xfrm_local_error+0x95/0x130
[ ] __xfrm6_output+0x65f/0xb50
[ ] xfrm6_output+0x106/0x46f
[ ] udp_tunnel6_xmit_skb+0x618/0xbf0 [ip6_udp_tunnel]
[ ] vxlan_xmit_one+0xbc6/0x2c60 [vxlan]
[ ] vxlan_xmit+0x6a0/0x4276 [vxlan]
[ ] dev_hard_start_xmit+0x165/0x820
[ ] __dev_queue_xmit+0x1ff0/0x2b90
[ ] ip_finish_output2+0xd3e/0x1480
[ ] ip_do_fragment+0x182d/0x2210
[ ] ip_output+0x1d0/0x510
[ ] ip_send_skb+0x37/0xa0
[ ] raw_sendmsg+0x1b4c/0x2b80
[ ] sock_sendmsg+0xc0/0x110
This occurred when sending a v4 skb over vxlan6 over ipsec, in which case
skb->protocol == htons(ETH_P_IPV6) while skb->sk->sk_family == AF_INET in
xfrm_local_error(). Then it will go to xfrm6_local_error() where it tries
to get ipv6 info from a ipv4 sk.
This issue was actually fixed by Commit 628e341f31 ("xfrm: make local
error reporting more robust"), but brought back by Commit 844d48746e
("xfrm: choose protocol family by skb protocol").
So to fix it, we should call xfrm6_local_error() only when skb->protocol
is htons(ETH_P_IPV6) and skb->sk->sk_family is AF_INET6.
Fixes: 844d48746e ("xfrm: choose protocol family by skb protocol")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
comparison
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXs+b2wAKCRDj7w1vZxhR
xdZ9AQC9uquqrOAGV8Falzp+Obu1MDp7nu8zrKH35jWt+UtONwEAk8TsnMAq7y18
Bi4cAke59vX/YLiMaN8EamJs67FGsw0=
=zcXf
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2020-05-28' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Two ingenic fixes, one for a wrong cast, the other for a typo in a
comparison
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200528110944.hanv4qgc6w7whnj3@gilmour.lan
Recent change in virtio_net_hdr_to_skb() broke some packetdrill tests.
When --mss=XXX option is set, packetdrill always provide gso_type & gso_size
for its inbound packets, regardless of packet size.
if (packet->tcp && packet->mss) {
if (packet->ipv4)
gso.gso_type = VIRTIO_NET_HDR_GSO_TCPV4;
else
gso.gso_type = VIRTIO_NET_HDR_GSO_TCPV6;
gso.gso_size = packet->mss;
}
Since many other programs could do the same, relax virtio_net_hdr_to_skb()
to no longer return an error, but instead ignore gso settings.
This keeps Willem intent to make sure no malicious packet could
reach gso stack.
Note that TCP stack has a special logic in tcp_set_skb_tso_segs()
to clear gso_size for small packets.
Fixes: 6dd912f826 ("net: check untrusted gso_size at kernel entry")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
