NAND, from Boris:
"""
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
SPI NOR, from Cyrille:
"""
- fixes in the hisi SPI controller driver.
- fixes in the intel SPI controller driver.
- fixes in the Mediatek SPI controller driver.
- fixes to some SPI flash memories not supported the Chip Erase command.
- add support to some new memory parts (Winbond, Macronix, Micron, ESMT).
- add new driver for the STM32 QSPI controller.
"""
And a few fixes for Gemini and Versatile platforms on physmap-of
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dxj5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
Nandsim has own functions set_memalloc() and clear_memalloc() for robust
setting and clearing of PF_MEMALLOC. Replace them by the new generic
helpers. No functional change.
Link: http://lkml.kernel.org/r/20170405074700.29871-5-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old 1-bit hamming layout requires ECC data to be placed at a
fixed offset, and not necessarily at the end of the OOB area.
Add this old layout back in order to fix legacy setups.
Fixes: 41b207a70d ("mtd: nand: implement the default mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We only need to allocate sizeof(struct oxnas_nand_ctrl) which is 192
bytes and not sizeof(struct nand_chip) which is a much larger 3056
bytes.
Fixes: 6685924924 ("mtd: nand: Add OX820 NAND Support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4jGH
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.12' of github.com:linux-nand/linux into MTD
From Boris:
"""
This pull request contains:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
On brcmnand controller v6.x and v7.x, the #WP pin is controlled through
the NAND_WP bit in CS_SELECT register.
The driver currently assumes that toggling the #WP pin is
instantaneously enabling/disabling write-protection, but it actually
takes some time to propagate the new state to the internal NAND chip
logic. This behavior is sometime causing data corruptions when an
erase/program operation is executed before write-protection has really
been disabled.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add a comment clarifying that NAND subpage write on keystone works,
but is not being enabled in the interest of backward compatibility.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
commit c9711ec525 ("mtd: nand: omap: Clean up device tree support")
caused the parent device name to be changed from "omap2-nand.0"
to "<base address>.nand" (e.g. 30000000.nand on omap3 platforms).
This caused mtd->name to be changed as well. This breaks partition
creation via mtdparts passed by u-boot as it uses "omap2-nand.0"
for the mtd-id.
Fix this by explicitly setting the mtd->name to "omap2-nand.<CS number>"
if it isn't already set by nand_set_flash_node(). CS number is the
NAND controller instance ID.
Fixes: c9711ec525 ("mtd: nand: omap: Clean up device tree support")
Cc: <stable@vger.kernel.org> # 4.7+
Reported-by: Leto Enrico <enrico.leto@siemens.com>
Reported-by: Adam Ford <aford173@gmail.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We accidentally return 1 on error instead of proper error codes.
Fixes: 07b23e3db9ed ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In some cases, nand_do_{read,write}_ops is passed with unaligned
ops->datbuf. Drivers using DMA will be unhappy about unaligned
buffer.
The new struct member, buf_align, represents the minimum alignment
the driver require for the buffer. If the buffer passed from the
upper MTD layer does not have enough alignment, nand_do_*_ops will
use bufpoi.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some NAND controllers are using DMA engine requiring a specific
buffer alignment. The core provides no guarantee on the nand_buffers
pointers, which forces some drivers to allocate their own buffers
and pass the NAND_OWN_BUFFERS flag.
Rework the nand_buffers allocation logic to allocate each buffer
independently. This should make most NAND controllers/DMA engine
happy, and allow us to get rid of these custom buf allocation in
NAND controller drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 271707b1d8 ("mtd: nand: denali: max_banks calculation
changed in revision 5.1") added a revision check to support the
new max_banks encoding. Its git-log states "The encoding of
max_banks changed in Denali revision 5.1".
There are exceptional cases, for example, the revision register on
some UniPhier SoCs says the IP is 5.0 but the max_banks is encoded
in the new format.
This IP updates the resister specification from time to time (often
breaking the backward compatibility), but the revision number is not
incremented correctly.
The max_banks is not only the case that needs revision checking.
Let's allow to override an incorrect revision number.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
"pdev" is much more often used to point a platform_device, so this
will help the driver code look consistent across the kernel.
While we are here, fix "line over 80 characters" coding style
violations.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The driver sets appropriate DMA mask. Delete the "dma-mask" DT
property. See [1] for negative comments for this binding.
[1] https://lkml.org/lkml/2016/2/8/57
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The current driver only supports the DMA engine up to 32 bit
physical address, but there also exists 64 bit capable DMA engine
for this IP.
The data DMA setup sequence is completely different, so I added the
64 bit DMA code as a new function denali_setup_dma64(). The 32 bit
one has been renamed to denali_setup_dma32().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There are various customizable parameters, so several variants for
this IP. A generic compatible like "denali,denali-nand-dt" is
useless. Moreover, there are multiple things wrong with this string.
(Refer to Rob's comment [1])
The "denali,denali-nand-dt" was added by Altera for the SOCFPGA port.
Replace it with a more specific string "altr,socfpga-denali-nand".
There are no users (in upstream) of the old compatible string.
The Denali IP on SOCFPGA incorporates the hardware ECC fixup engine.
So, this capability should be associated with the compatible.
[1] https://lkml.org/lkml/2016/12/1/450
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some old versions of the Denali IP (perhaps used only for Intel?)
detects ECC errors and provides correct data via a register, but
does not touch the transferred data. So, the software must fixup
the data in the buffer according to the provided ECC correction
information.
Newer versions perform ECC correction before transferring the data.
No more software intervention is needed. The ECC_ERROR_ADDRESS and
ECC_CORRECTION_INFO registers were deprecated. Instead, the number
of corrected bit-flips are reported via the ECC_COR_INFO register.
When an uncorrectable ECC error happens, a status flag is set to the
INTR_STATUS and ECC_COR_INFO registers.
As is often the case with this IP, the register view of INTR_STATUS
had broken compatibility.
For older versions (SW ECC fixup):
bit 0: ECC_TRANSACTION_DONE
bit 1: ECC_ERR
For newer versions (HW ECC fixup):
bit 0: ECC_UNCOR_ERR
bit 1: Reserved
Due to this difference, the irq_mask must be fixed too.
The existing handle_ecc() has been renamed to denali_sw_ecc_fixup()
for clarification.
What is unfortunate with this feature is we can not know the total
number of corrected/uncorrected errors in a page. The register
ECC_COR_INFO reports the maximum of per-sector bitflips. This is
useful for ->read_page return value, but ecc_stats.{corrected,failed}
increments may not be precise.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This part is wrong in multiple ways:
[1] is_erased() is called against "buf" twice, so the OOB area is
not checked at all. The second call should check chip->oob_poi.
[2] This code block is nested by double "if (check_erase_page)".
The inner one is redundant.
[3] The ECC_ERROR_ADDRESS register reports which sector(s) had
uncorrectable ECC errors. It is pointless to check the whole page
if only one sector contains errors.
[4] Unfortunately, the Denali ECC correction engine has already
manipulated the data buffer before it decides the bitflips are
uncorrectable. That is, not all of the data are 0xFF after an
erased page is processed by the ECC engine. The current is_erased()
helper could report false-positive ECC errors. Actually, a certain
mount of bitflips are allowed in an erased page. The core framework
provides nand_check_erased_ecc_chunk() that takes the threshold into
account. Let's use this.
This commit reworks the code to solve those problems.
Please note the erased page checking is implemented as a separate
helper function instead of embedding it in the loop in handle_ecc().
The reason is that OOB data are needed for the erased page checking,
but the controller can not start a new transaction until all ECC
error information is read out from the registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This function is wrong in multiple ways:
[1] Counting corrected bytes instead of corrected bits.
The following code is counting the number of corrected _bytes_.
/* correct the ECC error */
buf[offset] ^= err_cor_value;
mtd->ecc_stats.corrected++;
bitflips++;
What the core framework expects is the number of corrected _bits_.
They can be different if multiple bitflips occur within one byte.
[2] total number of errors instead of max of per-sector errors
The core framework expects that corrected errors are counted per
sector, then the max value should be taken. The current code simply
iterates over the whole page, i.e. counts the total number of
correction in the page. This means "too many bitflips" is triggered
earlier than it should be, i.e. the NAND device is worn out sooner.
Besides those bugs, this function is unreadable due to the deep
nesting. Notice the whole code in this function is wrapped in
if (irq_status & INTR__ECC_ERR), so this conditional can be moved
out of the function. Also, use shorter names for local variables.
Re-work the function to fix all the issues.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The pipeline read-ahead function of the Denali IP enables continuous
reading from the device; while data is being read out by a CPU, the
controller maintains additional commands for streaming data from the
device. This will reduce the latency of the second page or later.
This feature is obviously no help for per-page accessors of Linux
NAND driver interface.
In the current implementation, the pipeline command is issued to
load a single page, then data are read out immediately. The use of
the pipeline operation is not adding any advantage, but just adding
complexity to the code. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 28309572aa ("mtd: name the mtd device with an optional
label property") allow us to identify a chip in a user-friendly way.
If nand_set_flash_node() picks up the "label" from DT, let's respect
it. Otherwise, let it fallback to the current name "denali-nand".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The comment for ecc.read_page() requires that it should return
"0 if bitflips uncorrectable".
Actually, drivers could return positive values when uncorrectable
bitflips occur. For example, nand_read_page_swecc() is the case.
If ecc.correct() returns -EBADMSG for the first ECC sector, and
a positive value for the second one, nand_read_page_swecc() returns
a positive max_bitflips and increments ecc_stats.failed for the same
page.
The requirement can be relaxed by tweaking nand_do_read_ops().
Move the max_bitflips calculation below the retry.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The last/only user of the chip->write_page() hook (the Atmel NAND
controller driver) has been reworked and is no longer specifying a custom
->write_page() implementation.
Drop this hook before someone else start abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is a complete rewrite of the driver whose main purpose is to
support the new DT representation where the NAND controller node is now
really visible in the DT and appears under the EBI bus. With this new
representation, we can add other devices under the EBI bus without
risking pinmuxing conflicts (the NAND controller is under the EBI
bus logic and as such, share some of its pins with other devices
connected on this bus).
Even though the goal of this rework was not necessarily to add new
features, the new driver has been designed with this in mind. With a
clearer separation between the different blocks and different IP
revisions, adding new functionalities should be easier (we already
have plans to support SMC timing configuration so that we no longer
have to rely on the configuration done by the bootloader/bootstrap).
Also note that we no longer have a custom ->cmdfunc() implementation,
which means we can now benefit from new features added in the core
implementation for free (support for new NAND operations for example).
The last thing that we gain with this rework is support for multi-chips
and multi-dies chips, thanks to the clean NAND controller <-> NAND
devices representation.
During this transition we also dropped support for AVR32 SoCs which
should soon disappear from mainline (removal of the AVR32 arch is
planned for 4.12).
This new driver has been tested on several platforms (at91sam9261,
at91sam9g45, at91sam9x5, sama5d3 and sama5d4) to make sure it did not
introduce regressions, and it's worth mentioning that old bindings are
still supported (which partly explain the positive diffstat).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
To enable eventual removal of pr_warning
This makes pr_warn use consistent for drivers/mtd
Prior to this patch, there were 7 uses of pr_warning and
31 uses of pr_warn in drivers/mtd
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The clock gate used by orion_nand is not available on all platforms.
When getting this optional clock gate, the code masked all errors.
Let's be more precise here and actually only allow ENOENT.
EPROBE_DEFER is handled like any other error code since probe deferral
is not supported by drivers using module_platform_driver_probe().
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The clk handling in orion_nand.c had two problems:
- In the probe function, clk_put() was called for an enabled clock,
which violates the API (see documentation for clk_put() in
include/linux/clk.h)
- In the error path of the probe function, clk_put() could be called
twice for the same clock.
In order to clean this up, use the managed function devm_clk_get() and
store the pointer to the clk in the driver data.
Fixes: baffab28b1 ('ARM: Orion: fix driver probe error handling with respect to clk')
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Because SUPPORT_15BITECC is defined, the following is dead code:
#elif SUPPORT_8BITECC
iowrite32(8, denali->flash_reg + ECC_CORRECTION);
#endif
Such ifdefs are useless and unacceptable coding style.
These writes are not needed in the first place since ECC_CORRECTION
is set up by the nand_init() function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The write accesses to LOGICAL_PAGE_{DATA,SPARE}_SIZE have no effect
because the Denali User's Guide says these registers are read-only.
The hardware automatically multiplies the main/spare size by the
number of devices and update LOGICAL_PAGE_{DATA,SPARE}_SIZE.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, the driver expects DEVICE_CONNECTED is automatically set
by the hardware, but this feature is disabled in some cases.
In such cases, it is the software's responsibility to set up the
DEVICES_CONNECTED register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The available configuration of the IP bus width is x8 or x16, so the
possible value for denali->devnum is 1 or 2.
If the value is 1, there is nothing to do. Fixup parameters only
when denali->devnum is 2.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Collect multi NAND fixups into a helper function instead of
scattering them in denali_init().
I am rewording the comment block to clearly explain what is called
"multi device".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This will allow nand_dt_init() to parse DT properties in the NAND
controller device node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The denali_init() needs to setup a bunch of parameters of nand_chip.
Replace denali->nand.(member) with chip->(member) for shorter code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Set Features (0xEF) command toggles the R/B# pin after 4 sub feature
parameters are written.
Currently, nand_command(_lp) calls chip->dev_ready immediately after
the address cycle because NAND_CMD_SET_FEATURES falls into default:
label. No wait is needed at this point.
If you see nand_onfi_set_features(), R/B# is already cared by the
chip->waitfunc call.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Read ID (0x90) command does not toggle the R/B# pin. Without this
patch, NAND_CMD_READID falls into the default: label, then R/B# is
checked by chip->dev_ready().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The page number is generally stored in an integer type variable.
The uint16_t does not have enough width. I see no reason to use
uint32_t for other members, either. Just use int.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Denali NAND controller IP has various customizable features.
SoC vendors can choose desired functions when a delivery RTL is
created. It means there are several variants for this IP. For
example, the Intel version is equipped with 32bit DMA, whereas the
IP for UniPhier SoC family with 64bit DMA.
This driver was originally written for some Intel platforms with
Intel specific things hard-coded. What is worse, the revision
register of this IP does not work to distinguish such features.
We need to do something to make the driver available for other SoCs.
Let's introduce a caps member to the denali_nand_info structure to
switch on/off various features. Also, add struct denali_dt_data to
store the capability associated with compatible string.
Boris suggested this approach in discussion [1] instead of a new DT
property for every feature.
[1] https://lkml.org/lkml/2016/3/29/142
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The interrupts are enabled by INTR_EN register, then asserted
interrupts can be observed via INTR_STATUS register.
The bit fields are identical between INTR_EN and INTR_STATUS, so we
can merge the bit field macros. Likewise for DATA_INTR.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The same comment "Mapped io reg base address" for flash_reg and
flash_mem probably due to the mistake of copy-paste work.
Of course, the latter is not the register base address.
Reword the comments using the terminology in the Denali User's Guide.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
These members are not used at all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This macro is defined twice in denali.c (around line 98 and
line 651), so remove the second one.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All of these macros are not used at all.
CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR is not used for anything but
defining SCRATCH_REG_ADDR. The config option should go away as well.
I am removing some register macros. They are not used, and do not
exist in recent IP versions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_default_block_markbad() and scan_block_fast() use high
level APIs to get access to the BBM.
On the other hand, nand_block_bad (the default implementation of
->block_bad) calls the lower level ->cmdfunc hook. This prevents
drivers from using ->ecc.read_oob() even if optimized read operation
is implemented. Besides, some NAND controllers may protect the BBM
with ECC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, it is valid to specify both "nand-ecc-step-size" and
"nand-ecc-strength", but not allowed to set only one of them.
This requirement has a conflict with "nand-ecc-maximize"; this flag
is used when you want the driver to choose the best ECC strength.
If "nand-ecc-maximize" is set, "nand-ecc-strength" is very likely to
be unset.
It would be possible to make the if-conditional more complex by
adding the check for the NAND_ECC_MAXIMIZE flag, but I chose to drop
the check entirely. I thought of the situation where the hardware
has a fixed ECC step size (so it can be hard-coded in the driver),
whereas the ECC strength is configurable by software. In that case,
we may want to only set "nand-ecc-strength" (or "nand-ecc-maximize")
in DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Since commit 4404d7d821 ("mtd: nand: fsmc: remove stale non-DT probe
path"), the fsmc NAND driver only supports Device Tree probing, and
therefore has a "depends on OF" in its Kconfig option.
Due to this the #ifdef CONFIG_OF ... #endif condition in the driver code
is no longer necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
These definitions are not used anywhere in the driver, so remove them.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This commit switches the fsmc_nand driver from clk_get() to
devm_clk_get(), which saves a few clk_put().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Since the driver now only supports DT probing, it doesn't make a lot of
sense to have a private data structure called platform_data, fill it in
with information coming from the DT, and then copying this into the
driver-specific structure fsmc_nand_data.
So instead, we remove fsmc_nand_platform_data entirely, and have
fsmc_nand_probe_config_dt() fill in the fsmc_nand_data structure
directly.
This requires calling fsmc_nand_probe_config_dt() after fsmc_nand_data
has been allocated instead of before.
Also, as an added bonus, we now propagate properly the return value of
fsmc_nand_probe_config_dt() instead of returning -ENODEV on failure. The
error message is also removed, since it no longer made any sense.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
