A call to ->request() is always paired by a call to ->free() before a
given device is disposed. So the simplification that usually is possible
when using devm_*() functions cannot be used here. So use plain
kzalloc() and kfree() for improved runtime behaviour and reduced memory
footprint.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[thierry.reding@gmail.com: fix build failure]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
After a PWM is disposed by its user the per chip data becomes invalid.
Clear the data in common code instead of the device drivers to get
consistent behaviour. Before this patch only three of nine drivers
cleaned up here.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Fix suspend/resume support:
- add disabled_mask to struct samsung_pwm_chip to track PWM
disabled state information in pwm_samsung_{disable,enable}()
- rename pwm_samsung_config() to __pwm_samsung_config() and
add extra force_period parameter to be used during resume
(to force tin_ns and tcnt recalculation)
- add pwm_samsung_config() wrapper for preserving old behavior
- properly restore PWM configuration in pwm_samsung_resume()
- remove no longer needed pwm_samsung_suspend()
- update Copyrights
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
If the requested period_ns and duty_ns values are identical to the last
programmed ones pwm_samsung_config() returns early and skips the
hardware configuration. The same checks are now done by the PWM core so
the driver specific ones can be removed.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
From pwm_samsung_calc_tin(), there is routine to find the lowest divider
possible to generate lower frequency than requested one. But it is
always possible to generate requested frequency with large enough
modulation bits except on s3c24xx, so this patch fixes to use lowest div
for the case. This patch removes following UBSAN warning:
UBSAN: Undefined behaviour in drivers/pwm/pwm-samsung.c:197:13
shift exponent 32 is too large for 32-bit type 'long unsigned int'
[...]
[<c0670248>] (ubsan_epilogue) from [<c06707b4>] (__ubsan_handle_shift_out_of_bounds+0xd8/0x120)
[<c06707b4>] (__ubsan_handle_shift_out_of_bounds) from [<c0694b28>] (pwm_samsung_config+0x508/0x6a4)
[<c0694b28>] (pwm_samsung_config) from [<c069286c>] (pwm_apply_state+0x174/0x40c)
[<c069286c>] (pwm_apply_state) from [<c0b2e070>] (pwm_fan_probe+0xc8/0x488)
[<c0b2e070>] (pwm_fan_probe) from [<c07ba8b0>] (platform_drv_probe+0x70/0x150)
[...]
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
If the pwm-samsung driver is built as a module, modalias information is
not filled so the module is not autoloaded. Use the MODULE_DEVICE_TABLE()
macro to export the OF device ID so the module contains that information.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When disabling the Samsung PWM the output state remains at the level it
was at the end of a PWM cycle. In other words, calling pwm_disable()
when at 100% duty cycle will keep the output active, while at all other
settings the output will go/stay inactive. On top of that the Samsung
PWM settings are double-buffered, which means the new settings only get
applied at the start of a new PWM cycle.
This results in a race if the PWM is at 100% duty cycle and a driver
calls:
pwm_config(pwm, 0, period);
pwm_disable(pwm);
In this case the PWMs output will unexpectedly stay active, unless a new
PWM cycle happened to start between the register writes in pwm_config()
and pwm_disable(). As far as I can tell this is a regression introduced
by 3bdf878, before that a call to pwm_config() would call
pwm_samsung_enable() which, while heavy-handed, made sure the expected
settings were live.
To resolve this, while not re-introducing the issues 3bdf878 (flickering
as the PWM got reset while in a PWM cycle) fixed, only force an update
of the settings when at 100% duty cycle, which shouldn't have any
noticeable effect on the output but is enough to ensure the behaviour is
as expected on disable.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwm_samsung_config() sets the manual update bit via a call to the
pwm_samsung_enable() function even when the channel is already running.
This causes noticable flicker on display if we try to change the
backlight brightness from minimum to maximum, continuously.
So, we remove the call to pwm_samsung_enable() from pwm_samsung_config
to avoid the flicker and this change doesn't harm normal working since
the pwm-backlight driver already calls pwm_samsung_enable() where
needed.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
PWM channel data was set to NULL before freeing it. This caused the
following kernel warning while unexporting the channel. Set the channel
data to NULL after freeing it.
[ 70.495000] WARNING: CPU: 0 PID: 1 at drivers/base/devres.c:805 pwm_put+0x48/0x80()
[ 70.505000] Modules linked in:
[ 70.505000] CPU: 0 PID: 1 Comm: sh Not tainted 3.12.0-rc6-next-20131024-00012-gd4aec04-dirty #58
[ 70.515000] [<c0014ddc>] (unwind_backtrace+0x0/0xf4) from [<c0011784>] (show_stack+0x10/0x14)
[ 70.525000] [<c0011784>] (show_stack+0x10/0x14) from [<c03a3cbc>] (dump_stack+0x7c/0xb0)
[ 70.530000] [<c03a3cbc>] (dump_stack+0x7c/0xb0) from [<c001de68>] (warn_slowpath_common+0x6c/0x88)
[ 70.540000] [<c001de68>] (warn_slowpath_common+0x6c/0x88) from [<c001df20>] (warn_slowpath_null+0x1c/0x24)
[ 70.550000] [<c001df20>] (warn_slowpath_null+0x1c/0x24) from [<c01d1af8>] (pwm_put+0x48/0x80)
[ 70.560000] [<c01d1af8>] (pwm_put+0x48/0x80) from [<c01d21c8>] (pwm_unexport_store+0x94/0xac)
[ 70.565000] [<c01d21c8>] (pwm_unexport_store+0x94/0xac) from [<c010991c>] (sysfs_write_file+0x148/0x1d8)
[ 70.575000] [<c010991c>] (sysfs_write_file+0x148/0x1d8) from [<c00b2a80>] (vfs_write+0xb4/0x1a0)
[ 70.585000] [<c00b2a80>] (vfs_write+0xb4/0x1a0) from [<c00b3068>] (SyS_write+0x3c/0x78)
[ 70.595000] [<c00b3068>] (SyS_write+0x3c/0x78) from [<c000e2e0>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch introduces new Samsung PWM driver, which is completely
rewritten to be multiplatform- and DeviceTree-aware.
In addition, remaining problems of old driver are fixed, such as:
- proper handling of hardware variants,
- synchronization on SMP systems,
- handling of boundary parameter values,
- hardware sharing with PWM clocksource driver,
- undefined state of PWM output after stopping PWM channel.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Brown <broonie@linaro.org>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
This patch renames the old pwm-samsung driver to pwm-samsung-legacy to
create place for the new, rewritten, DT-aware pwm-samsung driver.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Brown <broonie@linaro.org>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Instead of using legacy suspend/resume methods, using newer dev_pm_ops
structure allows better control over power management.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
A new driver has been added for the SPEAr platform and the TWL4030/6030
driver has been replaced by two drivers that control the regular PWMs
and the PWM driven LEDs provided by the chips.
The vt8500, tiecap, tiehrpwm, i.MX, LPC32xx and Samsung drivers have all
been improved and the device tree bindings now support the PWM signal
polarity.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=m+7I
-----END PGP SIGNATURE-----
Merge tag 'for-3.8-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"A new driver has been added for the SPEAr platform and the
TWL4030/6030 driver has been replaced by two drivers that control the
regular PWMs and the PWM driven LEDs provided by the chips.
The vt8500, tiecap, tiehrpwm, i.MX, LPC32xx and Samsung drivers have
all been improved and the device tree bindings now support the PWM
signal polarity."
Fix up trivial conflicts due to __devinit/exit removal.
* tag 'for-3.8-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (21 commits)
pwm: samsung: add missing s3c->pwm_id assignment
pwm: lpc32xx: Set the chip base for dynamic allocation
pwm: lpc32xx: Properly disable the clock on device removal
pwm: lpc32xx: Fix the PWM polarity
pwm: i.MX: eliminate build warning
pwm: Export of_pwm_xlate_with_flags()
pwm: Remove pwm-twl6030 driver
pwm: New driver to support PWM driven LEDs on TWL4030/6030 series of PMICs
pwm: New driver to support PWMs on TWL4030/6030 series of PMICs
pwm: pwm-tiehrpwm: pinctrl support
pwm: tiehrpwm: Add device-tree binding
pwm: pwm-tiehrpwm: Adding TBCLK gating support.
pwm: pwm-tiecap: pinctrl support
pwm: tiecap: Add device-tree binding
pwm: Add TI PWM subsystem driver
pwm: Device tree support for PWM polarity
pwm: vt8500: Ensure PWM clock is enabled during pwm_config
pwm: vt8500: Fix build error
pwm: spear: Staticize spear_pwm_config()
pwm: Add SPEAr PWM chip driver support
...
The s3c->pwm_id is used to calculate offset of related register.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the duty-cycle and period passed in are not negative. This
should eventually be made implicit by making them unsigned. While at
it, the drivers' .config() implementations can have the equivalent
checks removed.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Jonghwan Choi <jhbird.choi@samsung.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: "Philip, Avinash" <avinashphilip@ti.com>
Cc: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
This patch adds missing device pointer to struct pwm_chip. If the
device pointer is NULL, pwmchip_add() will return error.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Move the driver to drivers/pwm/ and convert it to use the framework.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
[eric@eukrea.com: fix pwmchip_add return code test]
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
