Most machine files include "devices-imxXX.h" which in turn includes
<mach/devices-common.h>. The latter already includes many headers
that the machine files don't need to include again.
These were found by:
$ grep \#include arch/arm/plat-mxc/include/mach/devices-common.h > tmpfile
$ git grep -l 'devices-imx' arch/arm | xargs grep -f tmpfile -F
(but I kept linux/init.h, linux/kernel.h and linux/platform_device.h)
LAKML-Reference: 1298912674-15153-2-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As there is a mx53_smd board in the kernel, using SMD_FEC_PHY_RST as the pin name can be misleading when used
on a MX53_EVK board.
Change the pin name to reflect the board name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code inside mx53_evk_fec_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value right after. This is not needed.
By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On mx53_evk board only RX/TX pins are used on UART3.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix UART1 IOMUX settings and configure UART1 to work with only RX/TX pins.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This iomux file contains all the available pins that are iomux
capable.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
1. changes some register address to fit macro definition
2. add platform data and clock for sdhc
Signed-off-by: Yong Shen <yong.shen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
1. Adjust FEC base address name to fit macro definition
2. Add platform data and reset function for FEC
Signed-off-by: Yong Shen <yong.shen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
