Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
In order to use standard 'xdp' prefix, rename convert_to_xdp_frame
utility routine in xdp_convert_buff_to_frame and replace all the
occurrences
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/6344f739be0d1a08ab2b9607584c4d5478c8c083.1590698295.git.lorenzo@kernel.org
When setting the PHY cfg (CQ cmd 0x0601), if the firmware responds
with an EMODE error, software will ignore the error as it simply
means that manageability (ex: BMC) is in control of the link and that
the new setting may not be applied.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The logic was missing for adding back perfect flows after flow director
filter delete. The code now adds perfect flows into the HW tables after
filter delete.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VSI is built (i.e. reset, set channels, etc.)
the coalesce settings will be preserved in most cases. However, when the
number of q_vectors are increased the settings for the new q_vectors
will be set to the driver defaults of AIM on, Rx/Tx ITR 50, and INTRL 0.
This is causing issues with how the ethtool layer gets the current
coalesce settings since it only uses q_vector 0. So, assume that the user
set the coalesce settings globally (i.e. ethtool -C eth0) and use q_vector
0's settings for all of the new q_vectors.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ceb2f00707 ("ice: Use pci_get_dsn()") changed the code to
use a new function to get the Device Serial Number. It also changed
the case of the filename for loading a package on a specific NIC
from lowercase to uppercase. Change the filename back to
lowercase since that is what we specified.
Fixes: ceb2f00707 ("ice: Use pci_get_dsn()")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Where possible, cuddle multiple lines of function signatures to be
consistent throughout the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A VF driver has the ability to request reset via VIRTCHNL_OP_RESET_VF.
This is a required step in VF driver load. Currently, the PF is only
allowing a VF to request reset using this method after the VF has
already communicated resources via VIRTCHNL_OP_GET_VF_RESOURCES.
However, this is incorrect because the VF can request reset before
requesting resources. Fix this by allowing the VF to request a reset
once it has been initialized.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver prevents a user from doing
modprobe ice
ethtool -L eth0 combined 5
ip link set eth0 up
The ethtool command fails, because the driver is checking to see if the
interface is down before allowing the get_channels to proceed (even for
a set_channels).
Remove this check and allow the user to configure the interface
before bringing it up, which is a much better usability case.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Always clear the previous value in QRXFLXP_CNTXT before writing a new
value. This will make it so re-used queues will not accidentally take the
previously configured settings.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the PF is modifying the VF's port VLAN on the fly when
configured via iproute. This is okay for most cases, but if the VF
already has guest VLANs configured the PF has to remove all of those
filters so only VLAN tagged traffic that matches the port VLAN will
pass. Instead of adding functionality to track which guest VLANs have
been added, just reset the VF each time port VLAN parameters are
modified.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As currently, we are supporting only 5 PHY_SPEEDs for phy_type_high.
Thus, we should adjust the value of ICE_PHY_TYPE_HIGH_MAX_INDEX to 5.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To allow for resets during package download, increase the timeout period
after performing a PFR. The time waited is the global config lock
timeout plus the normal PFSWR timeout.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver does not recognize when there is an 802.1AD VLAN
tag right after the dmac/smac (outermost VLAN tag). If any DCB map is
applied and/or DCB is enabled this is causing the hardware to insert a
VLAN 0 tag after the 802.1AD VLAN tag that is already in the packet.
Fix this by preventing VLAN tag 0 from being added when any VLAN is
already present after dmac/smac (software offloaded) or skb (hardware
offloaded).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow untrusted VF to add 16 unicast/multicast filters. VF uses 1 filter
for the default/perm_addr/LAA MAC, 1 for broadcast, and 16 additional
unicast/multicast filters.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently a user is not allowed to clear a VF's administratively set MAC
on the PF. Fix this by allowing an all zero MAC address via "ip link set
${pf_eth} vf ${vf_id} mac 00:00:00:00:00:00".
An example use case for this would be issuing a "virsh shutdown"
command on a VM. The call to iproute mentioned above is part of this flow.
Without this change the driver incorrectly rejects clearing the VF's
administratively set MAC and prints unhelpful log messages.
Also, improve the comments surrounding this change.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-28
This series contains updates to the ice driver only.
Anirudh (Ani) adds a poll for reset completion before proceeding with
driver initialization when the DDP package fails to load and the firmware
issues a core reset.
Jake cleans up unnecessary code, since ice_set_dflt_vsi_ctx() performs a
memset to clear the info from the context structures. Fixed a potential
double free during probe unrolling after a failure. Also fixed a
potential NULL pointer dereference upon register_netdev() failure.
Tony makes two functions static which are not called outside of their
file.
Brett refactors the ice_ena_vf_mappings(), which was doing the VF's MSIx
and queue mapping in one function which was hard to digest. So create a
new function to handle the enabling MSIx mappings and another function
to handle the enabling of queue mappings. Simplify the code flow in
ice_sriov_configure(). Created a helper function for clearing
VPGEN_VFRTRIG register, as this needs to be done on reset to notify the
VF that we are done resetting it. Fixed the initialization/creation and
reset flows, which was unnecessarily complicated, so separate the two
flows into their own functions. Renamed VF initialization functions to
make it more clear what they do and why. Added functionality to set the
VF trust mode bit on reset. Added helper functions to rebuild the VLAN
and MAC configurations when resetting a VF. Refactored how the VF reset
is handled to prevent VF reset timeouts.
Paul cleaned up code not needed during a CORER/GLOBR reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Continuous Double "the" in a comment. Changed it to single "the"
Signed-off-by: Hari <harichandrakanthan@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet this register address
used by Host Transmit Discarded Packet by MAC counter
and not by not applicable Carrier Extension Error counter.
This patch comes to fix this wrong definition.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet sequence error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Receive error counter reflect total number of non-filtered
packets received with errors. This includes: CRC error,
symbol error, Rx data error and carrier extend error.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet symbol error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the following coccicheck warning:
drivers/net/ethernet/intel/i40e/i40e_adminq.c:699:13-21: Unneeded
variable: "ret_code". Return "0" on line 710
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's an error if the value of the RX/TX tail descriptor does not match
what was written. The error condition is true regardless the duration
of the interference from ME. But the driver only performs the reset if
E1000_ICH_FWSM_PCIM2PCI_COUNT (2000) iterations of 50us delay have
transpired. The extra condition can lead to inconsistency between the
state of hardware as expected by the driver.
Fix this by dropping the check for number of delay iterations.
While at it, also make __ew32_prepare() static as it's not used
anywhere else.
CC: stable <stable@vger.kernel.org>
Signed-off-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IGC supports a total of 32 rules. 16 MAC address based, 8 VLAN priority
based, and 8 Ethertype based. This patch fixes IGC_MAX_RXNFC_RULES
accordingly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The way Rx queue assignment based on mac address, Ethertype and VLAN
priority filtering operates in I225 doesn't allow us to properly support
NFC rules with multiple matches.
Consider the following example which assigns to queue 2 frames matching
the address MACADDR *and* Ethertype ETYPE.
$ ethtool -N eth0 flow-type ether dst <MACADDR> proto <ETYPE> queue 2
When such rule is applied, we have 2 unwanted behaviors:
1) Any frame matching MACADDR will be assigned to queue 2. It
doesn't matter the ETYPE value.
2) Any accepted frame that has Ethertype equals to ETYPE, no matter
the mac address, will be assigned to queue 2 as well.
In current code, multiple-match filters are accepted by the driver, even
though it doesn't support them properly. This patch adds a check for
multiple-match rules in igc_ethtool_is_nfc_rule_valid() so they are
rejected.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Transmit underrun, late and excess collision flags not in use.
This patch comes to clean up these flags.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function always return 0 now, we can make it return void to
simplify the code. This fixes the following coccicheck warning:
drivers/net/ethernet/intel/igb/e1000_mac.c:728:5-12: Unneeded variable:
"ret_val". Return "0" on line 751
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit b5f69ccf67 ("ixgbe: avoid bringing rings up/down as macvlans are added/removed")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the following coccicheck warning:
drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c:105:2-38: WARNING:
Assignment of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
No need to convert '==' expression to bool. This fixes the following
coccicheck warning:
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:68:11-16: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The comment above i40e_run_xdp_zc() was clearly copy-pasted from
function i40e_xsk_umem_setup, which is just above.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VF VSI calls ice_vsi_release() and ice_vsi_setup() it
subsequently clears/sets the VF cached variables for lan_vsi_idx and
lan_vsi_num. This works fine, but can be improved by handling this in
the VF specific VSI release and setup functions.
Also, when a VF VSI is setup too many parameters are passed that can be
derived from the VF. Fix this by only calling VF VSI setup with the bare
minimum parameters.
Also, add functionality to invalidate a VF's VSI when it's released
and/or setup fails. This will make it so a VF VSI cannot be accessed via
its cached vsi_idx/vsi_num in these cases.
Finally when a VF's VSI is invalidated set the lan_vsi_idx and
lan_vsi_num to ICE_NO_VSI to clearly show that there is no valid VSI
associated with this VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently VF VSI are being reset twice during a PFR or greater. This is
causing reset, specifically resetting all VFs, to take too long. This is
causing various issues with VF drivers not being able to gracefully
handle the VF reset timeout. Fix this by refactoring how VF reset is
handled for the case mentioned previously and for the VFR/VFLR case.
The refactor was done by doing the following:
1. Removing the call to ice_vsi_rebuild_by_type for
ICE_VSI_VF VSI, which was causing the initial VSI rebuild.
2. Adding functions for pre/post VSI rebuild functions that can be called
in both the reset all VFs case and reset individual VF case.
3. Adding VSI rebuild functions that are specific for the reset all VFs
case and adding functions that are specific for the reset individual
VF case.
4. Calling the pre-rebuild function, then the specific VSI rebuild
function based on the reset type, and then calling the post-rebuild
function to handle VF resets.
This patch series makes some assumptions about how VSI are handling by
FW during reset:
1. During a PFR or greater all VSI in FW will be cleared.
2. During a VFR/VFLR the VSI rebuild responsibility is in the hands of
the PF software.
3. There is code in the ice_reset_all_vfs() case to amortize operations
if possible. This was left intact.
4. PF software should not be replaying VSI based filters that were added
other than host configured, PF software configured, or the VF's
default/LAA MAC. This is the VF drivers job after it has been reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove VM/VF disable AQC (opcode 0x0C31) when resetting all VFs.
This is not required for CORER/GLOBR reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When resetting a VF the VLAN and MAC filter configurations need to be
replayed. Add helper functions for this purpose.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As the title says, use a function to set trust mode bit on reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some function names weren't very clear and some portions of VF creation
could be moved into functions for clarity. Fix this by renaming some
functions and move pieces of code into clearly name functions.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the same flow is used for VF VSI initialization/creation and VF
VSI reset. This makes the initialization/creation flow unnecessarily
complicated. Fix this by separating the initialization/creation of the
VF VSI from the reset flow.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Create a helper function for clearing VPGEN_VFRTRIG as this needs to be
done on reset to notify the VF that we are done resetting it. Also, it
needs to be done on SR-IOV initialization/creation in case it was left
in a bad state after SR-IOV tear down.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a new function for checking if SR-IOV can be configured based on
the PF and/or device's state/capabilities. Also, simplify the flow in
ice_sriov_configure().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ice_ena_vf_mappings() does all of the VF's MSIX and queue
mapping in one function. This makes it hard to digest. Fix this by
creating a new function for enabling MSIX mappings and one for enabling
queue mappings.
Also, rename some variables in the functions for clarity.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_get_pfa_module_tlv() and ice_read_sr_word() are not being called
outside of their file. Declare them as static.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If register_netdev() fails, the driver will attempt to cleanup the
q_vectors and inadvertently trigger a kernel BUG due to a NULL pointer
dereference.
This occurs because cleaning up q_vectors attempts to call
netif_napi_del on napi_structs which were never initialized.
Resolve this by releasing the netdev in ice_cfg_netdev and setting
vsi->netdev to NULL. This ensures that after ice_cfg_netdev fails the
state is rewound to match as if ice_cfg_netdev was never called.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ice_init_interrupt_scheme fails, ice_probe will jump to clearing up
the interrupts. This can lead to some static analysis tools such as the
compiler sanitizers complaining about double free problems.
Since ice_init_interrupt_scheme already unrolls internally on failure,
there is no need to call ice_clear_interrupt_scheme when it fails. Add
a new unroll label and use that instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove an unnecessary copy of vsi->info into ctxt->info in ice_vsi_init.
This line is essentially a no-op because ice_set_dflt_vsi_ctx performs
a memset to clear the info from the context structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are certain cases where the DDP load fails and the FW issues a
core reset. For these cases, wait for reset to complete before
proceeding with reset of the driver init.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a UMEM is present on a queue when an interface/queue pair is being
enabled, the driver will try to prepare the Rx buffers in advance to
improve performance. However, if fill queue is shorter than HW Rx ring,
the driver will report failure after getting the last address from the
fill queue.
This still lets the driver process the packets correctly during the NAPI
poll, but leads to a constant NAPI rescheduling. Not allocating the
buffers in advance would result in a potential performance decrease.
Commit d57d76428a ("xsk: Add API to check for available entries in FQ")
provides an API that lets drivers check the number of addresses that the
fill queue holds.
Notify the user if fill queue is not long enough to prepare all buffers
before packet processing starts, and allocate the buffers during the
NAPI poll. If the fill queue size is sufficient, prepare Rx buffers in
advance.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
