This patch changes the io operations so that they are out of line if
CONFIG_PPC_ISERIES is set and includes a firmware feature check in
that case.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update to the PowerPC PCI error recovery code.
Add code to enable MMIO if a device driver reports that it is capable
of recovering on its own. One anticipated use of this having a device
driver enable MMIO so that it can take a register dump, which might
then be followed by the device driver requesting a full reset.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add wrapper around the rtas call to enable MMIO or DMA on a frozen pci
slot.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up subroutine documentation; mostly formatting changes, with
some new content.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This corrects a pci_dev get/put imbalance that can occur only in
highly unlikely situations (kmalloc failures, pci devices with
overlapping resource addresses). No actual failures seen, this was
spotted during code review.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The stack frame address was being printed incorrectly in the backtrace
option of XMON on PPC. This patch fixes it to print the actual stack
address instead of the address of the local variable that contains it.
Signed-off-by: Josh Boyer <jdub@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Jakub noticed the cputable.c entry for Xilinx Virtex-4 FX was missing
a .platform value, so the AT_PLATFORM value wouldn't be set correctly.
This adds it.
Signed-off-by: Peter Bergner <bergner@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This abstracts the operations used in the bootwrapper, and defines
the operations needed for the bootwrapper to run on an OF platform.
The operations have been divided up into platform ops (platform_ops),
firmware ops (fw_ops), device tree ops (dt_ops), and console ops
(console_ops).
The proper operations will be hooked up at runtime to provide the
functionality that you need.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are various places where we want to extract an unsigned long
value from a device-tree property that can be 1 or 2 cells in length.
This replaces some open-coded calculations, and one place where we
assumed without checking that properties were the length we wanted,
with a little of_read_ulong() helper.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This produces essentially the same code and will make the iSeries i/o
consolidation easier.
The count parameter is changed to long since that will produce the same
(better) code on 32 and 64 bit builds.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
The io accessors insw_ns, outsw_ns, insl_ns and outsl_ns are unused
(except for one unnecessary use in drivers/net/3c509.c that is addressed
in a previous patch) and are only defined in powerpc/ppc, so remove them.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This fixes a compile error that only surfaces on CONFIG_SMP=n builds;
<asm/hvcall.h> seems to get pulled in through another header file for
SMP builds. This problem was introduced by the hvcall stats patch.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It seems that the occasional data corruption observed with the tg3
driver wasn't due to missing barriers after all, but rather seems to
be due to the DART (= IOMMU) in the U4 northbridge reading stale
IOMMU table entries from memory due to a race. This fixes it by
making the CPU read the entry back from memory before using it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the writeX family of functions to have a sync instruction
before the MMIO store rather than after, because the generally expected
behaviour is that the device receiving the MMIO store can be guaranteed
to see the effects of any preceding writes to normal memory.
To preserve ordering between writeX and readX, and to preserve ordering
between preceding stores and the readX, the readX family of functions
have had an sync added before the load.
Although writeX followed by spin_unlock is not officially guaranteed
to keep the writeX inside the spin-locked region unless an mmiowb()
is used, there are currently drivers that depend on the previous
behaviour on powerpc, which was that the mmiowb wasn't actually required.
Therefore we have a per-cpu flag that is set by writeX, cleared by
__raw_spin_lock and mmiowb, and tested by __raw_spin_unlock. If it is
set, __raw_spin_unlock does a sync and clears it.
This changes both 32-bit and 64-bit readX/writeX. 32-bit already has a
sync in __raw_spin_unlock (since lwsync doesn't exist on 32-bit), and thus
doesn't need the per-cpu flag.
Tested on G5 (PPC970) and POWER5.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Export copy_4K_page() for use by modules via copy_page() (such as
CacheFiles).
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xmon does not print a backtrace per default. This is bad on systems with
USB keyboard, the most needed info about the crash is lost.
print a backtrace during the very first xmon entry.
Booting with xmon=nobt disables the autobacktrace functionality.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the following whitespace warnings when compiling with ARCH=ppc
arch/ppc/Kconfig:1207:warning: leading whitespace ignored
arch/ppc/Kconfig:1226:warning: leading whitespace ignored
arch/ppc/Kconfig:1231:warning: leading whitespace ignored
Also fix a typo ("Supprt").
Signed-off-by: Josh Boyer <jdub@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add instrumentation for hypervisor calls on pseries. Call statistics
include number of calls, wall time and cpu cycles (if available) and
are made available via debugfs. Instrumentation code is behind the
HCALL_STATS config option and has no impact if not enabled.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Base patch for PA6T and PA6T-1682M. This introduces the
arch/powerpc/platform/pasemi directory, together with basic
implementations for various setup.
Much of this was based on other platform code, i.e. Maple, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reduce default cacheline size on 64-bit powerpc from 128 bytes to 64.
This is the architected minimum. In most cases we'll still end up using
cache line information from the device tree, but defaults are used during
early boot and doing a few dcbst/icbi's too many there won't do any harm.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch allows XMON to run on the 4xx platform. Tested on
Walnut, Ebony, and Nova (440GX based) eval boards. 440EP, 440SP, and
440SPE boards should work as well. Patch is against 2.6.18-rc6.
Signed-off-by: Josh Boyer <jdub@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow the pm_power_off function variable in PPC to work as an override.
This makes the function consistent with the other architectures and it
allows generic poweroff operations (like those provided in IPMI
systems) to work properly on PPC.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Joseph Barnett <jbarnett@motorola.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In an attempt to make it easier for a power5 optimized app to run on a
power4 or a 970 or random earlier machine, this provides emulation of
the popcntb instruction.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As part of the new irq code pseries_kexec_cpu_down() was split into a
xics and mpic version. The vpa unregister logic is now only done in the
xics routine, and although that's ok in practice (we don't have SPLPAR
machines with mpic), I'd rather have the two concepts stay separate.
So move the vpa unregister into pseries_kexec_cpu_down(), which gets called
by both the xics and mpic routines. This also gives us an obvious place to
put any new kexec-down logic needed in future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Call chip->eoi(irq) to clear any pending interrupt in case of kdump
shutdown sequence. chip->end(irq) does not serve this purpose.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update PReP defconfig, disable some drivers for hardware that is not
used on those systems; enable SL82C105 IDE driver for Powerstack.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'audit.b29' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] sparc64 audit syscall classes hookup
[PATCH] syscall class hookup for all normal targets
... that should do it for all targets; the only remaining issues are
mips (currently treated as non-biarch) and handling of other OS
emulations (OSF/SunOS/Solaris/???). The latter would need to be
assigned new AUDIT_ARCH_... ABI numbers anyway...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Take default arch/*/kernel/audit.c to lib/, have those with special
needs (== biarch) define AUDIT_ARCH in their Kconfig.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
sh64 wasn't providing a sensible pm_power_off(), add one,
and just wrap it to machine_power_off, which already does
the right thing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While we've been sorting out the toolchain fiasco, some of
the code has suffered a bit of bitrot. Building with GCC4
also brings up some more build warnings. Trivial fixes for
both issues.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The original sh64 toolchains required that we tune the ISA
level accordingly to not have head.S/entry.S blow up. With
current toolchains, this is no longer the case, and the
syntax magically changed as well, causing all current
toolchains to die a horrible death.
Incidentally, code generation in other parts of the kernel
is now significantly complex enough that none of the older
toolchains make it very far these days, so there's not
even any point in preserving legacy compatability via
as-option.
This fixes a long-standing issue, as noted here:
http://lkml.org/lkml/2005/1/5/223
Though at the time the current toolchains were too broken
to make adjusting the tuning worthwhile.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3778/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410 [simtec]
[ARM] 3783/1: S3C2412: fix IRQ_EINT0 to IRQ_EINT3 handling
[ARM] 3779/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410 [left]
[ARM] 3777/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410 [regs-*.h]
[ARM] 3776/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410
[ARM] 3775/1: S3C24XX: do not add same sysdev_driver to two classes
[ARM] 3774/1: S3C24XX: SMDK2413 has two machine IDs
[ARM] 3773/1: Add the HWCAP_VFP bit for the ARM926 CPUs
[ARM] 3772/1: Fix compilation error in mach-ixp4xx/nslu2*
[ARM] 3767/1: S3C24XX: remove changelog comments from arch/arm/mach-s3c2410
[ARM] 3766/1: Fix typo in ARM _raw_read_trylock
Patch from Ben Dooks
The IRQ_EINT0 through IRQ_EINT3 handling has changed
on the S3C2412 from the previous SoCs in the range,
and thus we need to add code to handle this.
The changes come about due to these IRQs being
displayed in two different registers, and needing to
be acked and masked in both.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The s3c244x-irq.c code makes the mistake of adding
the same drive to two different sys-classes. This
causes the class lists to become corrupted and the
suspend code to OOPS.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sn_cpu_init() is required for cpu initialization on SN platforms.
Change __init to __cpuinit so that the function is not freed with init code/data.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
