In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Loading then unloading wm97xx-ts.ko when CONFIG_AC97_BUS=m
causes a WARNING: from drivers/base/driver.c:
Unexpected driver unregister!
WARNING: CPU: 0 PID: 1709 at ../drivers/base/driver.c:193 driver_unregister+0x30/0x40
Fix this by only calling driver_unregister() with the same
condition that driver_register() is called.
Fixes: ae9d1b5fbd ("Input: wm97xx: add new AC97 bus support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some touchscreens, depending on the firmware and/or the digitizer, report
coordinates which never reach 0 along one or both of their axis.
This has been seen for example on the Silead touchscreens on a Onda V891w
and a Point of View mobii TAB-P800w(v2.0).
This commit adds support for touchscreen-min-x and touchscreen-min-y
device-properties which can be set to communicate the actual start
coordinates (rather then 0,0) to userspace.
This commit also drop the "(in pixels)" comment from the documentation
of the touchscreen-size-x and touchscreen-size-y properties. The comment
suggested that there is a relation between the range of reported
coordinates and the display resolution, which is only true for some
devices. The "(in pixels)" comment is replaced with "(maximum x coordinate
reported + 1)" to mirror the language describing the new touchscreen-min-x
and -min-y properties.
When set this fixes e.g. not being able to click things in the GNOME3
top-bar on the 2 example tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To avoid bounce buffer when an i2c controller decides to use DMA for a
transaction, let's make out buffer that we use for reads DMA-safe and let
the master know that DMAing into it is safe.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A certain silead controller (Chip ID: 0x56810000) loses its firmware
after suspend, causing the resume to fail. This patch tries to load
the firmware, should a resume error occur and retries the resuming.
Signed-off-by: Julian Sax <jsbc@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is how userspace checks for touchscreen devices most reliably.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Both v4.16-rc7 commit 93afb1d6e7 ("Input: atmel_mxt_ts - switch from
OF to generic device properties") and v4.16-rc7 commit 96a938aa21
("Input: atmel_mxt_ts - remove platform data support") added includes of
"<linux/property.h>". Remove one of the duplicate includes to fix this.
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds wakeup function support for egalax touch
screen, if "wakeup-source" is added to device tree's egalax
touch screen node, the wakeup function will be enabled, and
egalax touch screen will be able to wakeup system from suspend.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If T9.CTRL DISAMP is set, then pressure is reported as zero. This means
some app layers (eg tslib) will ignore the contact.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We use sscanf to parse the configuration file, so it's necessary to zero
terminate the configuration otherwise a truncated file can cause the
parser to run off into uninitialised memory.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On devices with the T71 object, the config CRC will start there, rather
than at T7.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver only registers one input device, which uses the screen
parameters from the first T9 instance. The first T63 instance also uses
those parameters.
It is incorrect to send input reports from the second instances of these
objects if they are enabled: the input scaling will be wrong and the
positions will be mashed together.
This also causes problems on Android if the number of slots exceeds 32.
In the future, this could be handled by looking for enabled touch object
instances and creating an input device for each one.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wdt87xx_resume() is never called in atomic context. It calls mdelay() to
busily wait, which is not necessary. mdelay() can be replaced with
msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I do not think Vojtech wants snail mail these days (and he mentioned that
nobody has ever sent him snail mail), and the address is not even valid
anymore, so let's remove snail-mail instructions from the sources.
Acked-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Keep the documentation link up-to-date in case anybody need to dive into it
again, and update email address while at it.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The only user of this driver in mainline does not make use of the module
parameters, so let's remove them. All properties for this driver should be
set through DT or pdata.
Use touchscreen_parse_properties() to automatically set some of the common
touchscreen properties and derive the axis inversion through that.
And finally, use touchscreen_report_pos() to handle the DT properties
automatically instead of doing the inversion ourselves.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Provide a match table so that the driver can be used in devicetree setups.
More properties are added in a later patch.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Silead touchscreen on the Chuwi Vi8 tablet uses MSSL0002 as ACPI HID,
rather then the usual MSSL1680 id.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
GPD Win 2 Website: http://www.gpd.hk/gpdwin2.asp
Tested on a unit from the first production run sent to Indiegogo backers
Signed-off-by: Ethan Lee <flibitijibibo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Prevent system suspend while user has finger on touch screen,
because TSC is wakeup source and suspending device while in use will
result in failure to disable the module.
This patch uses pm_stay_awake() and pm_relax() APIs to prevent and
resume system suspend as required.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is seen that just enabling the TSC module triggers a HW_PEN IRQ
without any interaction with touchscreen by user. This results in first
suspend/resume sequence to fail as system immediately wakes up from
suspend as soon as HW_PEN IRQ is enabled in suspend handler due to the
pending IRQ. Therefore clear all IRQs at probe and also in suspend
callback for sanity.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At the mentioned address there's nothing found. By searching information
on the controller chip still can be found, so update the link to the
resulting page.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current reset-gpio support triggers an interrupt storm on platforms
using the maxtouch with level based interrupt. The Motorola Droid 4,
which I used for some of the tests is not affected, since it uses a edge
based interrupt.
This change avoids the interrupt storm by enabling the device while its
interrupt is disabled. Afterwards we wait 100ms. This is important for
two reasons: The device is unresponsive for some time (~22ms for
mxt224E) and the CHG (interrupt) line is not working properly for 100ms.
We don't need to wait for any following interrupts, since the following
mxt_initialize() checks for bootloader mode anyways.
This fixes a boot issue on GE PPD (watchdog kills device due to
interrupt storm) and does not cause regression on Motorola Droid 4.
Fixes: f657b00df2 ("Input: atmel_mxt_ts - add support for reset line")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver needs help determining whether it is dealing with a touchscreen
or a touchpad, and with button mapping. Previously we supported passing
this data via device properties, and also had DMI lists for Chromebooks
that specified Atmel devices in ACPI, but did not provide enough data
there. Now that chromeos_laptop driver is adjusted to supply necessary
device properties even for ACPI devices, we can drop the DMI tables and
refuse to probe if device properties are not attached to the device.
We use presence of "compatible" property to determine if device properties
are attached to the device or not and rely on chromeos_laptop to re-probe
the device after attaching missing device properties to it.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlsB91MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGqLYH+gPrmb8gvH6CmckN
5U+RKRjzvs6oDqXf5yFUJ7NqW1Ex8qMuAqv1Kx2LpuN8sDD42fPB0A5OxijNgk81
omJIxqANbFPUQCt+epR1P5dp0XqbXCcIvmo9Dd2TM4EP0mcQqr+c61d7JXtVATMu
JrR5X7pgepatgH7JYI7fm1yIh/6RIhYZXjU2HxwiRHIzsLfW/sTmM4HZksv8nJjl
m+bT8XzEUCBhWCLT8z0TbbVug1N2qdyMzkMIS2JmDVJE4FZ9YOEnZzaCHGNZrkVV
OYzr94Bv2Z2PO3KIrsEsNA/szhr9/8f5Si9mk9nOi2kTuvaF9hhjKxcCozVB+ses
fm8wpmM=
=FiAO
-----END PGP SIGNATURE-----
Merge tag 'v4.17-rc6' into next
Sync up with mainline to bring in Atmel controller changes for Caroline.
Allow querying of the firmware revision of the device
example:
4.10
Tested on ZII RDU2 platform and on Intel x86_64 PC.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ChipOne icn8505 is an i2c capacitive touchscreen controller typically
used in cheap x86 tablets, this commit adds a driver for it.
Note the icn8505 is somewhat similar to the icn8318 and I started with
modifying that driver to support both, but in the end the differences were
too large and I decided to write a new driver instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Just a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - add missing compatible strings to OF device table
Input: atmel_mxt_ts - fix the firmware update
Input: atmel_mxt_ts - add touchpad button mapping for Samsung Chromebook Pro
MAINTAINERS: Rakesh Iyer can't be reached anymore
Input: hideep_ts - fix a typo in Kconfig
Input: alps - fix reporting pressure of v3 trackstick
Input: leds - fix out of bound access
Input: synaptics-rmi4 - fix an unchecked out of memory error path
Commit af503716ac ("i2c: core: report OF style module alias for devices
registered via OF") fixed how the I2C core reports the module alias when
devices are registered via OF.
But the atmel_mxt_ts driver only has an "atmel,maxtouch" compatible in its
OF device ID table, so if a Device Tree is using a different one, autoload
won't be working for the module (the matching works because the I2C device
ID table is used as a fallback).
So add compatible strings for each of the entries in the I2C device table.
Fixes: af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[dtor: document which compatibles are deprecated and should not be used]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The automatic update mechanism will trigger an update if the
info block CRCs are different between maxtouch configuration
file (maxtouch.cfg) and chip.
The driver compared the CRCs without retrieving the chip CRC,
resulting always in a failure and firmware flashing action
triggered. Fix this issue by retrieving the chip info block
CRC before the check.
Note that this solution has the benefit that by reading the
information block and the object table into a contiguous region
of memory, we can verify the checksum at probe time. This means
we make sure that we are indeed talking to a chip that supports
object protocol correctly.
Using this patch on a kevin chromebook, the touchscreen and
touchpad drivers are able to match the CRC:
atmel_mxt_ts 3-004b: Family: 164 Variant: 14 Firmware V2.3.AA Objects: 40
atmel_mxt_ts 5-004a: Family: 164 Variant: 17 Firmware V2.0.AA Objects: 31
atmel_mxt_ts 3-004b: Resetting device
atmel_mxt_ts 5-004a: Resetting device
atmel_mxt_ts 3-004b: Config CRC 0x573E89: OK
atmel_mxt_ts 3-004b: Touchscreen size X4095Y2729
input: Atmel maXTouch Touchscreen as /devices/platform/ff130000.i2c/i2c-3/3-004b/input/input5
atmel_mxt_ts 5-004a: Config CRC 0x0AF6BA: OK
atmel_mxt_ts 5-004a: Touchscreen size X1920Y1080
input: Atmel maXTouch Touchpad as /devices/platform/ff140000.i2c/i2c-5/5-004a/input/input6
Signed-off-by: Nick Dyer <nick.dyer@shmanahar.org>
Acked-by: Benson Leung <bleung@chromium.org>
[Ezequiel: minor patch massage]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds the correct platform data information for the Caroline
Chromebook, so that the mouse button does not get stuck in pressed state
after the first click.
The Samus button keymap and platform data definition are the correct
ones for Caroline, so they have been reused here.
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Salvatore Bellizzi <lkml@seppia.net>
Tested-by: Guenter Roeck <groeck@chromium.org>
Cc: stable@vger.kernel.org
[dtor: adjusted vendor spelling to match shipping firmware]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a spelling error found in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Incorporates a series from Dmitry to remove platform data from
chromeos_laptop.c, which was the only user of platform data
for the atmel_mxt_ts driver.
Includes a series to clean up sysfs and debugfs for cros_ec.
Other misc. cleanups.
Thanks,
Benson
-----BEGIN PGP SIGNATURE-----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=mDkk
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- a series from Dmitry to remove platform data from chromeos_laptop.c,
which was the only user of platform data for the atmel_mxt_ts driver.
- a series to clean up sysfs and debugfs for cros_ec
- other misc cleanups
* tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform: (22 commits)
platform/chrome: mfd/cros_ec_dev: Add sysfs entry to set keyboard wake lid angle
platform/chrome: cros_ec_debugfs: Add PD port info to debugfs
platform/chrome: cros_ec_debugfs: Use octal permissions '0444'
platform/chrome: cros_ec_sysfs: use permission-specific DEVICE_ATTR variants
platform/chrome: cros_ec_sysfs: introduce to_cros_ec_dev define.
platform/chrome: cros_ec_sysfs: Modify error handling
platform/chrome: cros_ec_lpc: Add support for Google devices using custom coreboot firmware
platform/chrome: cros_ec_lpc: wake up from s2idle on Chrome EC
Input: atmel_mxt_ts - remove platform data support
platform/chrome: chromeos_laptop - discard data for unneeded boards
platform/chrome: chromeos_laptop - use device properties for Pixel
platform/chrome: chromeos_laptop - rely on I2C to set up interrupt trigger
platform/chrome: chromeos_laptop - use I2C notifier to create devices
platform/chrome: chromeos_laptop - parse DMI IRQ data once
platform/chrome: chromeos_laptop - rework i2c peripherals initialization
platform/chrome: chromeos_laptop - factor out getting IRQ from DMI
platform/chrome: chromeos_laptop - introduce pr_fmt()
platform/chrome: chromeos_laptop - stop setting suspend mode for Atmel devices
platform/chrome: chromeos_laptop - add SPDX identifier
Input: atmel_mxt_ts - switch ChromeOS ACPI devices to generic props
...
Now that there are no users of custom Atmel platform data, and everyone
has switched to the generic device properties, we can remove support for
the platform data.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Move older ChromeOS devices describing Atmel controllers in ACPI, but not
providing enough details to configure the controllers properly, from
platform data over to generic device properties. This will allow us
remove support for platform data later on, leaving only generic device
properties in place.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Instead of using OF-specific APIs to fecth device properties, let's switch
to generic device properties API. This will allow us to use device
properties on legacy ChromeOS devices and get rid of platform data down
the road.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
