After a number of suspend and resume cycles, it is possible for the RBUF
to be stuck in Wake-on-LAN mode, despite the MPD enable bit being
cleared which instructed the RBUF to exit that mode.
Avoid creating that problematic condition by clearing the RX_EN and
TX_EN bits in the UniMAC prior to disable the Magic Packet Detector
logic which is guaranteed to make the RBUF exit Wake-on-LAN mode.
Fixes: 83e82f4c70 ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Use after free in rxrpc_put_local(), from David Howells.
2) Fix 64-bit division error in mlxsw, from Nathan Chancellor.
3) Make sure we clear various bits of TCP state in response to
tcp_disconnect(). From Eric Dumazet.
4) Fix netlink attribute policy in cls_rsvp, from Eric Dumazet.
5) txtimer must be deleted in stmmac suspend(), from Nicolin Chen.
6) Fix TC queue mapping in bnxt_en driver, from Michael Chan.
7) Various netdevsim fixes from Taehee Yoo (use of uninitialized data,
snapshot panics, stack out of bounds, etc.)
8) cls_tcindex changes hash table size after allocating the table, fix
from Cong Wang.
9) Fix regression in the enforcement of session ID uniqueness in l2tp.
We only have to enforce uniqueness for IP based tunnels not UDP
ones. From Ridge Kennedy.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits)
gtp: use __GFP_NOWARN to avoid memalloc warning
l2tp: Allow duplicate session creation with UDP
r8152: Add MAC passthrough support to new device
net_sched: fix an OOB access in cls_tcindex
qed: Remove set but not used variable 'p_link'
tc-testing: add missing 'nsPlugin' to basic.json
tc-testing: fix eBPF tests failure on linux fresh clones
net: hsr: fix possible NULL deref in hsr_handle_frame()
netdevsim: remove unused sdev code
netdevsim: use __GFP_NOWARN to avoid memalloc warning
netdevsim: use IS_ERR instead of IS_ERR_OR_NULL for debugfs
netdevsim: fix stack-out-of-bounds in nsim_dev_debugfs_init()
netdevsim: fix panic in nsim_dev_take_snapshot_write()
netdevsim: disable devlink reload when resources are being used
netdevsim: fix using uninitialized resources
bnxt_en: Fix TC queue mapping.
bnxt_en: Fix logic that disables Bus Master during firmware reset.
bnxt_en: Fix RDMA driver failure with SRIOV after firmware reset.
bnxt_en: Refactor logic to re-enable SRIOV after firmware reset detected.
net: stmmac: Delete txtimer in suspend()
...
The driver currently only calls netdev_set_tc_queue when the number of
TCs is greater than 1. Instead, the comparison should be greater than
or equal to 1. Even with 1 TC, we need to set the queue mapping.
This bug can cause warnings when the number of TCs is changed back to 1.
Fixes: 7809592d3e ("bnxt_en: Enable MSIX early in bnxt_init_one().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current logic that calls pci_disable_device() in __bnxt_close_nic()
during firmware reset is flawed. If firmware is still alive, we're
disabling the device too early, causing some firmware commands to
not reach the firmware.
Fix it by moving the logic to bnxt_reset_close(). If firmware is
in fatal condition, we call pci_disable_device() before we free
any of the rings to prevent DMA corruption of the freed rings. If
firmware is still alive, we call pci_disable_device() after the
last firmware message has been sent.
Fixes: 3bc7d4a352 ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_ulp_start() needs to be called before SRIOV is re-enabled after
firmware reset. Re-enabling SRIOV may consume all the resources and
may cause the RDMA driver to fail to get MSIX and other resources.
Fix it by calling bnxt_ulp_start() first before calling
bnxt_reenable_sriov().
We re-arrange the logic so that we call bnxt_ulp_start() and
bnxt_reenable_sriov() in proper sequence in bnxt_fw_reset_task() and
bnxt_open(). The former is the normal coordinated firmware reset sequence
and the latter is firmware reset while the function is down. This new
logic is now more straight forward and will now fix both scenarios.
Fixes: f3a6d206c2 ("bnxt_en: Call bnxt_ulp_stop()/bnxt_ulp_start() during error recovery.")
Reported-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Put the current logic in bnxt_open() to re-enable SRIOV after detecting
firmware reset into a new function bnxt_reenable_sriov(). This call
needs to be invoked in the firmware reset path also in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are users already and will be more of BITS_TO_BYTES() macro. Move
it to bitops.h for wider use.
In the case of ocfs2 the replacement is identical.
As for bnx2x, there are two places where floor version is used. In the
first case to calculate the amount of structures that can fit one memory
page. In this case obviously the ceiling variant is correct and
original code might have a potential bug, if amount of bits % 8 is not
0. In the second case the macro is used to calculate bytes transmitted
in one microsecond. This will work for all speeds which is multiply of
1Gbps without any change, for the rest new code will give ceiling value,
for instance 100Mbps will give 13 bytes, while old code gives 12 bytes
and the arithmetically correct one is 12.5 bytes. Further the value is
used to setup timer threshold which in any case has its own margins due
to certain resolution. I don't see here an issue with slightly shifting
thresholds for low speed connections, the card is supposed to utilize
highest available rate, which is usually 10Gbps.
Link: http://lkml.kernel.org/r/20200108121316.22411-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----
iQI/BAABCgApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAl4vKHwLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYMPGBAAuVNUZaZfWYHpiVP2oRcUQUguFiD3NTbknsyzV2oH
J9P0GfeENSKwE9OOhZ7XIjnCZAJwQgTK/ppQY5yiQ/KAtYyyXjXEJ6jqqjiTDInr
+3+I3t/LhkgrK7tMrb7ylTGa/d7KhaciljnOXC8+b75iddvM9I1z2pbHDbppZMS9
wT4RXL/cFtRb85AfOyPLybcka3f5P2gGvQz38qyimhJYEzHDXZu9VO1Bd20f8+Xf
eLBKX0o6yWMhcaPLma8tm0M0zaXHEfLHUKLSOkiOk+eHTWBZ3b/w5nsOQZYZ7uQp
25yaClbameAn7k5dHajduLGEJv//ZjLRWcN3HJWJ5vzO111aHhswpE7JgTZJSVWI
ggCVkytD3ESXapvswmACSeCIDMmiJMzvn6JvwuSMVB7a6e5mcqTuGo/FN+DrBF/R
IP+/gY/T7zIIOaljhQVkiEIIwiD/akYo0V9fheHTBnqcKEDTHV4WjKbeF6aCwcO+
b8inHyXZSKSMG//UlDuN84/KH/o1l62oKaB1uDIYrrL8JVyjAxctWt3GOt5KgSFq
wVz1lMw4kIvWtC/Sy2H4oB+RtODLp6yJDqmvmPkeJwKDUcd/1JKf0KsZ8j3FpGei
/rEkBEss0KBKyFAgBSRO2jIpdj2epgcBcsdB/r5mlhcn8L77AS6mHbA173kY4pQ/
Kdg=
=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Display the following information via devlink info command:
- Driver name
- Board id
- Broad revision
- Board Serial number
- Board FW version
- FW parameter set version
- FW App version
- FW management version
- FW RoCE version
Standard output example:
$ devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver bnxt_en
serial_number 00-10-18-FF-FE-AD-05-00
versions:
fixed:
asic.id D802
asic.rev 1
running:
fw 216.1.124.0
fw.psid 0.0.0
fw.app 216.1.122.0
fw.mgmt 864.0.32.0
fw.roce 216.1.15.0
[ This version has incorporated changes suggested by Jakub Kicinski to
use generic devlink version tags. ]
v2: Use fw.psid
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of switch_id, renaming it to dsn will be more meaningful
so that it can be used to display device serial number in follow up
patch via devlink_info command.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds status notification to devlink flash update
while flashing is in progress.
$ devlink dev flash pci/0000:05:00.0 file 103.pkg
Preparing to flash
Flashing done
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest kernels get the phys_port_name via devlink, if
ndo_get_phys_port_name is not defined. To provide the phys_port_name
correctly, register devlink before registering netdev.
Also call devlink_port_type_eth_set() after registering netdev as
devlink port updates the netdev structure and notifies user.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow to register for devlink port and use port features.
Also register params only if firmware spec version is at least 0x10600
which will support reading/setting numbered variables in NVRAM.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define bnxt_dl_params_register() and bnxt_dl_params_unregister()
functions and move params register/unregister code to these newly
defined functions. This patch is in preparation to register
devlink irrespective of firmware spec. version in the next patch.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware bug has been fixed on B0 and newer chips, so disable the
workaround on these chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the only time we check and remove expired filters is
when we are inserting new filters.
Improving the aRFS expiry handling by adding code to do the above
work periodically.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_rx_flow_steer(), if the dissected packet is a fragment, do not
proceed to create the ntuple filter and return error instead. Otherwise
we would create a filter with 0 source and destination ports because
the dissected ports would not be available for fragments.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
575XX (P5) chips have the same UDP RSS hashing capability as P4 chips,
so we can enable it on P5 chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_port is meant to distinguish the network ports belonging to
the same PCI function. Our devices only have one network port
associated with each PCI function and so we should not set it for
correctness.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the 2nd parameter fw_dflt is not set, we are calling bnxt_probe_phy()
after the firmware has reset. There is no need to query the current
PHY settings from firmware as these settings may be different from
the ethtool settings that the driver will re-establish later. So
return earlier in bnxt_probe_phy() to save one firmware call.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_update_phy_setting(), ethtool_get_link_ksettings() and
bnxt_disable_an_for_lpbk(), we inconsistently use netif_carrier_ok()
to determine link. Instead, we should use bp->link_info.link_up
which has the true link state. The netif_carrier state may be off
during self-test and while the device is being reset and may not always
reflect the true link state.
By always using bp->link_info.link_up, the code is now more
consistent and more correct. Some unnecessary link toggles are
now prevented with this patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 7587935cfa ("net: bcmgenet: move NAPI initialization to
ring initialization") moved the code, this used to be
netif_tx_napi_add(), but we lost that small semantic change in the
process, restore that.
Fixes: 7587935cfa ("net: bcmgenet: move NAPI initialization to ring initialization")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSN read can fail, for example on a kdump kernel without PCIe extended
config space support. If DSN read fails, don't set the
BNXT_FLAG_DSN_VALID flag and continue loading. Check the flag
to see if the stored DSN is valid before using it. Only VF reps
creation should fail without valid DSN.
Fixes: 03213a9965 ("bnxt: move bp->switch_id initialization to PF probe")
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NTUPLE related firmware commands are sent to the wrong firmware
channel, causing all these commands to fail on new firmware that
supports the new firmware channel. Fix it by excluding the 3
NTUPLE firmware commands from the list for the new firmware channel.
Fixes: 760b6d3341 ("bnxt_en: Add support for 2nd firmware message channel.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would not be transmitting using the correct SYSTEMPORT transmit queue
during ndo_select_queue() which looks up the internal TX ring map
because while establishing the mapping we would be off by 4, so for
instance, when we populate switch port mappings we would be doing:
switch port 0, queue 0 -> ring index #0
switch port 0, queue 1 -> ring index #1
...
switch port 0, queue 3 -> ring index #3
switch port 1, queue 0 -> ring index #8 (4 + 4 * 1)
...
instead of using ring index #4. This would cause our ndo_select_queue()
to use the fallback queue mechanism which would pick up an incorrect
ring for that switch port. Fix this by using the correct switch queue
number instead of SYSTEMPORT queue number.
Fixes: 25c4407046 ("net: systemport: Simplify queue mapping logic")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in XDP mode, pages come from the page pool, and should
be freed back to the same pool or specifically detached. Currently,
when the driver re-initializes, the page pool destruction is delayed
forever since it thinks there are oustanding pages.
Fixes: 322b87ca55 ("bnxt_en: add page_pool support")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
Return EINPROGRESS to devlink health reporter recover as we are not yet
done and call devlink_health_reporter_recovery_done once reset is
successfully completed from workqueue context.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a straight-forward conversion case for the new function, and
while we're at it, we can remove a null write to skb->next by replacing
it with skb_mark_not_on_list.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Atomic operations that span cache lines are super-expensive on x86
(not just to the current processor, but also to other processes as all
memory operations are blocked until the operation completes). Upcoming
x86 processors have a switch to cause such operations to generate a #AC
trap. It is expected that some real time systems will enable this mode
in BIOS.
In preparation for this, it is necessary to fix code that may execute
atomic instructions with operands that cross cachelines because the #AC
trap will crash the kernel.
Since "pwol_mask" is local and never exposed to concurrency, there is
no need to set bits in pwol_mask using atomic operations.
Directly operate on the byte which contains the bit instead of using
__set_bit() to avoid any big endian concern due to type cast to
unsigned long in __set_bit().
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing max vlan configuration on the PF, firmware gets
assert as driver was configuring number of vlans more than what
is supported per port/engine, it was figured out that there is an
implicit vlan (hidden default vlan consuming hardware cam entry resource)
which is configured default for all the clients (PF/VFs) on client_init
ramrod by the adapter implicitly, so when allocating resources among the
PFs this implicit vlan should be considered or total vlan entries should
be reduced by one to accommodate that default/implicit vlan entry.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although it has same value as MAX_MAC_CREDIT_E2,
use MAX_VLAN_CREDIT_E2 appropriately.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1588 standard defines one step operation for both Sync and
PDelay_Resp messages. Up until now, hardware with P2P one step has
been rare, and kernel support was lacking. This patch adds support of
the mode in anticipation of new hardware developments.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When inserting the TSB, keep track of how many times we had to do
it and if there was a failure in doing so, this helps profile the
driver for possibly incorrect headroom settings.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During bcmgenet_put_tx_csum() make sure we differentiate a SKB
headroom re-allocation failure from the normal swap and replace
path.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can turn on the RX/TX checksum offloads and the scatter/gather
features by default and make sure that those are properly reflected
back to e.g: stacked devices such as VLAN.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver resume and open, the HW may have lost its context/state,
utilize bcmgenet_set_features() to make sure we do restore the correct
set of features that were previously configured.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally enabling TX and RX checksum
offloads, refactor bcmgenet_set_features() a bit such that
__netdev_update_features() during register_netdev() can make sure
that features are correctly programmed during network device
registration.
Since we can now be called during register_netdev() with clocks
gated, we need to temporarily turn them on/off in order to have a
successful register programming.
We also move the CRC forward setting read into
bcmgenet_set_features() since priv->crc_fwd_en matters while
turning on RX checksum offload, that way we are guaranteed they
are in sync in case we ever add support for NETIF_F_RXFCS at some
point in the future.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit updates the Rx checksum offload behavior of the driver
to use the more generic CHECKSUM_COMPLETE method that supports all
protocols over the CHECKSUM_UNNECESSARY method that only applies
to some protocols known by the hardware.
This behavior is perceived to be superior.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GENET hardware should be capable of generating IP checksums
using the NETIF_F_HW_CSUM feature, so switch to using that feature
instead of the depricated NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit configures the DMA masks for the GENET driver and
sets the NETIF_F_HIGHDMA flag to report support of the feature.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT is capabable of doing up to 40-bit of physical addresses, set
an appropriate DMA mask to permit that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
