This patch enables to use thermal-zone on r8a7791.
This thermal sensor can measure temperature from -40000 to 125000,
but over 117000 can be critical on this chip.
Thus, default critical temperature is now set as 115000 (this driver
is using 5000 steps) (Current critical temperature is using it as
90000, but there is no big reason about it)
And it doesn't check thermal zone periodically (same as current
behavior). You can exchange it by modifying polling-delay[-passive]
property.
You can set trip temp if your kernel has CONFIG_THERMAL_WRITABLE_TRIPS,
but you need to take care to use it, since it will call
orderly_poweroff() it it reaches to the value.
echo $temp > /sys/class/thermal/thermal_zone0/trip_point_0_temp
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK.
The presence of the SCIF_CLK crystal and its clock frequency depends on
the actual board.
Add the two optional clock sources (ZS_CLK and SCIF_CLK for the internal
resp. external clock) for the Baud Rate Generator for External Clock
(BRG) to all SCIF and HSCIF device nodes.
This increases the range and accuracy of supported baud rates on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use GIC_* defines for GIC interrupt cells in r8a7791 device tree.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7791 part of the EtherAVB device node.
Based on the commit f25d6b9772 ("ARM: shmobile: r8a7790: add EtherAVB DT
support").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the EtherAVB clock to the R8A7791 device tree.
Based on the commit 63d2d750c9 ("ARM: shmobile: r8a7790: add EtherAVB
clocks").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit a1bc260bb5 ("gpio: clean up gpio-ranges documentation")
declares the above property deprecated. That was more than 2 years ago.
Remove it, so it doesn't get copied around needlessly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7791 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Merging in the few patches I had kept separate from main next/dt, since others
got merged here directly.
* next/arm64:
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
arm64: dts: mt8173: Add clocks for SCPSYS unit
arm64: dts: mt8173: Add subsystem clock controller device nodes
+ Linux 4.3-rc5
On R8A7791, GPIO banks 1 and 7 are missing pins 26 to 31. Correct the
"gpio-ranges" properties of the GPIO1 node (GPIO7 is already correct).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car M2-W does not have an IMP core or an IMP clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
797a0626e0 ("ARM: shmobile: r8a7791 dtsi: Add CPG/MSTP Clock Domain")
added CPG/MSTP clock-cells domain support, but it was missing sound
support. This patch adds it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms: updated commit id referred to in changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add an appropriate "#power-domain-cells" property to the cpg_clocks
device node, to create the CPG/MSTP Clock Domain.
Add "power-domains" properties to all device nodes for devices that are
part of the CPG/MSTP Clock Domain and can be power-managed through an
MSTP clock. This applies to most on-SoC devices, which have a
one-to-one mapping from SoC device to DT device node. Notable
exceptions are the "display" and "sound" nodes, which represent multiple
SoC devices, each having their own MSTP clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch contains device tree node definition for JPEG codec peripheral
found in the Renesas R-Car r8a7791 SoC.
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the R-Car Gen2 GIC is assumed to be a GIC-400.
This has been confirmed by reading the GICD_IIDR register, which reports
0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds DMA properties to the HSUSB node.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the external IRQ controller irqc0 to the IRQC module clock, so it
can be power managed using that clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MSIOF Base Address H'E6xx can be accessed by CPU and DMAC.
MSIOF Base Address H'E7xx for DMAC was removed from H/W manual.
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Audio DMAC peri peri is no longer DMAEngine. it is supported by
sound driver. this patch enable it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7791 SDHI ch0/ch1 has SD_DMACR which is located in 0x324.
This patch updates register size
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add references to the transmit and receive DMA channels in the three
SDHI nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the ADSP clocks to the CPG and MSTP5 nodes of the R8A7791 device tree.
Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7791 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin. Describe those clocks in the device
tree, along with the USB_EXTAL clock from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.
Fixes: 59e79895b9 ("ARM: shmobile: r8a7791: Add clocks")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the seven IPMMU instances found in the r8a7791 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Tidy up #sound-dai-cells settings
* Drop "renesas,rcar_sound" compatible value
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VWG8
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-cleanups2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Cleanups for v3.20" from Simon
Horman:
Second Round of Renesas ARM Based SoC DT Cleanups for v3.20
* Tidy up #sound-dai-cells settings
* Drop "renesas,rcar_sound" compatible value
* tag 'renesas-dt-cleanups2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7790: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7791 dtsi: Drop "renesas,rcar_sound" compatible value
ARM: shmobile: r8a7790 dtsi: Drop "renesas,rcar_sound" compatible value
Signed-off-by: Olof Johansson <olof@lixom.net>
I made a mistake when rebasing Andrey Gusakov's patch adding MLB+ clock to the
R8A7791 device tree, inserting <&hp_clk> into the "clocks" property of the
MSTP8 node at a wrong position, so that the input clocks for MLB+ and IPMMU-SGX
got swapped...
Fixes: 7408d3061d ("ARM: shmobile: r8a7791: add MLB+ clock")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Renesas sound driver needs #sound-dai-cells settings, but, this usage
is a little bit confusable. It came from ALSA SoC historical reasons.
The sound DAI naming method is different between Single/Multi DAI in
the ALSA framework, and it is used for sound card matching.
And this #sound-dai-cells has relationship to it.
Current SoC dtsi has #sound-dai-cells = <1> as default settings
(= it is assuming that board/platform has multi DAI), and
board/platform side needs to overwrite it if board/platform was single
DAI. This style is more confusable for users.
This patch removes SoC side default settings, and force to set it by
board/platform side.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
