The PCIe host driver and the chip common initialisation accesses the
sprom struct, but it is not initialized when these functions are run.
Move the sprom parsing up in to do it earlier.
As we need the chip common core rev and some other attributes from the
chip common core, the early initialization is done before accessing the
sprom.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some parts of the initialization for chip common and the pcie core are
accessing the sprom struct, but it is not initialized at that stage.
Just do the necessary thing in the early register on SoCs and not the
complete initialization to read out the nvram from the flash chip.
After it is possible to read out the nvram, the sprom should be parsed
from it and the full initialization of the cores should be run.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cores are unregistered, entries
need to be removed from cores list in a safe manner.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_scan_bus allocates a bcma_core for each core found on the bus, but the
memory for cores handled by the bcma driver itself was not being freed when
the bus was unregistered. This patch adds special handling for the PCIE,
MIPS, and GBIT COMMON cores, to ensure that their memory allocation is
freed as well.
Note that this patch doesn't address the memory allocated for the CC core,
as that was corrected in my previous patch "bcma: register cc core driver,
device."
Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Saul St. John <saul.stjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions and structs are not used in an other file and the
prototypes are in no header file, just make them static so the compiler
is able to optimize them better.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit b9562545ef ("bcma: complete workaround for BCMA43224 and
BCM4313") introduced the wrong masks for setting the chip control
registers - the "mask" parameter is inverse.
It should be the mask of bits *not* changed, which is admittedly a bit
non-intuitive.
The incorrect mask not only causes the driver to not work correctly on
the chips affected (eg the BCM43224 on the Macbook Air 4,2) but the
state persists over a soft reset, causing the next boot to not
necessarily see the device correctly.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Arend Van Spriel <arend@broadcom.com>
Cc: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Cc: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This should fix the problem reported by Fengguang:
The coccinelle static checker emits these warnings:
drivers/bcma/scan.c:466:3-9: ERROR: missing iounmap; ioremap on line 451 and execution via conditional on line 465
drivers/bcma/scan.c:540:3-9: ERROR: missing iounmap; ioremap on line 515 and execution via conditional on line 539
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wrong interrupts where assigned to the cores in
bcma_core_mips_init(). This caused at least my serial console not to
response to any input.
This was caused by this patch which changed the order of the cores in
the list:
commit c334e25c9f
Author: Rafał Miłecki <zajec5@gmail.com>
Date: Wed Jul 11 12:37:00 2012 +0200
bcma: add new cores at the end of list
This should be fixed properly later so that the correct interrupt
numbers are assigned to the cores independently from the ordering of
the list. This patch restores the old behavior again. I will look into
the problem more deeply later.
I also changed the order of the list with the cores and their assigned
interrupt number which gets printed to the log. Now they are printed in
the same order like all the other lists of cores and like it was done
before the patch which changed the order.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes order in list more natural and fixes core->core_unit for more
than 2 cores.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GMAC COMMON core is present on BCM4706 and is used for example to access
board PHYs (PHYs can not be accessed directly using GBIT MAC core).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having bus number printed makes it much easier to anaylze logs on
systems with more buses. For example Netgear WNDR4500 has 3 AMBA buses
in total, which makes standard log really messy.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is needed by brcmsmac. This code is based on code from
the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The list of devices where nothing has to be done in
bcma_pmu_resources_init() and bcma_pmu_workarounds() is longer as all
the SoCs are missing there and some new devices will be added in some
time later. This patch changes the default case to just log on debug
level and also let the other devices which do not need any special
handling into the default case, instead of adding the missing 8 SoC
chip ids.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These functions are doing nothing in the current code.
I do not think we will need these function in the future as the
corresponding functions in the Broadcom SDK are just doing something
useful on chips supported by ssb or fullmac chips.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on the Broadcom SDK and brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ID was found on the PCIe wireless card on the board of a Netgear
WNDR3400 using a bcm4716. The device with this ID is identified by b43
as "Broadcom 43224 WLAN".
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is not core id with 0x4329, but at the same place in the open
source part of the Broadcom SDK is a check for some device with the
chip id of 0x4329. The device with a chip id of 0x4329 is a full mac
device, so it will never be supported by bcma, this part is running in
the firmware of the device and not on the host CPU.
This code is wrong and will never be used, so just remove it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip IDs are used all over bcma and no constants where defined.
This patch adds the constants and makes bcma use them.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on a recent version of the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of them are BCM4706 specific AFAWK. Most of them was confirmed on
Netgear WNDR450.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pc could be null if hosttype != BCMA_HOSTTYPE_PCI.
If we are on a device without a pci core this function is called with
pc = null by b43 and brcmsmac. If the host type is PCI we have a pci
core as well and pc can not be null.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MacBook Pro models with BCM4331 wireless have been found to have the ext
PA lines disabled after resuming from S3 without external power attach.
This causes them to be unable to transmit. Add a workaround to ensure
that the ext PA lines are enabled on BCM4331. Also extend all handling
of ext PA line muxing to BCM43431 as is done in the Broadcom SDK.
BugLink: http://bugs.launchpad.net/bugs/925577
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
Adds a missing read to flush the previous write (per the Broadcom SDK).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing __devexit attribute to bcma_host_pci_remove.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify ioremap_nocache calls to reflect the number of bytes read/written.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI Memory Resource start address and size are variable, dependent on
the H/W configuration. Modify the computation of io_map_base to use the
computed values.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_device_name only provides names for Broadcom cores. Modify logic to
provide names for MIPS and ARM cores as well.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on code from pcie_misc_config_fixup() in brcmsmac.
This patch is part of the move of pci specific code from brcmsmac to
bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on code from pcicore_fixcfg() in brcmsmac. This
patch is part of the move of pci specific code from brcmsmac to bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on code from pcie_extendL1timer() in brcmsmac. This
patch is part of the move of pci specific code from brcmsmac to bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on code from _ai_clkctl_cc() in brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These newly added attributes are used by brcmsmac. Now bcma should
parse all attributes used by brcmsmac out of the sprom.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is copied from the ssb sprom read code. These attributes are
partly used by b43 and brcmsmac and should also be read out on bcma
based devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The attribute country_code and alpha2 are two different attributes in
the sprom. country_code contains some code in an 8 bit coding and
alpha2 contains two chars with the country code. The attributes where
read out wrongly in the past and country_code is only available on
sprom version 1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This struct contains information about the board, the chip is running
on. The struct is filled for PCIe devices and SoCs. This information is
used by b43 and will be used by brcmsmac soon.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This resolves the conflict in:
drivers/usb/host/ehci-fsl.c
And picks up loads of xhci bugfixes to make it easier for others to test
with.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some cores like the USB core have two address spaces. In the USB host
controller one address space is used for the OHCI and the other for the
EHCI controller interface. The USB controller is the only core I found
with two address spaces. This code is based on the AI scan function
ai_scan() in shared/aiutils.c in the Broadcom SDK.
CC: Rafał Miłecki <zajec5@gmail.com>
CC: linux-wireless@vger.kernel.org
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bcma should check for a fallback sprom every time it can not find a
sprom on the card itself or a normal external sprom mapped into the
memory of the chip. When otp sprom support was introduced it tried to
read out the sprom from the wireless chip also if no otp sprom was
available. This caused a Data bus error in bcma_sprom_get() when
reading out the sprom for the SoC.
This fixes a regression introduced in commit:
commit 10d8493cd9
Author: Arend van Spriel <arend@broadcom.com>
Date: Tue Mar 6 15:50:48 2012 +0100
bcma: add support for on-chip OTP memory used for SPROM storage
This patch was tested on a Netgear WNDR3400 (Broadcom BCM4718 SoC).
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following is seen during allmodconfig builds for MIPS:
drivers/bcma/driver_pci_host.c:518:2: error: implicit declaration
of function 'pcibios_enable_device' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/bcma/driver_pci_host.o] Error 1
Most likey introduced by commit 49dc957715
"bcma: add PCIe host controller"
Add the header instead of implicitly assuming it will be present.
Sounds like a good idea, but that alone doesn't fix anything.
The real problem is that the Kconfig has settings related to whether
PCI is possible, i.e.
config BCMA_HOST_PCI_POSSIBLE
bool
depends on BCMA && PCI = y
default y
config BCMA_HOST_PCI
bool "Support for BCMA on PCI-host bus"
depends on BCMA_HOST_PCI_POSSIBLE
...but what is missing is that BCMA_DRIVER_PCI_HOSTMODE doesn't
have any dependencies on the above. Add one.
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless Broadcom chips can have either their SPROM data stored
on either external SPROM or on-chip OTP memory. Both are accessed
through the same register space. This patch adds support for the
on-chip OTP memory.
Tested with:
BCM43224 OTP and SPROM
BCM4331 SPROM
BCM4313 OTP
This patch is in response to linux-wireless thread [1].
[1] http://article.gmane.org/gmane.linux.kernel.wireless.general/85426
Tested-by: Saul St. John <saul.stjohn@gmail.com>
Tested-by: Rafal Milecki <zajec5@gmail.com>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When not SPROM is available a fallback mechanism is used. However,
when that fails the code currently continues. This patch assures
that the bcma_sprom_get() function aborts when that happens.
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On SoCs the sprom is stored in the nvram in a special partition on the
flash chip. The nvram contains the sprom for the main bus, but
sometimes also for a pci devices using bcma. This patch makes it
possible for the arch code to register a function to fetch the needed
sprom from the nvram and provide it to the bcma code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is needed by the bcm47xx arch code to get the number of
the ieee80211 core.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes us see what type of hardware someone uses by the dmesg
output.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This check is needed on the BCM43224 device as it says in the
capabilities it has an sprom but is extra check says it has not.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have two bcma buses on one computer the second will not work
without this patch. Now each bus gets an own number.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some SoCs have a PCIe host controller to make it possible to attach
some other devices to it, like an other Wifi card.
This code was tested with an Netgear WNDR3400 (bcm4716 based), but
should work with all bcma based SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_core_pci_hostmode_init() has to be in __devinit as it will call a
function in that section and so all functions calling it also have to
be in __devinit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are many magic numbers used in the PCIe code. Replace them with
some constants from the Broadcom SDK and also use them in the pcie host
controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some SoCs have two pcie or gmac cores and we need to know the number of
the specific core on the bus. This is the case for the BCM4706.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmsmac driver is now using the bcma SPROM CRC check, which does
not recognize all chipsets that were functional prior to the switch. In
particular, the current code bails out on odd CRC errors in recent
Macbooks. This patch ignores those errors, with the argument that an
unrecognized SPROM should be treated similarly to a non-existing one.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_bus_scan() leaks 'struct bcma_device' bytes if
bcma_get_next_core() returns error.
Restructure the code so we always kfree() the memory we allocate to
the variable 'core' before it goes out of scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SPROM location has been relocated again for some devices. This patch
will log the offset when CONFIG_BCMA_DEBUG has been selected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the low-level driver actually gets informed that it is getting suspended and resumed.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
.. and connect it up with the pci host bcma driver.
Now, the next step is to connect those bcma bus-level suspend/resume
functions to the actual bcma device suspend resume functions.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
.. and avoid doing the unnecessary PCI operations - the PCI layer will
do them for us.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This clears the currently mapped core when suspending, to force
re-mapping after resume. Without that we were touching default core
registers believing some other core is mapped. Such a behaviour
resulted in lockups on some machines.
Cc: stable@vger.kernel.org
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma used to lock up machine without enabling PCI or initializing CC.
Cc: stable@vger.kernel.org
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some cores are mapped in the fixed way, they registers can be accessed
all the time.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix in advance, or we will get things like this:
drivers/bcma/core.c:20: warning: data definition has no type or storage class
drivers/bcma/core.c:20: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
drivers/bcma/core.c:20: warning: parameter names (without types) in function declaration
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This will ensure that it continues to build once we remove
the implicit module.h presence from everywhere later on.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The u32 would never be less than zero so the error handling would
break. I changed it to s32 to match how bcma_erom_get_mst_port() is
declared.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to disable ext. PA lines for reading SPROM. It's disabled by
default, but this patch allows using bcma after loading wl, which leaves
workaround enabled.
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add method to return the clock of the CPU. This is needed by the arch
code to calculate the mips_hpt_frequency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for serial console to bcma, when operating on an SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a mips driver to bcma. This is only found on embedded
devices. For now the driver just initializes the irqs used on this
system.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for using bcma on a Broadcom SoC as the system
bus. An SoC like the bcm4716 could register this bus and use it to
searches for the bcma cores and register the devices on this bus.
BCMA_HOSTTYPE_NONE was intended for SoCs at first but BCMA_HOSTTYPE_SOC
is a better name.
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip common and mips core have to be setup early in the boot
process to get the cpu clock.
bcma_bus_early_register() gets pointers to some space to store the core
data and searches for the chip common and mips core and initializes
chip common. After that was done and the kernel is out of early boot we
just have to run bcma_bus_register() and it will search for the other
cores, initialize and register them.
The cores are getting the same numbers as before.
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it possible to use this code in some other method.
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the parsing of the EEPROM data in scan function for one core into
an own function. Now we are able to use it in some other scan function
as well.
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
linux-next-20110722/drivers/bcma/driver_pci.c:175: error: 'SSB_PCICORE_BFL_NOPCI' undeclared (first use in this function)
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
