While the OLPC display appears to be able to handle either positive
or negative sync, the Display Controller only recognises positive sync.
This brings viafb (for XO-1.5) in line with lxfb (for XO-1) and
fixes a recent regression where the XO-1.5 DCON could no longer be
frozen. Thanks to Florian Tobias Schandinat for helping identify
the fix.
Test case: from a vt,
echo 1 > /sys/devices/platform/dcon/freeze
should cause the current screen contents to freeze, rather than garbage being
displayed.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@kernel.org
Patch follows the disable and software reset sequence specified
in version2 to LCDC functional specification.
Without this flicker is observed on re-enabling the LCDC.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
DSICTRL should be called after all mipi settings
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
SYSCONF should be set after PHYCTRL
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
sh_mipi_setup() should be called after setting of CPG
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
SH MIPI manual explains the calculation method of HBP/HFP.
it is based on HSbyteCLK settings.
SH73a0 chip can use HS6divCLK/HS4divCLK for it.
This patch has compatibility to SH7372 mipi
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Dot clock of SH MIPI are depends on each platform board.
This patch adds set_dot_clock() function for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
VMLEN1/VMLEN2 needs blanking length which is calculated from
video image size.
The calculation methods are explained on
[SH MIPI] - [Video Mode] - [Blanking Packet setting]
But HFPLEN (= VMLEN2) is un-understandable.
For example, if SH-MIPI input was RGB888 (3byte),
output was RGB888 (3byte)
and 3lane connection, the date goes straight.
But if SH-MIPI input was RGB888 (3byte),
output was RGB565 (2byte)
and 4lane connection, it needs delay in HFPLEN.
Then (input cycle - output cycle) * lane is necessary the delay
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
SH MIPI DSI can use 0-4 lane
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
VMCTR2 parameter will be supported more in the future.
1 << xx style is easy to understand.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
dsipck clock is controled by CLKDEV_ICK_ID() in clock-shxxx.
dsi0p_clk/dsi1p_clk naming is not needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
LDHAJR register will be broken by hsync_pos without this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This converts the remaining USB drivers in the kernel to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Till Harbaum <till@harbaum.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current code calculates scaling factors for video overlays even when the
overlays are not scaled. Change the code to skip calculations when not
scaling.
This optimizes the code a bit, but also fixes a problem when configuring
an overlay for a disabled display: if the display is disabled we don't
necessarily know the pixel clock used when the display is enabled, and
in some cases (like HDMI) the pixel clock is set to zero until a proper
video mode is set later. A wrong pixel clock will mess up the
scaling calculations, causing an error like:
omapdss DISPC error: failed to set up scaling, required fclk rate = 0
Hz, current fclk rate = 170666666 Hz
A proper fix would be to check later whether the clocks are enough for the
scaling, at the point when the overlay or display is actually enabled,
but this patch removes the problem for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix warnings similar to this by including module.h:
drivers/video/omap/dispc.c:276:1: warning: data definition has no type
or storage class
drivers/video/omap/dispc.c:276:1: warning: type defaults to 'int' in
declaration of 'EXPORT_SYMBOL'
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_get_pixel_clock() returns the pixel clock in Hz, but the pck is
stored as kHz. This means the return value has to be multiplied by 1000,
not by 10000 as the code did.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Transparency length is fixed for pixel blending in order to support
ARGB 8888 format.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Some Village Tronic Picasso IV graphics cards identify as a 64 MiB Zorro
device in Zorro III mode.
While the total graphics memory size is the same on such cards, the offset
of the graphics memory differs. Add a quirk to handle this.
Based on src/sys/arch/amiga/dev/grf_cl.c from NetBSD.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
In Zorro II mode, the Village Tronic Picasso IV graphics card shows up as
either 2 or 3 Zorro devices:
- One for the registers of the Cirrus Logic graphics chip,
- One for the first bank of 2 MiB of graphics memory,
- An optional one for the second bank of 2 MiB of graphics memory,
if there was enough free Zorro II address space.
Based on src/sys/arch/amiga/dev/grf_cl.c from NetBSD.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
As indicated by commit a7f4d00a82 ("zorro:
Defer device_register() until all devices have been identified"), cirrusfb
crashes if zorro_find_device() cannot find an expected device.
Rewrite the Zorro device probe code to make it more robust, easier to
understand, and more extensible.
Other logical changes:
- For cards that show up as 2 Zorro devices, autoprobe graphics memory
sizes based on the size of the Zorro device containing the graphics
memory.
Acording to the NetBSD sources, this is safe.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The newer Atmel SoCs use normal 16bit 565 BGR/RGB for the palette data,
rather than the special intensity + 555 format.
Fill out palette data correctly on these devices, and at the same time
respect the RGB/BGR wiring mode.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
If used with negative polarity the PWM unit cannot be disabled. This would
result in a full contrast screen.
Instead let the PWM unit enabled using 0x0 as compare value which darkens
the display.
In result no power saving is possible if inverted contrast polarity
is used.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
In the AT91SAM9263 Manual the HFP part in LCDTIM2 is described as follows:
* HFP: Horizontal Front Porch
Number of idle LCDDOTCK cycles at the end of the line.
Idle period is (HFP+2) LCDDOTCK cycles.
It is only a minor issue. I also changed all boards using atmel_lcdfb
I found to respect the new calculation.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This four year old subsystem does not have a single in-tree user
not even in staging and as far as I know also none out-of-tree.
I think that justifies removing it which cleans the config up.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: James Simmons <jsimmons@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
ARM: pxa/cm-x300: properly set bt_reset pin
ARM: mmp: rename SHEEVAD to GPLUGD
ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
ARM: i.MX28: shift frac value in _CLK_SET_RATE
plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
ARM: mx5: fix clock usage for suspend
ARM: pxa: use correct __iomem annotations
ARM: pxa: sharpsl pm needs SPI
ARM: pxa: centro and treo680 need palm27x
ARM: pxa: make pxafb_smart_*() empty when not enabled
ARM: pxa: select POWER_SUPPLY on raumfeld
ARM: pxa: pxa95x is incompatible with earlier pxa
ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
ARM: pxa: pxa95x/saarb depends on pxa3xx code
ARM: pxa: allow selecting just one of TREO680/CENTRO
ARM: pxa: export symbols from pxa3xx-ulpi
ARM: pxa: make zylonite_pxa*_init declaration match code
ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
ARM: at91: add defconfig for at91sam9g45 family
ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
...
The rename of corgibl_limit_intensity is missed in commit d00ba726
("backlight: Rename the corgi backlight driver to generic"). Let's fix it
now.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using gpio_request_one can make the error handling simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The regulator support in the l4f00242t03 is very non-idiomatic. Rather
than requesting the regulators based on the device name and the supply
names used by the device the driver requires boards to pass system
specific supply names around through platform data. The driver also
conditionally requests the regulators based on this platform data, adding
unneeded conditional code to the driver.
Fix this by removing the platform data and converting to the standard
idiom, also updating all in tree users of the driver. As no datasheet
appears to be available for the LCD I'm guessing the names for the
supplies based on the existing users and I've no ability to do anything
more than compile test.
The use of regulator_set_voltage() in the driver is also problematic,
since fixed voltages are required the expectation would be that the
voltages would be fixed in the constraints set by the machines rather than
manually configured by the driver, but is less problematic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error. This is obsolete meanwhile, the core
will do it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
They were getting this implicitly by an include of module.h
from device.h -- but we are going to clean that up and break
that include chain, so include module.h explicitly now.
[ with contributions from Axel Lin <axel.lin@gmail.com> ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These comments mention CONFIG options that do not exist: not as a symbol
in a Kconfig file (without the CONFIG_ prefix) and neither as a symbol
(with that prefix) in the code.
There's one reference to XSCALE_PMU_TIMER as a negative dependency.
But XSCALE_PMU_TIMER is never defined (CONFIG_XSCALE_PMU_TIMER is
also unused in the code). It shows up with type "unknown" if you search
for it in menuconfig. Apparently a negative dependency on an unknown
symbol is always true. That negative dependency can be removed too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves media and video drivers to use new enum
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (270 commits)
video: platinumfb: Add __devexit_p at necessary place
drivers/video: fsl-diu-fb: merge diu_pool into fsl_diu_data
drivers/video: fsl-diu-fb: merge diu_hw into fsl_diu_data
drivers/video: fsl-diu-fb: only DIU modes 0 and 1 are supported
drivers/video: fsl-diu-fb: remove unused panel operating mode support
drivers/video: fsl-diu-fb: use an enum for the AOI index
drivers/video: fsl-diu-fb: add several new video modes
drivers/video: fsl-diu-fb: remove broken screen blanking support
drivers/video: fsl-diu-fb: move some definitions out of the header file
drivers/video: fsl-diu-fb: fix some ioctls
video: da8xx-fb: Increased resolution configuration of revised LCDC IP
OMAPDSS: picodlp: add missing #include <linux/module.h>
fb: fix au1100fb bitrot.
mx3fb: fix NULL pointer dereference in screen blanking.
video: irq: Remove IRQF_DISABLED
smscufx: change edid data to u8 instead of char
OMAPDSS: DISPC: zorder support for DSS overlays
OMAPDSS: DISPC: VIDEO3 pipeline support
OMAPDSS/OMAP_VOUT: Fix incorrect OMAP3-alpha compatibility setting
video/omap: fix build dependencies
...
Fix up conflicts in:
- drivers/staging/xgifb/XGI_main_26.c
Changes to XGIfb_pan_var()
- drivers/video/omap/{lcd_apollon.c,lcd_ldp.c,lcd_overo.c}
Removed (or in the case of apollon.c, merged into the generic
DSS panel in drivers/video/omap2/displays/panel-generic-dpi.c)
* 'clk' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7131/1: clkdev: Add Common Macro for clk_lookup
clk: spi-pl022: convert to clk_prepare()/clk_unprepare()
clk: timer-sp: convert to clk_prepare()/clk_unprepare()
clk: sa1111: convert to clk_prepare()/clk_unprepare()
clk: mmci: convert to clk_prepare()/clk_unprepare()
clk: amba-pl011: convert to clk_prepare()/clk_unprepare()
clk: amba-pl010: convert to clk_prepare()/clk_unprepare()
clk: amba-clcd: convert to clk_prepare()/clk_unprepare()
clk: amba bus: convert to clk_prepare()/clk_unprepare()
clk: provide prepare/unprepare functions
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
rtmutex: Add missing rcu_read_unlock() in debug_rt_mutex_print_deadlock()
lockdep: Comment all warnings
lib: atomic64: Change the type of local lock to raw_spinlock_t
locking, lib/atomic64: Annotate atomic64_lock::lock as raw
locking, x86, iommu: Annotate qi->q_lock as raw
locking, x86, iommu: Annotate irq_2_ir_lock as raw
locking, x86, iommu: Annotate iommu->register_lock as raw
locking, dma, ipu: Annotate bank_lock as raw
locking, ARM: Annotate low level hw locks as raw
locking, drivers/dca: Annotate dca_lock as raw
locking, powerpc: Annotate uic->lock as raw
locking, x86: mce: Annotate cmci_discover_lock as raw
locking, ACPI: Annotate c3_lock as raw
locking, oprofile: Annotate oprofilefs lock as raw
locking, video: Annotate vga console lock as raw
locking, latencytop: Annotate latency_lock as raw
locking, timer_stats: Annotate table_lock as raw
locking, rwsem: Annotate inner lock as raw
locking, semaphores: Annotate inner lock as raw
locking, sched: Annotate thread_group_cputimer as raw
...
Fix up conflicts in kernel/posix-cpu-timers.c manually: making
cputimer->cputime a raw lock conflicted with the ABBA fix in commit
bcd5cff721 ("cputimer: Cure lock inversion").
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
According to the comments in include/linux/init.h:
"Pointers to __devexit functions must use __devexit_p(function_name), the
wrapper will insert either the function_name or NULL, depending on the config
options."
We have __devexit annotation for platinumfb_remove(), thus add __devexit_p at
necessary place.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This tries to clear up the confusion between integers and iomem pointers
in the marvell pxa platform. MMIO addresses are supposed to be __iomem*
values, in order to let the Linux type checking work correctly. This
patch moves the cast to __iomem as far back as possible, to the place
where the MMIO virtual address windows are defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The diu_pool structure contains diu_addr objects for various objects
allocated in DMA space that are used by the DIU, but the only instance
of this structure is a global variable, 'pool'. Eliminate 'pool' by
merging its fields into the fsl_diu_data structure, which is instantiated
on the heap for each DIU controller found.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The diu_hw structure contains two fields used to access the DIU registers,
but the only instance of this structure is a global variable, 'dr'.
Eliminate 'dr' by merging its fields into the fsl_diu_data structure,
which is instantiated on the heap for each DIU controller found.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The Freescale DIU video controller supports five video "modes", but only
the first two are used by the driver. The other three are special modes
that don't make sense for a framebuffer driver. Therefore, there's no
point in keeping a global variable that indicates which mode we're
supposed to use.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The MFB_TYPE_xxx macros indicate different "operating modes" of each AOI,
but this feature is not actually used in the driver. The mfb_index.type
field is always set to MFB_TYPE_OUTPUT, so just delete it and any code
that references it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Each of the five AOIs created by the DIU driver has a special purpose, and
they're not treated equally. It makes sense to identify them with an enum
instead of a hard-coded number.
Since the 'index' is now an enum, it can only contain allowed values, so
there's no need to check for an invalid value. This simplifies some other
code, such as fsl_diu_disable_panel(), which no longer needs to return an
error code.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add the following new video modes to the Freescale DIU framebuffer driver:
640x480x60
640x480x72
640x480x75
640x480x90
640x480x100
800x480x60
800x600x60
854x480x60
1280x480x60
1280x720x60
1920x1080x60
Also add margin data to the 320x240 video mode. This mode was originally
intended only for the AOIs (overlays) used on planes two and three, but with
real margin data, it can now be used as an actual video mode.
Video mode data is from earlier work done by Jerry Huang
<Chang-Ming.Huang@freescale.com>.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The function which is supposed to provide screen blanking support doesn't
actually do anything, so the framebuffer layer thinks the screen has
been blanked when it really isn't. Remove the code completely for now.
A side-effect of this change is that the framebuffer console blanking now
works correctly. Presumably this is because the console now receives -EINVAL
instead of '0' when it asks the driver to blank the screen, so the console
does it manually now.
A signficant refactoring of the driver is planned, and proper hardware
blanking support will added afterwards.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Move several macros and structures from the Freescale DIU driver's header
file into the source file, because they're only used by that file. Also
delete a few unused macros.
The diu and diu_ad structures cannot be moved because they're being used
by the MPC5121 platform file. A future patch eliminate the need for
the platform file to access these structs, so they'll be moved also.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Use the _IOx macros to define the ioctl commands, instead of hard-coded
numbers. Unfortunately, the original definitions of MFB_SET_PIXFMT and
MFB_GET_PIXFMT used the wrong value for the size, so these macros have
new values now. To avoid breaking binary compatibility with older
applications, we retain support for the original values, but the driver
displays a warning message if they're used.
Also remove the FBIOGET_GWINFO and FBIOPUT_GWINFO ioctls. FBIOPUT_GWINFO
was never implemented, and FBIOGET_GWINFO was never used by any
application.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Revised LCD controller in upcoming TI SoC which is an updated version of
LCDC IP that was found on TI's DA850 SoC supports 2048*2048 resolution.
Below are the encoding details:
Width:
Pixels Per Line = {pplmsb, ppllsb, 4'b1111} + 1
Where pplmsb:1bit==>Raster Timing0[3], ppllsb:6bits==>Raster Timing0[9:4].
And encoded value can range from 16 to 2048 in multiples of 16.
Height:
Lines Per Panel = {lpp_b10, lpp}
Where lpp:10bits==>Raster Timing1[9:0], lpp_b10:1bit==>Raster Timing2[26].
And encoded value can range from 1 to 2048, programmable range is 0 to
2047.
Patch is verified on emulation platform of upcoming SoC for updated
feature and on DA850 platform to make sure nothing existing breaks.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Compiling panel-picodlp.c failed with:
drivers/video/omap2/displays/panel-picodlp.c:560:12: error:
'THIS_MODULE' undeclared here (not in a function)
Add #include <linux/module.h> to get THIS_MODULE definition.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Removes some bitrot from the au1100fb driver and fix it up so it works again.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
When blanking an already blanked framebuffer, a kernel NULL pointer
dereference occurred, because mx3fb driver handles all kinds of screen
blanking (normal, vsync suspend, powerdown) in the same way.
Certain programs (Xorg X11 server) first do a normal blank, followed by
a powerdown blank, which triggered the bug.
Add an additional safeguard and make sdc_disable_channel() safe against
multiple calls independent of other logic.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Having "edid" as char caused a problem in ufx_read_edid() where we
compared "edid[i] != 0xFF". Because of the type difference, the
condition was never true and the error checking failed.
Also I added a __user notation to silence a sparse complaint.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add zorder support on OMAP4, this feature allows deciding the visibility order
of the overlays based on the zorder value provided as an overlay info parameter
or a sysfs attribute of the overlay object.
Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is
supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER
if the caps are not available.
Ensure that all overlays that are enabled and connected to the same manager
have different zorders. Swapping zorders of 2 enabled overlays currently
requires disabling one of the overlays.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for VIDEO3 pipeline on OMAP4:
- Add VIDEO3 pipeline information in dss_features and omapdss.h
- Add VIDEO3 pipeline register coefficients in dispc.h
- Create a new overlay structure corresponding to VIDEO3.
- Make changes in dispc.c for VIDEO3
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed
to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On
OMAP4, alpha blending is always enabled by default, if the above bits are set,
we switch to an OMAP3 compatibility mode where the zorder values in the pipeline
attribute registers are ignored and a fixed priority is configured.
Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for
more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and
FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4
alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is
expected to check for the ZORDER cap, if an overlay doesn't have this cap, the
user is expected to set the parameter partial_alpha_enabled. If the overlay has
ZORDER cap, the DSS2 user can assume that alpha blending is already enabled.
Don't support OMAP3 compatibility mode for now. Trying to read/write to
alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not
set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits.
Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use
overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha
blending or not. Replace this with checks for VIDEO1 pipeline.
Cc: linux-media@vger.kernel.org
Cc: Lajos Molnar <molnar@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Four of the LCD panel drivers depend on the backlight class,
so add the dependency in Kconfig.
Selecting the BACKLIGHT_CLASS_DEVICE symbol does not generally
work since it has other dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[tomi.valkeinen@ti.com: changed also N8x0 panel]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
overlay_info struct, used to configure overlays, currently includes both
physical and virtual addresses for the pixels. The vaddr was added to
support more exotic configurations where CPU would be used to update a
display, but it is not currently used and there has been no interest in
the feature. Using CPU to update a screen is also less interesting now
that OMAP4 has two LCD outputs.
This patch removes the vaddr field, and modifies the users of omapdss
accordingly. This makes the use of omapdss a bit simpler, as the user
doesn't need to think if it needs to give the vaddr.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support to dump the HDMI wrapper, core, PLL and PHY registers
through debugfs.
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: updated the description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add some of the missing register definitions, which are h/w indexable.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove usage of hdmi_reg struct to use u16 instead in the HDMI IP header
file. hdmi_reg struct is not really needed, and the same change was also
made for dispc earlier.
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: updated the description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move the comments in AVI infoframe structure above each parameter
to align with other comments in the header file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This is a driver for N800's display, ported from the old omapfb. This is
a slightly lighter version of the driver as not all features of the old
driver can be ported without big changes to DSS2, and also because some
of the HW features used in the old driver are unclear (e.g. the power
management part).
That said, the new driver works fine for basic use.
Architecturally the driver is not as neat as it could be. N800's display
HW consists of a display buffer chip and a panel, and ideally they would
be represented by separate, independent drivers. This is not currently
possible, and this driver contains both buffer chip and panel driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Port the old omapfb panel driver for Apollon to DSS2.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
drivers/video/omap/ contains some lcd drivers which are not used by any
board. They can be removed.
Cc: Arun C <arunedarath@mistralsolutions.com>
Acked-by: Koen Kooi <koen@openembedded.org>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Taal panel driver supports two kinds of backlight control: 1) using DSI
commands sent to the panel to control the backlight, 2) calling function
pointers going to the board file to control the backlight.
The second option is a bit hacky, and will no longer be needed when the
PWM driver supports the backlight features. After that we can use the
standard PWM backlight driver.
This patch removes the second backlight control mechanism, and adds a
boolean field, use_dsi_backlight, to nokia_dsi_panel_data which the
board file can use to inform whether the panel driver should use DSI
commands to control the backlight.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create a dss_range_param member called FEAT_PARAM_DOWNSCALE to get the maximum
downscaling possible on the current platform. Use this in
dispc_ovl_calc_scaling().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move DISPC scaling related code from dispc_ovl_setup() to a new function
dispc_ovl_calc_scaling(). Use overlay caps to check if the overlay can scale or
not. No functional changes are made.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function calc_fclk_five_taps() uses a fixed value of pixels per line which
is used in calculations to get the minimum fclk needed for scaling with five
taps to work.
Remove this by providing the width of the panel connected to the manager.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_pclk_rate() is used to calculate minimum required functional clock for
scaling in calc_fclk() and calc_fclk_five_taps(). This function returns the
correct pixel clock for LCD and LCD2 managers, but not for TV manager. Extend
this function so that it gets the correct pixel clock for TV manager.
This also prevents the crash we get when we try to scale overlays connected to
TV manager. The current code leads to a BUG() being executed if we call
dispc_mgr_pclk_rate() for the TV manager.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create a helper function called dispc_mgr_is_lcd() which returns true if the
manager is LCD or LCD2.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_ovl_enable_replication() and dispc_ovl_set_fifo_threshold() are currently
called in configure_overlay(). These are the only functions which cause DISPC
register writes of overlay parameters outside of dispc_ovl_setup().
Move these to dispc_ovl_setup() and pass replication, fifo_low and fifo_high
thresholds as arguments to dispc_ovl_setup() in order to be aligned with other
overlay parameters. No functional changes are made.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_ovl_setup() currently takes a large number of overlay arguments, most of
these are members of the overlay_info struct. Replace these arguments by
passing a overlay_info pointer instead.
In configure_overlay(), we create an overlay_info struct called new_oi, this is
a copy of the overlay cache's overlay_info member. Update the new_oi parameters
which could have been possibly changed in configure_overlay(). Pass its pointer
pointer to dispc_ovl_setup().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the new read_edid() function to get EDID information from the
display (when available), and use the information to use a suitable mode
at initialization time.
Hot-plug is not yet supported, so the timings selected at init time will
stay even if the monitor would be changed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have currently panel-generic-dpi driver, which is a combined driver
for dummy panels and also for DVI output.
The aim is to split the panel-generic-dpi into two, one for fixed size
dummy panels connected via DPI, and the other (this) for variable
resolution output which supports DDC channel (in practice a DVI framer
chip connected to DPI output).
Original i2c code by: Ricardo Salveti de Araujo
<ricardo.salveti@canonical.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implement detect() by checking the hot plug detect status.
The implementation is not very good, as it always turns on the HDMI
output to get the detection working. HDMI driver needs improvements so
that we could enable only core parts of it.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
check_timings() is supposed to be used to verify if timings are ok or
not. Currently the HDMI driver prints error messages if the timings are
not ok. This is not right, as it is no error to give invalid timings to
check_timings().
Remove the error prints.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up reading of EDID by passing direct address to the block being
read, instead of start address of the whole EDID memory area. Rewrite
the loop which reads the EDID.
This also fixes the checksum calculation, which used to calculate the
checksum only for the first block.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the DDC initialization off from hdmi_core_ddc_edid() into a
separate function hdmi_core_ddc_init(). This cleans up the
implementation.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAPFB handles EDID parsing now, using the common helper functions in
fbdev. We can remove the EDID parsing from HDMI driver.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implement read_edid() for HDMI by implementing necessary functions to
hdmi.c and to hdmi_omap4_panel.c.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently the set_timings code for hdmi is quite strange. The display is
disabled in hdmi_omap4_panel.c before setting timings, and enabled in
hdmi.c after setting the timings. Furthermore, the timings were not
permanent, and disabling and enabling the display would lose them.
This patch makes the set_timings handling a bit better.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Enabling HDMI output often causes sync lost errors, and almost always
causes timeout errors being printed from dispc_mgr_enable_digit_out().
The sync lost problem seems to go lessen greatly if we first enable the
HDMI output, and only then enable the DISPC output. However, as this is
only based on observations, the fix may not be perfect as the problem
may lie somewhere else. Nevertheless, HDMI works better with this patch.
This will also fix the dispc's dispc_mgr_enable_digit_out(), as the code
waits for two VSYNCs after enabling the output. If the HDMI output is
disabled (as it was previously), there are no VSYNCs and
dispc_mgr_enable_digit_out() will print timeout errors.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_enable_digit_out() didn't handle HDMI case very well.
Improve the function to use FRAMEDONETV interrupt to see when HDMI has
been disabled.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dss_get_hdmi_venc_clk_source(), which can be used to get the value
programmed with dss_select_hdmi_venc_clk_source(). This can be used to
find out if the digit output is going to VENC or HDMI.
For OMAP2/3 dss_get_hdmi_venc_clk_source() always returns
DSS_VENC_TV_CLK.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regn divider is currently programmed to the registers without change,
but when calculating clock frequencies it is used as regn+1.
To make this similar to how DSI handles the dividers this patch changes
the regn value to be used as such for calculations, but the value
programmed to registers is regn-1.
This simplifies the clock frequency calculations, makes it similar to
DSI, and also allows us to use regn value 0 as undefined.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use default regn and regm2 dividers in the hdmi driver if the board file
does not define them.
Cc: Mythri P K <mythripk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current driver had a hardcoded minimum value of 2 for pixel clock
divisor (PCD). This doesn't seem to be right.
OMAP4 TRM says that PCD can be 1 when not downscaling, and inverted
pixel clock (IPC) is off.
OMAP3 TRM says the same, but also in the register descriptions that PCD
value 1 is invalid.
OMAP2 TRM says PCD 2 is the minimum.
OMAP2 is still untested, but for both OMAP3 and OMAP4 PCD of 1 seems to
work fine.
This patch adds a new DSS feature, FEAT_PARAM_DSS_PCD, which is used to
find the minimum and maximum PCD. The minimum is set to 2 for OMAP2, and
1 for OMAP3/4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the panel driver will remain generic across OMAP's renaming it to
hdmi_panel.c
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI IP fundamentally has replaceable core PHY and PLL blocks.
These blocks might vary across OMAP's but the end functionality such as to
enable or disable PLL, PHY, function to read EDID would remain the same.
Thus to make the current hdmi DSS driver compatible with different OMAP's having
different IP blocks( A combination of different core, PHY, PLL blocks), function
pointer approach is introduced.
With function pointer, relevant IP dependent functions are mapped to the generic
functions used by DSS during the initialization based on the OMAP compiled.
Thus making hdmi DSS driver IP agnostic.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Functions that are included in HDMI IP driver is renamed to have
IP specific names so that it will not conflict with similar functions
from other IP.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move HDMI IP dependent audio functions from HDMI DSS file to IP library.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the current HDMI driver to move the HDMI IP dependent ( PLL/PHY/Core
configuration code) to a new IP file (ti_hdmi_4xxx_ip.c.
This is to separate IP dependent OMAP agnostic code from OMAP specific DSS
dependent code.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up to move the EDID definition from the IP dependent header file to hdmi.c
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Some of the header file definitions that are there in the hdmi.h are generic
and can be used across OMAP's, Thus moving generic definition to new file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As hdmi has few additional parameters such as vsync and hsync
polarity which is missing in DSS timing structure, define HDMI timings
structure for hdmi to use instead of OMAP DSS timing structure.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the pll and the video configuration info are part of the ip_data, pll
and video structures are moved to the ip_data structure. Also the pll and
video configuration functions are modified accordingly to take care of the
structure movement.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the base_address of the HDMI might differ across SoC's, offset of the HDMI
logical blocks(PHY, PLL and Core) and base address procured from the platform
data are passed dynamically to the functions that modify HDMI IP registers.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add initial support for DSI video mode panels:
- Add a new structure omap_dss_dsi_videomode_data in the member "panel" in
omap_dss_device struct. This allows panel driver to configure dsi video_mode
specific parameters.
- Configure basic DSI video mode timing parameters: HBP, HFP, HSA, VBP, VFP, VSA,
TL and VACT.
- Configure DSI protocol engine registers for video_mode support.
- Introduce functions dsi_video_mode_enable() and dsi_video_mode_disable() which
enable/disable video mode for a given virtual channel and a given pixel format
type.
Things left for later
- Add functions to check for errors in video mode timings provided by panel.
- Configure timing registers required for command mode interleaving.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_vc_send_null() currently sends a long packet with data type
MIPI_DSI_NULL_PACKET and packet length 4. Modify it to send a zero
length long packet. This leads to sending only the long packet header
and no payload packets and hence the transfer completes faster.
The function can be modified later if there is a need to send null
packets of a non-zero length.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, DSI pixel info is only represented by the pixel size in bits using
the pixel_size parameter in omap_dss_device struct's ctrl member.
This is not sufficient information for DSI video mode usage, as two of the
supported formats(RGB666 loosely packed, and RGB888) have the same pixel
container size, but different data_type values for the video mode packet header.
Create enum "omap_dss_dsi_pixel_format" which describes the pixel data format
the panel is configured for. Create helper function dsi_get_pixel_size() which
returns the pixel size of the given pixel format.
Modify functions omapdss_default_get_recommended_bpp() and dss_use_replication()
to use dsi_get_pixel_size().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the function dispc_set_parallel_interface_mode() into 2 separate
functions called dispc_mgr_set_io_pad_mode() and dispc_mgr_enable_stallmode().
The current function tries to set 2 different modes(io pad mode and stall mode)
based on a parameter omap_parallel_interface_mode which loosely corresponds to
the panel interface type.
This isn't correct because a) these 2 modes are independent to some extent,
b) we are currently configuring gpout0/gpout1 for DSI panels which is
unnecessary, c) a DSI Video mode panel won't get configured correctly.
Splitting the functions allows the interface driver to set these modes
independently and hence allow more flexibility.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce read functions which use generic Processor-to-Peripheral
transaction types. These are needed by some devices which may not support
corresponding DCS commands.
Add function dsi_vc_generic_send_read_request() which can send
a short packet with 0, 1 or 2 bytes of request data and the corresponding
generic data type.
Rename function dsi_vc_dcs_read_rx_fifo() to dsi_vc_read_rx_fifo() and modify
it to take the enum "dss_dsi_content_type" as an argument to use either DCS
or GENERIC Peripheral-to-Processor transaction types while parsing data read
from the device.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split dsi_vc_dcs_read() into the functions:
- dsi_vc_dcs_send_read_request(): This is responsible for sending the short
packet command with the read request.
- dsi_vc_dcs_read_rx_fifo(): This parses the DSI RX fifo of the given virtual
channel, identifies the type of data received, and fills a buffer with the data
provided by the panel.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove functions dsi_vc_dcs_read_1() and dsi_vc_dcs_read_2(), these are used
when the panel is expected to return 1 and 2 bytes respecitvely. This was manily
used for debugging purposes. These functions should be implemented in the panel
driver if needed.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Intoduce enum "dss_dsi_content_type" to differentiate between DCS and generic
content types.
Introduce short and long packet write functions which use generic
Processor-to-Peripheral transaction types. These are needed by some devices
which may not support corresponding DCS commands. Create common write functions
which allow code reuse between DCS and generic write functions.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create an enum for DSI operation modes, use this to set the capabilities of the
device in dsi_init_display().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The enum type dsi_vc_mode is a bit misleading as L4 slave port and video port
are sources to VC rather than the mode of operation. Rename then enum type and
its members. Merge dsi_vc_config_vp() and dsi_vc_config_l4() into a single
function called dsi_vc_config_source() which takes dsi_vc_source enum as an
extra argument.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
MIPI DSI Transaction types and DCS commands are currently defined as
macros in dsi.c and panel-taal.c, remove these and replace them with
enum members defined in include/video/mipi_display.h.
Signed-off-by: Archit Taneja <archit@ti.com>
[tomi.valkeinen@ti.com: reformatted the commit message]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for Innolux AT070TN83, a 7 inch LCD
with RGB-Interface and touch panel to panel-generic-dpi.
Tested with Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rename dispc's manager related functions as follows:
- Remove prepending underscores, which were originally used to inform
that the clocks needs to be enabled. This meaning is no longer valid.
- Prepend the functions with dispc_mgr_*
- Remove "channel" from the name, e.g. dispc_enable_channel ->
dispc_mgr_enable
The idea is to group manager related functions so that it can be deduced
from the function name that it writes to manager spesific registers.
All dispc_mgr_* functions have enum omap_channel as the first parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rename dispc's overlay related functions as follows:
- Remove prepending underscores, which were originally used to inform
that the clocks needs to be enabled. This meaning is no longer valid.
- Prepend the functions with dispc_ovl_*
- Remove "plane" from the name, e.g. dispc_set_plane_ba0 ->
dispc_ovl_set_ba0
The idea is to group overlay related functions so that it can be deduced
from the function name that it writes to overlay spesific registers.
All dispc_ovl_* functions have enum omap_plane as the first parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.
Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Add support to define overlay capabilities into dss_features. The
features are set to overlay->caps at initialization time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Use lookup tables instead of switch/if in some DISPC functions to make
the code cleaner.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Remove support for non-DISPC overlays and overlay managers.
The support to possibly have non-DISPC overlays and managers was made to
make it possible to use CPU and/or sDMA to update RFBI or DSI command
mode displays. It is ok to remove the support, because:
- No one has used the feature.
- Display update without DISPC is very slow, so it is debatable if the
update would even be usable.
- Removal cleans up code.
- If such a feature is needed later, it is better implemented outside
omapdss driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
DSS driver has not been "experimental" for many years now, so perhaps
it's time to remove the text from Kconfig titles.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently when changing the manager of an overlay, set_manager() directly
calls dispc to set the overlay's destination.
Change this to be more in line with other overlay configurations, and
this will also remove the need to have dispc clocks enabled when calling
set_manager().
A new field is added to overlay struct, "manager_changed". This is
similar to "display_changed" field in manager struct, and is used to
inform apply that the manager has changed and thus write to the
registers is needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI and DSI were not cleaning up the clock source in error or uninit
cases. Set the clock source back to PRCM.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently omapfb wants that all the display devices have a driver,
otherwise omapfb refuses to start. There's no real requirement to act
like that, and this patch will make omapfb give a warning and skip that
device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, there are 2 differently named platform devices generated for
the 2 DSS DSI modules. In order to use the same driver, the dsi devices
should be 2 instances of the same platform device.
Change the platform device names from "omapdss_dsi1" and "omapdss_dsi2"
to omapdss_dsi", and set the device indices to 0 and 1.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that the HWMOD fmwk handles the fcks of DSS modules properly, the
DSS driver no longer needs to explicitely enable/disable the fck.
This patch removes the enables/disables of fck from dispc, dsi and dss.
The clk_get(fck) is still needed there, as the modules need to know the
frequency of the clock.
For hdmi and venc this patch also removes the clk_get(fck), as they
don't need the clock at all.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Uninstalling the framebuffers in reverse order is unnecessary and makes
the for-loop awkward.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
We were forgetting to unmap the video memory if fsl_diu_check_var() fails.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
It makes no sense to limit the size of a strncpy() to the length of
the source string.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Use the name "fsl-diu-fb" in the Freescale DIU framebuffer driver
during registrations.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Clean up the local variable usage in request_irq_local() and allocate_buf().
This streamlines the code without affecting functionality.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The framebuffer layer already uses the first video mode defined in the
fb_videomode array as a default, so there's no need to duplicate the
first entry into a stand-alone structure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Implement various improvements to the way the Freescale DIU framebuffer
driver access the device tree.
1) Use of_iomap() instead of of_address_to_resource() and ioremap()
2) Use be32_to_cpup() instead of directly dereferencing the device_node
pointer.
3) Rename variable 'ofdev' to 'pdev' to avoid any confusion that it's
a platform_device pointer, not an of_device pointer (of_device no
longer exists).
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fix this compilation warning in the Freescale DIU framebuffer driver:
warning: 'dummy_ad_addr' may be used uninitialized in this function
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Remove some unused ioctl commands, and treat those commands as unsupported
instead of ignored.
Also remove struct mfb_alpha, which isn't used by any ioctl. It may have
been once intended for MFB_SET_ALPHA, but that ioctl uses a different
data structure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Remove debug printk messages (they don't help in debugging), replace
printk(KERN_xxx with its pr_xxx or dev_xxx equivalent, and add a couple
missing error messages.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fix various indentation and line length problems in the Freescale
DIU framebuffer driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fix the incorrect indentation in functions fb_try_mode() and fb_find_mode().
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The array size of fifo_size array in the global dispc struct is currently
hardcoded to 3. Replace this with the MAX_DSS_OVERLAYS macro in dss_features.h,
use dss_features function to get the number of overlays instead of the
ARRAY_SIZE macro in dispc_read_plane_fifo_sizes().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over overlay id's to shorten _dispc_set_color_conv_coef()
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over manager and overlay id's to shorten dispc_save_context() and
dispc_restore_context().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over manager and overlay id's to shorten dispc_dump_regs().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Prepare dispc_dump_regs() to iterate over manager and overlay id's. Doing this
requires modifications of the macro "DUMPREG" which currently needs us to specify
the manager/overlay name to get the correct result. For example, in order to
print the register DISPC_TIMING_H(OMAP_DSS_CHANNEL_LCD), we can't iterate over
a varaible i and get the desired result through DUMPREG(DISPC_TIMING_H(i)).
Split the registers into 3 sections, the first with no arguments(common
registers), the second with one argument(manager/overlay id), and the third with
two arguments(overlay id and coefficient index), redefine DUMPREG macros for
each of these.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make the debug message useful by printing the name of the device
that no associated driver could be found for.
Signed-off-by: Andy Doan <andy.doan@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no guarantee that the error handler worker thread
will run while the dispc clocks are on. Explicitly enable/disable
them.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If a manager is moved while attached to an enabled display, the DSS
system will be left in an inconsistent state. This will eventually cause
a kernel oops when the enabled display is disabled.
Fix this by not allowing the user to move a manager away from an enabled
display.
Signed-off-by: Daniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
None of the DSS interface drivers check if an overlay manager is
connected to the display when the display is being enabled. This leads
to null pointer crash if the display has no manager.
This patch checks for the manager and returns an error if it is null.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix two problems in PicoDLP driver's error handling on
picodlp_panel_power_on:
- If omapdss_dpi_display_enable() failed, the its error value was not
returned
- If picodlp_i2c_init() failed, dssdev->state was erroneously set to
OMAP_DSS_DISPLAY_ACTIVE
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PicoDLP is a micro projector from TI.
DLP used in OMAP4 is dpp2600 (DLP Pico Projector) The DLP requires
commands to be sent over i2c for configurations. To know more about
dpp2600 commands please visit:
https://focus.ti.com/myti/docs/extranet.tsp?sectionId=403
The picodlp module consists of a dss driver and an i2c_client.
To know more please visit:
http://www.omappedia.org/wiki/PicoDLP_projector_guide
Based on original design from Mythri P K <mythripk@ti.com>
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: squashed commits]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vga_lock lock can be taken in atomic context and therefore
cannot be preempted on -rt - annotate it.
In mainline this change documents the low level nature of
the lock - otherwise there's no functional difference. Lockdep
and Sparse checking will work as usual.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since backlight_types[] isn't modified, let's declare it const. That
was probably the intention of the author of commit bb7ca747f8
("backlight: add backlight type"), via which the "const char const *"
construct was introduced. The duplicate const was detected by sparse.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function duplicates code found in sh_mobile_check_var(). Remove
sh_mobile_lcdc_set_bpp() and call sh_mobile_check_var() instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Move channel initialization to sh_mobile_lcdc_channel_init() and call
the function from sh_mobile_lcdc_probe(). This makes the code more
readable and prepares it for fix/var initialization rework.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Instead of updating the fixed screen information line length manually
after calling fb_set_var() in sh_mobile_fb_reconfig(), update the field
in the .fb_set_par() operation handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Implement .fb_set_par to support frame buffer format changes at runtime.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Instead of failing when the requested fb_var_screeninfo parameters are
not supported, adjust the parameters according to the hardware
capabilities.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
When ICBs are unregistered and later reused they need to be reset to
avoid data corruption. Set the WBF, WF and RF bits to make sure ICBs get
reset properly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Following on Herton's patch "fb: avoid possible deadlock caused by
fb_set_suspend" which moves lock_fb_info() out of fb_set_suspend()
to its callers, correct sh-mobile's locking around call to
fb_set_suspend() and the same sort of deaklocks with console_lock()
due to order of taking the lock.
console_lock() must be taken while fb_info is already locked and fb_info
must be locked while calling fb_set_suspend().
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@kernel.org
A lock ordering issue can cause deadlocks: in framebuffer/console code,
all needed struct fb_info locks are taken before acquire_console_sem(),
in places which need to take console semaphore.
But fb_set_suspend is always called with console semaphore held, and
inside it we call lock_fb_info which gets the fb_info lock, inverse
locking order of what the rest of the code does. This causes a real
deadlock issue, when we write to state fb sysfs attribute (which calls
fb_set_suspend) while a framebuffer is being unregistered by
remove_conflicting_framebuffers, as can be shown by following show
blocked state trace on a test program which loads i915 and runs another
forked processes writing to state attribute:
Test process with semaphore held and trying to get fb_info lock:
..
fb-test2 D 0000000000000000 0 237 228 0x00000000
ffff8800774f3d68 0000000000000082 00000000000135c0 00000000000135c0
ffff880000000000 ffff8800774f3fd8 ffff8800774f3fd8 ffff880076ee4530
00000000000135c0 ffff8800774f3fd8 ffff8800774f2000 00000000000135c0
Call Trace:
[<ffffffff8141287a>] __mutex_lock_slowpath+0x11a/0x1e0
[<ffffffff814142f2>] ? _raw_spin_lock_irq+0x22/0x40
[<ffffffff814123d3>] mutex_lock+0x23/0x50
[<ffffffff8125dfc5>] lock_fb_info+0x25/0x60
[<ffffffff8125e3f0>] fb_set_suspend+0x20/0x80
[<ffffffff81263e2f>] store_fbstate+0x4f/0x70
[<ffffffff812e7f70>] dev_attr_store+0x20/0x30
[<ffffffff811c46b4>] sysfs_write_file+0xd4/0x160
[<ffffffff81155a26>] vfs_write+0xc6/0x190
[<ffffffff81155d51>] sys_write+0x51/0x90
[<ffffffff8100c012>] system_call_fastpath+0x16/0x1b
..
modprobe process stalled because has the fb_info lock (got inside
unregister_framebuffer) but waiting for the semaphore held by the
test process which is waiting to get the fb_info lock:
..
modprobe D 0000000000000000 0 230 218 0x00000000
ffff880077a4d618 0000000000000082 0000000000000001 0000000000000001
ffff880000000000 ffff880077a4dfd8 ffff880077a4dfd8 ffff8800775a2e20
00000000000135c0 ffff880077a4dfd8 ffff880077a4c000 00000000000135c0
Call Trace:
[<ffffffff81411fe5>] schedule_timeout+0x215/0x310
[<ffffffff81058051>] ? get_parent_ip+0x11/0x50
[<ffffffff814130dd>] __down+0x6d/0xb0
[<ffffffff81089f71>] down+0x41/0x50
[<ffffffff810629ac>] acquire_console_sem+0x2c/0x50
[<ffffffff812ca53d>] unbind_con_driver+0xad/0x2d0
[<ffffffff8126f5f7>] fbcon_event_notify+0x457/0x890
[<ffffffff814144ff>] ? _raw_spin_unlock_irqrestore+0x1f/0x50
[<ffffffff81058051>] ? get_parent_ip+0x11/0x50
[<ffffffff8141836d>] notifier_call_chain+0x4d/0x70
[<ffffffff8108a3b8>] __blocking_notifier_call_chain+0x58/0x80
[<ffffffff8108a3f6>] blocking_notifier_call_chain+0x16/0x20
[<ffffffff8125dabb>] fb_notifier_call_chain+0x1b/0x20
[<ffffffff8125e6ac>] unregister_framebuffer+0x7c/0x130
[<ffffffff8125e8b3>] remove_conflicting_framebuffers+0x153/0x180
[<ffffffff8125eef3>] register_framebuffer+0x93/0x2c0
[<ffffffffa0331112>] drm_fb_helper_single_fb_probe+0x252/0x2f0 [drm_kms_helper]
[<ffffffffa03314a3>] drm_fb_helper_initial_config+0x2f3/0x6d0 [drm_kms_helper]
[<ffffffffa03318dd>] ? drm_fb_helper_single_add_all_connectors+0x5d/0x1c0 [drm_kms_helper]
[<ffffffffa037b588>] intel_fbdev_init+0xa8/0x160 [i915]
[<ffffffffa0343d74>] i915_driver_load+0x854/0x12b0 [i915]
[<ffffffffa02f0e7e>] drm_get_pci_dev+0x19e/0x360 [drm]
[<ffffffff8141821d>] ? sub_preempt_count+0x9d/0xd0
[<ffffffffa0386f91>] i915_pci_probe+0x15/0x17 [i915]
[<ffffffff8124481f>] local_pci_probe+0x5f/0xd0
[<ffffffff81244f89>] pci_device_probe+0x119/0x120
[<ffffffff812eccaa>] ? driver_sysfs_add+0x7a/0xb0
[<ffffffff812ed003>] driver_probe_device+0xa3/0x290
[<ffffffff812ed1f0>] ? __driver_attach+0x0/0xb0
[<ffffffff812ed29b>] __driver_attach+0xab/0xb0
[<ffffffff812ed1f0>] ? __driver_attach+0x0/0xb0
[<ffffffff812ebd3e>] bus_for_each_dev+0x5e/0x90
[<ffffffff812ecc2e>] driver_attach+0x1e/0x20
[<ffffffff812ec6f2>] bus_add_driver+0xe2/0x320
[<ffffffffa03aa000>] ? i915_init+0x0/0x96 [i915]
[<ffffffff812ed536>] driver_register+0x76/0x140
[<ffffffffa03aa000>] ? i915_init+0x0/0x96 [i915]
[<ffffffff81245216>] __pci_register_driver+0x56/0xd0
[<ffffffffa02f1264>] drm_pci_init+0xe4/0xf0 [drm]
[<ffffffffa03aa000>] ? i915_init+0x0/0x96 [i915]
[<ffffffffa02e84a8>] drm_init+0x58/0x70 [drm]
[<ffffffffa03aa094>] i915_init+0x94/0x96 [i915]
[<ffffffff81002194>] do_one_initcall+0x44/0x190
[<ffffffff810a066b>] sys_init_module+0xcb/0x210
[<ffffffff8100c012>] system_call_fastpath+0x16/0x1b
..
fb-test2 which reproduces above is available on kernel.org bug #26232.
To solve this issue, avoid calling lock_fb_info inside fb_set_suspend,
and move it out to where needed (callers of fb_set_suspend must call
lock_fb_info before if needed). So far, the only place which needs to
call lock_fb_info is store_fbstate, all other places which calls
fb_set_suspend are suspend/resume hooks that should not need the lock as
they should be run only when processes are already frozen in
suspend/resume.
References: https://bugzilla.kernel.org/show_bug.cgi?id=26232
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@kernel.org
it's annoying and takes up way too much space in dmesg.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Increase delay when polling for tx status. This fixes
the unreliable video decoder i2c register access.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The standard timings parses uses 1:1 dimensions when the ratio in the
EDID data is 0. However, for EDID 1.3 and later the dimensions are 16:10
when the ratio is 0.
Pass the version and revision numbers to get_std_timing() which can then
make the right decision about dimensions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Include linux/module.h to fix below build error:
from drivers/video/mxsfb.c:42:
arch/arm/mach-mxs/include/mach/memory.h:22:1: warning: this is the location of the previous definition
drivers/video/mxsfb.c:574: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/video/mxsfb.c:893: warning: data definition has no type or storage class
drivers/video/mxsfb.c:893: warning: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/video/mxsfb.c:893: warning: parameter names (without types) in function declaration
drivers/video/mxsfb.c:917: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:917: warning: data definition has no type or storage class
drivers/video/mxsfb.c:917: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/video/mxsfb.c:917: warning: function declaration isn't a prototype
drivers/video/mxsfb.c:918: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:918: warning: data definition has no type or storage class
drivers/video/mxsfb.c:918: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/video/mxsfb.c:918: warning: function declaration isn't a prototype
drivers/video/mxsfb.c:919: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:919: warning: data definition has no type or storage class
drivers/video/mxsfb.c:919: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/video/mxsfb.c:919: warning: function declaration isn't a prototype
make[2]: *** [drivers/video/mxsfb.o] Error 1
make[1]: *** [drivers/video] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This is an i2c driver, not a platform driver, thus use "i2c" prefix for
the module alias.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need a callback to do some things after pwm_enable, pwm_disable
and pwm_config.
Signed-off-by: Dilan Lee <dilee@nvidia.com>
Reviewed-by: Robert Morell <rmorell@nvidia.com>
Reviewed-by: Arun Murthy <arun.murthy@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ep93xx_bl.c uses interfaces from linux/module.h, so it should include
that file. This patch fixes build errors:
CC [M] drivers/video/backlight/ep93xx_bl.o
drivers/video/backlight/ep93xx_bl.c:138: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/video/backlight/ep93xx_bl.c:158: error: expected declaration specifiers or '...' before string constant
drivers/video/backlight/ep93xx_bl.c:158: warning: data definition has no type or storage class
...
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds struct s3c_fb_driverdata s3c_fb_data_exynos4 for EXYNOS4
and adds lcd clock gating support.
FIMD driver needs two clocks for FIMD IP and LCD pixel clock. Previously,
both clocks are provided by using bus clock such as HCLK. However, EXYNOS4
can not select HCLK for LCD pixel clock because the EXYNOS4 FIMD IP does not
have the CLKSEL bit of VIDCON0. So, FIMD driver should provide the lcd clock
using SCLK_FIMD as LCD pixel clock for EXYNOS4.
The driver selects enabling lcd clock according to has_clksel which means
the CLKSEL bit of VIDCON0. If there is has_clksel, the driver will not
enable the lcd clock using SCLK_FIMD because bus clock using HCLK is used
a LCD pixel clock.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Enables page fault based detection of mmap writes to the framebuffer,
which allows standard fbdev apps (like the generic fbdev xorg driver)
to work on DisplayLink devices.
Not all bugs are shaken out of the fb_defio path of udlfb, but it's
tantalizingly close, so this seems a good time to enable by default.
Alternatively, option can be disabled when running with an xorg driver
that can more directly communicate damaged regions of the framebuffer
via IOCTL. This is a simpler, higher perf option, when available.
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
By default, udlfb allocates a 2nd buffer to shadow what's across
the bus on the USB device. It can operate without this shadow,
but then it cannot tell which pixels have changed, and must send all.
Saves host memory, but worsens the USB 2.0 bus bottleneck.
This option allows users in very low memory situations (e.g.
bifferboard) to optionally turn off this shadow framebuffer.
Signed-off-by: Stuart Hopkins <stuart@linux-depot.com>
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add __user casting, a missing copy_from_user, and proper boolean
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
For at least one DisplayLink device, the vendor-specific information can
be found in the config descriptor instead of as a separate, device-level
descriptor. This patch searches the current interface (of the current
config descriptor) for the DL vendor-specific descriptor.
Signed-off-by: Andrew Kephart <akephart@akephart.org>
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fixes earlier problems where monitor would not return from blank
Test with any DisplayLink-based USB 2.0 graphics adapter
sudo nano /sys/class/graphics/fb?/blank
and write out single digit FB_BLANK_* code from include/linux/fb.h
Supports on (0), blank (1), suspend (2,3), powerdown (4)
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Fix checkpatch.pl warnings in the surrounding code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it. Also use the
aligned fix.line_length and not the (possible) unaligned xres_virtual.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tormod Volden <debian.tormod@gmail.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it. Also use the
aligned fix.line_length and not the (possible) unaligned xres_virtual.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it. Also use the
aligned fix.line_length and not the (possible) unaligned xres_virtual.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The driver currently BUG()s if the pan parameters passed directly from
userspace are invalid. Return -EINVAL instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The drivers/video/sh_mobile_meram.h header contains unused definitions
and declarations. Move the only used macro to sh_mobile_meram.c, and
remove the header.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To reset the ICB on resume the MExxCTL register needs to be OR'ed with
MExxCTL_WBF | MExxCTL_WF | MExxCTL_RF, no set to that value. Fix this.
This fixes corruption at the bottom of the display when resuming from
runtime PM.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Validate as much of the requested ICB configuration as possible outside
of the mutex-protected region when registering ICBs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of hardcoding register values through the driver, define macros
for individual register bits using the register name and the bit name,
and use the macros.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of restoring registers blindly, restart the LCDC by going
through the startup sequence when resuming from runtime PM suspend. All
registers are now correctly initialized in the right order.
As a side effect, this also gets rid fo a possible panning restore issue
caused by always saving the frame buffer base address registers from set
A instead of the currently active set.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
When the frame buffer base address is changed by a panning operation,
store it in the channel structure. It will be reused when runtime PM
code will use __sh_mobile_lcdc_start().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Splitting the LCDC start code from clock, MERAM and panel management
will make the code usable by runtime PM.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The clock divider pattern is computed based on the dot clock register
value which stores the divider denumerator. However, when using a 1:1
divider ratio, the register is programmed with a value that must not be
interpreted as a denominator. This results in a shift left operation
with a value of 32, which produces undefined behaviour.
Compute the clock pattern using the divider denominator, not the dot
clock register value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The LDINTR register caries both interrupt enable and interrupt status
bits. When setting or clearing interrupt enable bits, write all status
bits to 1 to avoid acknowledging interrupts by mistake.
When acknowledging interrupts, write 1 to all non-triggered interrupt
bits to avoid losing interrupts.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of hardcoding register values through the driver, define macros
for individual register bits using the register name and the bit name,
and use the macros.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Resuming from runtime PM restores all LCDC registers. If the dot clock
is off at that time display panning information will be corrupted.
Turn the dot clock on before resuming from runtime PM. Similarly,
turn the clock off after suspending the LCDC.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
There is no reason for sh_mobile_meram_priv to be in the .h file
since it should be private to sh_mobile_meram.c
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
The MERAM reference counts should be tied to the two LCDC devices (LCD/HDMI)
so that when they are enable/disabled, the MERAM is as well.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
