dtc warns about obviously incorrect GPIO numbers for the audio codec
on both lpc32xx boards:
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
It looks like the nodes are written for a different binding that combines
the GPIO number into a single number rather than a bank/number pair.
I found the right numbers on stackexchange.com, so this patch fixes
the warning and has a reasonable chance of getting things to actually
work.
Cc: stable@vger.kernel.org
Link: https://unix.stackexchange.com/questions/59497/alsa-asoc-how-to-correctly-load-devices-drivers/62217#62217
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GPIO polarity is missing in the hdmi,hpd-gpio property, this
fixes the following DT warnings:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih407-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih410-b2260.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
[arnd: marked Cc:stable since this warning shows up with the latest dtc
by default, and is more likely to actually cause problems than the
other patches from this series]
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This fixes the following warning by also sending the flags argument for
gpio controllers:
Property 'cs-gpios', cell 6 is not a phandle reference in
/ahb/apb/spi@e0100000
Fixes: 8113ba917d ("ARM: SPEAr: DT: Update device nodes")
Cc: stable@vger.kernel.org # v3.8+
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The "dmas" cells for the designware DMA controller need to have only 3
properties apart from the phandle: request line, src master and
destination master. But the commit 6e8887f60f updated it incorrectly
while moving from platform code to DT. Fix it.
Cc: stable@vger.kernel.org # v3.10+
Fixes: 6e8887f60f ("ARM: SPEAr13xx: Pass generic DW DMAC platform data from DT")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
-----BEGIN PGP SIGNATURE-----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=bDG2
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.16, bis
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
* tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable the LCD
ARM: dts: sun8i: a83t: Add LVDS pins group
ARM: dts: sun8i: a83t: Enable the PWM
ARM: dts: sun8i: a83t: Add display pipeline
ARM: sunxi: h3/h5: add simplefb nodes
arm64: allwinner: h5: add compatible string for DE2 CCU
ARM: sun8i: h3/h5: add DE2 CCU device node for H3
dt-bindings: simplefb-sunxi: add pipelines for DE2
ARM: dts: sun8i: fix USB Ethernet of Orange Pi R1
Signed-off-by: Olof Johansson <olof@lixom.net>
According to the comment added to exynos_dt_pmu_match[] in commit
8b283c0254 ("ARM: exynos4/5: convert pmu wakeup to stacked domains"),
the RTC is not able to wake up the system through the PMU on Exynos5410,
unlike Exynos5420.
However, when the RTC DT node got added, it was a straight copy of
the Exynos5420 node, which now causes a warning from dtc.
This removes the incorrect interrupt-parent, which should get the
interrupt working and avoid the warning.
Fixes: e1e146b1b0 ("ARM: dts: exynos: Add RTC and I2C to Exynos5410")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This reverts commit 6737b08140.
Unlike on Exynos5420-family, on Exynos5410 the PMU is not an interrupt
controller so it should not handle interrupts of RTC. The DTC warning
(addressed by mentioned commit) should be fixed by not routing RTC
interrupts to PMU.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The main change here are the series of commits doing the Armada 7K/8K
CP110 DT de-duplication, they include the de-duplication itself and
small fixes in the device tree files.
Besides them there are 2 other patches:
- One adding the crypto support for Armada 37xx SoCs
- An other adding Ethernet aliases on A7K/A8K base boards
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWk+h0CMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71ZU9AKCNLcEcewii
UWPVUzEsQ/+UPojO4wCdHqum9OT33XChVrxHGKP89Dnj1ro=
=HCIC
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.16 (part 2)" from Gregory CLEMENT:
The main change here are the series of commits doing the Armada 7K/8K
CP110 DT de-duplication, they include the de-duplication itself and
small fixes in the device tree files.
Besides them there are 2 other patches:
- One adding the crypto support for Armada 37xx SoCs
- An other adding Ethernet aliases on A7K/A8K base boards
* tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add Ethernet aliases
arm64: dts: marvell: replace cpm by cp0, cps by cp1
arm64: dts: marvell: de-duplicate CP110 description
arm64: dts: marvell: use aliases for SPI busses on Armada 7K/8K
arm64: dts: marvell: use mvebu-icu.h where possible
arm64: dts: marvell: fix compatible string list for Armada CP110 slave NAND
arm64: dts: marvell: fix typos in comment describing the NAND controller
arm64: dts: marvell: use lower case for unit address and reg property
arm64: dts: marvell: fix watchdog unit address in Armada AP806
arm64: dts: marvell: armada-37xx: add a crypto node
ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7
- A few random updates for vf610-zii board: correct switch EEPROM size,
enable edma1, correct GPIO expander interrupt, add PHYs for switch2
device.
- LS1021A device tree updates: add reboot and QSPI device nodes, label
USB controllers, specify interrupt-affinity for PMU, fix TMR_FIPER1
setting, enable esdhc device, add Moxa UC-8410A board support.
- A bunch of patches from Fabio: fix reg - unit address mismatches,
remove leading zero in unit address, move regulators out of
simple-bus, move nodes with no reg property out of bus, remove extra
clock cell, add missing phy-cells to usb-nop-xceiv, etc.
- A couple series from Hummingboard developers: re-organise device tree
files for better handling various board versions, and then add the
new hummingboard2 board support on top of that.
- Disable AC'97 input pins pad and add support for powering off for
imx6qdl-udoo board.
- Convert from fbdev to drm bindings for imx6sx-sdb and imx6sl-evk
board.
- Add device tree for Variscite DART-MX6 SoM and Carrier-board support.
- Add new board support of TS-4600 and TS-7970 from Technologic
Systems.
- A series from Stefan to update imx7-colibri device tree and then add
new version of Toradex Colibri iMX7D board with eMMC support.
- Other random updates on various board support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaTDRSAAoJEFBXWFqHsHzO5qwIAJ9iqSd41KE50kX2QPWa6Uqa
Dfj0BcR4RdFpf4FqCOM6ntjVhUEyxNUtwINuMr6eCI8BK1NGeLNJGm9LK77/RwoE
wmUFTcGelzx4iEWVouD1NoCxIvVFm5RyO26JC/0GPUbulKvcTRma+GQBV218ZOcz
5GYZ2vlmvddwfgNCF+w2tRB07s5kFKWk9S+w7oDd2qF4qztOzBWMr+i5gdtLAboc
iaWS1+9RQu1FbtuanHAbCFmaQrPV2YsDnnIQYMBqpKlFoO7oUSJCDkINWy0BXq7f
eXXLj/hwc8cAC0MM5kuvScEcgKth0p7W0kQETzC19v1EFYx1CxFwFjxXYQ16iCQ=
=1F3D
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree changes for 4.16" from Shawn Guo:
- A few random updates for vf610-zii board: correct switch EEPROM size,
enable edma1, correct GPIO expander interrupt, add PHYs for switch2
device.
- LS1021A device tree updates: add reboot and QSPI device nodes, label
USB controllers, specify interrupt-affinity for PMU, fix TMR_FIPER1
setting, enable esdhc device, add Moxa UC-8410A board support.
- A bunch of patches from Fabio: fix reg - unit address mismatches,
remove leading zero in unit address, move regulators out of
simple-bus, move nodes with no reg property out of bus, remove extra
clock cell, add missing phy-cells to usb-nop-xceiv, etc.
- A couple series from Hummingboard developers: re-organise device tree
files for better handling various board versions, and then add the
new hummingboard2 board support on top of that.
- Disable AC'97 input pins pad and add support for powering off for
imx6qdl-udoo board.
- Convert from fbdev to drm bindings for imx6sx-sdb and imx6sl-evk
board.
- Add device tree for Variscite DART-MX6 SoM and Carrier-board support.
- Add new board support of TS-4600 and TS-7970 from Technologic
Systems.
- A series from Stefan to update imx7-colibri device tree and then add
new version of Toradex Colibri iMX7D board with eMMC support.
- Other random updates on various board support.
* tag 'imx-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (126 commits)
ARM: dts: imx7s: Avoid using label in unit address and reg
ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
ARM: dts: imx6qdl-hummingboard2: Remove leading zero in unit address
ARM: dts: ls1021a: add support for Moxa UC-8410A open platform
ARM: dts: imx51-babbage: Fix the 26MHz clock modelling
ARM: dts: vf610-zii-dev-rev-b: add PHYs for switch2
ARM: dts: vf610-zii-dev-rev-b: fix interrupt for GPIO expander
ARM: dts: vf610-zii-dev: enable edma1
ARM: dts: ls1021a-twr: Remove extra clock cell
ARM: dts: ls1021a-qds: Remove extra clock cell
ARM: dts: imx53: add srtc node
dt-bindings: imx-gpcv2: Fix the unit address
ARM: imx: dts: Use lower case for bindings notation
ARM: dts: imx6q-h100: use usdhc2 VSELECT
ARM: dts: imx6sx: Add support for PCI power domain
ARM: dts: imx6sx: Fix PCI non-prefetchable memory range
ARM: dts: imx6qdl-hummingboard2: rename regulators to match schematic
ARM: dts: imx6qdl-hummingboard2: add v1.5 som with eMMC
ARM: dts: imx6qdl-hummingboard2: add v1.5 som without eMMC
ARM: dts: imx6qdl-hummingboard2: add PWM3 support
...
Clock driver support:
Rework all platforms to use proper clock bindings. Linux should now boot
upstream kernels on ast2400 and ast2500 platforms without out of tree
patches.
New systems:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
We also see updates to the Palmetto and Romulus systems to bring them in
line with the functionality of those above.
The systems take advantage of recently added drivers for LPC Snoop
device and the PWM/Tachometer fan controller.
OpenBMC flash layout:
The flash layout used OpenBMC systems is added and the device trees now
use it.
-----BEGIN PGP SIGNATURE-----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=H9im
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.16-devicetree' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
Pull "ASPEED device tree updates for 4.16" from Joel Stanley:
Clock driver support:
Rework all platforms to use proper clock bindings. Linux should now boot
upstream kernels on ast2400 and ast2500 platforms without out of tree
patches.
New systems:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
We also see updates to the Palmetto and Romulus systems to bring them in
line with the functionality of those above.
The systems take advantage of recently added drivers for LPC Snoop
device and the PWM/Tachometer fan controller.
OpenBMC flash layout:
The flash layout used OpenBMC systems is added and the device trees now
use it.
* tag 'aspeed-4.16-devicetree' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed-evb: Add unit name to memory node
ARM: dts: aspeed-plametto: Add flash layout and fix memory node
ARM: dts: aspeed-romulus: Update Romulus system
ARM: dts: aspeed: Add Qanta Q71L BMC machine
ARM: dts: aspeed: Add Ingrasys Zaius BMC machine
ARM: dts: aspeed: Add Witherspoon BMC machine
ARM: dts: aspeed: Sort ASPEED entries in makefile
ARM: dts: Add OpenBMC flash layout
ARM: dts: aspeed: Update license headers
ARM: dts: aspeed: Remove skeleton.dtsi
ARM: dts: aspeed: Add LPC Snoop device
ARM: dts: aspeed: Add PWM and tachometer node
ARM: dts: aspeed: Add clock phandle to GPIO
ARM: dts: aspeed: Add flash controller clocks
ARM: dts: aspeed: Add watchdog clocks
ARM: dts: aspeed: Add MAC clocks
ARM: dts: aspeed: Add proper clock references
ARM: dts: aspeed: Add LPC and child devices
dt-bindings: gpio: Add ASPEED constants
dt-bindings: clock: Add ASPEED constants
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The A711 has 1024x600 LVDS panel, with a PWM-based backlight. Add it to our
DT.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
MPP7 is currently muxed as "gpio", but this function doesn't exist for
MPP7, only "gpo" is available. This causes the following error:
kirkwood-pinctrl f1010000.pin-controller: unsupported function gpio on pin mpp7
pinctrl core: failed to register map default (6): invalid type given
kirkwood-pinctrl f1010000.pin-controller: error claiming hogs: -22
kirkwood-pinctrl f1010000.pin-controller: could not claim hogs: -22
kirkwood-pinctrl f1010000.pin-controller: unable to register pinctrl driver
kirkwood-pinctrl: probe of f1010000.pin-controller failed with error -22
So the pinctrl driver is not probed, all device drivers (including the
UART driver) do a -EPROBE_DEFER, and therefore the system doesn't
really boot (well, it boots, but with no UART, and no devices that
require pin-muxing).
Back when the Device Tree file for this board was introduced, the
definition was already wrong. The pinctrl driver also always described
as "gpo" this function for MPP7. However, between Linux 4.10 and 4.11,
a hog pin failing to be muxed was turned from a simple warning to a
hard error that caused the entire pinctrl driver probe to bail
out. This is probably the result of commit 6118714275 ("pinctrl:
core: Fix pinctrl_register_and_init() with pinctrl_enable()").
This commit fixes the Device Tree to use the proper "gpo" function for
MPP7, which fixes the boot of OpenBlocks A7, which was broken since
Linux 4.11.
Fixes: f24b56cbcd ("ARM: kirkwood: add support for OpenBlocks A7 platform")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The EB MP board probably has a character LCD but the board manual does
not really state which IRQ it has assigned to this device. The invalid
assignment was a mistake by me during submission of the DTSI where I was
looking for the reference, didn't find it and didn't fill it in.
Delete this for now: it can probably be fixed but that requires access
to the actual board for some trial-and-error experiments.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- New boards:
- Axentia Nattis with Natte power
- sama5d2 PTC ek
- Document and use extended TCB bindings
-----BEGIN PGP SIGNATURE-----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=BW4/
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT for 4.16
- New boards:
- Axentia Nattis with Natte power
- sama5d2 PTC ek
- Document and use extended TCB bindings
* tag 'at91-ab-4.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
ARM: dts: at91: sama5d2_ptc_ek: use TCB0 as timers
ARM: dts: at91: sama5d27_som1_ek: use TCB0 as timers
ARM: dts: at91: sama5d2 Xplained: use TCB0 as timers
ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: vinco: use TCB2 as timers
ARM: dts: at91: ma5d4: use TCB2 as timers
ARM: dts: at91: sama5d4 Xplained: use TCB2 as timers
ARM: dts: at91: sama5d4ek: use TCB2 as timers
ARM: dts: at91: sama5d4: Add TCB2
ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: linea/tse850-3: use TCB0 as timers
ARM: dts: at91: sama5d3xek_cmp: use TCB0 as timers
ARM: dts: at91: kizbox2: use TCB0 as timers
ARM: dts: at91: sama5d3 Xplained: use TCB0 as timers
ARM: dts: at91: sama5d3xek: use TCB0 as timers
ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: kizboxmini: use TCB0 as timers
ARM: dts: at91: cosino: use TCB0 as timers
ARM: dts: at91: acme/g25: use TCB0 as timers
ARM: dts: at91: at91sam9x5cm: use TCB0 as timers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
A random assortment of improvements.
GPIO device nodes are added for the AXP813/AXP818 PMICs, meaning we can
finally use the GPIO pins on the PMICs. The LDOs on the GPIO pins can
also be properly muxed and guarded.
EMAC Ethernet support is enabled for more H3 boards, and also for the
A83T, following the return of the bindings in 4.15, after a last minute
revert in 4.13. This will make the H3/A83T boards much more useful in
headless applications.
Two new boards are introduced. The Orange Pi R1 is a small board with
two Ethernet interfaces (one EMAC-based and one USB-based) and a WiFi
chip. This board is fully supported, with the exception of TV-out on
the expansion header, which will not be enabled by default. The WiFi
chip (RTL8189FTV) requires an out-of-tree driver. The Libre Computer
Board ALL-H3-CC H3 version is a newcomer to the Allwinner SBC space,
which was mostly represented by a bunch of fruit-Pis. It is mostly
supported, with the exception of HDMI and camera sensor interface,
which have not been implemented yet.
Two minor patches enable the audio codec on the A13 Olinuxino, and
HDMI output on the pcDuino3 Nano.
-----BEGIN PGP SIGNATURE-----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=UDxH
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.16
A random assortment of improvements.
GPIO device nodes are added for the AXP813/AXP818 PMICs, meaning we can
finally use the GPIO pins on the PMICs. The LDOs on the GPIO pins can
also be properly muxed and guarded.
EMAC Ethernet support is enabled for more H3 boards, and also for the
A83T, following the return of the bindings in 4.15, after a last minute
revert in 4.13. This will make the H3/A83T boards much more useful in
headless applications.
Two new boards are introduced. The Orange Pi R1 is a small board with
two Ethernet interfaces (one EMAC-based and one USB-based) and a WiFi
chip. This board is fully supported, with the exception of TV-out on
the expansion header, which will not be enabled by default. The WiFi
chip (RTL8189FTV) requires an out-of-tree driver. The Libre Computer
Board ALL-H3-CC H3 version is a newcomer to the Allwinner SBC space,
which was mostly represented by a bunch of fruit-Pis. It is mostly
supported, with the exception of HDMI and camera sensor interface,
which have not been implemented yet.
Two minor patches enable the audio codec on the A13 Olinuxino, and
HDMI output on the pcDuino3 Nano.
* tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: h3: nanopi-m1-plus: fix missing ethernet 0 in aliases
ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Nanopi M1
ARM: dts: sun7i: Enable HDMI on pcDuino3 Nano
ARM: dts: sun8i: a83t: Add I2C device nodes and pinmux settings
ARM: dts: sun8i: a83t: Add I2S controller device nodes
ARM: dts: sun8i-h3: Remove allwinner,leds-active-low for non internal PHY
ARM: dts: sun8i: a83t: Enable Ethernet on two boards
ARM: dts: sun8i: a83t: add dwmac-sun8i device node
ARM: dts: sun8i: h3: enable USB OTG for NanoPi Neo board
ARM: dts: sun8i: h3: Add dts file for Libre Computer Board ALL-H3-CC H3 ver.
ARM: dtsi: axp81x: set pinmux for GPIO0/1 when used as LDOs
ARM: dtsi: axp81x: add GPIO DT node
ARM: dts: sun8i: add support for Orange Pi R1
ARM: dts: sunxi: Add codec for A13 Olinuxino
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable GPIO bank2 for K2L
- Enable QSPI for K2G & K2G-EVM
- Enable UART1/2 for K2G & K2G-EVM
- Enable peripherals for K2G-ICE
- Fix C1 and C2 DTS warnings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rpPb
-----END PGP SIGNATURE-----
Merge tag 'keystone_dts_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
ARM: Keystone DTS update for 4.16
- Enable GPIO bank2 for K2L
- Enable QSPI for K2G & K2G-EVM
- Enable UART1/2 for K2G & K2G-EVM
- Enable peripherals for K2G-ICE
- Fix C1 and C2 DTS warnings
* tag 'keystone_dts_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2l-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-k2e-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-hk-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone: Add missing unit name to interrupt controller
ARM: dts: keystone: Get rid of usage of skeleton.dtsi
ARM: dts: keystone*: Use a single soc0 instance
ARM: dts: keystone*: Standardize license with SPDX tag
ARM: dts: k2g-evm: Enable UART 2
ARM: dts: k2g: Add UART 1 and 2 instances
ARM: dts: keystone: Add generic compatible string for I2C EEPROM
ARM: dts: keystone-k2g-ice: Add DT nodes for few peripherals
ARM: dts: keystone-k2g-evm: Add QSPI DT node.
ARM: dts: keystone-k2g: Move ti,non-removable property to board dts
ARM: dts: keystone-k2g-evm: Fix botched up merge
ARM: dts: keystone-k2g: Add QSPI DT entry
ARM: dts: keystone-k2l: Add the second gpio bank node
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch mostly configures more hardware support:
- Clean-up dts files to remove leading 0x and 0s from binding notation
to remove more dtc compiler warnings
- A series of am437x updates for backlight, to fix inverted pad
pull macro, and to configure power management related OPPs
- Configure n950 and droid 4 command mode LCD panels
- Updates to pandora and gta04 LCD panels
- Add support for am574x-idk
- A series of changes to configure more dra7 related PCIe features
- A series of fixes for am335x-boneblue for WLAN, UARTs and CAN
configuration
- A series of changes to configure dra7 OPPs and VDD supplies
-----BEGIN PGP SIGNATURE-----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=G2ZQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-pt2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of device tree changes for omaps for v4.16 merge window
This branch mostly configures more hardware support:
- Clean-up dts files to remove leading 0x and 0s from binding notation
to remove more dtc compiler warnings
- A series of am437x updates for backlight, to fix inverted pad
pull macro, and to configure power management related OPPs
- Configure n950 and droid 4 command mode LCD panels
- Updates to pandora and gta04 LCD panels
- Add support for am574x-idk
- A series of changes to configure more dra7 related PCIe features
- A series of fixes for am335x-boneblue for WLAN, UARTs and CAN
configuration
- A series of changes to configure dra7 OPPs and VDD supplies
* tag 'omap-for-v4.16/dt-pt2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (29 commits)
Revert "ARM: dts: dra7: Add properties to enable PCIe x2 lane mode"
ARM: dts: am572x-idk: Add cpu0 vdd supply
ARM: dts: am571x-idk: Add cpu0 vdd supply
ARM: dts: dra72-evm-tps65917: Add cpu0 vdd supply
ARM: dts: dra7-evm: Add cpu0 vdd supply
ARM: dts: am57xx-beagle-x15-common: Add cpu0 vdd supply
ARM: dts: dra7: Enable 1.5 GHz operation for the CPU
ARM: dts: dra7: Add MPU OPP supply node
ARM: dts: dra7: Add vbb-supply to cpu and additional voltages
ARM: dts: am335x-boneblue: enable can
ARM: dts: am335x-boneblue: enable usarts
ARM: dts: am335x-boneblue: fix wl1835 IRQ pin
ARM: dts: dra7: Remove deprecated PCI compatible string
ARM: dts: dra76-evm: Enable x2 PCIe lanes
ARM: dts: DRA72x: Use PCIe compatible specific to dra72
ARM: dts: DRA74x: Use PCIe compatible specific to dra74
ARM: dts: dra7: Add properties to enable PCIe x2 lane mode
ARM: dts: am57xx: Add support for am574x-idk
ARM: dts: am43x-epos-evm: Hook dcdc2 as the cpu0-supply
ARM: dts: am437x-idk-evm: Disable OPP50 for MPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix potential dtc warnings on kirkwoods files
Declare a new pin (RB) usbale for NAND controller on Armada 38x
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWjzh4yMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71c6eAKCJWCDib+4j
So2W8yQbI+glOCfjQACfaFGVosbxIilV4+l1bUZJFXHTSSk=
=uIda
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.16-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.16 (part 1)
Fix potential dtc warnings on kirkwoods files
Declare a new pin (RB) usbale for NAND controller on Armada 38x
* tag 'mvebu-dt-4.16-1' of git://git.infradead.org/linux-mvebu:
arm: kirkwood: dts: Use lower case for bindings notation
ARM: dts: armada-38x: Add NAND RB pinctrl information
Signed-off-by: Olof Johansson <olof@lixom.net>
* r8a7745 (RZ/G1E) SoC
- Enable SMP
Fabrizio Castro says "Add DT node for the Advanced Power Management
Unit (APMU), add the second CPU core, and use "renesas,apmu" as
"enable-method"."
* r8a7743 (RZ/G1M) SoC
- Add node for thermal sensor module with thermal-zone support
* r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
- Add:
+ Renesas Core Match Timer (CMT) support
+ Renesas Timer Pulse Unit PWM Controller (TPU) support
+ Renesas PWM Timer Controller (PWM) support
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
- Add sound support
* r8a7743 (RZ/G1M), r8a7745 (RZ/G1E) and r8a7792 (R-Car V2H) SoCs
- Allow DTBs of boards of these SoCs to build without any warnings when
compiled with W=1 using gcc-linaro-5.4.1-2017.05
+ Move nodes which have no reg property out of bus, they don't belong there
+ Also sort sub-nodes of root node to allow for easier maintenance
* r8a7790 (R-Car H2), r8a7791 (R-Car M2-W) and r8a7793 (R-Car M2-N) SoCs
- Correct critical CPU temperature
Chris Paterson says "The current R-Car Gen2 device trees define the CPU
critical temperature as 115°C.
The R-Car hardware manuals state that Tc = –40°C to +105°C. The thermal
sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
This value should also apply to r8a7792 but thermal sensor support has
not been added yet."
* r8a7740 (R-Mobile A1) SoC
- Correct TPU register block size
Geert Uytterhoven says "The Timer Pulse Unit has registers that lie
outside the declared register block. Enlarge the register block size to
fix this.
This was probably based on the old platform code, which also assumed a
register block size of 0x100."
-----BEGIN PGP SIGNATURE-----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=2oL+
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.16
* r8a7745 (RZ/G1E) SoC
- Enable SMP
Fabrizio Castro says "Add DT node for the Advanced Power Management
Unit (APMU), add the second CPU core, and use "renesas,apmu" as
"enable-method"."
* r8a7743 (RZ/G1M) SoC
- Add node for thermal sensor module with thermal-zone support
* r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
- Add:
+ Renesas Core Match Timer (CMT) support
+ Renesas Timer Pulse Unit PWM Controller (TPU) support
+ Renesas PWM Timer Controller (PWM) support
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
- Add sound support
* r8a7743 (RZ/G1M), r8a7745 (RZ/G1E) and r8a7792 (R-Car V2H) SoCs
- Allow DTBs of boards of these SoCs to build without any warnings when
compiled with W=1 using gcc-linaro-5.4.1-2017.05
+ Move nodes which have no reg property out of bus, they don't belong there
+ Also sort sub-nodes of root node to allow for easier maintenance
* r8a7790 (R-Car H2), r8a7791 (R-Car M2-W) and r8a7793 (R-Car M2-N) SoCs
- Correct critical CPU temperature
Chris Paterson says "The current R-Car Gen2 device trees define the CPU
critical temperature as 115°C.
The R-Car hardware manuals state that Tc = –40°C to +105°C. The thermal
sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
This value should also apply to r8a7792 but thermal sensor support has
not been added yet."
* r8a7740 (R-Mobile A1) SoC
- Correct TPU register block size
Geert Uytterhoven says "The Timer Pulse Unit has registers that lie
outside the declared register block. Enlarge the register block size to
fix this.
This was probably based on the old platform code, which also assumed a
register block size of 0x100."
* tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (37 commits)
ARM: dts: r8a7745: Add missing clock for secondary CA7 CPU core
ARM: dts: iwg22d-sodimm: Sound DMA support via DVC on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support via SRC on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support via BUSIF on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support on DTS
ARM: dts: iwg22d-sodimm: Sound PIO support
ARM: dts: iwg22d-sodimm: Enable SGTL5000 audio codec
ARM: dts: r8a7745: Add sound support
ARM: dts: r8a7745: Add audio DMAC support
ARM: dts: r8a7745: Add audio clocks
ARM: dts: r8a7740: Correct TPU register block size
ARM: dts: r8a7743: move timer and thermal-zones nodes out of bus
ARM: dts: r8a7743: sort root sub-nodes alphabetically
ARM: dts: iwg20d-q7-common: Sound DMA support via DVC on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support via SRC on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support via BUSIF on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support on DTS
ARM: dts: iwg20d-q7-common: Sound PIO support
ARM: dts: iwg20d-q7-common: Enable SGTL5000 audio codec
ARM: dts: r8a7792: move timer node out of bus
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds a DT for the Allo.com Sparky SBC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=z7/8
-----END PGP SIGNATURE-----
Merge tag 'actions-arm-dt-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/dt
Actions Semi arm based SoC DT for v4.16
This adds a DT for the Allo.com Sparky SBC.
* tag 'actions-arm-dt-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
arm: dts: owl-s500: Add Sparky
dt-bindings: arm: actions: Add Sparky
dt-bindings: Add vendor prefix for Allo.com
Signed-off-by: Olof Johansson <olof@lixom.net>
4.16, please pull the following:
- Stefan updates the BCM283x DTS to make consistent use of the existing GPIO
defines for the polarity specifier
-----BEGIN PGP SIGNATURE-----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=Xax+
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.16/devicetree' of http://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes for
4.16, please pull the following:
- Stefan updates the BCM283x DTS to make consistent use of the existing GPIO
defines for the polarity specifier
* tag 'arm-soc/for-4.16/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Use GPIO polarity defines consistently
Signed-off-by: Olof Johansson <olof@lixom.net>
The A83T has an LVDS bus that can be connected to a panel or a bridge. Add
the pinctrl group for it.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T has the same PWM block than the H3. Add it to our DT.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The display pipeline on the A83T is mainly composed of the mixers and
TCONs, plus various encoders.
Let's add the first mixer and TCON to the DTSI since the only board I have
can use only the LVDS output on the first TCON. The other parts will be
added eventually.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Use Open Drain flags properly for emulated I2C
- Add the PCI bus to WBD111 and WBD222
- Enable the TVE and panel on DIR-685; the panel driver and
bindings have been merged into the DRI subsystem.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJaPMnJAAoJEEEQszewGV1zWf0P/RCDUnp6twtsD79TshHxvONa
V7V4tVZVKSv1Qq7jjCb/BhrdHBZQ6b4Y12om2bHAwMgVkm+Nq1cQWmIeYsqrzeFj
fb3ozxHrO5jxSptGd3bzHRF5w50t/bBPuJK7eb9Q8lJVItIlDqNKEdw1G0h/W87B
0ARTdWZiPPs395qh97sPZmW0MBrs+aQDAe6IMy3qYS+7RiXwjKoeSftgW6eGIs/q
g9AUA1V0Hh9qkHa/xAilVyU+4v0QZStTQRgP2YoKjnioGWkwl6+YLDz5ac7GXdtz
Bx+qm6v7ORW9gwdjJz8xuLw4vT0PGqTmSCy3RY2orC4tGGRAhfT1/5on8Os/HkRm
JuhvkhRTc1G7tclBZpeVNSbviQP/JVQ36x1xb8waH0h8bTTeTZoyhjQAgm+saLGJ
a4+0Sg/rqKP/nBpfpgb+y2FNPDlwRsFsxA2/WCh61P1wPkXQou4Zf/WtTU4HVvyF
CFddw/pGmsFCDegHHEOnZRkua8jylbPZcDcgRhOAJNHkmADQG3HyZNvp8nX5bS+O
c017tocqoejCJaPcXB5HabEUrh6C1WlvehgDL9SzO3ixUIjHDx21UoqnTLkV/6Nm
ukVk4xr+8bdw5IDX6kLGOAYwqUQXnMl0Pfe9SEVEw8NQh5i3sR0AnLBVo1rqMdIn
sWbXGUuUmd+Vz4944pOK
=4mrI
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-update-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "A second set of Gemini DTS updates for v4.16" from Linus Walleij:
- Use Open Drain flags properly for emulated I2C
- Add the PCI bus to WBD111 and WBD222
- Enable the TVE and panel on DIR-685; the panel driver and
bindings have been merged into the DRI subsystem.
* tag 'gemini-dts-update-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add TVE/TVC and ILI9322 panel to DIR-685
ARM: dts: Add PCI to WBD111 and WBD222
ARM: dts: Flags D-Link DIR-685 I2C bus gpios
The H3/H5 SoCs have a HDMI output and a TV Composite output.
Add simplefb nodes for these outputs.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Use tcb0 for timers as selected in sama5_defconfig.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use tcb0 for timers as selected in sama5_defconfig.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use tcb0 for timers as selected in sama5_defconfig.
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
As TCB2 doesn't have any output pins, use it for timers
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
As TCB2 doesn't have any output pins, use it for timers
Cc: Marek Vasut <marex@denx.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
As TCB2 doesn't have any output pins, use for timers.
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
As TCB2 doesn't have any output pins, use it for timers.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The third TC block is missing from the dtsi. It has no output pins but can
still be used for timers as the IRQ is wired.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use tcb0 for timers as selected in sama5_defconfig.
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use tcb0 for timers as selected in sama5_defconfig.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use tcb0 for timers as selected in sama5_defconfig.
Cc: Antoine Aubert <a.aubert@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use tcb0 for timers as selected in sama5_defconfig.
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use tcb0 for timers as selected in sama5_defconfig.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
